XtendLan XL-DSPL7-5 User Manual

Manual is about: ultra-slim 7 inch digital signage

Page of 10

Download

Print this page

Bookmark us

FCC Notices

XL-DSPL7-5

User Manual

’s herewith confirmed to comply with the requirements of FCC Part 15 Rules. Operation is

subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may

cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

residential installation. This equipment generated uses and can radiate radio frequency

energy and if not installed and used in accordance with the instruction manual may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio of television reception, which can be determined by turning the

equipment off or on, the user is encouraged to try to correct the interference by one or more

of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio TV technician for help.

1 2 3 4 5 6 7 Next › »

Summary of XL-DSPL7-5

Page 1
1 fcc notices xl-dspl7-5 user manual it ’s herewith confirmed to comply with the requirements of fcc part 15 rules. Operation is subject to the following two conditions: * this device may not cause harmful interference. * this device must accept any interference received, including interference that...
Page 2
2 3 1. Package contents ……………………..……………………….. 3 2. Introducti on……………………………….……………………... 3 3. Feature s………………………………………….……………… 3 4. Hardware overview …………………..………………………... 4 4.1 timer ’s battery installation….…....….……………………. 5 5. Remote control …………………………..…………………….. 6 6. Start the xl-dspl7-5.. ………...
Page 3
4 5 4. Hardware overview 4.1 timer ’s battery installation step1. Remove the battery cover screw, and then slide off the battery cover. Step2. Insert the battery (cr1220 3v) with correct polarity (+/-), and then close the battery cover, and fasten it with the screw..
Page 4
6 7 5. Remote control 6. Start the xl-dspl7-5 1 power on/ off 2 no function 3 open the setup menu 4 memory card selection 5 mute sound 6 move the cursor 7 confirm the selection/ entry 8 open the timer setup window 9 volume up/ down 10 list all the pictures. 11 list all the music 12 list all the vide...
Page 5
8 9 ▲ ▼ 7. Setting up □ auto start: enable/ disable the auto play function after power on. - off: disable the auto start function - all: play all media files on the memory card after power on. □ in the main menu, using the “▲、▼、、 ” button on remote control to select the “setup” item, - photo + musi...
Page 6
10 11 7.2 photo setup □ slideshow mode: enable/ disable the slideshow function. □ interval time: set the time each photo is shown to 1, 3, 5, 10, 30 or 60 seconds. □ transition mode: set transition effects between photos. 7.3 firmware setup □ firmware version: display the current firmware version. 8...
Page 7
12 13 8.1.2 media files production describe with the version of 6 division buttons. The version of 6 division buttons supports 2 kinds of templates. Template 1 template 2 step1: create 6 media files (layer 2), and name the files “001.Xxx” ~ “006.Xxx” (xxx is a file extension). Step2: using the movie...
Page 8
14 15 ▲ ▼ 8.2 usb auto-copy function step1: use the “notepad” to create a file on your pc. Type “autocopy” and named the file “autocopy.Ini” . Autocopy.Ini step2: put the files that you want to copy and the file “autocopy.Ini” to the usb pen driver. Note: 1. If the file “autocopy.Ini” is not on pen ...
Page 9
16 17 ▲ ▼ ▲ 8.4 programmed play function step1: confirm the programmed play function is enabled. Preferences > → auto start > → programmed play > please restart the xl-dspl7-5 after setting, and the xl-dspl7-5 will play the file automatically. Step2: press the “stop” button to stop playing, and the ...
Page 10
18 9. Troubleshooting situation check point no picture 1. Check power cable and power switches. 2. Make sure the file format on the memory card is correct. No response from the remote control 1. Ensure that the battery (cr2025 3v lithium battery) in the remote control and it is inserted the correctl...