- DL manuals
- Yaesu
- Transceiver
- FT-450D
- Operation Manual
Yaesu FT-450D Operation Manual - page 30
Page 28
FT-450D O
PERATION
M
ANUAL
IF
BANDWIDTH
IF
BANDWIDTH
IF
BANDWIDTH
CONTOUR (I
NTERFERENCE
R
EJECTION “S
IGNALS
WITHIN
3
KHZ
”
)
The Contour filtering system provides a gentle perturbation of the IF filter pass band, so as to suppress or
enhance particular frequency components in five steps, thus improving the sound and/or readability of a re-
ceived signal.
1. Press the [DSP] button several times to set the
“>” icon to the “CONTOUR” indicator of the DSP
Graphic Display on the display.
2. Press the [DSP/SEL] knob to engage the con-
tour filter.
3. Press and hold the [DSP/SEL] knob for one sec-
ond to toggle the contour filter’s level between
“null” and “peak”.
4. Rotate the [DSP/SEL] knob to achieve the most
natural-sounding audio reproduction on the in-
coming signal.
The peak position of the contour filter is graphi-
cally-depicted in the “CONTOUR” indicator of the
DSP Graphic Display on the LCD.
5. Press the [DSP/SEL] knob again to increase the
contour filter’s level (“null” or “peak”).
6. To disable the contour filter, press the [DSP/SEL]
button again. The graphic disappears from the
“CONTOUR” indicator of the LCD Display, confirm-
ing that the contour filter is no longer operating.
Q
UICK
P
OINT
:
The steep slopes of the DSP filtering can, when adjusted aggressively, impart an unnatural sound to an incom-
ing signal. Often, a narrow bandwidth is not the key to improving copy. The incoming signal itself may have
undesirable or excessive frequency components. By judicious use of the Contour filter, the “shoulder” of the
passband response may be altered, or components removed from within the passband, allowing the desired
signal to rise above the background noise and interference in a manner not obtainable with other filtering sys-
tems.
C
ONVENIENCE
F
EATURES
“CONTOUR” Indicator
[DSP] button
[DSP/SEL] knob
C
ONTOUR
G
AIN
“H
IGH
”
C
ONTOUR
“N
ULL
”
C
ONTOUR
“P
EAK
”
C
ONTOUR
“O
FF
”
C
ONTOUR
G
AIN
“L
OW
”
C
ONTOUR
“N
ULL
”
C
ONTOUR
“P
EAK
”
C
ONTOUR
“O
FF
”
Refer to Figure “B”, this shows a “indenta-
tion” of the contour filter is center of a pass-
band. Counter-clockwise rotation (to the left)
of the [DSP/SEL] knob causes the indenta-
tion to move toward a lower frequency within
the passband, while clockwise rotation (to the
right) causes the indentation to move toward
a higher frequency within the passband. By
removing interference or unwanted frequency
components on the incoming signal, it is pos-
sible to make the desired signal rise out of
the background noise/interference, enhanc-
ing intelligibility.
A B C
Summary of FT-450D
Page 1
Hf/50 mh z t ransceiver ft-450d o peration m anual vertex standard co., ltd. 4-8-8 nakameguro, meguro-ku, tokyo 153-8644, japan vertex standard us headquarters 10900 walker street, cypress, ca 90630, u.S.A. Yaesu uk ltd. Unit 12, sun valley business park, winnall close winchester, hampshire, so23 0l...
Page 2
General feature ........................................... 1 front panel buttons and knobs ............ 2 display indications ....................................... 6 rear panel jacks .......................................... 8 supplied mh-31 a8j microphone ................. 9 accessories & optio...
Page 3
Page 1 ft-450d o peration m anual t able of c ontents rtty (radio teletype) operation .......... 74 setting up for rtty operation .......................... 74 basic setup ................................................................. 74 packet operation ....................................... 75...
Page 4
Page 2 ft-450d o peration m anual phones key f ront p anel b uttons and k nobs phone jack a 3.5 mm, 3-contact jack accepts ei- ther monaural or stereo headphones with 2 or 3-contact plugs. When a plug is inserted, the loudspeaker is dis- abled. N ote : when wearing headphones, we rec- ommend that yo...
