Xendata sx-10v2 lto archive appliance installation and users guide © 2011-2014 xendata, inc. All rights reserved. Xendata is a trademark of xendata limited. Document last modified: 23 april 2014.
Installation and users guide: xendata sx-10 archive appliance page 2 contents notices 1. Introduction 1.1. Overview 1.2. Logical drives 1.3. Specification 1.4. Sx-10 models 2. Control panel and connections 2.1. Front panel 2.2. Rear connections 3. Installation 3.1. Rack mounting 3.2. Desktop mountin...
Installation and users guide: xendata sx-10 archive appliance page 3 notices safety to avoid the possibility of personal injury, be sure to turn off the power to the equipment and disconnect the power cable before removing the cover. Fcc this equipment has been tested and found to comply with the li...
Installation and users guide: xendata sx-10 archive appliance page 4 pcie riser card the pcie riser card requires special disposal, as it contains lead-based solder. Reduction of hazardous substances (rohs) this equipment is compliant with the european rohs directive 2002/95ec as long as used as pro...
Installation and users guide: xendata sx-10 archive appliance page 5 chapter 1. Introduction 1.1 overview the xendata sx-10 archive appliance connects to a network and manages one or two stand-alone lto tape drives or a robotic lto tape library. It supports a wide range of lto libraries with near- l...
Installation and users guide: xendata sx-10 archive appliance page 6 1.2 sx-10 logical drives the sx-10 has three logical drives which are illustrated below. C: is the windows 7 system drive. D: is a removable usb memory stick which is mounted internally in the sx-10. It is suitable as a target for ...
Installation and users guide: xendata sx-10 archive appliance page 7 1.3 specification processor intel xeon e3 quad-core 3.2 ghz ram 32 gb system drive capacity (c:) 1 tb recovery memory (d:) internal removable 16 gb usb memory stick archive disk cache (e:) capacity 4 tb connections to lto drives / ...
Installation and users guide: xendata sx-10 archive appliance page 8 the sx-10-21x models have two 8 gb/s fc ports for direct connection to the lto library: model library connection supported lto devices sx-10-211 fc one external lto tape drive sx-10-212 fc two external lto tape drives sx-10-213 fc ...
Installation and users guide: xendata sx-10 archive appliance page 9 chapter 2. Control panel and connections 2.1 front control panel power push button this is used to apply or remove power from the internal power supply to the appliance. Power-on or power-off by momentarily pressing this button. Po...
Installation and users guide: xendata sx-10 archive appliance page 10 2.2 rear connections the rear of the sx-10-20x models is shown: power connection this connects to a 100v to 240v ac power source using the supplied cable. Ps/2 keyboard and mouse port the upper green port connects to a ps/2 mouse ...
Installation and users guide: xendata sx-10 archive appliance page 11 chapter 3. Installation 3.1 rack mounting the sx-10 may be mounted in a standard 19 inch rack. There is a wide range of rack units on the market which may mean that the assembly procedure will differ slightly. You should refer to ...
Installation and users guide: xendata sx-10 archive appliance page 12 if an internet connection is not available to the sx-10 at this time, alternative activation methods are described in the administrator guide for xendata6 server. 6. The next step is to install device drivers for your lto drives o...
Installation and users guide: xendata sx-10 archive appliance page 13 chapter 4. Power-on and power-off procedures 4.1 system power-on it is important that the lto drive or tape library is powered on and is ready before the sx-10 boots. Please follow the procedure described below. 1. Power on the lt...
