Operation manual x-hw13008gen x-hw33008gen hot water pressure washer.
2 table of contents.
3 table of contents safety 6 safety rules 7 safety warnings features 13 features - small frame 15 features - large frame installation & preparation 17 attire 17 set-up 18 power cord connection 20 burner fuel tank 20 adjustable pressure dual lance 21 water supply 22 unloader 22 thermal relief valve 2...
4 using the operator’s manual the operating manual is an important part of your pressure washer and should be read thoroughly before initial use, and referred to often to make sure adequate safety and service concerns are being addressed. Reading the owner’s manual thoroughly will help avoid any per...
5 product identification record identification numbers pressure washer if you need to contact an authorized dealer or customer service line (1- 866-770-1711) for information on servicing, always provide the product model and identification numbers. You will need to locate the model and serial number...
6 safety the safety alert symbol ( ) is used with a signal word (danger, caution, warning), a pictorial and/or a safety message to alert you to hazards. Danger indicates a hazard which, if not avoided, will result in death or serious injury. Warning indicates a hazard which, if not avoided, could re...
7 safety warning serious injury or death could occur if the pressure washer is not properly grounded. Your pressure washer is powered by electricity and may cause electric shock or electrocution if not used properly. Electrical shock may occur from electrical cord. Electrical shock may occur if pres...
8 warning serious injury or death may occur from normal sparks in the multiple ignition sources or burner exhaust. Injury or death may occur as a result of improper fueling. Serious injury or death may occur if system safety’s are not properly maintained. • always operate pressure washer in a well v...
9 safety warning serious injury or death may occur from inhaling burner exhaust or dangerous vapors. • never operate this pressure washer in an enclosed area. Always make certain there is adequate ventilation (fresh outside air) for breathing and combustion. This will prevent the buildup of dangerou...
10 safety warning serious injury may occur from a pressure washer malfunction or exploding accessories if incorrect system components, attachments or accessories are used. Serious injury or death may occur if attempting to start the pressure washer when the pumping system is frozen. • never make adj...
11 safety warning serious injury or death may occur from detergents con- tacting the skin. Serious injury can occur from loose debris being pro- pelled at a high speed from the spray gun. Injury may occur if the operator loses his balance caused by the thrust of water traveling through the spray noz...
12 safety • know how to stop the pressure washer and bleed pressures quickly. Be thoroughly familiar with controls. • do not leave pressurized unit unattended. Shut off the pressure washer and release trapped pressure before leaving. • do not operate the unit if you see any fuel, oil or water leaks ...
13 features 8 operator's manual 0m hse00 gen -032905-rz hse-small frame features features - small frame.
14 1. Pneumatic wheels 2. Protective rollcage 3. Control panel 4. Decal-warning/caution/operation 5. Switch-off/pump/burner (steam optional) 6. Center balanced lifting eye 7. Convenient push/pull handle 8. Decal-warning: hot 9. Heat exchanger exhaust 10. Wand holder 11. Water inlet 12. Water straine...
15 features 0 operator's manual 0m hse0 5 gen -032905-rz hse-large frame features features - large frame 1. Decal- warning: risk of explosion 2. Coil drain 3. High pressure outlet 4. Data plate 5. Burner air regulation 6. Brake 7. Burner fuel tank 8. Pnuematic wheels 9. Pressure switch 10. High pres...
16 body/frame: one piece, welded construction, full roll cage with solid steel axles, lifting hook and convenient push/pull handle. Portability: four pneumatic four-ply tires for easy mobility. Finish: powder coated high pressure hose: 3/8” x 50’ trigger gun assembly: trigger controlled, safety lock...
17 installation & preparation attire proper attire is essential to your safety. It is advised to utilize whatever means necessary to protect eyes, ears, and skin. Additional safety attire (such as respiratory mask) may be required when using detergent cleaning agents with this washer. Set-up 1. This...
18 installation & preparation power cord connection 1. Make certain the motor switch is in the “off” position. 2. Ensure electrical supply is identical to the specifications listed on the pressure washer data plate. 3. Grounding instructions: this product must be grounded. If it should malfunction o...
19 warning to reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch plug with wet hands. 6. Extension cords:the manufacturer does not recommend the use of extension cords! If use of an extension cord is unavoidable, it must be plugged into a gfci found in circui...
20 danger do not smoke while fueling! Do not fill the fuel tank while unit is running or hot. Allow unit to cool for two minutes before re-fueling. Do not fill fuel tank to point of overflowing. Allow approximately 1/4” of tank space for fuel expansion. Always store fuel away from the washer while t...
21 water supply 1. Select a water supply hose which is a quality grade of garden hose measuring at least 3/4” id and no longer than 50 feet. 2. If your unit is equipped with a water strainer, ensure it is clean and free of any obstructions. Periodic cleaning of the water strainer will help prevent p...