Page 5
Page 3 ft-450d o peration m anual f ront p anel b uttons and k nobs c.S/voice button press this button to activate one of the 52 functions, which can be assigned via menu item “pnl-c.S.” press the [f] button followed by this button to announce the current operating frequency (with resolution to the ...
Page 6
Page 4 ft-450d o peration m anual phones key f ront p anel b uttons and k nobs clar button pressing this button activates the clarifier, to allow temporarily offsetting the receive frequency. When the clarifier is active, you may offset the receive frequency by adjust- ing the [main dial] knob. Shif...
Page 7
Page 5 ft-450d o peration m anual f ront p anel b uttons and k nobs a=b button press this button momentarily to transfer data from vfo-a fre- quency (or a recalled memory channel) to vfo-b, overwriting the previous contents in vfo-b. Use this key to set both vfo-a and vfo-b to the same frequency and...
Page 8
Page 6 ft-450d o peration m anual phones key d isplay i ndications dsp graphic display : the peak position of the contour filter is depicted graphically here when the contour filter is activated. : the null position of the if notch filter is depicted graphically here when the if notch filter is acti...
Page 9
Page 7 ft-450d o peration m anual d isplay i ndications frequency display the operating frequency is displayed. : this indicator appears during transmission. : this indicator appears whenever the receiver squelch is open. : this indicator appears when the internal automatic antenna tuner is activate...
Page 10
Page 8 ft-450d o peration m anual r ear p anel j acks input dc 13.8v 22a ant gnd ext spkr cat linear tuner data dc in jack this is the dc power supply connection for the transceiver. Use the supplied dc cable to connect directly to the car bat- tery or to a dc power supply, which must be capable of ...
Page 11
Page 9 ft-450d o peration m anual dynamic microphone mh-31 dwn fst up s upplied mh-31 a8j m icrophone ptt switch press this switch to transmit, and release it to receive after your transmission is com- pleted. Mic the microphone is located here. Speak into the micro- phone in a normal voice level. T...
Page 12
Page 10 ft-450d o peration m anual a ccessories & o ptions s upplied a ccessories hand microphone (mh-31 a8j ) 1 pc p/n: m3090086a dc power cord with fuse 1 pc p/n: t9025225 fuse 1 pc p/n: q0000074 operation manual 1 pc warranty card 1 pc a vailable o ptions external automatic antenna tuner (for wir...
Page 13
Page 11 ft-450d o peration m anual i nstallation c onnection of a ntenna and p ower s upply the ft-450d is designed for use with any antenna system providing a 50 ohm resistive impedance at the desired operating frequency. Every effort should be made to ensure the impedance of the antenna system is ...
Page 14
Page 12 ft-450d o peration m anual i nstallation a bout c oaxial c able use high-quality 50-ohm coaxial cable for the lead-in to your ft-450d transceiver. All efforts at providing an efficient antenna system will be wasted if poor quality, lossy coaxial cable is used. This transceiver utilizes stand...
Page 15
Page 13 ft-450d o peration m anual input dc 13.8v 22a ant gnd ext spkr cat linear tuner data ant 1 ant 2 ant 3 ant 4 remote on off band data 1 band data 2 gnd alc 2 alc 1 ptt 2 ptt 1 input 1 input 2 control dc48v in a n t in p u t d c 1 3. 8 v a n t 1 h f ve rt ic al a nt en na h f d ip ol e a nt en...
Page 16
Page 14 ft-450d o peration m anual phones key e asy o peration r eceiving 1. Connect your antenna to the ant jack on the rear panel. 2. Connect the after-market dc power supply (or car battery) using the supplied dc power cable, and set the power switch of the dc power supply to on. 3. Press and hol...
Page 17
Page 15 ft-450d o peration m anual [f] button [dsp/sel] knob h ow to use the [dsp/sel] knob e asy o peration when a dsp function is not selected and no “>” icon is shown in the lcd graphic display, then turning the [dsp/sel] knob controls the frequency in vfo mode, or selects the memory channel in m...
