Summary of 200 S CC
Page 2
W w w. Xoboat s.Fi.
Page 3
3 xo boats preface congratulations on your new finnish xo boat! We want to thank you for choosing xo and we hope you enjoy the time you spend aboard. The purpose of this manual is to help you operate your boat with safety and pleasure. The manual contains the details of the boat and the associated o...
Page 4
4.
Page 5
5 1 before departure 9 2 general 11 3 warranty 12 4 before using your boat 12 4.1 registration 12 4.2 insurance 12 4.3 training 12 5 boat characteristics and operation 13 5.1 general 13 5.2 principal boat data 13 5.3 maximum recommended number of persons 13 5.4 load capacity 14 5.5 engine and propel...
Page 6
6.
Page 7
7 boat model: xo 200 s cc craft identification number – cin: engine make and model: engine serial number: 1st owner first name: last name: place of domicile: year of purchase: 2nd owner first name: last name: place of domicile: year of purchase: 3rd owner first name: last name: place of domicile: ye...
Page 8
8.
Page 9
9 1 before departure read this user manual carefully. Before each departure, check at least the following: weather and weather forecast take the wind, waves and visibility into account. Is your boat's design category, size and equipment, as well as the skills of the helmsman and crew adequate for th...
Page 10
10
Page 11
11 2 general the purpose of this user manual is to help you familiarise yourself with the characteristics of your new boat. Separate manuals for the equipment installed on the boat are attached and also referred to in a number of sections of this manual. Naturally, you can complement this manual wit...
Page 12
12 3 warranty this boat and the equipment installed by the boatbuilder are covered by a warranty as specified in detail below. The engine, trim tabs, compass, any navigation devices and other ret- rofitted devices are subject to any warranty of their respec- tive manufacturers. Separate warranty car...
Page 13
13 5 boat characteristics and operation 5.1 general this user manual is not intended to be a comprehen- sive maintenance guide or repair manual. Instead, the pur- pose is to help you familiarise yourself with the characteris- tics of your new boat and show you how to use it properly. 5.2 principal b...
Page 14
14 5.4 load capacity the maximum recommended load for xo 200 s cc is 535 kg. An adult's weight is taken to be 75 kg and a child's 37.5 kg. The maximum recommended total weight of the persons on board is 375 kg. In addition to the maximum recommended weight of per- sons mentioned above, the boat can ...
Page 15
15 loading and seating (figure 1) bilge pumps and drainage (figure 2) seat alternative seat electric bilge pump (outboard version) manual bilge pump bilge pump intake and intake hose bilge pump discharge hose.
Page 16
16 of water remains in the bilge so that it cannot be discharged by the bilge pump. Xo 200 s cc is equipped with an automatic, electric bilge pump. It discharges water accumulated in the bilge when the level sensor detects water. The automatic pump is always in the standby mode irrespective of the m...
Page 17
17 ment containing fuel in a place that is not specifically designed for it. At least once a year, check the fuel hoses for wear. 5.7.2 fire-fighting and prevention whenever the xo 200 s cc is used, it must be equipped with fire extinguishers with a minimum fire rating of 8a 68b. The minimum fire ra...
Page 18
18 • smoke or use a naked flame when handling fuel • keep fuel in a space that is not designed for such purpose. If the boat is not equipped with a heater, a spare fuel tank can be stored in place of the heater's tank. • leave the boat unattended when a cooker or heater is in use. 5.8 electrical sys...
Page 19
19 location of electrical equipment: battery compartment main switch bilge pump mast light, white, 360° navigation lights, pop-up switch panel fuse panel (see figure 6) windscreen wiper (option) electrical equipment (figure 4).
Page 20
20 controls (figure 5) switch panel: horn navigation light switch windscreen wiper bilge pump switch aux switch trim tab control, port trim tab control, starboard.
Page 21
21 fuse panel (figure 6) f1 navigation lights f2 horn f3 windscreen wiper f4 12-v power outlet f5 trim tabs, 10 a f6 chart plotter, 10 a f7 radio/cd player, 10 a f8 aux, 10 a f9 radio memory, 5 a f10 bilge pump, 10 a page: 1/1 n ix v a co py ri gh t b y: n:0 11435 revision xo 200 main switch unit b ...
