- DL manuals
- Yaesu
- Transceiver
- FT-817ND
- Operating Manual
Yaesu FT-817ND Operating Manual - Ft-817
74
FT-817
ND
Operating Manual
O
PTIONAL
F
ILTERS
YF-122S/YF-122C/YF-122CN
1. Turn the transceiver’s power off by pressing and holding in the
switch for 1/2
second, then remove the FBA-28 Battery Case or FNB-85 Ni-MH Battery Pack from
the transceiver. Additionally, disconnect the DC cable from the INPUT: 13.8V jack
on the rear panel of the transceiver, when operating the FT-817
ND
with a DC power
supply.
2. Referring to Figure 1, remove the shoulder belt bracket and its two screws from both
side of the transceiver, then remove the five screws affixing the top case of the trans-
ceiver, and remove the top case; disconnect the speaker’s connector when you remove
the top case.
3. Refer to Figure 2 for the mounting locations for the optional filters. Position the filter so
that its connectors are aligned with the mounting pins on the board, and push it into
place.
4. Replace the top case (remember to replace the internal speaker’s plug), and connect the
FBA-28
Battery Case or FNB-85 Ni-MH Battery Pack (and/or attach the DC power
supply), and turn the transceiver on by pressing and holding in the
switch.
5. Change the setting of Menu #38 (OP FILTER
OP FILTER
OP FILTER
OP FILTER
OP FILTER
) to “SSB
SSB
SSB
SSB
SSB
” (if installing the YF-122S), or
“CW
CW
CW
CW
CW
” (for the YF-122C/YF-122CN).
6. Filter installation is now complete.
I
NSTALLATION
OF
O
PTIONAL
A
CCESSORIES
Figure 1
Figure 2
HF/VHF/UHF ALL MODE TRANSCEIVER
TRANSMIT/BUSY
BAND
DWN
UP
MODE
YF-122S/YF-122C
Mounting Location
/YF-122CN
Speaker's Connector
Summary of FT-817ND
Page 1
Hf/vhf/uhf all mode transceiver ft-817 nd o perating m anual yaesu musen co., ltd. Tennozu parkside building 2-5-8 higashi-shinagawa, shinagawa-ku, tokyo 140-0002 japan yaesu usa 6125 phyllis drive, cypress, ca 90630, u.S.A. Yaesu uk unit 12, sun valley business park, winnall close winchester, hamps...
Page 2: Contents
Introduction .................................................... 1 specifications .................................................. 2 accessories & options .................................... 4 plug pinout ...................................................... 5 installation ........................
Page 3: Ft-817
1 ft-817 nd operating manual the ft-817 nd is a compact, innovative multiband, multimode portable transceiver for the amateur radio mf/hf/vhf/uhf bands. Providing coverage of the 160-10 meter bands (include the 60 m band: usa version) plus the 6 m, 2 m, and 70 cm bands, the ft-817 nd includes operat...
Page 4: Ft-817
2 ft-817 nd operating manual g eneral frequency range: receive: 100 khz-30 mhz 50 mhz-54 mhz 76 mhz-154 mhz 420 mhz-470 mhz transmit: 160-6 meters (usa: includes 60 meters) 2 meters 70 centimeters (amateur bands only) 5.1675 mhz alaska emergency frequency (usa only) emission modes: a1a (cw), a3e (am...
Page 5: Ft-817
3 ft-817 nd operating manual r eceiver circuit type: double-conversion superheterodyne intermediate frequencies:1st: 68.33 mhz (ssb/cw/am/fm); 10.7 mhz (wfm) 2nd: 455 khz sensitivity: ssb/cw am fm 100 khz-500 khz – – – 500 khz-1.8 mhz – 32 μv – 1.8 mhz-28 mhz 0.25 μv 2 μv – 28 mhz-30 mhz 0.25 μv 2 μ...
