Xmart STA-16A User Manual
USER MANUAL - STA 16A
___________________________________________________________________________________________________________________________________
www.xmart-ups.com
1701-STA-16 220V- EN
- 4
6. SAFETY
Read carefully this manual and comply with all safety instructions. This product must be installed by qualified technician only. Keep this
manual on hand for any future revisions.
SAFETY & USE:
WARNING: This device must be installed following instruction from this manual.
The manufacturer is not liable for any damage that might rise from misusing this unit or defective installation.
WARNING: This product has been designed to operate safely and reliably for years. Nevertheless, as it is an electrical device, it is required to
read and understand this manual. Keep manuals as references for future consults.
WARNING: This product has been designed to be used indoors, protected of water, direct sun light and extreme temperatures. This device
must not be used outdoors, close to moisture of heat sources.
WARNING: Do not set objects on this equipment. Handle with care. Do not block UPS ventilation.
WARNING: Make sure to connect this unit to proper power line according to selected model. The Technical Specs sticker shows power
rating information. DO NOT connect this device to any of its own power outlets.
WARNING: DO NOT connect life support medical equipments, microwave ovens, vacuum cleaners, refrigerators, or any other appliance to
this device.
WARNING: In case of emergency turn off the UPS pressing Power Button, unplug it and call technical support.
DISPOSAL
We strongly recommend disposing this product according to regulations in your country to prevent possible
environmental damages; besides some parts might be recycled.
7. SAFETY & QUALITY STANDARDS
SAFETY - LOW VOLTAGE DIRECTIVE (2006/95/EC)
IT Equipment-Safety-Part 1: General Requirement
EN 60950-1:2006 + A11: 2010
UPS Part 1-1: General & Safety UPS in accessible areas
IEC/EN 62040-1
ELECTROMAGNETIC COMPATIBILITY - EMC DIRECTIVE (2004/108/EC)
UPS, Part 2, Electromagnetic Compatibility:
IEC/EN 62040-2
Low Freq. Conducted Disturbances & Signals:
IEC/EN 61000-2-2
Electrostatic discharge immunity Test:
IEC/EN 61000-4-2: 2009
Radiated radio Frequency immunity:
IEC/EN 61000-4-3: 2006
+ A1: 2008 + A2: 2010
Electrical Fast Transient / burst immunity:
IEC/EN 61000-4-4: 2004
+A1: 2010
Surge immunity:
IEC/EN 61000-4-5: 2006
IP PROTECTION
IP20 (static)
QUALITY MANAGEMENT:
Manufactured under: ISO 9001 : 2000
ENVIRONMENTAL MANAGEMENT:
Manufactured under: ISO 14001 : 2004
Any modification made by user or operator may affect compliance of the safety and performance certifications listed above. UPS
manufacturer is not responsible of any modification made on the product or its accessories after it is manufactured.
This product is designed to operate in domestic and commercial environment.
Technical information on this manual is property of INTEGRA
.
This manual Information cannot be copied or distributed totally or
partially without written approval of INTEGRA.
INTEGRA can introduce modifications in their products or manuals without further notice. .
INTEGRA is not responsible of mistakes or missing information in this manual.
INTEGRA is not responsible for wrong use a third part can do of this information.
Trademarks and logos in this manual are property of their owners.
USER MANUAL - STA 16A
___________________________________________________________________________________________________________________________________
www.xmart-ups.com
1701-STA-16 220V- EN
- 1
ENGLISH
USER MANUAL: STA-16A
AUTOMATIC TRANSFER SWITCH
1. PRODUCT DESCRIPTION
This is an automatic selector or switch with 2 AC inputs and 1 AC output.
AC output is always connected to the pre-selected AC input (For example Input A). In case input A has a power failure, STA-16A
automatically switches to connect Input B to the output. When STA-16A detects power in input A is reconnected, it switches back to input A.
This device is usually used for 2 main applications:
1.- To offer redundant input for one UPS, connecting 2 different AC lines to STA-16A inputs (A & B) and connecting UPS to the STA-16A
output or
2.- To offer UPS redundant system by connecting 2 different UPS at STA-16A inputs and output powering to the protected system.
FRONT PANEL:
1. SWITCH ON/OFF input A (main)
5. USB (optional for future use)
2. SWITCH ON/OFF input B (secundary)
6. RS232 port (optional for future use)
3. Input Breaker input A
7. Intelligent port for LAN card (optional for future use)
4. Input Breaker input B
8. Operation panel
REAR PANEL:
1. Dry contact output (Relays)
4. AC outlet (capacity 16A)
2. AC outlets (capacity 10A)
5. Input socket "A"
3. AC outlets (capacity 10A)
6. Input socket "B"