Summary of uno series
Page 1
Uno product quick start guide.
Page 2
Important safety information 1. Read these instructions all the safety and operating instructions should be read before the product is operated. 2. Keep these instructions the safety and operating instructions should be retained for future reference. 3. Heed all warnings all warnings on the product ...
Page 3
1. What’s in the box • the uno series processor model hardware purchased • this hard copy of the quick start guide • usb drive with software, help file, quick start guide, spec sheets • iec socket detachable power cable • detachable 3.5mm euro terminal block connectors 2. What you need to provide • ...
Page 4
4. Hardware: front panel 1. Power status led a blue power status led will light to notify you that the uno device is connected to a power source and switched to the ‘on’ position. 2. Network status led • when the processor has an ethernet cable / network cable connected the orange network status led...
Page 5
Shielded audio cabling. Uno has eight (8) or sixteen (16) switchable mic/line inputs w 48v phantom power depending on the model. 9. Network audio i/o uno series-n and uno series-n-aec model versions include two rj45 dante enabled network audio connectors (not to be confused with the ethernet connect...
Page 6
Processor model must match the uno software module and the uno app processor version being used in the neuconsole software. 7. Initial device connectivity: the uno series of digital processors run on a network based infrastructure and are configured and controlled by a host computer via ethernet usi...
Page 7
Please see - ip reset push button / reset processor network settings instructions below if you are creating a non-dhcp direct or indirect connection. Note : most modern computers can now detect a direct connection so you can use a straight through ethernet cable for the direct connection (if there i...
Page 8
Operation is indicated/displayed only in the software’s network view page – see network view & connection below. (c) upon being powered up the processor will search for a dhcp router or server to obtain an ip address. If it locates dhcp it will connect quickly. If you are using a direct or indirect ...
Page 9
(d) if your processor and software have not connected properly you will see a red or yellow connection indicator to the left of the processor or device model indicating a connection or operational problem. Network connection indicators • green - connected and operational. • yellow – connected but no...
Page 10
Indicator turn green if successful. Solution: if the indicator remains yellow, close the neuconsole software and then re-open. Or reset the processor. Message : device schematic not ready. Solution: the processor has already been loaded with a dsp design. Give the connection process a minute to conn...
Page 11
(f) your devices will appear offline until you assign a static ip address for your pc as described below. (g) once all processors and devices have their own unique ip address we will do the same for your pc in #14 below. 14. A static ip address for your computer - multiple devices – no dhcp: in this...
Page 12
16. Neuconsole software: (project view/design mode) you are able to work with the neuconsole software without being connected to an uno processor (offline) but for the purpose of this guide example we have established a network connection to the uno processor first before beginning to work on a new ...
Page 13
Note: once you are in project view working on a dsp design you are able to switch back and forth between “ project view ” and “ network view ” by selecting the grey network view / project view button at the top right of the work page area. Processor module • from the system components menu under com...
Page 14
(b) to map physical device, right click the red uno u0808 processor module in the work area. Select “map physical device” as shown at right and select the processor device model you are working with from the drop down list . Once done as shown below on page 14, notice that the processor module in th...
Page 15
(5) as shown above, the pre-designed uno app – device design schematic we imported now resides in the u0808 processor module in the work area and when opened it reveals all of its dsp modules and the dsp module schematic layout . New to neuconsole v5.2.1 – we support printing of project system overv...
Page 16
(8) double clicking on the input dsp module provides parameter access to the master input polarity, mute, digital trim & meters. Plus , via a secondary button located within the opened input module, the processors mic/line pre-amp parameter controls – as shown below. (9) click the grey “ mic/line pr...
Page 17
18. Save project: (a) click the “save project” disc located to the right of the zoom control at the top of the project view work area to “ save project as ” or “ save ” your dsp design project (each time a dsp parameter adjustment is made the save project disc will re-appear) or select “save project...
Page 18
(f) note above that the tool bars at the top of the online mode work area page, the opened dsp design layout and the dsp modules are now red (not blue) indicating that you are in online mode. (g) note: you can make parameter adjustments to the dsp modules while in online mode . When you do, upon swi...
Page 19
(a) connect to the processor device. (b) open the neuconsole software. (c) from the neuconsole startup window select start “network view” . (d) in the network view window as shown at the right - make sure the network connection indicator to the left of the processor device model is green (connected ...
Page 20
• for more detailed operational guidance please see the detailed user manual that can be viewed in the neuconsole software” help file”; information saved on the usb drive packaged with each processor (this quick start guide can be found in both locations as well); our website product tutorials; or c...
Page 21
Customer support if you’d like to contact us regarding product support or technical designs, email support@xilica.Com and we’ll connect you with a solutions engineer. Alterna- tively, if you’d like to speak to someone, you can call the following numbers for immediate assistance: north america & rest...