Page 22
22 note! • when retrofitting optional equipment on the boat, use the ‘extra 1’ or ‘extra 2’ circuits. Connect the device to both the power supply and negative wire. Never earth the device to the hull. • if you leave the boat for a longer period, turn the main switch to the off position. Disconnect t...
Page 23
23 warning! Waves impair the boat's handling and can cause it to heel. Take this into account and reduce speed when waves become higher. Learn and obey the rules of navigation on waterways, and also familiarise yourself with the rules known as colregs (internatio- nal regulations for preventing coll...
Page 24
24 5.10 safe operation – other recommendations and information 5.10.1 protection from falling overboard and means of reboar- ding your boat's working decks are indicated in figure 6. Do not sit, stand or stay on any other section of the boat when moving. Before you get underway, make sure that the a...
Page 25
25 working decks and bathing ladder (figure 6) bathing ladder working decks.
Page 26
26 5.10.4 anchoring, mooring and towing always moor your boat carefully, even in sheltered places, because conditions can change rapidly. The mooring lines should be equip- ped with appropriate absorbers to dampen shocks. For the location of fastening points, see figure 7. Do not use other boat comp...
Page 27
27 note! • the tensile strength of the lines or chains should normally not exceed the strength of the fastening point in question. • always attach the tow line so that it can be detached under load. • when towing another boat or being towed, always drive slowly. If the boat you are towing is of the ...
Page 28
28 5.10.5 trailering before lifting your xo boat onto the trailer, make sure that the trai- ler is suitable for your boat: there is a sufficient number of supports to distribute the weight properly without excessive point loads, and the capacity and dimensions of the trailer are sufficient to carry ...
Page 29
29 6 service, repairs and winter storage for information on your boat's maintenance, winter storage, service and repairs, please consult your local xo dealer. If you detect any major damage on the aluminium or surface finish, you should have it repaired by an authorised xo dealer. In case of a probl...
Page 30
30 7 optional equipment 7.1 general note! If not carried out properly, many installation and modification ope- rations can damage the boat structure or create a safety hazard. Please contact the manufacturer before you or somebody else does any of the following: construct new earthing points or hat-...
Page 31
31.
Page 32
32 the boat is marked with a running serial number known as the cin (craft identification number). The cin is marked on the hull, on the starboard side of the stern, on the outer surface of the transom beside the edge strip. You can record the cin of your boat in the table below. When contacting the...
Page 33
33 recommended battery capacity: 100 ah control cables hydraulic steering hoses: 4.50 m (15 ft) engine control cables: 6 m (17 ft) additional load components basic equipment: 15 kg contents of the fixed tanks: 115 kg other load or equipment: – due to reasons associated with the production technology...
Page 34
34 appendix 2 xo 200 s cc – general layout the general layout diagrams of the boat are not to scale. Due to cons- tant development of our boats, the information is subject to change without prior notice. Mast light; white, 360°, 10 w battery compartment, fuse panel and main switch navigation lights;...
Page 35
35 principal data; en iso 8666:2002 a2.1 craft identification; iso 10087:1996 / a1:2000 a2.2 builder's plate: rcd, annex i, 2.2 a2.5 owner's manual; en iso 10240:2004 layout and equipment a2.3 man-overboard prevention; en iso 15085:2003 a3.7 liferaft stowage; rsg guidelines a3.8 escape; - a3.9 ancho...
Page 36
36 appendix 4 wiring diagram 1 2 m_f.1 25a main 1 1 2 m_f.2 25a main 1 1 2 m_f.3 10a bilge p. auto 1 1 2 m_f.4 10a memory 1 m_f:1 m_f: 2 m_f: 3 m_f: 4 i 0 1 2 4487 m_s1 275a/1250a main switch g1 battery 1/1 g1a m_s1a /3.E 6 bilge_p_auto /2.B 6 memory /2.A 1 input+ /3.A 2 input+ m_s1c /20 b. 1 /20 g1...
Page 37
37 a3 1 2 f.1 10a nav./anch. Lt 1 2 1 2 f.2 25a trim 1 2 1 2 f.3 10a horn 1 2 1 2 f.4 10a outlet 1 2 1 2 f.5 10a radio 1 2 4/8 x.2a 5/8 x.2a 6/8 x.2a 7/8 x.2a 8/8 x.2a 1/8 x.2a /1.E3 input+ 1/8 x2a anch. Lt h1 nav. Lt h2 nav. Lt h3 1 3 4 6 5 2 ve a 00c 00000 .2 2/6 5/6 3/6 6/6 3 2 v25a 00 00000 .3 2...
