Xerox WC390 - WorkCentre 390 B/W Laser User Manual
Summary of WC390 - WorkCentre 390 B/W Laser
Page 1
User guide 610e34790 w o r k c e n t r e 3 9 0 l a s e r a l l - i n - o n e u s e r g u i d e 390ug.Bk page 1 friday, april 28, 2000 12:13 pm.
Page 2
Prepared by: xerox industrial design human interface graphic design jefferson road henrietta new york ©2000 by xerox limited. All rights reserved. Copyright protection claimed includes all forms and matters of copyrightable material and information now allowed by statutory or judicial law or hereina...
Page 3
U s e r g u i d e iii u s e r g u i d e t a b l e o f c o n t e n t s where do i find it v 1. Getting started 1-1 introduction 1-1 front view 1-2 rear view / inside view 1-3 using the control panel 1-4 using the number keypad 1-7 entering alphanumeric characters 1-8 using the automatic paper feeder ...
Page 4
U s e r g u i d e iv cancelling transmission 3-3 confirming transmission 3-4 4. Receiving a fax 4-1 reception modes 4-1 determining the reception mode 4-2 receiving automatically in fax mode 4-3 receiving manually in tel mode 4-4 receiving automatically in ans/fax mode 4-5 distinctive ring pattern d...
Page 5
U s e r g u i d e w h e r e d o i f i n d i t v where do i find it cd-rom • workcentre 390 installation program • print and scan drivers • pagis pro • textbridge pro 98 • workcentre 390 electronic user guide warranty card • warranty information in addition to this user guide, your workcentre 390 com...
Page 6
U s e r g u i d e vi 390ug.Bk page vi friday, april 28, 2000 12:13 pm.
Page 7
U s e r g u i d e 1.1 1 1 c h a p t e r o n e g e t t i n g s t a r t e d introduction this guide provides reference material for installations where the workcentre 390 is used as a stand-alone machine. If questions arise that are not addressed in this guide, more detailed information is provided in...
Page 8
U s e r g u i d e 1.2 f r o n t v i e w front view note: your machine may look slightly different than the illustration. Automatic paper feeder extension tray paper guides paper exit tray manual paper feeder automatic document feeder document guides automatic paper feeder document exit tray control ...
Page 9
1.3 u s e r g u i d e r e a r v i e w / i n s i d e v i e w 1 rear view / inside view rear view pc cable connector power cord connector ext. Line jack tel line jack usb connector laser printer cartridge cover release buttons (right and left sides) front cover inside view 390ug.Bk page 3 friday, apri...
Page 10
U s e r g u i d e 1.4 u s i n g t h e c o n t r o l p a n e l using the control panel lcd display the display shows the current status of your machine, and guides you through various tasks using a menu system for each operation. Fax resolution use to choose the resolution of transmitted documents. C...
Page 11
1.5 u s e r g u i d e u s i n g t h e c o n t r o l p a n e l 1 menu use to choose or set up special functions. Exit use to exit the current mode or status and return to previous. Copy mode use to copy a document. Up and down use to display the next or previous menu item. Also use to adjust machine ...
Page 12
U s e r g u i d e 1.6 u s i n g t h e c o n t r o l p a n e l report use to print various reports and lists. Stop use to stop an operation at any time. Start use to start a job. Also use to activate the selection shown in the display. Search use to search for numbers in memory. Also use to delete di...
Page 13
1.7 u s e r g u i d e u s i n g t h e n u m b e r k e y p a d 1 using the number keypad as you perform various tasks, you will need to enter names and numbers using the number keypad. For example, when you set up your machine, you enter your name (or your company’s name) and telephone number. When s...
Page 14
1.8 u s e r g u i d e e n t e r i n g a l p h a n u m e r i c c h a r a c t e r s entering alphanumeric characters using the number keypad, locate the button labeled with the character you want. Press that button repeatedly until the correct character appears in the display. Caution: for example, to...
Page 15
1.9 u s e r g u i d e e n t e r i n g a l p h a n u m e r i c c h a r a c t e r s 1 to enter another letter, locate the number keypad button labeled with the letter you want. Press the button repeatedly until the letter appears in the display. If the next letter is printed on the same number keypad ...
Page 16
1.10 u s e r g u i d e u s i n g t h e a u t o m a t i c p a p e r f e e d e r using the automatic paper feeder you can stack paper, envelopes, card stocks, labels, or transparencies in the automatic paper feeder to feed automatically. The automatic paper feeder can hold a maximum of 150 sheets of 2...
