Summary of T2008
Page 1
® 1 /10 luxury touring car.
Page 2
2 before you start the t2‘008 is a high-competition, high-quality, 1/10-scale touring car intended for persons aged 16 years and older with previous experience building and operating rc model racing cars. This is not a toy; it is a precision racing model. This model racing car is not intended for us...
Page 3
3 important notes – electrical • insulate any exposed electrical wiring (using heat shrink tubing or electrical tape) to prevent dangerous short circuits. Take maximum care in wiring, connecting and insulating cables. Make sure cables are always connected securely. Check connectors for if they becom...
Page 4
4 symbols used l=r 2x ca oil correct wrong overtightened the threads are stripped. Part bags used assemble left and right sides the same way assemble in the specified order pay attention here assemble as many times as specified (here twice) apply ca glue tools required equipment required equipment i...
Page 5
5 kit the xray t2’008 comes partially pre-assembled. Before starting assembly, disassemble the chassis parts, noting the position and orientation of the parts, particularly the bulkheads. Keep the parts, including the screw hardware, close at hand. In the assembly steps that follow, each section beg...
Page 6
6 966080 c 8 963030 st 3x8 930138 ba 3x8 930508 bb 5x8 930120 b 2.4 30 5006 t2‘008 eu rubber-spec composite ball differential - set 30 5007 t2‘008 us foam-spec composite ball differential - set 30 5017 t2‘008 composite diff output shafts (2) 30 5037 t2‘008 composite diff driveshaft adapters (2) 30 5...
Page 7
7 ball differential & front solid axle composite front solid axle (eu rubber-spec only) front & rear axles important: when you build the differential, do not tighten it fully initially; the differential needs to be broken in properly. When you build the diff tighten it very gently. When you put the ...
Page 8
8 302019 2. Front & rear suspension bag 02 30 2033 t2 alu nut for suspension holder (2) 30 2044 t2 lower suspension holders (2+2+2) 30 2163 t2‘008 front suspension arm - hard - rubber-spec - 1-hole 30 2164 t2‘008 front suspension arm - extra-hard - foam-spec - 1-hole 30 3129 composite set of wheelba...
Page 9
9 rear downstop adjustment front downstop adjustment 903306 sfh m3x6 901308 sb m3x8 901408 sb m4x8 901308 sb m3x8 901408 sb m4x8 rear arms #303163 eu rubber-spec - hard (h) #303164 us foam-spec - extra-hard (xh) front arms #302163 eu rubber-spec - hard (h) #302164 us foam-spec - extra-hard (xh) rear...
Page 10
10 track width adjustment wheelbase adjustment roll center adjustment dive adjustment toe-in adjustment track width adjustment wheelbase adjustment roll center adjustment squat adjustment detail detail 2. Front & rear suspension 47.5 mm 3x16mm 50.5 mm thin black steel shim 3 x 7.5 x 0.75mm use only ...
Page 11
11 3. Central transmission bag 30 2023 t2‘008 alu upper bulkhead 30 2078 t2‘007 set of composite hubs for bulkheads (4+2) 30 2087 t2‘008 shock tower front 3.0mm graphite 30 3046 t2‘008 rubber-spec rear upper deck graphite 30 3047 t2‘008 foam-spec rear upper deck graphite 30 3096 t2‘008 shock tower r...
Page 12
12 gearing adjustment 902304 sh m3x4 965050 c5 981210 p 2x10 940510 bb 5x10x4 spur gears #305778 spur gear 78t / 48p #305781 spur gear 81t / 48p #305784 spur gear 84t / 48p #305787 spur gear 87t / 48p #305790 spur gear 90t / 48p #305882 spur gear 112t / 64p #305884 spur gear 114t / 64p #305886 spur ...
Page 13
13 902306 sh m3x6 902306 sh m3x6 902306 sh m3x6 l=r l=r us foam-spec rear upper deck position the rear upper deck inside of the rear drive belt ! Important 3. Central transmission eu rubber-spec rear upper deck.
Page 14
14 ackermann adjustment front toe-in adjustment bag 30 1159 alu countersunk shim (4) 30 1183 t2‘008 rubber-spec upper deck graphite 30 1184 t2‘008 foam-spec upper deck graphite 30 2504 xray quick-saver™ - adjustable servo saver set 30 2511 xray quick-saver - composite servo saver parts 30 2551 servo...