Page 6: Ft-817
4 ft-817 nd operating manual s upplied a ccessories mh-31 a8j hand microphone fnb-85 ni-mh battery pack (9.6 v, 1400 mah) nc-72b/c/u or pa-48c/u battery charger fba-28 battery case (holds 8 “aa” size alkaline cells [not supplied]) yha-63 whip antenna for (50/144/430 mhz) e-dc-6 dc cable shoulder str...
Page 7: Ft-817
5 ft-817 nd operating manual p lug p inout.
Page 8: Ft-817
6 ft-817 nd operating manual c onnecting the s upplied yha-63 a ntenna your ft-817 nd is supplied with a three-section antenna, model yha-63 which is designed for optimum performance on the 50 mhz, 144 mhz, and 430 mhz. It also works well on the fm broadcast and other vhf bands. This antenna is inte...
Page 9: Ft-817
7 ft-817 nd operating manual i nstallation c onnecting the m icrophone to connect the microphone, plug its connector (latch side up) into the mic jack on the right side of the transceiver. Press it gently inward until you hear the “click” of the latch. to disconnect the microphone, press gently ...
Page 10: Ft-817
8 ft-817 nd operating manual a lkaline b attery i nstallation and u se the ft-817 nd is supplied with the fba-28 holder for alkaline “aa” cells. A fresh set of alkaline cells should provide approximately 5.5 hours of reception under typical conditions. 1. To install or replace the aa cells, first re...
Page 11: Ft-817
9 ft-817 nd operating manual i nstallation e xternal p ower c onnections the ft-817 nd may be connected to an external 13.8 volt dc power source providing at least 3 amps of continuous-duty current.. The supplied e-dc-6 dc cable may be used for dc connections. While connected to an external dc sourc...
Page 12: Ft-817
10 ft-817 nd operating manual fnb-85 n i -mh b attery p ack i nstallation and u se the supplied fnb-85 ni-mh battery pack provides 9.6 volts of dc power for your ft- 817 nd , with a maximum capacity of 1400 mah. Installation 1. To install the fnb-85 ni-mh battery pack, first remove the battery compa...
Page 13: Ft-817
11 ft-817 nd operating manual fnb-85 n i -mh b attery p ack i nstallation and u se i nstallation charging charging of the fnb-85 requires the use of either the supplied battery charger (nc-72b/ c or pa-48c/u), or an external 13.8 volt (±15%) dc source. If the battery charger is used, the ft-817 nd m...
Page 14: Ft-817
12 ft-817 nd operating manual pwr switch press and hold in the switch for one second to turn to the transceiver on or off. Af knob the (inner) knob adjusts the receiver audio volume level presented to the inter- nal or external speaker. Clockwise rotation increases the volume level. Sql/rf knob in t...
Page 15: Ft-817
13 ft-817 nd operating manual f ront p anel c ontrol & s witches func keys these three keys select many of the most important operating features of the trans- ceiver. When pressing the key, the current function of that key appears above each of the , , keys (along the bottom of the lcd); rotating th...
Page 16: Ft-817
14 ft-817 nd operating manual spl press the key to activate split frequency operation be- tween vfo-a and vfo-b. Tag press the key to select the display type (frequency or alpha-numeric tag) during memory operation. Pms press the key to activate the programmable memory scan feature. Ton press the ke...
Page 17: Ft-817
15 ft-817 nd operating manual nb press the key to activate t h e r e c e i v e r ’s i f n o i s e blanker. Pwr press the key to select the transmitter power output level (l ow 1, l ow 2, l ow 3, or h igh ). Vox press the key to enable the vox (voice-operated transmitter switching system) in the ssb,...
Page 18: Ft-817
16 ft-817 nd operating manual mic jack connect the supplied mh-31 a8j hand microphone to this jack. Sp/ph jack this 3.5-mm, 2-pin jack provides variable audio output for an external speaker (4 Ω ~ 16 Ω impedance) or earphones. The audio level varies according to the setting of the front panel’s knob...
