Summary of T4 2018
Page 2
2 before you start the t4 is a high-competition, high-quality, 1/10-scale touring car intended for persons aged 16 years and older with previous experience building and operating rc model racing cars. This is not a toy; it is a precision racing model. This model racing car is not intended for use by...
Page 3
3 important notes – electrical • insulate any exposed electrical wiring (using heat shrink tubing or electrical tape) to prevent dangerous short circuits. Take maximum care in wiring, connecting and insulating cables. Make sure cables are always connected securely. Check connectors for if they becom...
Page 4
4 not included to ensure that you always have access to the most up-to-date version of the xray set-up book, xray will now be offering only the digital online version on our website www.Teamxray.Com. By offering this online version instead of including a hardcopy printed version in kits, you will al...
Page 5
5 ca at the beginning of each section is an exploded view of the parts to be assembled. There is also a list of all the parts and part numbers that are related to the assembly of that section. The part descriptions are color-coded to make it easier for you to identify the source of a part. Here are ...
Page 6
6 1. Gear differential & front solid axle use tweezers to insert pin. 981210 p 2x10 981210 p 2x10 972050 o 5x2 972050 o 5x2 964050 s 5x15x0.3 964050 s 5x15x0.3 ➊ ➋ ➌ ➍ ➍ ➍ ➎ ➎ ➊ ➋ ➌ ➍ ➎ detail ➎ step step detail 30 4900 xray gear differential - set 30 4910 composite gear diff. Case & cover 30 4930 c...
Page 7
7 964031 s 3.5x10x0.2 1. Gear differential & front solid axle 1. Gear differential & front solid axle 971240 o 24x0.7 after disassembling the gear diff the large o-ring may have an increased size and may be more difficult to re-install. We recommend either inserting the old o-ring carefully in the d...
Page 8
8 composite front solid axle front & rear axles 1. Gear differential & front solid axle 902310 sh m3x10 941015 bb 10x15x4 941015 bb 10x15x4 oil oil oil 903256 sfh m2.5x6 tighten the screws equally but do not tighten them completely. Finish tightening in this order. ➊ ➋ ➌ ➍ note orientation detail be...
Page 9
9 305188 940510 965050 304900 903306 903310 903306 903306 903304 303003-o 302034-o 303001-o 902306 902306 902306 305577 303085 981212 305784 940510 301145 903306 303002-o 902306 902306 902306 305446 960030 305432 302034-o 302760-o 302761-o 302761-o 302760-o 302034-o 302084 302062 302062 305521-k 902...
Page 10
10 gearing adjustment 902304 sh m3x4 965050 c5 981212 p 2x12 940510 bb 5x10x4 903306 sfh m3x6 903304 sfh m3x4 960030 n m3 903310 sfh m3x10 902306 sh m3x6 note orientation note orientation short belt long belt bearing oil (hudy #106230) oil oil bearing oil (hudy #106230) ➊ ➋ 3x10 3x6 3x6 3x6 3x6 3x6 ...
Page 11
11 902306 sh m3x6 902306 sh m3x6 may be used when the front belt becomes worn and loose. Belt tensioner is not included in the kit and must be purchased separately. #303071 belt tensioner set to tighten front belt: rotate both front nylon hubs in arrow direction b to tighten rear belt: rotate both r...
Page 12
12 bag 03 for better stability and to make the car easier to drive, optional #302190 and #303190 graphite stiffeners may be used on the suspension arms. Using only 4 screws, each graphite stiffener can be installed or removed which will completely change the characteristics of the car. Stiffeners ma...
Page 13
13 901310 sb m3x10 901408 sb m4x8 901308 sb m3x8 901408 sb m4x8 front downstop adjustment rear downstop adjustment 2x 2x 2x rear arms - standard #303168 hard option #303169 graphite included rear arms - ars™ #303170 hard included #303171 graphite option front arms #302168 hard option #302169 graphit...
