- DL manuals
- Yaesu
- Transceiver
- FTM-350 - APRS
- Manual
Yaesu FTM-350 - APRS Manual - page 17
FTM-350 S
ERIES
APRS
®
M
ANUAL
17
B
EACON
T
YPE
D
ETAILS
If necessary, press the [F] key repeatedly, until the [SMART FUNCTION] key’s category
changes to “F-3” mode, then press the [S
LIST] key to open the “Station List” window.
D
ISPLAY
Mic-E
FIXED
fixed
MOVING
moving
WEATHER
weather
OBJECT
object
ITEM
item
KILLOBJ
KILLITM
killobj
killitm
STATUS
GGA/GLL
GPRMC
OTHER
!!EMG!!
B
EACON
T
YPE
Mic Encoder Station (Some Mic Encoder Stations append the transceiver name (such
as the FTM-350, VX-8 etc.) instead of “Mic-E” to the beacon).
Position “Fixed” Station.
(
Compressed) Position “Fixed” Station.
Mobile Station.
(
Compressed) Mobile Station.
Weather Station.
(
Compressed) Weather Station.
Object Station.
(
Compressed) Object Station.
Item Station.
(
Compressed) Item Station.
Killed Object Station.
Killed Item Station.
Killed (
Compressed) Object Station.
Killed (
Compressed) Item Station.
Status Station.
Raw NMEA Data.
Raw NMEA Data.
Station except APRS Station.
Emergency Beacon from the Mic Encoder Station.
R
EF
. P
AGE
18
19 ~ 21
19 ~ 21
22
22
23
23
24
24
24
24
24
24
24
24
25
26
26
27
15
(
Compressed) some part of the Beacon message is compressed.
R
ECEIVING
AN
APRS
®
B
EACON
Summary of FTM-350 - APRS
Page 1
Ftm-350 s eries aprs ® m anual 1 the ftm-350 series transceiver is equipped with a 1200/ 9600bps ax.25 data modem to enable aprs ® (auto- matic packet reporting system) operation. The automatic packet reporting system (aprs ® ) is a software program and registered trademark of bob bruninga, wb4apr. ...
Page 2
Ftm-350 s eries aprs ® m anual 2 c ontents preparations ...................................................................................................................... 4 flow chart ...................................................................................................................
Page 3
Ftm-350 s eries aprs ® m anual 3 c ontents transmit an aprs tm beacon ........................................................................................ 36 manual transmission .................................................................................................. 36 automatic transm...
Page 4
Ftm-350 s eries aprs ® m anual 4 p reparations f low c hart the optional gps antenna unit is installed. (see page 5) the optional gps antenna unit is not installed. (see page 5) set the clock time of the transceiver. See page 44 on the ftm-350 series operating manual enter your position (log/lat). (...
Page 5
Ftm-350 s eries aprs ® m anual 5 a bout the gps a ntenna t o o perate the aprs with the o ptional gps a ntenna u nit when the optional fgps-1 or fgps-2 gps antenna unit is installed in the transceiver, the clock time and your location (longitude/latitude) are determined from the satellite data autom...
Page 6
Ftm-350 s eries aprs ® m anual 6 p reparations p osition s etting this paragraph explains a method to enter your position (longitude/latitude) when an optional fgps-1 or fgps-2 gps antenna unit is not in use. 1. Press the [set] key to enter the set mode. 2. Rotate the left side [dial] knob to select...
Page 7
Ftm-350 s eries aprs ® m anual 7 p reparations c allsign s etting 1. Press the [set] key to enter the set mode. 2. Rotate the left side [dial] knob to select “aprs/pkt” group, then press the left side [dial] knob. 3. Rotate the left side [dial] knob to select set mode item “e29 my callsign”. 4. Pres...
Page 8
Ftm-350 s eries aprs ® m anual 8 p reparations a ctivate the aprs f unction 1. Press the [set] key to enter the set mode. 2. Rotate the left side [dial] knob to select “aprs/pkt” group, then press the left side [dial] knob. 3. Rotate the left side [dial] knob to select set mode item “e05 aprs modem”...
Page 9
Ftm-350 s eries aprs ® m anual 9 p reparations s elect the b aud r ate of the aprs f unction this paragraph selects the baud rate of the aprs function. When selecting a baud rate of “1200 bps”, you may operate aprs using afsk 1200 bps packet. When selecting a baud rate of “9600 bps”, you may operate...
Page 10
Ftm-350 s eries aprs ® m anual 10 s elect y our i con this paragraph selects the icon which will be displayed to identify your station on the monitors of other aprs stations. You may choose the icon from the 46 symbols (see be- low). 1. Press the [set] key to enter the set mode. 2. Rotate the left s...
Page 11
Ftm-350 s eries aprs ® m anual 11 p reparations s elect y our i con (u ser m ode ) when there is not an objective symbol in the available symbols, you may enter a symbol directly by the following procedures: 1. Press the [set] key to enter the set mode. 2. Rotate the left side [dial] knob to select ...
Page 12
Ftm-350 s eries aprs ® m anual 12 r eceiving an aprs ® b eacon g eneral 1. Set the “left” band to the aprs frequency. 144.390mhz is generally used in north america. If you don’t know the aprs frequency of your country, ask your dealer. Note: the factory default for aprs operation uses the “left” ban...
Page 13
Ftm-350 s eries aprs ® m anual 13 g eneral a dvice : you may change the aprs operating band via set mode item “e17 data band select” in the “aprs/pkt” group. You may change the baud rate of the aprs function via set mode item “e18 data speed” in the “aprs/pkt” group. You may specify the types of apr...
Page 14
Ftm-350 s eries aprs ® m anual 14 d isplay & s witches (r adio w indow ) press the [f] key repeatedly, until the [smart function] key category changes to the “f-3” mode, which is assigned to the functions necessary for aprs operation. Fwd bck set dial s list msg bcon b-tx ptt b f press the key: chan...
Page 15
Ftm-350 s eries aprs ® m anual 15 r eceiving an aprs ® b eacon d isplay & s witches (“aprs b eacon ” p op - up w indow ) when another stations aprs beacon is received, the aprs pop-up window opens, and the function of some keys will change as follows: a dvice : the aprs pop-up window closes automati...
Page 16
Ftm-350 s eries aprs ® m anual 16 d isplay & s witches (“s tation l ist ” w indow ) if necessary, press the [f] key repeatedly, until the [smart function] key’s category changes to “f-3” mode, then press the [s list] key to open the “station list” window. The ftm-350 series transceiver allows you to...
Page 17
Ftm-350 s eries aprs ® m anual 17 b eacon t ype d etails if necessary, press the [f] key repeatedly, until the [smart function] key’s category changes to “f-3” mode, then press the [s list] key to open the “station list” window. D isplay mic-e fixed fixed moving moving weather weather object object ...
Page 18
Ftm-350 s eries aprs ® m anual 18 left side dial bck set b tx del f b-1 disp b-1 text top b-1 reply b-1 qsy b-2 raw b-2 query b-2 gps rotate the left side dial knob to scroll through the received information (@ small “list” icon disap- pear) or select the received aprs station (@small “list” icon ap...
Page 19
Ftm-350 s eries aprs ® m anual 19 list number of the received aprs station. Symbol of the received aprs station 1 . Distance from the received aprs station. Direction to the received aprs station 2 . Callsign of the received aprs station. Beacon type of the received aprs station 3 . Altitude of the ...
Page 20
Ftm-350 s eries aprs ® m anual 20 list number of the received aprs station. Symbol of the received aprs station 1 . Distance from the received aprs station. Direction to the received aprs station 2 . Callsign of the received aprs station. Beacon type of the received aprs station. Tx output power of ...
Page 21
Ftm-350 s eries aprs ® m anual 21 list number of the received aprs station. Symbol of the received aprs station 1 . Distance from the received aprs station. Direction to the received aprs station 2 . Callsign of the received aprs station. Baecon type of the received aprs station. Communication range...
Page 22
Ftm-350 s eries aprs ® m anual 22 list number of the received aprs station. Symbol of the received aprs station 1 . Distance from the received aprs station. Direction to the received aprs station 2 . Callsign of the received aprs station. Beacon type of the received aprs station 3 . Speed of the rec...
Page 23
Ftm-350 s eries aprs ® m anual 23 list number of the received aprs station. Symbol of the received aprs station 1 . Distance from the received aprs station. Direction to the received aprs station 2 . Callsign of the received aprs station. Beacon type of the received aprs station 3 . Temperature. Rai...
Page 24
Ftm-350 s eries aprs ® m anual 24 list number of the received aprs station. Symbol of the received aprs station 1 . Distance from the received aprs station. Direction to the received aprs station 2 . Object name or item name. Beacon type of the received aprs station 3 . Callsign of the received aprs...
Page 25
Ftm-350 s eries aprs ® m anual 25 list number of the received aprs station. Direction to the received aprs station . Callsign of the received aprs station. Beacon type of the received aprs station. Time (or date) and the baud rate that a radio re- ceived an aprs station. Status comment of the receiv...
Page 26
Ftm-350 s eries aprs ® m anual 26 list number of the received aprs station. Distance from the received aprs station. Direction to the received aprs station 1 . Callsign of the received aprs station. Beacon type of the received aprs station. Speed of the received aprs station. Progression direction o...
Page 27
Ftm-350 s eries aprs ® m anual 27 list number of the received aprs station. Does not indicate the direction of the received aprs station. Callsign of the received aprs station. Beacon type of the received aprs station. Time (or date) and the baud rate that a radio re- ceived an aprs station. Status ...
Page 28
Ftm-350 s eries aprs ® m anual 28 s orting a “s tation l ist ” you may sort a “station list” temporarily. 1. If necessary, press the [f] key repeatedly, until the [smart function] key’s cat- egory changes to “f-2” mode. 2. Press the [s flt] key to open the set mode item “e35 sort filter”, then rotat...
Page 29
Ftm-350 s eries aprs ® m anual 29 aprs f ilter s etting the aprs filter option allows you to select the specific types of data to receive. 1. If necessary, press the [f] key repeatedly, until the [smart function] key’s cat- egory changes to “s-2” mode. 2. Press the [s flt] key to open the set mode i...
Page 30
Ftm-350 s eries aprs ® m anual 30 r eceiving an aprs ® b eacon c allsign r inger you may enable an alert ringer ( ) to sound when an aprs beacon is received from a specified station. Enter the callsign of the designated aprs beacon, via set mode item “e10 aprs ringer (call)”, in advance. 1. Press th...
Page 31
Ftm-350 s eries aprs ® m anual 31 r ange r inger you may enable a specific alert ringer ( ) to sound when an aprs beacon is received from a specified station that is within a selected range. Confirmation of whether the speci- fied station is within communication range is verified by a bell ringer. 1...
Page 32
Ftm-350 s eries aprs ® m anual 32 aprs n avigation you may navigate to a specific aprs station when the optional fgps-1 or fgps-2 gps antenna unit is installed. 1. If necessary, press the [f] key repeatedly, until the [smart function] key’s cat- egory changes to “f-3” mode, then press the [s list] k...
Page 33
Ftm-350 s eries aprs ® m anual 33 i ndicating the raw p acket d ata you may confirm the raw data of the received aprs beacon. 1. If necessary, press the [f] key repeatedly, until the [smart function] key’s cat- egory changes to “f-3” mode, then press the [s list] key to open the “station list” windo...
Page 34
Ftm-350 s eries aprs ® m anual 34 r eceiving an aprs ® b eacon d eleting a r eceived b eacon from the “s tation l ist ” f rom the “s tation l ist ” w indow 1. If necessary, press the [f] key repeatedly, until the [smart function] key’s cat- egory changes to “f-3” mode, then press the [s list] key to...
Page 35
Ftm-350 s eries aprs ® m anual 35 d eleting a r eceived b eacon from the “s tation l ist ” d eleting a ll r eceived b eacons from the “s tation l ist ” 1. If necessary, press the [f] key repeatedly, until the [smart function] key’s cat- egory changes to “f-3” mode, then press the [s list] key to ope...
Page 36
Ftm-350 s eries aprs ® m anual 36 t ransmit an aprs ® b eacon m anual t ransmission to transmit your aprs beacon manually, press the [b-tx] key on the “aprs station list” window or “aprs beacon detail” window. You may transmit your aprs beacon manually from the frequency display window. To do this, ...
Page 37
Ftm-350 s eries aprs ® m anual 37 a utomatic t ransmission the ftm-350 series transceiver allows you to transmit your aprs beacon automatically and repeatedly. 1. If necessary, press the [f] key repeatedly, until the [smart function] key cat- egory changes to “f-3” mode. 2. Press the [bcon] key repe...
Page 38
Ftm-350 s eries aprs ® m anual 38 t ransmit an aprs ® b eacon o ptional s ettings i nterval t ime s etting for a utomatic t ransmission you may set the interval time to transmit an aprs beacon automatically when the “auto” beacon mode is set to “on (“ ” icon appears)”. 1. Press the [set] key to ente...
Page 39
Ftm-350 s eries aprs ® m anual 39 t ransmit an aprs ® b eacon o ptional s ettings smartbeaconing tm s ettings the transceiver set mode item “e34 smartbeaconing” is set to “type1” as default, this setting is suitable for mobile operation. We recommend using this default setting. 1. Press the [set] ke...
Page 40
Ftm-350 s eries aprs ® m anual 40 t ransmit an aprs ® b eacon o ptional s ettings s tatus t ext you may store five status text messages (up to 60 characters for each memory), and you may transmit one of these status text messages with the aprs beacon. 1. Press the [set] key to enter the set mode. 2....
Page 41
Ftm-350 s eries aprs ® m anual 41 t ransmit an aprs ® b eacon 8. Rotate the left side [dial] knob to select “1: select” item, then press the left side [dial] knob. 9. Rotate the left side [dial] knob to select the status text register (“text 1” through “text 5”) you wish to send, then press the left...
Page 42
Ftm-350 s eries aprs ® m anual 42 o ptional s ettings p osition c omment this column selects the “position comment” (fixed form message) which is included in the aprs beacon. 1. Press the [set] key to enter the set mode. 2. Rotate the left side [dial] knob to select “aprs/pkt” group, then press the ...
Page 43
Ftm-350 s eries aprs ® m anual 43 o ptional s ettings d igipeater r oute the ftm-350 series transceiver allows you to set up to eight digipeaters for the aprs packet path. The ftm-350 series transceiver is preset to “wide1-1” and “wide1-1, wide2-1” digi- path to insure that your transmitted aprs bea...
Page 44
Ftm-350 s eries aprs ® m anual 44 o ptional s ettings d igipeater r oute (a ddress s etting ) when selecting a path route (path 1 - path 4, full 1, or full 2) on set mode item “e20 digi path select”, you must input the callsign or alias of that digipeater via set mode items “e21 digi path 1” - “e24 ...
Page 45
Ftm-350 s eries aprs ® m anual 45 t ransmit an aprs ® b eacon n ote.
Page 46
Ftm-350 s eries aprs ® m anual 46 g eneral when an aprs message is received, the “aprs message” pop-up window opens and an aprs alert beep ( ) is heard. The “aprs message” pop-up window closes automati- cally after ten seconds. A dvice : the “aprs message” pop-up window closes automatically after te...
Page 47
Ftm-350 s eries aprs ® m anual 47 r eceiving an aprs ® m essage d isplay & s witches if necessary, press the [f] key repeatedly, until the [smart function] key’s category changes to “f-3” mode, then press the [msg] key to open the “message list” window. The ftm-350 series transceiver enables you to ...
Page 48
Ftm-350 s eries aprs ® m anual 48 list number rx / tx station name message type message number date / time message text indicates the list number of the received / transmitted aprs message. Rx: indicates the received aprs message. Tx: indicates the transmitted aprs message and indicates its remainin...
Page 49
Ftm-350 s eries aprs ® m anual 49 bck set dial m-1 re tx m-2 raw m-1 reply m-2 query m-1 m edit m-2 pos snd del f dial close the “message list” window. Access the set mode (aprs/pkt group). Press this knob (a small “list” icon appears at the bottom left of the display), then rotate this knob to sele...
Page 50
Ftm-350 s eries aprs ® m anual 50 m essage g roup s ettings the message group option allows you to choose to receive only specific types of message information. 1. Press the [set] key to enter the set mode. 2. Rotate the left side [dial] knob to select “aprs/pkt” group, then press the left side [dia...
Page 51
Ftm-350 s eries aprs ® m anual 51 r eceiving an aprs ® m essage d eleting a r eceived m essage from the “m essage l ist ” f rom the “m essage l ist ” w indow 1. If necessary, press the [f] key repeatedly, until the [smart function] key cat- egory changes to “f-3” mode, then press the [msg] key to op...