Page 17
1.11 u s e r g u i d e u s i n g t h e a u t o m a t i c p a p e r f e e d e r 1 prepare the print material for loading. • for paper and envelopes, flex paper or fan envelopes back and forth. Do not fold or crease the paper. • straighten the edges on a level surface. • for transparencies, refer to t...
Page 18
1.12 u s e r g u i d e u s i n g t h e a u t o m a t i c p a p e r f e e d e r load the print material in the automatic paper feeder. Do not exceed the rated capacity for each type of print material. Do not mix different types of print media. Refer to the following instructions for loading material....
Page 19
1.13 u s e r g u i d e u s i n g t h e a u t o m a t i c p a p e r f e e d e r 1 • load letterhead paper with the design facing you. The top edge of the sheet with the logo should enter the printer first. Adjust the paper guides to the width of the print media. Slide the paper guides until they ligh...
Page 20
1.14 u s e r g u i d e u s i n g t h e m a n u a l p a p e r f e e d e r using the manual paper feeder use the manual paper feeder to feed paper one sheet at a time into your machine. Place the paper in the manual paper feeder and adjust the paper guides to the width of the print material. Slide the...
Page 21
1.15 u s e r g u i d e u s i n g t h e m a n u a l p a p e r f e e d e r 1 ensure that the media is fed into the machine as far as it will go. Press the start button to start manual feeding of the media. If you have more than one page to print, press the start button for each page. 2 3 note: when yo...
Page 22
U s e r g u i d e 1.16 390ug.Bk page 16 friday, april 28, 2000 12:13 pm.
Page 23
U s e r g u i d e 2.1 2 2 c h a p t e r t w o m a k i n g a c o p y making a copy your machine is a high quality copier which offers the following features: • adjustable contrast - the contrast setting can be changed to obtain the best copy quality for documents containing faint markings, dark image...
Page 24
2.2 u s e r g u i d e t o m a k e a q u i c k c o p y • collation -when the copy collate menu option is set to on, the machine sorts the copies. For example, if you print two copies of a three-page document, the machine prints one complete document (page 1, page 2, page 3) before printing a second c...
Page 25
2.3 u s e r g u i d e t o m a k e c o p i e s u s i n g t h e c o p y m e n u f e a t u r e s 2 using the number keypad, enter the number of copies you wish to make. The default setting is 01 copy. Press the start button. The machine copies the document. To make copies using the copy menu features a...
Page 26
2.4 u s e r g u i d e t o m a k e c o p i e s u s i n g t h e c o p y m e n u f e a t u r e s press the copy mode button to display the copy menu. For two or more copies (2 to 99), enter the desired number using the number keypad. Press the reduce/enlarge button to reduce or enlarge the original doc...
Page 27
2.5 u s e r g u i d e t o m a k e c o p i e s u s i n g t h e c o p y m e n u f e a t u r e s 2 press collate if you wish to collate copies. When making multiple copies there are two collate options: on and off. • selecting 1:on will make 1 copy of page 1, 2, and 3 in order, then a second copy of 1,...
Page 28
U s e r g u i d e 2.6 390ug.Bk page 6 friday, april 28, 2000 12:13 pm.
Page 29
U s e r g u i d e 3.1 3 3 c h a p t e r t h r e e s e n d i n g a f a x preparing documents for faxing you can fax documents that are printed on standard letter, legal or a4 size paper. Follow these guidelines to prepare your documents. • remove all staples and paper clips before inserting the docum...
Page 30
3.2 u s e r g u i d e s e n d i n g a f a x m a n u a l l y sending a fax manually adjust the document guides to match the width of the document. Slide the document face down into the automatic document feeder until it is grasped and pulled into the machine. The display alternately reads document re...
Page 31
3.3 u s e r g u i d e c a n c e l l i n g t r a n s m i s s i o n 3 using the number keypad, enter the number of the fax machine to which you wish to send the document. If you make a mistake while entering a number, move the cursor under the incorrect digit by using the right or left buttons, and co...
Page 32
3.4 u s e r g u i d e c o n f i r m i n g t r a n s m i s s i o n confirming transmission a message confirmation report shows whether the transmission was successful and how many pages were sent. When the last page of your document has been sent successfully, the machine beeps and returns to standby...
Page 33
U s e r g u i d e 4.1 4 4 c h a p t e r f o u r r e c e i v i n g a f a x reception modes when used as a stand alone fax machine, your multi-function machine has five reception modes as described below: • fax the machine answers an incoming call and immediately goes into fax receive mode. • tel/fax ...