Page 14
14 toe-in track-width wheelbase roll center anti-squat pro-squat 3x6x1mm 903306 sfh m3x6 903306 sfh m3x6 note orientation note orientation eccentric bushings have two different offsets from the center middle position = 0.5 mm or 0.5° from center outer position = 1mm or 1° from center the xray rear a...
Page 15
15 903306 sfh m3x6 303129 shim 3x6x1 toe-in track-width wheelbase roll center anti-dive kick-up all possible mounting alternatives of eccentric bushings eccentric bushings have two different offsets from the center. Middle position = 0.5 mm or 0.5° from center outer position = 1mm or 1° from center ...
Page 16
16 front toe-in bag 2x l=r oil 940508 bb 5x8x2.5 930306 bb 3x6x2.5 903308 sfh m3x8 2x l=r 303129 shim 3x6x1 3x1mm & 1x2mm composite shims approximately 47mm use bearing oil for all bearings note orientation 6mm thread note orientation note orientation tighten the screws gently but fully, and then lo...
Page 17
17 902305 sh m3x5 902306 sh m3x6 303129 shim 3x6x2 303126-k shim 3x6x5 303122-o shim 3x6x1 903306 sfh m3x6 chassis flex setting top deck setting h = hitec (24t) f = futaba, robe (25t) k = ko, jr, airtronics, sanwa (23t) optional alu top deck mount improves forward and rear traction and makes the car...
Page 18
18 05 bag 901304 362650 302663 303803 302804 930407 303212 980210 305341 302663 303432-o 303455 362650 302663 901303 302663 303212 305350-k 302253 305346 305394 305221 305328 362652 303123-k 302291 901304 362651 303127-k 303354 940510 303455 901303 303432-o 930407 307221 303129 362651 305350-k 90130...
Page 19
19 901302 sb m3x2.5 305392 p 2x10 305394 p 2x9 902205 sh m2x5 940510 bb 5x10x4 980210 p 2x10 rear toe-in track-width use alu 50mm drive shafts in rear use alu 50mm drive shafts in rear oil oil bearing oil (hudy #106230) bearing oil (hudy #106230) thread lock thread lock thread lock graphite grease (...
Page 20
20 902205 sh m2x5 940510 bb 5x10x4 980210 p 2x10 camber adjustment caster adjustment rear toe-in track-width 902310 sh m3x10 included included included included 55.5mm 53.5mm l=r l=r c-hubs front transmission #302334 alu 0° - r+l #302335 alu 2° - right #302336 alu 2° - left #302337 alu 4° - right #3...
Page 21
21 roll center camber 901304 sb m3x4 901304 sb m3x4 303122-k shim 3x6x1 303122-k shim 3x6x1 303127-k shim 3x6x4 303129 shim 3x6x1 alu shim 3x6x1mm alu shim 3x6x1mm left upright = right upright l=r 5mm thread 5mm thread 8mm thread 8mm thread l=r l=r initial setting rear transmission l=r alternative s...
Page 22
22 active toe-in 901304 sb m3x4 303123-k shim 3x6x2 303129 shim 3x6x1 903306 sfh m3x6 roll-center alu shim 3x6x2mm alu shim 3x6x2mm 5mm thread 10mm thread tighten gently rear transmission front transmission l=r l=r l=r alternative active rear suspension™ step 2 2x 2x ars linkage initial setting init...
Page 23
23 303129 shim 3x6x1 930407 bb 4x7x2.5 ackermann bumpsteer 8mm thread front transmission l=r l=r recommended bumpsteer settings: carpet - 1mm thick shim asphalt - 3mm thick shims the number of shims changes the angles of the steering linkage. When no shims are used, the car is easy to drive into the...
Page 24
24 901303 sb m3x3 901304 sb m3x4 anti-roll bars front anti-roll bar front anti-roll bar when the bars are set, verify that both sides move at the same time. If they do, the bars are set up correctly. If not, make sure that both downstops are the same and that the bar wire is flat. If the sides still...