Page 18
Page 16 ft-450d o peration m anual h ow to use the [c.S/voice] s witch you may set the [c.S/voice] button function to one of 52 functions via menu item “pnl-c.S”. To assign a function to the [c.S/voice] button: 1. Press and hold the [f] button for one second to enter the menu mode. The “ ” icon will...
Page 19
Page 17 ft-450d o peration m anual k ey d uration s etting the duration that buttons are held determines the function they activate. Factory default is one second. Pressing a button for less than one second activates one function. Pressing and holding the button in for longer than one second activat...
Page 20
Page 18 ft-450d o peration m anual r esetting the m icroprocessor the ft-450d has three reset methods. E asy o peration vfo/m emory r eset use this procedure to reset (clear out) the memory channels (except the qmb channel) previously stored and vfo data, without affecting any configuration changes ...
Page 21
Page 19 ft-450d o peration m anual t uning s teps r eceiving the tuning step of the [main dial] knob and the [dsp/sel] knob is different depending on the oper- ating mode. 1: when you press the [dsp/sel] knob, the tuning step of the [dsp/sel] knob changes to 100 khz in all modes. 2: in the factory d...
Page 22
Page 20 ft-450d o peration m anual r eceiving a bout the [up]/[dwn] buttons of the mh-31 a8j the microphone [up]/[dwn] keys utilize the tun- ing steps of the [main dial] knob on the ssb/ cw/data mode, and utilize the tuning steps of the [dsp/sel] knob on the am/fm mode. When the microphone [fst] key...
Page 23
Page 21 ft-450d o peration m anual r eceiving d igital v oice a nnouncement press the [f] button followed by the [c.S/voice] but- ton to announce the current operating frequency (with resolution to the displayed 100 hz digit) and operat- ing mode. A dvice : if you assign the “voice2” function to the...
Page 24
Page 22 ft-450d o peration m anual m y b ands o peration the “my bands” feature allows you to select several amateur bands, and make only those bands available for selection via the [band ]/[band] buttons. This feature can be very useful in a contest, where the 10/18/24 mhz band are not used, or if ...
Page 25
Page 23 ft-450d o peration m anual m y m odes o peration the “my modes” feature allows you to select the operating modes you wish to have available for selection via the [mode ]/[mode] buttons. Only the desired modes will be displayed in the loop. This feature can be very useful in an hf operation, ...
Page 26
Page 24 ft-450d o peration m anual d igital v oice r ecorder p reparations 1. Press and hold the [f] button for one second to enter the menu mode. The “ ” icon will ap- pear on the display. 2. Rotate the [dsp/sel] knob to select the menu item “pnl-c.S”. 3. Press the [dsp/sel] knob to enable adjustme...
Page 27
Page 25 ft-450d o peration m anual r eceiver o peration (f ront e nd b lock d iagram ) the ft-450d includes a wide range of special features to suppress the many types of interference that may be encountered on the hf bands. However, real world interference conditions are constantly changing, so opt...
Page 28
Page 26 ft-450d o peration m anual n oise b lanker (i nterference r ejection “s ignals within 3 khz ” ) the ft-450d includes an effective noise blanker, which can significantly reduce noise caused by automotive ignition systems. Ipo/att (a djust the r eceiving s ensitivity ) you may reduce the recei...
Page 29
Page 27 ft-450d o peration m anual agc (t ool for c omfortable and effective r eception ) the agc system is designed to help compensate for fading and other propagation effects, with characteristics that can be of particular value on each operating mode. The basic objective of agc is to maintain a c...
Page 30
Page 28 ft-450d o peration m anual if bandwidth if bandwidth if bandwidth contour (i nterference r ejection “s ignals within 3 khz ” ) the contour filtering system provides a gentle perturbation of the if filter pass band, so as to suppress or enhance particular frequency components in five steps, t...
Page 31
Page 29 ft-450d o peration m anual shift (i nterference r ejection “s ignals within 3 khz ” ) if shift allows you to vary the dsp filter passband higher or lower, without changing the pitch of the incoming signal, so as to reduce or eliminate interference. Because the carrier tuning frequency is not...
Page 32
Page 30 ft-450d o peration m anual referring to figure “b”, this is default band- width. By rotating the [dsp/sel] knob to the left, the bandwidth will narrow (see figure “a”), while rotation of the [dsp/sel] knob to the right, as depicted in figure “c”, will widen the bandwidth. The default bandwid...
