DL manuals
Yaesu
Processor
FT-2000D - UPDATE V0151 AND V11.54 INFORMATION
Update Manual

Yaesu FT-2000D - UPDATE V0151 AND V11.54 INFORMATION Update Manual

Page of 8

Download

Print this page

Bookmark us

4/23/10

PEP2000

This procedure is used to update Main CPU Ver.

0151

and EDSP Ver.

11.54

the

flash programming for the FT-2000/D Transceivers.

We recommend installing the Flash Programming Software on a PC computer with Windows 2000,

XP or Vista Operating System; and use the CT-119 programming cable or 8-pin mini-DIN PGM-SW

(P0091526) and serial cable RS-232C, DB9F to DB9F straight cable.

NOTE: There are many USB adapters available; however some may not function with this software.

We recommend using the latest USB adapter driver software when available.

If the CT-119 programming cable or is not available you will need a RS-232C, DB9F to DB9F

straight cable and 8pin mini-DIN PGM-SW (P0091526). If the DIN PGM-SW is not available you

will need to operate the internal program switch S3004. Please follow the instructions in

ADDENDUM: Page 7 and 9.

The software versions can be displayed on the radio

While holding the three buttons [GEN]＋[50]＋[ENT] turn the radio on. The software version will be

displayed in the VFO-A window for 5 seconds then the radio will start up in normal operation.

See below:

Example EDSP V11.53 and MAIN V0150 software version.

*If you already have

EDSP

V11.54

and MAIN

V0151

software versions,

it is not necessary to update the FT-

2000/D again.

The software updates will work with all versions (AF, AS, EU, NA, OC, SA or all Countries) of the

FT-2000 and FT-2000D.

The update software is available from our website at

http://www.yaesu.com

. The CT-119

programming cable is available from your authorized Vertex Standard dealer. You may also order

by email to Vertex Standard parts department,

yaesuparts@vxstdusa.com

Main CPU:

Software version

(This image & version is for

illustration only)

EDSP:

Software version

11.XX

(This image & version is for

illustration only)

1 2 3 4 5 6 7 Next › »

Summary of FT-2000D - UPDATE V0151 AND V11.54 INFORMATION

Page 1
4/23/10 pep2000 this procedure is used to update main cpu ver. 0151 and edsp ver. 11.54 the flash programming for the ft-2000/d transceivers. We recommend installing the flash programming software on a pc computer with windows 2000, xp or vista operating system; and use the ct-119 programming cable ...
Page 2
Ver. 0151 main cpu implements improvements (also includes all previous updates): • agc: corrected the agc in the “off” position; if an agc menu set item was changed, the agc would sometimes turn “on”. • keyer: the extraneous “dot” memory is eliminated during rapid keying when the dash output starts....
Page 3
(2) connect the ct-119 cable’s db9f connector to the serial port com1 in the back of your computer. If you use a usb to serial adapter, you might need to change the com port number. (3) now go to the desktop open pep2000_main folder and find the fsw003 icon as shown below. Double-clickthe fsw003icon...
Page 4
Edsp edsp software update this procedure is used for uploading new edsp software into the ft-2000/d amateur transceivers, from your personal computer, using the rs-232c, db9f to db9f straight cable. 1. Turn off the main power switch located on the back of the ft-2000 (or turn off the power supply fo...
Page 5
6. Click the update button. You will see ah025h_v1154 out file displayed. If you do not see ah025h_v1154 (as in the screen below), then open the “look in:” window and go to the desktop and find pep2000_edsp. Open the folder and ah025h_v1154 will be displayed in the window. Click ah025h_v1154 out fil...
Page 6
Addendum if the ct-119 programming cable or 8-pin mini-din pgm-sw (p0091526) is not available you will need a serial cable rs-232c, db9f to db9f straight cable. Please follow these instructions. Main software update *don't forget to write down (or save to a cf card) any personal menu settings you ha...
Page 7
(7) now go to the desktop open pep2000_main folder and find the fsw003 icon as shown below. Double-clickthe fsw003icon, displayed on the program screen. (8) when the program opens, confirm that the file ah025_v0151.Sfl is highlighted; if not, click on it to highlight it (9) click on [write] in the p...
Page 8
Figure a remove the left rear foot (near the cat connector) to expose the program switch access hole. Switch s3004 is visible through the hole. Move the switch to the on (rear) position. (top of picture) this is just a screw hole for reference ..