Page 25
25 901303 sb m3x3 901304 sb m3x4 anti-roll bars rear anti-roll bar rear anti-roll bar active rear suspension™ standard suspension if the sides still do not move at the same time, adjust the length of the bar holders. Set the bar into the center, remove the play in the bushings, and tighten the setsc...
Page 26
26 30 3241 ball universal 5.8 mm hex (4) 30 8037 composite pistons 4-hole 1.0-1.2mm, 3-hole 1.0-1.2mm 30 8043-o ulp alu shock adjustable nut - orange (2) 30 8082 t4 shock absorber membrane (4) 30 8092 t4 shock foam inserts (4) 30 8308-o ulp alu shock absorber-set - orange (2) 30 8316 shock ball join...
Page 27
27 970131 o 13x1.0 972030 o 3x2 hint: pre-thread the ball joint using an m3 screw. Warning! Be careful not to pre-thread too far, since the ball joint may split or the plastic threads may strip out. Incorrect fully extend the piston rod so the piston is at the bottom of the shock body. Hold the shoc...
Page 28
28 shock damping spring rate selection shock damping release 2-3 turns tighten fully 0% 50% 75% rebound adjustment rebound check ➊ ➋ ➌ 100% 25% after the shock is assembled you have to set the shock rebound: ➊ release the shock cap by 2-3 turns. ➋ push the shock shaft fully up. For the first time th...
Page 29
29 903308 sfh m3x8 903310 sfh m3x10 960030 n m3 bag 07 30 1202 composite bumper 30 1216 composite bumper upper holder brace 30 1218 composite upper holder for bumper 30 1322 front body mount set 30 1325 t4 composite brace for bumper - low (2) 30 3129 composite set of wheelbase shims (3x1mm; 1x2mm) (...
Page 30
30 shock position ride height droop 981212 p 2x12 l=r 3x6x2mm 303129 shim 3x6x2 902308 sh m3x8 902312 sh m3x12 front shock spring c=2.5 7. Front & rear assembly l=r #301228 t4 foam bumper wide - hard #301351-o alu adjustable body post stop (2) #302085 t4 shock tower front 3.0mm graphite #308307-o xr...
Page 31
31 shock position ride height droop bag 07 981212 p 2x12 902308 sh m3x8 902308 sh m3x8 306219 shim 3x6x2 306219 shim 3x6x3 l=r 308308-o 902308 306219 981212 902308 301332 301332 306219 3x6x2mm 3x6x1mm 30 1332 rear body mount set 30 6219 composite set of servo shims (4) 90 2308 hex screw sh m3x8 (10)...
Page 32
32 bag 902308 sh m3x8 903306 sfh m3x6 306219 shim 3x6x1 306219 shim 3x6x2 306219 shim 3x6x3 07 add shims between servo and alu servo mounts in case you want to move the servo (weight) more forward. There are 3 different thickness of shims. View 1mm 2mm 3mm minimum space 0.5mm servo screw (not includ...
Page 33
33 903306 sfh m3x6 the inline chassis flex adjustment has a direct effect on the steering characteristics of the car. The more stiff the inline chassis flex is, better steering response and more in-corner steering is generated. Attach the graphite reinforcement plate from the top so the chassis stay...
Page 34
34 gearing adjustment 902308 sh m3x8 903308 sfh m3x8 #303061 graphite motor guard adjust the motor so the pinion meshes with the spur gear properly. Make sure the gear mesh is not too tight. There should be a small amount of play between the teeth of the pinion gear and the spur gear. Detail #306410...
Page 35
35 960140 n m4 903306 sfh m3x6 detail 4x #306186 alu lipo battery backstops (f+r) 7. Final assembly make sure the wheel nuts are very tight, so the wheels do not loosen during operation. Lipo battery pack (not included) we recommend using #107870 hudy fibre reinforced tape (not included) #306165 gra...
Page 36
/teamxray /teamxray /teamxray /xrayracing /teamxrayrc /xrayracing rc america, 2030 century center blvd #15, irving, tx 75062, usa phone: 214-744-2400, fax: 214-744-2401, xray@rcamerica.Com.