Page 33
Page 31 ft-450d o peration m anual c onvenience f eatures notch (i nterference r ejection “s ignals within 3 khz ” ) the if notch filter is a highly effective system that allows you to slice out an interfering beat note or other carrier signal from inside the receiver passband. “notch” indicator [ds...
Page 34
Page 32 ft-450d o peration m anual “dnr” indicator [dsp] button [dsp/sel] knob dnr (i nterference r ejection “s ignals within 3 khz ” ) the digital noise reduction (dnr) system is designed to reduce the level of random noise found on the hf and 50 mhz bands, and it is especially effective during ssb...
Page 35
Page 33 ft-450d o peration m anual rf gain the rf gain controls provide manual adjustment of the gain levels for the receiver rf and if stages, to com- pensate for noise and/or signal strength conditions at the moment. The [sql/rf gain] knob should, initially, be rotated to the fully clockwise posit...
Page 36
Page 34 ft-450d o peration m anual u sing the a utomatic a ntenna t uner the automatic antenna tuner (hereinafter referred to as the “atu”) built into each ft-450d is designed to ensure a 50-ohm load for the final amplifier stage of the transmitter. We recommend that the atu be used whenever you ope...
Page 37
Page 35 ft-450d o peration m anual u sing the a utomatic a ntenna t uner a bout atu o peration figure 1 depicts a situation where normal tuning via the atu has been successfully completed, and the tuning data has been stored in the atu memory. The antenna system as seen by the transmitter is shown. ...
Page 38
Page 36 ft-450d o peration m anual phones key 1. Press the [band ]/[band] buttons to select the operating band. By pressing the [band ]/[band] buttons, the operating band will change as follows. 7 10 14 15 18 21 24.5 28 50 1.8 3.5 7 ...... 2. Press the [mode ]/[mode] buttons to select the lsb, usb o...
Page 39
Page 37 ft-450d o peration m anual ssb/am m ode t ransmission tx m eter s election you may change the po meter function to alc meter or swr meter in the transmit mode. Tx p ower a djustment by pressing the [meter/dim] button, the meter func- tion will change as follows. Po alc swr po ...... Po: indi...
Page 40
Page 38 ft-450d o peration m anual t ransmitter t ime -o ut t imer (tot) the “time-out timer” (tot) feature that is designed to force the transceiver into the “receive” mode after a preset time period of continuous transmission (the default is “off”). This feature prevents your transceiver from tran...
Page 41
Page 39 ft-450d o peration m anual m icrophone g ain l evel a djustment at the factory, a microphone gain has been programmed that should be satisfactory for the supplied mh-31 a8j hand microphone. If you use an after-market microphone, you may wish to set a different microphone gain level. 1. Press...
Page 42
Page 40 ft-450d o peration m anual dsp m icrophone e qualizer you may select one of ten available dsp equalization techniques for transmitted microphone audio. 1. Press and hold the [dsp] button for one second. This instantly activates menu item “mic eq”. The “ ” icon will appear on the display. 2. ...
Page 43
Page 41 ft-450d o peration m anual a utomatic tx/rx s witching using v oice c ontrol (vox) instead of using the microphone’s ptt switch to activate the transmitter, the vox (voice operated tx/rx control) system provides hands-free, automatic activation of the transmitter, based on voice input into t...
Page 44
Page 42 ft-450d o peration m anual ssb/am m ode t ransmission monitor you may listen to the quality of your transmitted signal using the monitor feature. P reparations assign the monitor feature to the [c.S/voice] button. 1. Press and hold the [f] button for one second to enter the menu mode. The “ ...
Page 45
Page 43 ft-450d o peration m anual ssb/am m ode t ransmission s plit -f requency o peration a powerful capability of the ft-450d is its flexibility in split frequency operation, using vfo-a and vfo-b frequency registers. This makes the ft-450d especially useful for high-level dx-pedition use, as the...