Page 38
38 1 2 f.7 10a wiper stb 1 2 1 2 f.8 7a wiper port 1 2 1 2 f.9 7a aux 1 2 1 2 f.10 10a bilge p. 1 2 1/8 x.2b 2/8 x.2b 3/8 x.2b 4/8 x.2b 2/8 x.2a /1.E4 input+ 2/8 x2a /4.A1 input+ 3 2 v25as00b-00000 s.1 2/6 3/6 1 3 4 6 5 2 vebas00 -00000 s.4 2/6 5/6 1/6 3/6 4/6 6/6 1 3 4 6 5 2 vebas00 -00000 s.5 2/6 ...
Page 39
39 1 2 f.12 10a plotter 1 2 1 2 f.13 10a spare 1 7/8 x.2b /3.A8 input+ 1 2 f.11 10a extra (eng.Bl.) 1 2 5/8 x.2b a.9 plotter /20 b. 1 b1 7/8 x2 b 4/8 x6c 5/8 x6c 1/2 a9 2/2 a9 4/8 x.6c 5/8 x.6c /3.F6 input- 1.5 whit e 1.5 blue plotte r 1.5 blue plotte r 1.5 blue plotte r 1.5 blac k input- 1.5 blac k...
Page 40
40 page: 1/1 n ix v a co py ri gh t b y: n:0 11435 revision xo 200 main switch unit b drawn by modified by pe sub-products: modification description: date 6.5.2011 fuse fuse navigation lt horn fuse wiper 12v dc outlet trim tabs fuse plotter fuse fuse cd player aux memory fuse fuse fuse bilge pump 10...
Page 41
41 page: 1/1 n ix v a co py ri gh t b y: n:0 11431 revision xo 200 switch panel b drawn by modified by pe sub-products: modification description: date 06.05.2011 wiper c (in) s2 2xwhite/blue fuel gauge red 1 ¤ input- e black bilge pump (in) s3 red input- i/j 2xblack x1 bilge pump (out) s3 grey plott...
Page 42
42 1 nav/anc_l_in x2a:4 x6a#1 (8u back view) 2 anc_l_out h1 3 nav/comp_l_out h2, -h3, -h5 4 trim x2a:5 5 horn_in x2a:6 6 horn_out h4 7 8 2635810 1 wiper_sb_in x2b:1 x6b#1 (8u back view) 2 wiper_bb_c m2 3 wiper_bb_i m2 4 wiper_bb_ii m2 5 wiper_bb_in x2b:2 6 wiper_sb_c m1 7 wiper_sb_i m1 8 wiper_sb_ii...
Page 43
43 10 battery+ g1a:1 50/10 m_s1a#1 battery+ m_s1a:1 203 g1a#1 p p 10 input+ b2a:1 50/10 m_s1e#1 10 input- g1d:1 50/8 b2b#1 10 input+ m_s1e:1 50/8 b2a#1 v4100 b2#1 input- b2b:1 204 g1d#1 n n 50 red 2000 mm tam 22 1900 mm 50 red 2000 mm 50 black 700 mm tam 22 1900 mm tam 22 2900 mm included.
Page 44
44 page: 1/1 n ix v a co py ri gh t b y: n:0 11433 revision xo 200 harness c drawn by modified by pe sub-products: modification description: date 6.5.2011 main switch unit navigation light (in) red 1¤ lne+s horn brown lne+s wiper white/blue lne+s 12v dc outlet green/black lne+s plotter blue lne+s tr...
Page 45
45 circuit breaker conn. Switch cable n:o/color size mm2 function n:o amp page: 1/1 n ix v a co py ri gh t b y: n:0 11433dra revision xo 200 diagram c drawn by modified by tum xx modification description: date 23.4.-12 xx.Xx.-xx red 2xblack 50 4 battery switch to engine to engine - input to switch p...
Page 46
46 xo boats oy www.Xoboats.Fi info@xoboats.Fi rantalinna, rantakatu fi-65100 vaasa finland.