Page 34
4.2 u s e r g u i d e d e t e r m i n i n g t h e r e c e p t i o n m o d e • ans/fax if the workcentre 390 senses a fax tone, it automatically switches to fax reception mode. However, if a fax is not sensed, the workcentre 390 routes the call to the answering machine. • tel in tel mode, automatic f...
Page 35
4.3 u s e r g u i d e r e c e i v i n g a u t o m a t i c a l l y i n f a x m o d e 4 receiving automatically in fax mode press the receive mode button until the display indicates fax. When a fax call comes in, the machine answers on the selected ring count and receives it automatically. 1 2 note: i...
Page 36
4.4 u s e r g u i d e r e c e i v i n g m a n u a l l y i n t e l m o d e receiving manually in tel mode if you have a regular phone connected to the ext. Line jack on the back of the machine, you can answer voice phone calls and receive faxes manually. Press the receive mode button until the displa...
Page 37
4.5 u s e r g u i d e r e c e i v i n g a u t o m a t i c a l l y i n a n s / f a x m o d e 4 receiving automatically in ans/fax mode to use this mode, you must attach an answering machine to the ext. Line jack on the back of your machine. Press the receive mode button until the display indicates an...
Page 38
4.6 u s e r g u i d e d i s t i n c t i v e r i n g p a t t e r n d e t e c t i o n ( d r p d ) distinctive ring pattern detection (drpd) distinctive ring is a telephone company service which enables the use of a single telephone line to answer several different telephone numbers. The number used to...
Page 39
U s e r g u i d e 5.1 5 5 c h a p t e r f i v e h o w t o p r i n t a n d s c a n printing a document the following procedure describes the general steps required for printing from various windows applications. The exact steps for printing a document may vary depending on the application program you...
Page 40
5.2 u s e r g u i d e p r i n t i n g a d o c u m e n t printing a document make sure that your machine is properly connected to the computer. Verify that you have installed the print driver software for your machine. See installing software in the electronic user guide. Create or open the document ...
Page 41
5.3 u s e r g u i d e p r i n t i n g a d o c u m e n t 5 click on ok to close the properties dialog box. After making any necessary changes to the printing parameters, click on ok to start the print job. 6 7 390ug.Bk page 3 friday, april 28, 2000 12:13 pm.
Page 42
5.4 u s e r g u i d e s c a n n i n g a d o c u m e n t scanning a document to use the wc 390 as a scanner, the following are required: • workcentre 390 twain scanner application installed on the workstation connected to the wc 390. • a twain-compliant image-editing software application (for example...
Page 43
U s e r g u i d e 6.1 6 6 c h a p t e r s i x t r o u b l e s h o o t i n g this section describes troubleshooting for the following areas: • clearing jams • lcd display error messages • print quality problems refer to the specific subsection for a description of the problem and associated solutions...
Page 44
6.2 u s e r g u i d e c l e a r i n g j a m s clearing jams if a document jams while you are sending it, document jam appears in the display. Do not pull the document out of the slot or you may damage your machine. Open the control panel by pulling lightly on the control panel cover. Carefully remov...
Page 45
6.3 u s e r g u i d e p a p e r j a m s i n t h e p a p e r f e e d a r e a 6 paper jams in the paper feed area if a paper jam occurs while you are making a copy or receiving a fax, paper jam appears in the lcd display. Remove the stack of copy paper (if necessary). Remove the jammed paper by carefu...
Page 46
6.4 u s e r g u i d e p a p e r j a m s i n t h e p a p e r f e e d a r e a after you remove the jammed paper, reload the stack of copy paper back into the automatic paper feeder with the print side facing you. Adjust the paper guides to match the width of the paper. 4 390ug.Bk page 4 friday, april ...
Page 47
6.5 u s e r g u i d e p a p e r j a m s i n t h e p r i n t e r o u t p u t a r e a 6 paper jams in the printer output area if the paper jams as it exits to the printer exit tray and most of the paper is visible, pull the paper straight out using both hands. Caution: if there is resistance when you ...
Page 48
6.6 u s e r g u i d e p a p e r j a m s i n s i d e t h e m a c h i n e paper jams inside the machine pull the cover release buttons toward you to open the cover. Remove the laser printer cartridge by lifting it carefully by the handle. Warning: the fuser is hot. Use caution when removing the jammed...