Page 46
Page 44 ft-450d o peration m anual ssb/am m ode t ransmission v oice m emory (ssb/am/fm m odes ) you may utilize the voice memory capability of the ft-450d for repetitive messages. The voice memory system includes two memories (vm1 and vm2) capable of storing up to 10 seconds of voice audio each. Th...
Page 47
Page 45 ft-450d o peration m anual ssb/am m ode t ransmission n ote.
Page 48
Page 46 ft-450d o peration m anual the powerful cw operating capabilities of the ft-450d include operation using both an electronic keyer paddle and a “straight key” or emulation thereof, as is provided by a computer-based keying device. S etup for s traight k ey ( and s traight k ey emulation ) o p...
Page 49
Page 47 ft-450d o peration m anual u sing the b uilt - in e lectronic k eyer before starting, connect your keyer paddle to the front panel key jack in the status that turned off the [power(on/ off)] switch. 1. Press the [band ]/[band] buttons to select the operating band. By pressing the [band ]/[ba...
Page 50
Page 48 ft-450d o peration m anual s etting the k eyer w eight (d ot /s pace :d ash ) r atio the menu item “cwweight” may be used to adjust the weight for the built-in electronic keyer. The default weighting is 3:1 (a dash is three times longer than a dot or space). 1. Press and hold the [f] button ...
Page 51
Page 49 ft-450d o peration m anual cw s potting (z ero -b eating ) “spotting” (zeroing in on another cw station) is a handy technique for ensuring that you and the other station are precisely on the same frequency. Cw m ode o peration t o u se cw s potting : in cw mode, while pressing and holding th...
Page 52
Page 50 ft-450d o peration m anual cw d elay t ime s etting during semi-break-in (not qsk) operation, the hang time of the transmitter, after you have finished sending, may be adjusted to a comfortable value consistent with your sending speed. This is the functional equivalent to the “vox delay” adj...
Page 53
Page 51 ft-450d o peration m anual cw p itch a djustment you may adjust the center frequency of the receiver passband, as well as the pitch of your offset cw carrier via the menu item “cwpitch”. Available tone selections are 400 hz through 800 hz, in 100 hz step. Cw m ode o peration 1. Press and hol...
Page 54
Page 52 ft-450d o peration m anual b eacon f eature the ft-450d’s unique “beacon” feature allows you to set up the transceiver to send a repetitive message. For example, on a dx-pedition, the ft-450d beacon might be activated on a 50 mhz frequency, to alert dxers to possible band openings. Cw m ode ...
Page 55
Page 53 ft-450d o peration m anual cw m ode o peration b eacon t ransmission (o n the a ir ) 1. Press and hold the [f] button for one second to enter the menu mode. The “ ” icon will ap- pear on the display. 2. Rotate the [dsp/sel] knob to select menu item “pnl-c.S”. 3. Press the [dsp/sel] knob to e...
Page 56
Page 54 ft-450d o peration m anual phones key b asic o peration 1. Press the [band ]/[band] buttons to select the 28 mhz or 50 mhz. Note: fm is only used in the 28 mhz and 50 mhz amateur bands covered in the ft-450d. Please do not use fm on any other bands. 2. Press the [mode ]/[mode] buttons to sel...
Page 57
Page 55 ft-450d o peration m anual r epeater o peration the ft-450d may be operated on 29 mhz and 50 mhz repeaters. Use this procedure to set the repeater shift direction, and the ctcss squelch mode & tone. 1. Press and hold the [f] button for one second to enter the menu mode again. The “ ” icon wi...
Page 58
Page 56 ft-450d o peration m anual t one s quelch o peration you may also use “tone squelch” whereby your receiver will be kept silent until an incoming signal bearing a matching ctcss tone is received. Your receiver’s squelch will then open in response to the reception of the required tone. 1. Pres...
Page 59
Page 57 ft-450d o peration m anual fm m ode o peration t one s earch s canning in operating situations where you don’t know the ctcss tone being used by another station or stations, you can command the radio to listen to the incoming signal and scan in search of the tone being used. Two things must ...
Page 60
Page 58 ft-450d o peration m anual (uk5-fm) (uk5-fe) (uk5-fl) (uk5-fk) mem-001 (uk5-fa) mem-498 mem-002 (uk5-fb) mem-499 mem-003 (uk5-fc) mem-500 qmb us5-005 us5-004 us5-001 us5-002 us5-003 m emory o peration c onvenient m emory functions the ft-450d contains 500 regular memories, labeled “mem-001” ...
