1. DL manuals
  2. Yaesu
  3. Transceiver
  4. FTM-3200DR
  5. Advance Manual

Yaesu FTM-3200DR Advance Manual

Summary of FTM-3200DR

  • Page 1

    Ftm-3200dr advance manual vol dial sql txpo d w m w setup rev d/a v / m m h z c4fm/fm vhf digital/analog transceiver.

  • Page 2: Contents

    2 contents ftm-3200dr advance manual basic operation .............................................................................................................. 3 microphone gain setting ................................................................................................ 3 rf squelch ...

  • Page 3: Ftm-3200Dr Advance Manual

    3 ftm-3200dr advance manual basic operation microphone gain setting the microphone gain has been programmed at the factory to a level that should be satisfactory for the supplied mh-48a6ja microphone. If an after-market microphone is used, you may wish to set a different mic gain level. 1. Press and...

  • Page 4: Ftm-3200Dr Advance Manual

    4 ftm-3200dr advance manual advanced operation programming the key assignments default ftm-3200dr key functions have been assigned to the microphone [ p1 ]/[ p2 ]/[ p3 ]/ [ p4 ] keys at the factory. The user may change these key function assignments, if quick access to another function is desired. T...

  • Page 5: Advanced Operation

    5 advanced operation ftm-3200dr advance manual split tone operation the ftm-3200dr can be configured to operate in a “split tone” system via the setup menu, to facilitate operation on repeaters using a mix of both ctcss and dcs control. 1. Press and hold in the [ mhz ( setup )] key for one second to...

  • Page 6: Advanced Operation

    6 advanced operation ftm-3200dr advance manual tone search when the ctcss tone being transmitted by another station is not known, you can tune the radio to the incoming signal and activate tone scan to search for and identify the tone being used. To scan for the tone in use: 1. Set the transceiver u...

  • Page 7: Advanced Operation

    7 advanced operation ftm-3200dr advance manual dcs search when the dcs code being transmitted by another station is not known, you can tune the radio to the incoming signal and activate dcs code scan to search for and identify the dcs code being used. To scan for the dcs in use: 1. Set the transceiv...

  • Page 8: Advanced Operation

    8 advanced operation ftm-3200dr advance manual epcs (enhanced paging & code squelch) operation the ftm-3200dr includes an enhanced ctcss tone encoder/decoder and a dedicated microprocessor providing paging and selective calling features. This allows placing a call to a specific station (paging), and...

  • Page 9: Advanced Operation

    9 advanced operation ftm-3200dr advance manual activating the enhanced paging & code squelch system 1. Press and hold in the [ mhz ( setup )] key for one second to enter the set mode. 2. Rotate the dial knob to select “ sql type 42 ”. Vol dial sql txpo d w m w setup rev d/a v / m m h z 3. Press the ...

  • Page 10: Advanced Operation

    10 advanced operation ftm-3200dr advance manual dtmf operation dtmf tones (dual tone multi frequencies) are the tones you hear when dialing from a telephone keypad. The ftm-3200dr transceiver can transmit the dtmf codes by using the keys on the microphone or recalling registered number strings from ...

  • Page 11: Advanced Operation

    11 advanced operation ftm-3200dr advance manual registering a dtmf code 1. Press and hold in the [ mhz ( setup )] key for one second to enter the set mode. 2. Rotate the dial knob to select “ dt set 17 ”. Vol dial sql txpo d w m w setup rev d/a v / m m h z 3. Press the [ mhz ( setup )] key momentari...

  • Page 12: Advanced Operation

    12 advanced operation ftm-3200dr advance manual transmitting the registered dtmf code 1. Press and hold in the [ mhz ( setup )] key for one second to enter the set mode. 2. Rotate the dial knob to select “ dt auto 15 ”. Vol dial sql txpo d w m w setup rev d/a v / m m h z 3. Press the [ mhz ( setup )...

  • Page 13: Advanced Operation

    13 advanced operation ftm-3200dr advance manual setting dtmf autodialer tx delay time a longer delay may be set between the time the transmitter is keyed and the first dtmf digit is sent: 1. Press and hold in the [ mhz ( setup )] key for one second to enter the set mode. 2. Rotate the dial knob to s...

  • Page 14: Ftm-3200Dr Advance Manual

    14 ftm-3200dr advance manual memory operation split memory a separate transmit frequency may be registered to a memory channel to which a receive frequency has already been registered. 1. In the vfo mode, select the transmit frequency to be registered. 2. Press and hold the [ v/m ( mw )] key for one...

  • Page 15: Memory Operation

    15 memory operation ftm-3200dr advance manual naming a memory channel you may wish to append an alphanumeric “tag” (label) to each memory, to aid in recollection of the channel’s use (such as club name, etc.). 1. Recall the memory channel on which you wish to append a label. 2. Press and hold in the...

  • Page 16: Ftm-3200Dr Advance Manual

    16 ftm-3200dr advance manual scanning scan resume options select one of the three receiving operations to be performed after the scanning stops. (1) restart scanning after receiving the frequency for the set amount of time. Select from 2.0 to 10.0 seconds (0.5 step). (2) continue receiving the frequ...

  • Page 17: Scanning

    17 scanning ftm-3200dr advance manual memory skip scanning when some memory channels are continuously active, you may wish to skip them during scanning , but still have them available for manual selection . To mask a memory to be skipped (only) during scanning, use the following procedure: 1. Set th...

  • Page 18: Scanning

    18 scanning ftm-3200dr advance manual preferential memory scan the ftm-3200dr also allows setting up a “preferential scan list” of channels, which you can “flag” within the memory system. The flagged channels are designated by an “ ” icon when they are selected, one by one, for the preferential scan...

  • Page 19: Scanning

    19 scanning ftm-3200dr advance manual programmable memory scan (pms) the ftm-3200dr can be set to tune or scan only the frequencies between user-defined lower and band limits. Example: set up a pms channel by registering a lower frequency of 144.300 mhz, and an upper frequency of 148.000 mhz to the ...

  • Page 20: Scanning

    20 scanning ftm-3200dr advance manual scanning the programmable memory channels 1. Press the [ v/m ( mw )] key to enter memory mode. 2. Turn the dial knob, or use the microphone keypad, to recall the upper or lower fre- quency pms memory channel (l1 or u1). 3. Press the [ # ] key on the mh-48a6ja mi...

  • Page 21: Scanning

    21 scanning ftm-3200dr advance manual priority channel scanning (dual watch) the ftm-3200dr’s scanning features include a two-channel scanning capability which allows operating on a vfo, memory channel, or home channel, while periodically checking a user- defined memory channel for activity. If a st...

  • Page 22: Ftm-3200Dr Advance Manual

    22 ftm-3200dr advance manual gm function gm alert beep to alert you to the current status of gm operation, the gm (group monitor) feature allows two kinds of alert beeps (with the additional option of turning them off). Depending on your location and the potential annoyance associated with frequent ...

  • Page 23: Ftm-3200Dr Advance Manual

    23 ftm-3200dr advance manual clone the ftm-3200dr includes a convenient “clone” feature, which allows the memory and configuration data from one transceiver to be transferred to another ftm-3200dr. This can be particularly useful when configuring a number of transceivers for a public service operati...

  • Page 24: Ftm-3200Dr Advance Manual

    24 ftm-3200dr advance manual setup (menu) mode the ftm-3200dr setup (menu) mode, already described in parts of many previous chapters, is easy to activate and setup. The menus may be used to configure many of transceiver parameters, some of which have not been detailed previously. Use the following ...

  • Page 25: Setup (Menu) Mode

    25 setup (menu) mode ftm-3200dr advance manual menu item function available values default 17: dt set loading of the dtmf autodialer memo- ries. --- --- 18: dt speed setting of the dtmf autodialer sending speed. 50/100 50 ms 19: dw rvrt enables/disables the “priority channel revert” feature. On/off ...

  • Page 26: Setup (Menu) Mode

    26 setup (menu) mode ftm-3200dr advance manual menu item function available values default 41: sql exp enables/disables the split ctcss/dcs coding. On/off off 42: sql type selects the tone encoder and/or decod- er mode. Tone/tsql/dcs/ rv tone/pager/off off 43: step sets the frequency synthesizer ste...

  • Page 27: Ftm-3200Dr Advance Manual

    27 ftm-3200dr advance manual menu selection details 1 apo function: enables/disables the automatic power off feature. Available values: 0.5 h to 12.0 h (0.5 h/step) / off default: off 2 bclo function: enables/disables the busy channel lock-out feature. Available values: on / off default: off 3 bep k...

  • Page 28: Menu Selection Details

    28 menu selection details ftm-3200dr advance manual 9 dcs code function: setting of the dcs code. Available values: 104 standard dcs codes default: 023 dcs code 023 025 026 031 032 036 043 047 051 053 054 065 071 072 073 074 114 115 116 122 125 131 132 134 143 145 152 155 156 162 165 172 174 205 212...

  • Page 29: Menu Selection Details

    29 menu selection details ftm-3200dr advance manual 14 dsq type function: sets the squelch type in digital mode. Available values: code / break / off default: off code: outputs sound only when receiving signals containing the sql code corresponding to the code you setting. Break: regardless of the s...

  • Page 30: Menu Selection Details

    30 menu selection details ftm-3200dr advance manual 21 gm intvl function: selects the automatic gm beacon interval. Available values: normal / long default: normal 22 lcd dmmr function: setting of the front panel display’s illumination level. Available values: level 1 - level 4 default: level 4 23 l...

  • Page 31: Menu Selection Details

    31 menu selection details ftm-3200dr advance manual 4. Repeat the previous step as necessary to complete the message (up to 8 characters). 5. To correct a mistake, press the [ sql ( txpo )] key to backspace the cursor; now re-en- ter the correct letter/number. 6. When the desired opening message is ...

  • Page 32: Menu Selection Details

    32 menu selection details ftm-3200dr advance manual 34 radio id function: displays the transceiver ids. Radio id is a 5-digit code consisting of alphanumeric characters that is written into the transceiver during factory production. The radio id cannot be edited. 35 rf sql function: adjusts the rf s...

  • Page 33: Menu Selection Details

    33 menu selection details ftm-3200dr advance manual 41 sql exp function: enables/disables the split ctcss/dcs coding. Available values: on / off default: off when this set mode item is set to “on”, the following additional parameters are available after the “pager” parameter when configuring set mod...

  • Page 34: Menu Selection Details

    34 menu selection details ftm-3200dr advance manual 46 tot function: sets the time-out timer.. Available values: 0.5 min - 10.0 min (0.5 min step) / off default: 3.0 min the time-out timer shuts off the transmitter after continuous transmission of the programmed time. 47 ts mute function: enables/di...

  • Page 35: Menu Selection Details

    35 menu selection details ftm-3200dr advance manual 53 my call function: sets your station call sign. Here’s how to input the call sign: 1. Press the [ mhz ( setup )] key momentarily. The currently registered call sign id is shown. 2. Rotate the dial knob to select the first letter/number of the cal...

  • Page 36

    Yaesu musen co., ltd. All rights reserved. No portion of this manual may be reproduced without the permission of yaesu musen co., ltd. Copyright 2016 1602-a0 yaesu musen co., ltd. Tennozu parkside building 2-5-8 higashi-shinagawa, shinagawa-ku, tokyo 140-0002 japan yaesu usa 6125 phyllis drive, cypr...