1. DL manuals
  2. XFIRE AUDIO
  3. Car Amplifier
  4. XFR1200.4
  5. Owner's Manual

XFIRE AUDIO XFR1200.4 Owner's Manual - Length

Manual is about: XFR series Mobile power amplifiers

Summary of XFR1200.4

  • Page 1

    A u d i o xfr series multi channel mobile power amplifiers owners manual xfireaudio.Com.

  • Page 2: Xfr Series

    Xfr series life amplified introduction welcome to xfire audio ‘‘the new breed of mobile audio’’. Congratulations on purchasing one of the finest autosound power amplifiers in existence. Born in the u.S.A from rigorous pursuits of exceptional sound, strength, performance, and style delivering kick as...

  • Page 3: Specifications

    Specifications rms power output (14.4v 0.15% thd): model @ 2Ω @ 4Ω @ 4Ω bridged xfr2000.5 4x 150 w 1x 400 w 4x 100 w 1x 250 w 2x 300 w 1x 400w xfr2000.4 4x 250 w 4x 150 w 2x 500 w xfr1800.2 2x 450 w 2x 300 w 1x 900 w xfr1200.4 4x 150 w 4x 100 w 2x 300 w customization controls: model lp x-over hp x-o...

  • Page 4: Installation

    Installation actual installation of an xfr amplifier is not a difficult task. However, it takes a few tools, considerable care and precise attention to the instructions in this manual. If you doubt that you are up to the task, or your car proves to require special installation skills, we recommend h...

  • Page 5: Length

    An xfr amplifier needs a few things to be happy in a car : ventilation and a “clean” source of power. Ventilation is important with any mobile amplifier. An amplifier can generate a considerable amount of heat when driven hard, and car interiors can get quite hot in the summer. Be careful when choos...

  • Page 6: Connections

    _ + car battery fuse remote turn on ground use recommended fuse rating ! +b rem gnd head unit connections 1 ground (-) ground connection should be made to the vehicle’s chassis with a clean, bare metal, strong connec- tion keep the length of the ground wires as short as possible. Always use the same...

  • Page 7: Xfr Series

    Bridged min 4ohm ch1 ch2 bridged min 4ohm ch1 ch2 xfr1800.2 - speakerwiring stereo configuration (speakers) - mono bridged configuration (subwoofer) 2 - 8 ohm speaker 4 - 8 ohm sub xfr200.4 / xfr1200.4 - speakerwiring stereo configuration (speakers) - mono bridged configuration (subwoofers) 4 - 8 oh...

  • Page 8: Controls

    Xfr2000.5 right left sub min 2ohm 50hz 250hz 50hz 250hz hpf full hpf full min max min max min max 50hz 250hz 0db 18db 40hz 100hz 0 0 180 0 power protect bridged min 4ohm xfr1200.4 power/ protect min max min max 0db 18db 0db 18db 50hz 250hz 50hz 250hz hpf full lpf hpf full lpf 50hz 250hz 50hz 250hz b...

  • Page 9: Signal Input

    5 line level inputs (rca) these inputs are connectd to the source unit’s line level rca outputs. 6 gain this control is used to match the amplifier’s input sensitivity to the source unit’s output. 7 subsonic this control is used to limit the amount of extreme low frequencies. With this control you c...

  • Page 10: Setting The Controls

    Setting the controls turn the gain level on your amplifier to minimum and set the x-over switch to the full position, turn down the bass boost. Turn the volume on the source unit down before you turn on the power (this will save your speakers if something isn’t right!). Turn the system on, check if ...

  • Page 11: Poor Bass Response

    Poor bass response 1. Check if all speakers are connected with the right polarity, speakers connected out of phase will cancel each other resulting in a poor bass response. 2. Check if the connected speakers/subwoofer(s) are ok, replace if needed. Engine noise 1. Use only high quality shielded rca c...

  • Page 12

    A u d i o xfire audio limited warranty. U.S.A. Warranty: 90 days. (1 year if installed by an authorized dealer.) what is covered: this warranty applies only to xfire audio products sold to consumers by authorized dealers in the u.S.A. Products purchased by consumers from an authorized dealer in anot...