1. DL manuals
  2. Xpr
  3. IP Access Controllers
  4. B100PROX-EH-SA v2
  5. Installer Manual

Xpr B100PROX-EH-SA v2 Installer Manual

Manual is about: Standalone Biometric Reader

Summary of B100PROX-EH-SA v2

  • Page 1

    B100prox-eh-sa v2 b100prox-mf-sa v2 standalone biometric reader 1 installer’s manual v. C2.

  • Page 2: Contents

    Contents introduction mounting specifications application diagram recommended swiping technique indication wiring adding admin finger pairing - biometric reader and remote relay unit pairing b100prox-sa v2 with dinrtt pairing b100prox-sa v2 with rtt pairing b100prox-sa v2 with ru2 administrator prog...

  • Page 3: Mounting

    Consult with installer about safety level of the installation. There are devices with relays compatible with this reader that can increase the security of the system if needed. One or two enrolled fingers are enough for one user. Ask the installer before he leaves the site to enroll your finger as adm...

  • Page 4: Specifications

    Fingerprint capacity: prox. Cards capacity: card type: output: push button input: door open time: entry mode: programming: master/admin fingers: backlight on/off: buzzer on/off: firmware upgrade: current consumption: power supply: indication: ip factor: storage/operating temperature : storage/operat...

  • Page 5: Hid

    Nc com no tamp blue yellow red black pink violet orange gray white pb rs485 + _ 12vdc power supply + _ nc com gnd (pb) pb + _ electro magnetic lock green blue yellow red black pink violet orange gray white green colour connection tamper 12v dc red black white yellow grey nc com no gnd green relay (2...

  • Page 6: Adding Admin Finger

    6 adding admin finger 1.Push dip switch no.2 in position on. 2.Reset the power of the device. 3.Wait for one long + multiple short beeps 4.Put the dip switch in position off. (short beeps will stop) 5.Wait for about 15 seconds for the led to blink in orange. 6.Swipe the master finger min.6 times. (un...

  • Page 7

    B (rs485) a (rs485) 1. Close the jumper. Dinrtt beeps continuously and the red led blinks. 2. Open the jumper 3. Wait for beep + ok beep (short + short + long beep) after the ok beep, the coupling is done. Pb2 gn d pb1 gn d n c1 co m n o1 n c2 co m n o2 a b ta mp ta mp rs485 g n d +12v g n d +12v ex...

  • Page 8: Administrator Programming

    8 short beep swipe admin finger 1 time action wait 5 seconds (until fast blinking) swipe user finger min. 6 times (until short + long beep) finger backlight buzzer sound x 1 use point fingers as administrator and installer. You can use the other fingers as access fingers. Administrator finger is enrolle...

  • Page 9: Delete Finger

    Swipe admin finger 4 times action wait 5 seconds (until fast blinking) swipe user finger finger backlight buzzer sound x 4 delete finger slow blinking fast blinking short beep short + long beep short beep x 1 present card/tag 1 time short + long beep x 1 or fast blinking swipe admin finger 5 times a...

  • Page 10

    Add finger relay 1 (on board) 1 swipe add finger relay 2 (remote) add finger relay 1&2 delete finger change admin finger enroll installer finger 2 swipes 3 swipes 4 swipes 5 swipes 6 swipes wait 5 seconds (until fast blinking) swipe new finger min. 6 times or present card/tag swipe already enrolled ...

  • Page 11: Set Relay 1 Time (On Board)

    Short beep swipe installer finger 1 time action swipe the installer finger and start counting seconds finger backlight buzzer sound set relay 1 time (on board) slow blinking fast blinking beeps on 1 second short beep installer programming x 1 swipe the installer finger to stop or wait 30 seconds to ...

  • Page 12

    12 set relay 1 time (on board) 1 swipe set relay 2 time (remote) buzzer on/off backlight on/off 2 swipes 3 swipes 4 swipes wait 5 seconds (until fast blinking) swipe the installer finger 1 to 4 times depending of the desired menu end end end end installer programming block diagram swipe the installe...