Page 49
6.7 u s e r g u i d e p a p e r j a m s i n s i d e t h e m a c h i n e 6 using both hands, gently pull the paper toward you. Check that there is no other paper jammed inside the printer. Reinstall the laser printer cartridge. Close the front cover. 3 4 5 6 390ug.Bk page 7 friday, april 28, 2000 12:...
Page 50
6.8 u s e r g u i d e t i p s f o r a v o i d i n g p a p e r j a m s tips for avoiding paper jams • by carefully selecting print materials and loading them properly, you should be able to avoid most paper jams. If jams do occur, follow the steps outlined in clearing jams in the electronic user guid...
Page 51
6.9 u s e r g u i d e l c d d i s p l a y e r r o r m e s s a g e s 6 lcd display error messages l c d d i s p l a y m e a n i n g s o l u t i o n retry redial? The machine is waiting for the programmed interval to automatically redial a previously busy station. You can press start to immediately re...
Page 52
U s e r g u i d e 6.10 l c d d i s p l a y e r r o r m e s s a g e s group not available you have tried to select a group location where only a single location number can be used. Group location feature is not available. Line error your machine cannot connect with the remote site, or it has lost con...
Page 53
6.11 u s e r g u i d e l c d d i s p l a y e r r o r m e s s a g e s 6 no. Not assigned the speed dial location you tried to use has no number assigned to it. Assign the number to a speed dial button and try again. Refer to the install guide or electronic user guide for more information no paper the...
Page 54
U s e r g u i d e 6.12 l c d d i s p l a y e r r o r m e s s a g e s paper jam 2 the jammed paper is still inside the unit. Clear the jam. Make sure that the paper edges are not damaged. Ensure that the exit guides are latched on both sides. Refer to clearing jams on page 6.2. Polling error the remo...
Page 55
6.13 u s e r g u i d e p r i n t q u a l i t y p r o b l e m s 6 print quality problems s y m p t o m c a u s e a n d s o l u t i o n the page is white or the printout is too light to read. Toner is low or empty. Refer to replacing the laser printer cartridge in the electronic user guide. Ensure tha...
Page 56
U s e r g u i d e 6.14 p r i n t q u a l i t y p r o b l e m s background scatter on printed pages. The paper may be too damp. Try printing with a different batch of paper. Always store paper in its original sealed package. Do not open packages of paper until necessary so that the paper does not abs...
Page 57
U s e r g u i d e 7.1 7 7 c h a p t e r s e v e n m a i n t e n a n c e clearing memory you can selectively clear information stored in your machine’s memory. Press the menu button. Then press and . The memory clear item appears on the display. Use the up and down buttons to scroll through the list ...
Page 58
7.2 u s e r g u i d e m e m o r y c l e a r i t e m s select the memory item you want to clear by pressing the up or down button repeatedly until the item to be cleared is blinking. Press the start button. Are you sure? Appears in the lcd display. Press to confirm, then press the start button. The s...
Page 59
7.3 u s e r g u i d e c l e a n i n g t h e d o c u m e n t s c a n n e r 7 cleaning the document scanner to keep your machine working properly, occasionally clean the white roller, automatic document feeder (adf) rubber, and the scanning glass. If they are dirty, documents sent to another fax machi...
Page 60
7.4 u s e r g u i d e c l e a n i n g t h e d o c u m e n t s c a n n e r using a cotton swab or a soft dry cloth, clean the adf rubber piece. Carefully wipe the scanning glass with a soft, dry cloth. If the glass is very dirty, first wipe it with a slightly dampened cloth, then with a dry cloth. Be...
Page 61
7.5 u s e r g u i d e c l e a n i n g t h e d o c u m e n t s c a n n e r 7 close the control panel firmly until it clicks into place. Perform shading adjustment. See adjust shading in the electronic user guide. 7 8 390ug.Bk page 5 friday, april 28, 2000 12:13 pm.
Page 62
7.6 u s e r g u i d e r e p l a c i n g t h e l a s e r p r i n t e r c a r t r i d g e replacing the laser printer cartridge pull the cover release buttons toward you to open the cover. Remove the empty laser printer cartridge by lifting it carefully by the handle. Follow the instructions printed o...
Page 63
7.7 u s e r g u i d e r e p l a c i n g t h e l a s e r p r i n t e r c a r t r i d g e 7 unwrap a new laser printer cartridge. Carefully remove the sealing tape. Shake the laser print cartridge as shown five or six times, then from side to side, to distribute the toner evenly. 3 4 5 390ug.Bk page 7...
