1 rotary hammer model: xp-r40va handling instructions before using this xinpu rotary hammer, please carefully read though these handling instructions. Ensure that you know how the machine works, and how it should be operated. Maintain the machine in accordance with the instructions, and make certain...
2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17.
3 (1) tool (2) part of sds max shank (3) turn staff armor (4) flex sheath (5) speed adjuster knob (6) locked pushbutton (7) function knob (8) left cover (9) orientation staff guage (10) side handle (11) core bit (12) core bit shank (13) drill bit (14) core bit tip (15) oil tank cover.
4 in this operator's manual/or machine’s labels following symbols are used: read the manual carefully. Accordance with essential applicable safety of european directives. Double insulation. Denote risk of personal injury, loss of lifeor damage to the toolin case of nonobservance of the instruction i...
5 general power tool safety warnings warning ： read all safety warnings and all instructions. Failure to follow all warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refer...
6 b) use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. C) avoid accidental starting. Ensure the switch is in the off position before plugging in. ...
7 5) service a) have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Special requirements for hammer - wear ear protectors with impact drills. Exposure to noise can cause hearing loss. - u...
8 standard accessories (1) case (molded plastic)……………………………………………………………1 (2) side handle ………………………………………………………………………1 (3) hexagon bar wrench (for 6mm screw)………………………………………….1 (4) hexagon bar wrench (for 5mm screw)……………………………………… …1 (5) hexagon bar wrench (for 4mm screw)………………………………………….1 (6) screwdr...
9 3. Large dia. Hole boring (rotation + hammering ) (1)drill bit (2) core bit (3) core bit shank(sds－max shank) (1)drill bit ● applied to core bits 30mm to 100 mm (2) core bit ● external dia.30mm,35mm,40mm,45mm,50m,55mm,60mm,70mm，75mm，80mm，85mm，90mm， 95mm 100mm (3) core bit shank ● applied to core b...
10 applications ○ drilling holes in concrete ○ drilling anchor holes ○ crushing concrete, chipping, digging, and squaring (by applying optional accessories) assembly name of the parts (1) flex sheath (2) oil tank cover (3) function knob (4) left cover (5) switch (6) main handle (7) speed adjuster kn...
11 4. How to install tool note: for tools such as a bull point and a cold chisel, use only xinpu genuine parts. (1) to attach the tool (sds max shank), insert it into the hole until it contacts the innermost end of the hole as illustrated in fig.1. If you continue to turn the tool with slight pressu...
12 ○ if the bull point or cold chisel is used at the position of “rotation hammering”, the tool can start to rotate, resulting in unexpected accidents. Make sure that they are used at the position of “hammering”. (1) switching to “hammering” (a) push the locked pushbutton, release lock and turn the ...
13 (3) when the hole depth reaches approximately 5mm, the hole position can be determined. Then remove the dill bit from the core bit and continue the hole drilling job. Caution: when removing the dill bit, always disconnect the plug from the receptacle. 3. How to dismount the core bit ○ by holding ...
14 5. Replacing carbon brushes loosen the two set screws and remove the fan cover. Remove the brush caps and carbon brushes. After replacing the carbon brushes, tighten the brush caps securely and install the fan cover with securely tightening two set screws. 6. Service parts list a: code no. B: ite...
15.
16.