Page 15
15 ackermann adjustment steering throw symmetry chassis flex setting top deck flex setting 307455 pb 5mm 902310 sh m3x10 902306 sh m3x6 903306 sfh m3x6 930407 bb 4x7x2.5 ! Important these rear alu stands are recommended for use only on the us foam-spec chassis, when running foam tires on extra high-...
Page 16
16 901302 sb m3x2.5 981210 p 2x10 drive shafts #305323 us foam-spec - 50mm #305324 eu rubber-spec - 52mm 1.5mm allen wrench 4x 902310 305324 (eu rubber-spec) 305323 (us foam-spec) 902205 901304 303411 901303 303431 302486 (eu rubber-spec) 302484 (us foam-spec) 303411 902306 303454 901308 303454 3053...
Page 17
17 caster adjustment rear toe-in adjustment camber adjustment 902205 sh m2x5 940510 bb 5x10x4 981210 p 2x10 902205 sh m2x5 940510 bb 5x10x4 981210 p 2x10 902310 sh m3x10 wheel hubs #305350 alu - offset 0 mm #305351 alu - offset -0.75 mm #305352 alu - offset +0.75 mm #305353 alu - offset +1.5 mm 53.5...
Page 18
18 roll-center adjustment 902306 sh m3x6 902314 sh m3x14 307455 pb 5mm 901304 sb m3x4 303122 shim 3x6x1 303123 shim 3x6x2 902310 sh m3x10 eu rubber-spec 0° outboard toe-in suspension blocks us foam-spec eu rubber-spec left suspension block = right suspension block l=r 5. Front & rear transmission 1:...
Page 19
19 roll center adjustment 902306 sh m3x6 902314 sh m3x14 307455 pb 5mm 901304 sb m3x4 eu rubber-spec use the alu 3x6x1mm shim (from the last aid bag) only when running on asphalt. When using these shims, use the upper roll center positions on the front shock tower. Us foam-spec do not use alu shim. ...
Page 20
20 ackermann adjustment anti-roll bars adjustment 307455 pb 5mm 902310 sh m3x10 901308 sb m3x8 901303 sb m3x3 901304 sb m3x4 902310 sh m3x10 4x 2x us foam-spec eu rubber-spec 5. Front & rear transmission 3x3mm 3x3mm 3x4mm free movement free movement 1.5mm assembly view when the bars are set, verify ...
Page 21
21 anti-roll bars adjustment 901303 sb m3x3 901304 sb m3x4 902310 sh m3x10 rear anti-roll bar (eu rubber-spec only) 5. Front & rear transmission 3x4mm 3x3mm 3x3mm assembly view only tighten enough to remove excessive free play; anti-roll must still move freely. Wire should be flush with end of pivot...
Page 22
22 8,9Ê-*, - ÎänÎÇÎ ÊrÊÓ°ÓÊÓ® ÎänÎÇ{ ÊrÊÓ°{ÊÓ® ÎänÎÇx ÊrÊÓ°ÈÊÓ® ÎänÎÇÈ ÊrÊÓ°nÊÓ® ÎänÎÇÇ ÊrÊΰäÊÓ® ÎänÎÇn ÊrÊΰÓÊÓ® ÎänÎÇ ÊrÊΰ{ÊÓ® 8,9Ê-*, - ÎänÎä -*, Ê- /ÊÓ{® ÎänÎÎ £{Ê ®Ê9 "7ÊÊ-1* ,-"/ÊÊ{® ÎänÎ{ £Ç°xÊ ®Ê7/ ÊÊ-"/Ê{® ÎänÎx ÓÓ°xÊ ®Ê 1 ÊÊ-"/ 1Ê{® ÎänÎÈ ÓnÊ ®Ê6" /Ê...