Page 19: Ft-817
17 ft-817 nd operating manual r ear p anel c onnectors input:13.8v jack ( ) this is the dc power supply connection for the transceiver, used when operating the transceiver with an external power supply. Use the supplied dc cable to connect this jack to the car battery or base station dc power supply...
Page 20: Ft-817
18 ft-817 nd operating manual hi! I’m r.F. Radio, and i’m here to guide you through the fine points of the setup and use of your new ft-817nd. I know your anxious to get on the air, but i encourage you to read the “operation” section of this manual as thoroughly as possible, so you’ll get the most o...
Page 21: Ft-817
19 ft-817 nd operating manual o perating b and s election this transceiver covers an incredibly wide fre- quency range, over which a number of different operating modes are used. Therefore, this transceiver’s frequency coverage has been di- vided into different operating bands, each of with has its ...
Page 22: Ft-817
20 ft-817 nd operating manual o peration m enu q uick s tart many aspects of this transceiver’s configuration may be customized using the convenient “menu” system, which allow you to configure many “set and forget” settings just the way you want to. A full discussion of the menu system beings on pag...
Page 23: Ft-817
21 ft-817 nd operating manual o peration s etting the o perating f requency 1. In the “ssb/cw/dig” modes, rotate the knob to set the frequency. Clockwise rotation of the knob increases the op- erating frequency. 2. In the “am/fm/pkt” modes, rotate the knob to set the frequency. Clockwise rotation of...
Page 24: Ft-817
22 ft-817 nd operating manual o peration o peration on 5 mh z b and (u.S. V ersion o nly ) the ft-817 nd includes the capability for transmission and reception on the five spot frequen- cies assigned to the amateur service in the united states. To operate on the 5 mhz band: 1. Press the key once to ...
Page 25: Ft-817
23 ft-817 nd operating manual c larifier (r eceiver i ncremental t uning ) the clarifier (rit) allows you to set an offset of up to ±9.99 khz of the receive frequency relative to your transmit frequency. To achieve a wider offset than this, you may use the “split” operating mode, described later. 1....
Page 26: Ft-817
24 ft-817 nd operating manual r eceiver a ccessories if shift the receiver’s if shift feature is an effective interference-reduction tool, which allows you to shift the passband response higher or lower without changing the pitch of the incom- ing signal. 1. Press the switch for one second to acti- ...
Page 27: Ft-817
25 ft-817 nd operating manual agc (a utomatic g ain c ontrol ) the receiver recovery time constant of the agc system may be modified to match your operating needs. 1. Press the key momentarily, then rotate the knob, as needed, until operating function row 8 [nb nb nb nb nb , agc agc agc agc agc] app...
Page 28: Ft-817
26 ft-817 nd operating manual att (f ront e nd a ttenuator ) the attenuator will reduce all signals (and noise) by 10 db, and it may be used to make reception more pleasant under extremely noisy conditions. This feature is not available on the 144 mhz and 430 mhz. 1. Press the key momentarily, then ...
Page 29: Ft-817
27 ft-817 nd operating manual a utomatic p ower -o ff f eature the apo feature helps conserve battery life by automatically turning the transceiver off after a user-defined period of time within which there has been no dial or key activity. The available selections for the time before power-off are ...
Page 30: Ft-817
28 ft-817 nd operating manual ssb t ransmission basic setup/operation 1. Press the / key so as to select either ssb (lsb/usb) mode. If you are operating on the 7 mhz or lower bands, select the lsb mode. If you are operating on the 14 mhz or higher bands, select the usb mode. 2. Press the key momenta...
Page 31: Ft-817
29 ft-817 nd operating manual ssb t ransmission t ransmitter o peration vox operation the vox system provides automatic transmit/receive switching based on voice input to the microphone. With the vox system enabled, you do not need to press the ptt switch in order to transmit. 1. Press the key momen...
Page 32: Ft-817
30 ft-817 nd operating manual cw t ransmission operation using straight key/external keying device when using a straight key, an external electronic keyer, or a computer-generated keying device, please follow the instructions in this section. 1. Insert your key’s (three-conductor) plug into the rear...
Page 33: Ft-817
31 ft-817 nd operating manual 8. You also can adjust the cw sidetone pitch using menu #20 (cw pitch cw pitch cw pitch cw pitch cw pitch ). This adjust- ment also controls the bfo offset (actual pitch of your transmitted signal relative to your current receive frequency). To adjust the cw sidetone pi...
Page 34: Ft-817
32 ft-817 nd operating manual operation using built-in electronic keyer the built-in electronic keyer provides a convenient method of generating cw. The elec- tronic keyer includes weight and speed adjustments. 1. Connect your keyer paddle’s cable to the key jack on the rear panel of the transceiver...
Page 35: Ft-817
33 ft-817 nd operating manual t ransmitter o peration fm t ransmission basic setup/operation 1. Press the / key so as to select the fm mode. 2. Press the microphone’s ptt switch, and speak into the microphone in a normal voice. 3. Release the ptt switch to return to the receive mode. 4. If you get r...
Page 36: Ft-817
34 ft-817 nd operating manual 4. Press the (ton ton ton ton ton) key to activate the ctcss tone encoder, which provides a subaudible repeater access tone. One press of the (ton ton ton ton ton) key will activate the ctcss tone encoder. In this situation, you will observe the “ ” indicator on the dis...
Page 37: Ft-817
35 ft-817 nd operating manual tone search scanning in operating situations where you don’t know the ctcss tone being used by an- other station, you can command the radio to listen to the incoming signal and scan in search of the tone being used. To scan for the ctcss tone in use: 1. Press the key mo...
Page 38: Ft-817
36 ft-817 nd operating manual dcs operation another form of tone access control is digital code squelch, or dcs. It is a newer, more advanced tone system that is less susceptible to false triggering than ctcss. A dcs en- coder/decoder is built into your transceiver, and operation is very similar to ...
Page 39: Ft-817
37 ft-817 nd operating manual arts tm (a uto r ange t ranspond s ystem ) operation the arts tm system uses dcs signaling to inform you when you and another arts™-equipped station are within communications range. This can be especially valuable during search-and- rescue operations, as a base station ...
Page 40: Ft-817
38 ft-817 nd operating manual d igital m ode o peration (ssb-b ased afsk) the ft-817 nd provides extensive capability for digital mode operation on the hf, vhf, and uhf bands. The use of afsk (audio frequency-shifted keying) configurations al- lows a wide variety of different communication modes to ...
Page 41: Ft-817
39 ft-817 nd operating manual 4. If the optional yf-122c 500 hz filter has been installed, it may be used for rtty work. Recall operating function row 7 [ipo ipo ipo ipo ipo , att att att att att , nar nar nar nar nar] then press the (nar nar nar nar nar) key to engage the narrow filter. 5. To set u...
Page 42: Ft-817
40 ft-817 nd operating manual “user” defined digital modes also provided in the ft-817 nd are two convenient “user” digital modes, one each pro- viding usb- and lsb-side injection, which may be used for sstv, fax, pactor, and other digital operating modes. Here is an example involving the configurat...
Page 43: Ft-817
41 ft-817 nd operating manual p acket (1200/9600 bps fm) o peration the ft-817 nd is designed for operation on either 1200 bps or 9600 bps packet, and setup is similar to that described previously for ssb-based modes. A separate data input adjust- ment is provided, allowing you to optimize the devia...
Page 44: Ft-817
42 ft-817 nd operating manual am t ransmission the ft-817 nd utilizes low-level amplitude modulation of an early stage for transmission purposes. This capability is primarily provided for emergency use only, as low-power op- eration typically utilizes more efficient transmission/reception modes. The...
Page 45: Ft-817
43 ft-817 nd operating manual t ime -o ut t imer most often used on fm, the transmitter’s time-out timer (tot) feature disables the trans- mitter after a user-defined period of transmission. This feature may be useful in preventing a “stuck microphone” (accidental closure of the ptt switch) from cau...
Page 46: Ft-817
44 ft-817 nd operating manual qmb c hannel qmb channel storage 1. Tune in the desired frequency and set the operating mode and bandwidth. If this is an fm channel, set up any required ctcss/dcs and repeater shift configurations. 2. Press and hold in the key until a double “beep” is heard. The second...
Page 47: Ft-817
45 ft-817 nd operating manual m emory o peration on “r egular ” m emory c hannels normal memory storage 1. Tune in the desired frequency, and set the operating mode and bandwidth. If this is an fm channel, set up any required ctcss/dcs and repeater shift configurations. Stan- dard (default) repeater...
Page 48: Ft-817
46 ft-817 nd operating manual memory channel recall 1. If you currently are in the vfo tuning mode, press the key once to enter the “memory” mode (a memory channel number “m- m- m- m- m- nnn nnn nnn nnn nnn ” will appear on the display in she space previously occupied by “vfoa vfoa vfoa vfoa vfoa ” ...
Page 49: Ft-817
47 ft-817 nd operating manual m emory o peration masking memory frequency data stored on a memory channel can be deleted, if desired, from any memory channel except channel “1.” the deletion process is not a “hard” erasure, so if you erase a channel by mistake using this procedure, the memory channe...
Page 50: Ft-817
48 ft-817 nd operating manual m emory o peration on “home” c hannel m emories four special one-touch “home” channels are available, for special frequencies you use often. Either “simplex” or “split” frequency/mode data may be stored in the “home” chan- nel locations. Special “home” channels are avai...
Page 51: Ft-817
49 ft-817 nd operating manual l abeling m emories you may wish to append an alpha-numeric “tag” (label) to a memory or memories, to aid in recollection of the channel’s intended use (such as a club name, etc.). This is easily accom- plished using the menu mode. 1. Recall the memory channel onto whic...
Page 52: Ft-817
50 ft-817 nd operating manual the spectrum scope monitor allows viewing of operating activity on 5 channels above and 5 channels below the current operating channel in the vfo mode. When the spectrum scope monitor is activated, the display indi- cates the relative signal strength on channels immedia...
Page 53: Ft-817
51 ft-817 nd operating manual the smart search tm feature automatically stores frequencies where activity is encountered on the current band. When smart search tm is engaged, the transceiver quickly searches above your current frequency, storing active frequencies as it goes (without stopping on the...
Page 54: Ft-817
52 ft-817 nd operating manual this transceiver contains a wide variety of scanning capabilities. Whether you are in the vfo mode or one of the memory modes, scanning operation is fundamentally identical in all configurations, but with the following differences: in the vfo mode, scanning causes the...
Page 55: Ft-817
53 ft-817 nd operating manual scan skip programming (memory mode only) among the memories you have programmed, there may be some stations which you do not wish to scan. For example, broadcast signals (which are transmitted continuously) will cause the scanner to stop, and such channels may be skippe...
Page 56: Ft-817
54 ft-817 nd operating manual programmable memory scan (pms) operation to limit scanning (or tuning) within a particular frequency range, you can use the program- mable memory scanning (pms) feature, which utilizes special-purpose memory pair (“m- m- m- m- m- pl pl pl pl pl ” and “m-pu m-pu m-pu m-p...
Page 57: Ft-817
55 ft-817 nd operating manual note the frequency resolution for these sub-band limits is 100 khz, although the channel resolution of the sub-band limit memories in whatever you have selected as the current step size. As a result, the frequencies stored in these special memories (m-pl m-pl m-pl m-pl ...
Page 58: Ft-817
56 ft-817 nd operating manual d ual w atch o peration dual watch is similar, in some respects, to scanning. In dual watch, however, the trans- ceiver monitors (squelched) on the vfo-a frequency while periodically checking vfo-b for activity (or vice-versa). A typical example might be for you to set ...
Page 59: Ft-817
57 ft-817 nd operating manual section 97.401(d) of the regulations governing amateur radio in the united states permit emergency amateur communications on the spot frequency of 5167.5 khz by stations in (or within 92.6 km of) the state of alaska. This frequency is only to be used when the immedi- at...
Page 60: Ft-817
58 ft-817 nd operating manual menu item function available values default 01 144 ars activate/deactivate the automatic repeater shift off/on 1 when operating on the 144 mhz band 02 430 ars activate/deactivate the automatic repeater shift off/on 1 when operating on the 430 mhz band 03 9600 mic adju...
Page 61: Ft-817
59 ft-817 nd operating manual m enu o peration 1: depends on transceiver version. 2: depends on operating band and transceiver version. Menu item function available values default 19 cw paddle select the keyer paddle's wiring configuration normal/reverse normal 20 cw pitch setting of the pitch of ...
Page 62: Ft-817
60 ft-817 nd operating manual menu item 01 [144 ars 144 ars 144 ars 144 ars 144 ars] function: activate/deactivate the automatic repeater shift when operating on the 144 mhz band. Available values: off/on default: on (depending on transceiver version) menu item 02 [430 ars 430 ars 430 ars 430 ars 43...
Page 63: Ft-817
61 ft-817 nd operating manual menu item 09 [arts beep arts beep arts beep arts beep arts beep] function: select the arts beep mode. Available values: off/range/all default: range off: no alert beeps sound; you must look at the display to determine current arts status. Range: a high tone beep will so...
Page 64: Ft-817
62 ft-817 nd operating manual menu item 15 [color color color color color] function: select the illumination color for the lcd illumination. Available values: color1 (blue)/color2 (amber)/color3 (violet) default: color1(blue) menu item 16 [contrast contrast contrast contrast contrast] function: sett...
Page 65: Ft-817
63 ft-817 nd operating manual menu item 21 [cw speed cw speed cw speed cw speed cw speed] function: set the sending speed for the built-in electronic keyer. Available values: 4wpm ~ 60 wpm/20cpm ~ 300 cpm default: 12 wpm (60 cpm) you can set the sending speed according to either of two units of spee...
Page 66: Ft-817
64 ft-817 nd operating manual menu item 27 [dig shift dig shift dig shift dig shift dig shift] function: define the carrier frequency offset during dig (user-l or user-u) mode operation. Available values: –3000 ~ +3000 hz default: 0 hz menu item 28 [emergency emergency emergency emergency emergency]...
Page 67: Ft-817
65 ft-817 nd operating manual menu item 32 [lock mode lock mode lock mode lock mode lock mode] function: select the operation of the front panel’s key. Available values: dial/freq/panel default: dial dial: locks knob only freq: locks front panel keys and knobs related to frequency control (such as a...
Page 68: Ft-817
66 ft-817 nd operating manual menu item 36 [mic key mic key mic key mic key mic key] function: enable/disable cw keying by the microphone’s [up]/[dwn] keys. Available values: off/on default: off when this menu item is set to “on,” press the microphone’s [up] key to send a “dot,” and press the microp...
Page 69: Ft-817
67 ft-817 nd operating manual menu item 43 [scope scope scope scope scope] function: select the spectrum scope mode. Available values: cont/chk default: cont cont: the spectrum scope sweeps continuously. Chk: the spectrum scope sweeps one cycle every 10 seconds. Menu item 44 [sidetone sidetone sidet...
Page 70: Ft-817
68 ft-817 nd operating manual menu item 51 [vox gain vox gain vox gain vox gain vox gain] function: set the gain of the vox circuitry’s input audio detector. Available values: 1 ~ 100 default: 50 menu item 52 [extend extend extend extend extend] function: enable/disable the extended menu items (#53 ...
Page 71: Ft-817
69 ft-817 nd operating manual c loning you can transfer all data stored in one transceiver to another set by utilizing the handy “cloning” feature. This requires a user-constructed cloning cable which connects the acc jacks on the two transceivers as shown below. To clone from one transceiver to ano...
Page 72: Ft-817
70 ft-817 nd operating manual the ft-817 nd ’s cat system allows the transceiver to be controlled by a personal com- puter. This allows multiple control operations to be fully automated as a single mouse click, or it allows a third-party software package (such as contest logging software) to communi...
Page 73: Ft-817
71 ft-817 nd operating manual cat s ystem p rogramming cat data protocol all commands sent from the computer to the transceiver consist of five-byte blocks, with up to 200 ms between each byte. The last byte in each block is the instruction opcode, while the first four bytes of each block are argume...
Page 74: Ft-817
72 ft-817 nd operating manual command title lock on/off ptt on/off set frequency operating mode clar on/off clar frequency vfo-a/b split on/off repeater offset repeater offset ctcss/dcs mode ctcss tone dcs code read rx status read tx status read frequency & mode status power on/off p1 p1 p1 p1 p1 p1...
Page 75: Ft-817
73 ft-817 nd operating manual ctcss tone frequency (hz) 67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 156.7 159.8 162.2 165.5 167.9 171.3 173.8 177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5 203.5 206.5 210....
Page 76: Ft-817
74 ft-817 nd operating manual o ptional f ilters yf-122s/yf-122c/yf-122cn 1. Turn the transceiver’s power off by pressing and holding in the switch for 1/2 second, then remove the fba-28 battery case or fnb-85 ni-mh battery pack from the transceiver. Additionally, disconnect the dc cable from the in...
Page 77: Ft-817
75 ft-817 nd operating manual o ptional h igh -s tability r eference o scillator tcxo-9 the tcxo-9 provides high stability over a wide range of ambient temperatures, so as to enhance digital-mode operating. 1. Turn the transceiver’s power off by pressing and holding in the switch for 1/2 second, the...
Page 78: Ft-817
76 ft-817 nd operating manual some or all transceiver settings can be reset to their factory-default states using one of the following power-on routines: + power on: reset all memories and following menu setting to factory-default. Menu #06 (am step am step am step am step am step ), 23 (dcs code dc...
Page 79: Ft-817
77 ft-817 nd operating manual s etup of m emories for l ow e arth o rbit (leo) fm s atellite o peration although the ft-817 nd is not capable of “full duplex” operation (simultaneous transmis- sion and reception), its flexible memory system is ideal for configuring a set of memories for leo satellit...
Page 80: Ft-817
78 ft-817 nd operating manual press the key momentarily, then rotate the knob one click counter-clockwise to re-select operating function row 1 [a a a a a/b b b b b , a=b a=b a=b a=b a=b , spl spl spl spl spl] . Press the (a a a a a/b b b b b) key to select vfob vfob vfob vfob vfob (145.970 mhz). Ag...
Page 81: Ft-817
79 ft-817 nd operating manual s etup of m emories for l ow e arth o rbit (leo) fm s atellite o peration a ppendix a complete set of frequencies may be stored for each leo satellite you wish to utilize, and once configured, the ft-817 nd provides a flexible and easy-to-use earth station capability fo...
Page 82: Ft-817
80 ft-817 nd operating manual a ppendix level 0.33 v 0.67 v 1.00 v band 1.8 mhz 3.5 mhz 7 mhz band 10 mhz 14 mhz 18 mhz band 21 mhz 24.5 mhz 28 mhz band 50 mhz 144 mhz 430 mhz level 3.33 v 3.67 v 4.00 v level 1.33 v 1.67 v 2.00 v level 2.33 v 2.67 v 3.00 v band data format the ft-817 nd band data fo...
Page 83
1. Changes or modifications to this device not expressly approved by yaesu musen could void the user’s authorization to operate this device. 2. This device complies with part 15 of the fcc rules. Operation is subject to the following two conditions; (1) this device may not cause harmful interference...
Page 84
Copyright 2013 yaesu musen co., ltd. All rights reserved. No portion of this manual may be reproduced without the permission of yaesu musen co., ltd. Printed in japan 1308h-yt e 1 3 7 7 1 0 1 1.