22 unloader thermal relief valve pre-start inspection procedures standard models: the unloader has been preset at the factory. Steam option models: the unloader has an adjustment knob which has a minimum/maximum setting. Move the unloader clockwise to the maximum setting for cold/hot water operation...
23 operation operating instructions flushing the system this unit has a steel coil which, after setting, will cause the water remain- ing in the coil from the previous usage to turn brown or black. This water must be flushed from the system before start-up. This procedure should be performed without...
24 operation 1. Refer to the “safety precautions” pgs. 7-12 before starting the unit. 2. Locate the safety decals on your unit and heed their warnings. 3. Ensure that the switch is in the “off” position. 4. Pointing the trigger gun in a safe direction, unlock the trigger gun and squeeze the trigger....
25 operation hot water operation warning the water temperature could become very hot during hot water operation. Be cautious when adjusting pressure or controlling the trigger gun/ lance assembly. 1. Follow the steps 1-8 outlined for “start-up/cold water operation”. 2. Move the switch to the “burner...
26 1. Refer to “risk of bodily injury / detergents” pg. 11. Be certain to wear protective safety attire as stated on pg. 17. 2. Prepare detergent solution according to label directions. (never pump acids, alkalines, abrasive fluids or solvents through the unit. Due to the unknown and often corrosive...
27 notice this injection system is designed to apply detergents under low pres- sure only. It will not allow detergent solutions to be introduced into the system unless the adjustable nozzle is set in the low pressure mode. Operation 5. To apply solution; unlock the trigger gun and squeeze the trigg...
28 maintenance storage & maintenance instructions specific maintenance pump: change the pump oil after the first 50 hours of operation. After initial change, every 3 months or 250 hour intervals are recommended. If oil appears dirty or milky, changes may be required in greater frequency. Use pump oi...
29 notice if using teflon tape, be certain no tape gets inside any plumbing to prevent the possibility of a plugged spray nozzle. Maintenance 5. Dispose of drainage according to environmental regulations in your area. Burner air adjustment: the air shutter has been factory preset for proper operatio...
30 notice proper winterizing is based on the recommended manufacturer’s instructions listed on the “protection chart” shown on the back label of most antifreeze containers. Winterizing 1. For storage and transportation purposes in subfreezing ambient tem- peratures, it will be necessary to winterize...
31 6. With the trigger gun held open, siphon enough water out of the 5 gallon container until there is just enough water left to mix with the antifreeze. 7. Point the trigger gun into the empty container. (be certain to wear safety attire for protection from splashing.) 8. Trigger the gun until the ...
32 maintenance notice when using this procedure, use caution as ice chips can form from drops of water which could cause the unit to burst if starting before completely thawed. 20 20 operator's manual d. Remove the coil drain plug from the heat exchanger inlet. E. Start the unit and allow it to run ...
33 maintenance chart procedure daily 3 months 6 months 9 months 12 months inspect electrical cord x test gfci x test voltage and amp draw x check water pump oil level x change water pump oil ** x x x x oil leak inspection x fuel leak inspection x water leak inspection x hose inspection x water inlet...
34 troubleshooting troubleshooting troubleshooting chart symptom probable cause remedy pump motor will not run. Circuit overload. Check wall breaker or fuse. Gfci tripped. Reset. Motor overload. Reset thermal overload button on pump motor or inside electrical control panel. Auto start/stop option in...
35 troubleshooting symptom probable cause remedy oil leaking from unit. Worn seals or o-rings. Contact customer service. Detergent will not siphon . Detergent strainer is not completely submerged in detergent solution. Check, submerge if necessary. Detergent strainer obstructed. Inspect, clean or re...
36 symptom probable cause remedy burner will not ignite steam option: cad cell option: trigger gun is closed. Open trigger gun for pressure. Pressure switch override. Pressure should be over 250 psi to allow burner to come on. High limit switch override. Unit will automatically reignite when cool. F...
37 symptom probable cause remedy burner runs erratically. Water in the fuel oil. Drain fuel filter/water separator. Drain fuel tank, and replace with clean fuel. Dirty fuel filter/water separator. Replace element. Dirty fuel nozzle. Replace. Fuel pickup screen obstructed. Consult customer service. I...
38 statement of warranty warranty the manufacturer warrants all parts, (except those referred to below), of your new pressure washer to be free from defects in materials and work- manship during the following periods: for lifetime against freezing and cracking: pump manifold for seven (7) years from...
39 1. The motor is covered under separate warranty by its respective manufacturer and is subject to the terms set forth therein. 2. Normal wear parts: pump packings spray nozzles pump valves detergent valves fuel filters quick couplers/screw connects o-rings belts 3. This warranty does not cover par...
40 if you need assistance with the assembly or operation of this pressure washer please call 1-866-770-1711.