Page 61
Page 59 ft-450d o peration m anual m emory o peration m emory g roups memory channels may be organized into as many as 10 convenient groups, for easy identification and selec- tion. For example, you might want to set aside memory groups for am bc stations, shortwave broadcast stations, contest frequ...
Page 62
Page 60 ft-450d o peration m anual m emory o peration r egular m emory o peration the regular memory of the ft-450d allows storage and recall of up to 500 memories, each storing frequency, mode, and a wide variety of status information detailed previously. Memories may be organized into as many as t...
Page 63
Page 61 ft-450d o peration m anual m emory o peration erasing memory channel data 1. Press the [v/m / mw] button, if necessary, to enter the memory mode. 2. Press the [f] button followed by the [v/m / mw] button. The blinking current memory channel number will be shown on the display, and the conten...
Page 64
Page 62 ft-450d o peration m anual m emory o peration labeling memories you may wish to append an alphanumeric “tag” (label) to a memory or memories, to aid in recollection of the channel’s use (such as a club name, etc.). This is easily accomplished using the menu mode. R egular m emory o peration ...
Page 65
Page 63 ft-450d o peration m anual m emory o peration to disable the alphanumeric “tag” (label) display. 1. Recall the memory channel that you wish to dis- able the alphanumeric “tag” (label). 2. Press and hold the [f] button for one second to enter the menu mode again. The “ ” icon will appear on t...
Page 66
Page 64 ft-450d o peration m anual m emory o peration h ome c hannel m emories two one-touch “home” channels are available, for special frequencies you use often. The hf band special “home” channel default is 29.300 mhz or 29.600 mhz, fm. The 50 mhz band “home” channel default is 50.100 mhz, 51.000 ...
Page 67
Page 65 ft-450d o peration m anual m emory o peration qmb (q uick m emory b ank ) the quick memory bank is independent from the regular and pms memories. You can quickly store operating parameters for later recall. Storage 1. Tune to the desired frequency on the vfo mode. 2. Press the [sto/vox] butt...
Page 68
Page 66 ft-450d o peration m anual s canning o peration you may scan either the vfo or the memories of the ft-450d, and the radio will halt the scan on any station with a signal strong enough to open the receiver’s squelch. Vfo and m emory s canning preparation when operating the scanning feature, s...
Page 69
Page 67 ft-450d o peration m anual s canning o peration vfo/memory scan 1. Rotate the [sql/rf gain] knob just to the point where the noise is silenced and the “ ” indi- cator on the display turns off. 2. Press the [scan/pms] key to initiate upward scanning (toward higher frequencies or higher memory...
Page 70
Page 68 ft-450d o peration m anual p rogrammable m emory s canning (pms) to limit scanning (and manual tuning) within a particular frequency range, you can use the programmable memory scanning (pms) feature, which utilizes two special-purpose memory pairs (“mem-p1l/mem-p1u” and “mem-p2l/mem-p2u”). T...
Page 71
Page 69 ft-450d o peration m anual o peration on a laska e mergency f requency : 5167.5 k h z (u.S. V ersion o nly ) section 97.401(d) of the regulations governing amateur radio in the united states permit emergency amateur communications on the spot frequency of 5167.5 khz by stations in (or within...
Page 72
Page 70 ft-450d o peration m anual m iscellaneous s ettings d isplay s ettings display dimmer you may adjust the brightness level with the five steps. 1. Press the [f] button, followed by the [meter/dim] button to enable adjustment of display dimmer. 2. Rotate the [dsp/sel] knob to select a comfort-...
Page 73
Page 71 ft-450d o peration m anual b eeper s etting beep volume you may adjust the beep volume level via the menu item “beepvol”. 1. Press and hold the [f] button for one second to enter the menu mode. The “ ” icon will ap- pear on the display. 2. Rotate the [dsp/sel] knob to select the menu item “b...
Page 74
Page 72 ft-450d o peration m anual beep tone you may adjust the beep tone to your desired tone via the menu item “beepton”. 1. Press and hold the [f] button for one second to enter the menu mode again. The “ ” icon will appear on the display. 2. Rotate the [dsp/sel] knob to select the menu item “bee...
Page 75
Page 73 ft-450d o peration m anual a utomatic p ower -o ff (apo) the “automatic power-off” (apo) feature will turn the radio completely off after a user-defined period of ptt or key/button inactivity. If you do not press any front panel keys or buttons, rotate the [main dial] knob, use the microphon...
Page 76
Page 74 ft-450d o peration m anual rtty (r adio t eletype ) o peration most rtty operation today is accomplished using a tnc or other computer-based system that utilizes afsk tones. For rtty operation using a terminal unit (tu) or the “fsk” output from a tnc, please see the discus- sion below. See a...
Page 77
Page 75 ft-450d o peration m anual p acket o peration packet operation is easily accomplished on the ft-450d by connecting your tnc (terminal node controller) to the transceiver, per the illustration. P acket s etup (i ncluding s ubcarrier f requency ) before operation can commence, change menu item...
Page 78
Page 76 ft-450d o peration m anual m iscellaneous afsk-b ased d ata m odes the ft-450d may also be used for a host of other ssb-based data modes. Please set up your system using the illustration as a guideline. Q uick p oint : when you have configured menu item “dig vox” to select the desired vox ga...
Page 79
Page 77 ft-450d o peration m anual m iscellaneous afsk-b ased d ata m odes n ote.
Page 80
Page 78 ft-450d o peration m anual m enu m ode the menu system permits extensive customization of the ft-450d. You can set up your transceiver to operate just the way you want. The menu’s 62 items are grouped into generally used categories from “ext mnu” to “voxgain”. The menu mode may be set to dis...
Page 81
Page 79 ft-450d o peration m anual m enu m ode m enu f unction a vailable v alues d efault s etting cwspeed 4 wpm (20cpm) ~ 60 wpm (300cpm) 12wpm (60cpm) cwstone (cw side tone) fix0 ~ fix100 or lnk-50 ~ lnk0 ~ lnk+50 fix10 or lnk-8 cwtrain (cw training) n: / a: / m: n: cwweigt (cw weight) 1/2.5 ~ 1/...
Page 82
Page 80 ft-450d o peration m anual ext mnu (extension menu) function: enables / disables the extended menu mode available values: on / off default: on off: the menu will only display the 16 most often used items. On: all 62 menu mode items will be displayed. A&fdial (am&fm dial) function: enables or...
Page 83
Page 81 ft-450d o peration m anual clar (clar dial/sel) function: setting of clar button available values: dial / sel default: dial defines which control knob is used for setting the clarifier-offset frequency. Clk sft (clock shift) function: shifting of cpu clock frequency available values: on / of...
Page 84
Page 82 ft-450d o peration m anual cwspeed function: sets the sending speed for the built-in electronic keyer. Available values: 4 wpm(20cpm)~60wpm(300cpm) default: 12wpm (60cpm) you can set the sending speed in either: wpm (words per minute), or cpm (characters per minute). To button between “wpm” ...
Page 85
Page 83 ft-450d o peration m anual lockmod (lock mode) function: sets the keylock for the panel buttones and dial available values: freq / panel / all default: freq selects the operation of the front panel’s [lock] key. Freq: locks the front panel keys and knobs related to frequency control. Front p...
Page 86
Page 84 ft-450d o peration m anual mic eq function: setting of the dsp microphone equalizer available values: 0 ~ 9 default: 0 you may select one of ten available dsp equaliza- tion techniques for transmitted microphone audio. 0: flat 1: low-frequency component is decreased. 2: mid-frequency compone...
Page 87
Page 85 ft-450d o peration m anual p m-up (mic-up pg) function: one of 52 functions can be preset and assigned to the [up] key of the micro- phone. Available values: please see page 16. Default: up presets of various functions can be assigned to the [up] key of the microphone using this option. Peak...
Page 88
Page 86 ft-450d o peration m anual stby bp (stby beep) function: setting of standby beep available values: off / on default: off off: no beep sound is transmitted. On: a beep is transmitted before returning to receive. The beep, transmitted when the ptt is released, will inform the other operators t...