Page 23
23 -" Ê* /-Ê"Ê-" Ê * -" Ê"- ÎxÓ£ä £ääv-ÌÊ8,9ÊÓä7® ÎxÓ£x £xäv-Ì ÎxÓÓä Óääv-ÌÊ8,9ÊÓx7® ÎxÓÓx Óxäv-Ì ÎxÓÎä Îääv-Ì ÎxÓÎx Îxäv-ÌÊ8,9ÊÎä7® ÎxÓ{ä {ääv-Ì ÎxÓ{x {xäv-Ì ÎxÓxä xääv-Ì ÎxÓÈä Èääv-ÌÊ8,9ÊÎx7® ÎxÓÇä Çääv-Ì ÎxÓnä nääv-Ì ÎxÓä ääv-Ì ÎxÎä£ £äääv-ÌÊ8,9Ê{ä7® ÎxÎäÓ Óää...
Page 24
24 -" Ê* Ê 1-/ / -*, Ê,/ Ê- /" / Ê/*Ê ➊ ➋ ➌ ➍ ÜÊÌ ÃÊÌiv ÊÌ«ÊÌÊ«À«iÀÞÊÃÌ>Ê«ÛÌÊl>ÃÊ ÌÊÌ iÊÌ«Ê«ÛÌÊ>`ÊlÌÌÊl>ÊÌ° *>ÀÌÃÊ ii`i`\ uÊÎÊÝÊ£ÈÊ-ÊÃvÀiÜ uÊÎÊà ÌiÊ Ì >ÌÊ Ì iÊ v«ÃÌiÊ «>ÀÌÃÊ >ÛiÊ ÌÜÊ Ã`iÃ]Ê Ìvi>liÊ>ÀÕ`ÊÌ iÊ«ÛÌÊl>Ê i\ÊiÊÃ`iÊ >ÃÊ>Êà ÞÊwÊÃ...
Page 25
25 bag 30 1202 t2 composite bumper 30 1218 t2 composite upper holder for bumper 30 1322 t2 front body mount set 6mm 90 2306 hex screw sh m3x6 (10) 90 3308 hex screw sfh m3x8 (10) 90 3310 hex screw sfh m3x10 (10) 96 0030 nut m3 (10) 98 1212 pin 2x12 (10) 30 1222 t2 foam bumper 30 8302 t2‘008 xray sho...
Page 26
26 shock position adjustment ride height adjustment droop adjustment 903308 sfh m3x8 981212 p 2x12 902306 sh m3x6 front shock (light-purple spring - us foam-spec) l=r front shock (c2.8 spring - eu rubber-spec) initial position eu rubber-spec = us foam-spec optional to make the car more stable and ea...
Page 27
27 shock position adjustment ride height adjustment droop adjustment bag 07 902306 sh m3x6 981212 p 2x12 902308 sh m3x8 l=r 308302 902306 902308 981212 301332 optional: to make the car more stable and easier to drive, move the front shocks forward. Stability increases mainly in chicanes. Note that t...
Page 28
28 bag 08 902308 sh m3x8 903306 sfh m3x6 306219 shim 3x6x1 306219 shim 3x6x2 306219 shim 3x6x3 for improved weight balance, we recommend using a narrow, light servo. 306310 960140 from servo 306219 not included not included 306300 902308 306200 not included 903308 903306 903306 903308 306131 902306 ...
Page 29
29 gearing adjustment 902306 sh m3x6 903308 sfh m3x8 903306 sfh m3x6 903308 sfh m3x8 8. Final assembly double-sided tape (not included) receiver (not included) speed controller (not included) feed the receiver wire into the antenna tube 3x8mm 3x6mm 3x8mm pinion (not included) motor (not included) wh...
Page 30
30 ride height adjustment droop adjustment foam tire tips 960140 n m4 detail 8. Final assembly warning! Follow the adhesive manufacturer's instructions for proper use and safety. Wear proper eye and hand protection. Ca make sure the wheel nuts are very tight, so the wheels do not loosen during racin...
Page 31
Pinion / t spur gear / t final drive ratio rollout race track name city / country contact one way differential yes solid one way diff. Middle one way pulley fixed one-way solid axle yes yes transmission loose medium tight diff. Loose medium tight rear front track condition traction technical mixed a...
Page 32
Xray, k vÝstavisku 6992, 91101 trencin, slovakia, europe phone: +421-32-740 11 00, fax: +421-32-740 11 09, info@teamxray.Com xray, k vÝstavisku 6992, 91101 trencin, slovakia, europe phone: +421-32-740 11 00, fax: +421-32-740 11 09, info@teamxray.Com xray, k vÝstavisku 6992, 91101 trencin, slovakia, ...