1. DL manuals
  2. Xpresskit
  3. Car Alarm
  4. PKUCG2X
  5. Installation Manual

Xpresskit PKUCG2X Installation Manual

Manual is about: Chrysler 2nd Gen And GM Passkey 3+ Type Rf Transponder Bypass

Summary of PKUCG2X

  • Page 1

    Installation guide model: pkucg2x chrysler 2nd gen and gm passkey 3+ type rf transponder bypass product features gm: cover all new gm equipped with the gm pass- key iii plus chrysler: built in mux wire (2nd start & 2nd accessory) activation output to streamline installation activates chrysler starte...

  • Page 2

    Model: pkucg2x rev.: 20091028 © 2008 directed electronics. All rights reserved..

  • Page 3

    2008 2007 2006 2005 2004 2003 enclave d d d d d lucerne cts dts d d d d d d d d d d d d escalade srx avalanche cobalt equinox d expressvan d hhr d d d impala d d d malibu d d d d malibumaxx d d d d montecarlo d d silverado d d suburban d d tahoe d d 300/300c c a / b a / b a / b a / b a / b a / b a /...

  • Page 4

    Red green blue v iolet black v iolet/white pink pink/white brown orange 10 pin harness (-) t o ground when running output (status) ground batt + 12v input input input n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c or alarm system remote control wire guide: connections t o program the module, see page 7 sec...

  • Page 5

    Red blue black brown orange 10 pin harness (-) t o ground when running output (status) ground batt + 12v input input input n/c n/c or alarm system remote control wire guide: connections section b section c section a - 3 or 5 turns of loop are required. - y ou can program the transponder only once. -...

  • Page 6

    Install “c”: for chrysler & dodge & jeep 2008 vehicles 10 pin harness section a - 3 or 5 turns of loop are required. - y ou can program the transponder only once. - do not install on metal surface. Red green blue v iolet black v iolet/white pink pink/white brown orange ground batt 12v + input input ...

  • Page 7

    Step 5 step 4 step 1 step 2 remove the wireless ignition node from the dashboard. (disassemble the dash to access the ignition barrel) step 8 step 6 step 7 slide open the cover of the wireless ignition node. Cut the lip off the cover. Insert the chwfr circuit board as shown. Ensure the board is well...

  • Page 8

    Ign on off turn the key off and remove the key. Remove the brown wire from ground and connect to (-) ground when running (status) output from remote starter. Section c the pkucg2x is compatible with 2004 dodge durango. However, all durango’s built prior to 5 / 17 / 2004 must get a wcm module upgrade...

  • Page 9

    87 87a 30 86 85 relay red green blue v iolet black v iolet/white pink pink/white brown orange 10 pin harness (-) t o ground when running output (status) ground batt + 12v input input input n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c ignition (see next page for wire color) +12v constant a...

  • Page 10

    (-) /(+) i/o status wire color specific wire connection location connect location wire guide: connections 10 pin harness constant (+) 12 volt source chassis ground legend: rcs = remote control system n/c = no connection n/a = not applicable brown rcs red input input (+) vehicle black input (-) vehic...

  • Page 11

    Model: pkucg2x rev.: 20091028 © 2008 directed electronics. All rights reserved..

  • Page 12

    Limited one-year consumer warranty for a period of one year from the date of purchase of a directed electronics remote start or security product, directed electronics. (“directed”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote ...