1. DL manuals
  2. XNET
  3. Network Hardware
  4. INS2000
  5. Install Manual

XNET INS2000 Install Manual

Summary of INS2000

  • Page 1

    X x n n e e t t n n e e t t w w o o r r k k v v i i d d e e o o s s e e r r v v e e r r i i n n s s t t a a l l l l g g u u i i d d e e xnet network video server ( ins2000 ) install guide ver. 1.0 (090905) 1 / 17.

  • Page 2

    X x n n e e t t n n e e t t w w o o r r k k v v i i d d e e o o s s e e r r v v e e r r i i n n s s t t a a l l l l g g u u i i d d e e 2 / 17 please read this manual thoroughly paying attention to cautions and warnings before using the product even if you have used similar products before. This pro...

  • Page 3: Index

    3 / 17 x x n n e e t t n n e e t t w w o o r r k k v v i i d d e e o o s s e e r r v v e e r r i i n n s s t t a a l l l l g g u u i i d d e e index 1 about xnet ......................................................................................................... 4 1.1. About xnet .................

  • Page 4: 1  About Xnet

    1 about xnet 1 1 . . 1 1 . . A a b b o o u u t t x x n n e e t t xnet is an internet based security and surveillance system that is compatible with various network conditions through easy installation and user interface as well as multi-functional compressor codec such as mjpeg, mpeg-4, and h.264. X...

  • Page 5: 2  About The Product

    2 about the product 2 2 . . 1 1 . . C c o o n n t t e e n n t t s s please make sure the following contents are included when you open the package . Contents description additional info. Xnet product network video server input: 100~240vac 50-60hz power adapter output : 12vdc, 2a ac power cord 2 jack...

  • Page 6

    6 / 17 2 2 . . 3 3 . . F f u u n n c c t t i i o o n n s s a a n n d d d d e e s s i i g g n n a a t t i i o o n n s s 2 2 . . 3 3 . . 1 1 . . F f r r o o n n t t v v i i e e w w figure 2-1 ins2000 front view mic/ audio in audio out analog video out analog video in video input/output : connect input...

  • Page 7

    7 / 17 2 2 . . 3 3 . . 2 2 r r e e a a r r v v i i e e w w figure 2-3. Ins2000 rear view rs-485 and alarm in/out pin description misc. 1 alarm out 2 alarm out select nc/no at menu screen 3 alarm in(+) 4 alarm in(-) select nc/no at menu screen 5 rs485 + 6 rs485 - „ rs-485: when properly connected, yo...

  • Page 8

    Network : this ethernet terminal connects to 10mbps or 100mbps lan through an rj-45 connector. When optional poe is used, the power will be supplied from the network cable. „ link : yellow light indicates that the network is properly connected. „ act : green light indicates that the xnet system conn...

  • Page 9

    9 / 17 2 2 . . 3 3 . . 3 3 c c o o n n n n e e c c t t i i n n g g t t o o a a l l a a r r m m d d e e v v i i c c e e s s alarm input wires from various sensor type (ir, heat, and magnetic) can be connected to alarm in(+)/(-) terminal as shown in figure 2.5. (nc or no of sensor input can be selecte...

  • Page 10: 3  Software Installation

    3 software installation this section provides brief guidelines to install the xnet software quickly and to monitor xnet’s video and audio signals easily. If you have questions about details not explained in this section or if the product is not functioning as described, please refer to faq before co...

  • Page 11

    11 / 17 3 3 . . 2 2 . . I i n n s s t t a a l l l l i i n n g g i i p p - - i i n n s s t t a a l l l l e e r r s s o o f f t t w w a a r r e e a a n n d d c c o o n n f f i i g g u u r r i i n n g g i i p p a a d d d d r r e e s s s s 3 3 . . 2 2 . . 1 1 . . A a b b o o u u t t i i p p - - i i n n ...

  • Page 12

    B. Select the device of which you wish to change the ip address and click (set ip address) button to bring up the following box in figure 3-3. Figure 3-3. Ip address box c. When you enter the ip address and click set button, the box shown in figure 3-4 will appear. Figure 3-4. Select network adapter...

  • Page 13: 4  Using Web Viewer

    4 using web viewer connecting to network devices can be done using internet web browser or “xnet-cms” software. This guide explains about using internet web browser only. For instructions on how to configure network connection using xnet-cms software, please refer to xnet-cms manual, which can be fo...

  • Page 14

    If you forget the administrator’s password, “factory reset” is the only way to regain access. However, since this will retrieve all default settings, you need to configure the network settings using ip installer software again. 14 / 17 4 4 . . 2 2 . . W w e e b b v v i i e e w w e e r r p p a a g g ...

  • Page 15

    Item sub item description capture - captures and saves the current image as a still picture. The image is saved as jpeg file in the following folder: c:₩xnetcapture setting - brings up menu screen. Setup page for each xnet feature can be opened from this menu screen. Please refer to [xnet owner’s ma...

  • Page 16: 5  Specification

    5 specification ins2000 specifications input signal 1ch analog composite input bnc type signal ntsc/pal video signal video signal video output level 1ch video loop back(bnc type, 75ohm, composite) 1.0vp-p main processors 32bit embedded cpu with linux system system memory nand flash memory : 64mb, dd...

  • Page 17

    17 / 17.