Page 89
Page 87 ft-450d o peration m anual m enu m ode vox dly (vox delay) function: sets the “hang time” for the vox circuitry. Available values: 100 ~ 3000 (ms) (100 ms/step) default: 500 (ms) in vox operation, sets the delay time when the trans- mitter will return to receive after a voice pause. The dela...
Page 90
Page 88 ft-450d o peration m anual c loning you can transfer all data stored in one transceiver to another set by utilizing the handy “cloning” feature. This requires a user supplied cloning cable, which connects the cat jacks on the two transceivers, as shown below. To clone from one transceiver to...
Page 91
Page 89 ft-450d o peration m anual n ote.
Page 92
Page 90 ft-450d o peration m anual i nstallation of o ptional a ccessories a utomatic -m atching 200-m emory a ntenna t uner fc-40 o peration the fc-40 makes use of the control circuitry built into the transceiver, which allows the operator to control and monitor automatic operation of the fc-40, wh...
Page 93
Page 91 ft-450d o peration m anual i nstallation of o ptional a ccessories operation 1. Press the [tune] button briefly to activate the automatic antenna tuner. The “ ” icon will appear in the display. If the transceiver frequency is out of the amateur band, the “ ” icon will not appear. 2. Press an...
Page 94
Page 92 ft-450d o peration m anual i nstallation of o ptional a ccessories a ctive -t uning a ntenna s ystem (atas-100/-120/120a) o peration the optional atas-100, atas-120, or atas-120a active-tuning antenna system permits operation on a num- ber of hf bands (7/14/21/28 mhz) plus 50 mhz. The ft-450...
Page 95
Page 93 ft-450d o peration m anual i nstallation of o ptional a ccessories a ctive -t uning a ntenna s ystem (atas-100/-120/120a) o peration m anual t uning 1. Press the [tune] button briefly to activate the automatic antenna tuner. The “ ” icon will appear in the display. If the transceiver frequen...
Page 96
Page 94 ft-450d o peration m anual i nstallation of o ptional a ccessories c arrying h andle mhg-1 i nstallation the mhg-1 is a carrying handle designed to match ft-450d transceiver. Parts list handle ................................................................ 1pc handle end ......................
Page 97
Page 95 ft-450d o peration m anual i nstallation of o ptional a ccessories m ounting b racket mmb-90 i nstallation the mmb-90 is a mounting bracket designed to match the yaesu ft-450d transceiver. Parts list mounting bracket ........................................................ 1 pc double face a...
Page 98
Page 96 ft-450d o peration m anual general rx frequency range: 30 khz - 56 mhz (operating) 160 - 6 m (specified performance, amateur bands only) tx frequency ranges: 160 - 6 m (amateur bands only) frequency stability: ±1 ppm/hour (@+25 °c, after warmup) operating temperature range: 14 °f ~ 122 °f (–...
Page 99
Page 97 ft-450d o peration m anual s pecifications receiver circuit type: double-conversion superheterodyne intermediate frequencies: 67.899 mhz / 24 khz sensitivity (ipo “off”, att: off): ssb (2.4 khz, 10 db s+n/n) 0.25 µv (1.8 - 2.0 mhz) 0.25 µv (3.5 - 30 mhz) 0.20 µv (50 - 54 mhz) am (6 khz, 10 d...
Page 100
Page 98 ft-450d o peration m anual fcc n otice 1. Changes or modifications to this device not expressly approved by vertex standard could void the user’s authorization to operate this device. 2. This device complies with part 15 of the fcc rules. Operation is subject to the following two conditions;...
Page 101
Declaration of conformity we, yaesu uk ltd. Declare under our sole responsibility that the following equipment complies with the essential requirements of the directive 1999/5/ec and 2004/104/ec. Type of equipment: hf transceiver brand name: yaesu model number: ft-450 / ft-450d manufacturer: vertex ...
Page 102
Copyright 2010 vertex standard co., ltd. All rights reserved no portion of this manual may be reproduced without the permission of vertex standard co., ltd. Printed in japan 1012m-0y e h 0 2 4 h 2 5 0