Page 64
7.8 u s e r g u i d e r e p l a c i n g t h e l a s e r p r i n t e r c a r t r i d g e locate the cartridge slots inside the printer, one on each side. Grasp the handle; slide the laser printer cartridge down between the cartridge slots until it drops into place. Close the cover firmly. Ensure that...
Page 65
7.9 u s e r g u i d e c l e a n i n g t h e d r u m 7 cleaning the drum if print output quality decreases due to the presence of black streaks or ghost images appearing on printouts, drum cleaning should be performed as an attempt to rectify the problem. Press the menu button. Enter clean drum ? App...
Page 66
U s e r g u i d e 7.10 390ug.Bk page 10 friday, april 28, 2000 12:13 pm.
Page 67: I N D E X
U s e r g u i d e i-1 u s e r g u i d e i n d e x i n d e x 8 this is a comprehensive index that incorporates all three manuals -- the ug, the eug, and the ig. Each entry lists the manual in which you will find the required information. The eug was provided to you on your workcentre 390 cd-rom. To a...
Page 68
U s e r g u i d e i-2 i n d e x ig = install guide ug = user guide eug = electronic user guide 256 colors, eug a a standby operation, eug about tab, eug ac power cord, ig 1.2, 1.4 how to connect to computer, ig 1.4 ac power cord, eug adding documents to a standby operation, eug adding documents to t...
Page 69
U s e r g u i d e i n d e x i-3 ig = install guide ug = user guide eug = electronic user guide reports, eug route, eug scan, eug search, eug select, eug send options, eug start, eug stop, eug stop/hold, eug up, down, left, right, eug viewer, eug waste, eug c canadian certification, eug canceling, eu...
Page 70
U s e r g u i d e i-4 i n d e x ig = install guide ug = user guide eug = electronic user guide search button, eug select button, eug speed dial button, eug start button, eug stop button, eug up, down, left, right buttons, eug copy button, ug 1.5 copy menu features, eug copy mode button, eug copy res...
Page 71
U s e r g u i d e i n d e x i-5 ig = install guide ug = user guide eug = electronic user guide entering alphanumeric characters, ug 1.8-9 entering alphanumeric characters, eug entering numbers, eug erasing last fax data, eug error messages, ug 6.9-12 exit, eug exit button, ug 1.5 exit button, eug ex...
Page 72
U s e r g u i d e i-6 i n d e x ig = install guide ug = user guide eug = electronic user guide home resolution, eug home resolution and home contrast, eug i ic, eug ieee standard 1284 specifications, ig 1.4 image control tools, eug file size indicator, eug frame tool, eug prescan button, eug scan bu...
Page 73
U s e r g u i d e i n d e x i-7 ig = install guide ug = user guide eug = electronic user guide level adjustment, eug lineart b/w, eug loading envelopes, ug 1.11-12 loading paper, eug using the automatic paper feeder, eug using the manual paper feeder, eug loading transparencies, ug 1.10-12 local id,...
Page 74
U s e r g u i d e i-8 i n d e x ig = install guide ug = user guide eug = electronic user guide pc parallel cable (parallel cable), ig 1.2, 1.4 how to connect to computer, ig 1.4 usb cable, ig 1.4 phonebook button, eug polling, eug polling one or more remote machines, eug portrait, eug power save, eu...
Page 75
U s e r g u i d e i n d e x i-9 ig = install guide ug = user guide eug = electronic user guide reduce/enlarge, eug copying, eug scanning, eug reduce/enlarge button, eug remote code, eug ren, eug report, ug 1.6 reports, eug help list, eug journal, eug multi-communication, eug phone book, eug schedule...
Page 76
U s e r g u i d e i-10 i n d e x ig = install guide ug = user guide eug = electronic user guide twain scanner help, eug twain scanner program, eug twain scanner window, eug scansoft pagis pro, ig iv installation of, ig 1.11 scanning, ig 2.7 specific information on, ig 2.8 scansoft textbridge pro, ig...
Page 77
U s e r g u i d e i n d e x i-11 ig = install guide ug = user guide eug = electronic user guide stop button, ug 1.6 stop button, eug stop/hold button, eug storing a number for speed dialing, eug storing speed dial numbers for group dialing, eug subject, eug supplies, eug system id, ig 1.10 system nu...
Page 78
U s e r g u i d e i n d e x i-12 ig = install guide ug = user guide eug = electronic user guide width and height indicators, eug windows 2000, ig 1.4, 1.11 windows 98, ig 1.4, 1.11 workcentre 390 twain scanner program, eug x xerox label, eug z zoom in and out tools, eug chap8.Fm page 12 tuesday, may...