Page 52
Ftm-350 s eries aprs ® m anual 52 d eleting a r eceived m essage from the “m essage l ist ” d eleting a ll r eceived m essages from the “m essage l ist ” 1. If necessary, press the [f] key repeatedly, until the [smart function] key cat- egory changes to “f-3” mode, then press the [msg] key to open t...
Page 53
Ftm-350 s eries aprs ® m anual 53 r eceiving an aprs ® m essage n ote.
Page 54
Ftm-350 s eries aprs ® m anual 54 t ransmit an aprs ® m essage g eneral 1. If necessary, press the [f] key repeatedly, until the [smart function] key cat- egory changes to “f-3” mode. 2. Press the [msg] key to open the “message list” window. 3. Press the [f] key, if needed, to change the [smart func...
Page 55
Ftm-350 s eries aprs ® m anual 55 t ransmit an aprs ® m essage 9. Enter the message using the same procedures as described previously. Additionally, you may select/add/delete the characters/message using the following procedure: a. Press the [font] key to change the character (upper-case alphabet, l...
Page 56
Ftm-350 s eries aprs ® m anual 56 r eceiving an a cknowledgment the aprs message is transmitted repeatedly, up to five times, once each minute until an acknowledgment packet (“ack”) is received. If an acknowledgment packet (“ack”) is re- ceived, the beeper will sound and the “ ” icon will appear on ...
Page 57
Ftm-350 s eries aprs ® m anual 57 s tore a f ixed f orm m essage the ftm-350 series transceiver allows you to store eight fixed form messages (up to 16 characters for each message). 1. Press the [set] key to enter the set mode. 2. Rotate the left side [dial] knob to select “aprs/pkt” group, then pre...
Page 58
Ftm-350 s eries aprs ® m anual 58 t ransmit an aprs ® m essage aprs m essage r eplying you may reply to another stations received massage manually. To do this: 1. If necessary, press the [f] key repeatedly, until the [smart function] keys cat- egory changes to “f-3” mode. 2. Press the [msg] key to o...
Page 59
Ftm-350 s eries aprs ® m anual 59 aprs m essage r eplying a utomatic m essage r eplying you may transmit a reply message which was programmed beforehand automatically when the transceiver receives a message (factory default: the transceiver transmits reply to all received messages). 1. Press the [se...
Page 60
Ftm-350 s eries aprs ® m anual 60 s et m ode i tem e01 aprs compass e02 aprs destination e03 aprs filter e04 aprs message txt e05 aprs modem e06 aprs mute e07 aprs popup e08 aprs popup color a vailable v alues (d efault : b old ) north up / heading up apy350 (fixed) 1 mic-e: on / off 2 position: on ...
Page 61
Ftm-350 s eries aprs ® m anual 61 a vailable v alues (d efault : b old ) 1 tx beacon: on / off 2 tx message: on / off 3 rx beacon: on / off 4 rx message: on / off 5 my packet: on / off 6 call ringer: on / off 7 rng ringer: off / 1 ~ 100 8 msg voice: on / off 8 stations (6 characters plus ssid) 100ms...
Page 62
Ftm-350 s eries aprs ® m anual 62 s et m ode i tem e16 com port setting e17 data band select e18 data speed e19 data squelch e20 digi path select e21 digi path 1 e22 digi path 2 e23 digi path 3 e24 digi path 4 e25 digi path full 1 e26 digi path full 2 e27 message group e28 message reply e29 my calls...
Page 63
Ftm-350 s eries aprs ® m anual 63 s et m ode i tem e30 my position set e31 my position e32 my symbol e33 position comment e34 smartbeaconing e35 sort filter e36 voice alert f unction select your position to send by aprs. Determine and memorize your location (lat/log). Selects your icon which will be...
Page 64
Ftm-350 s eries aprs ® m anual 64 e01: aprs compass function: selects the display format of the aprs compass. Available values: north up or heading up default: north up north up: the lcd displays the compass scale in the “north up” orientation and displays the beacon station with a “d” icon on the c...
Page 65
Ftm-350 s eries aprs ® m anual 65 object: when this item is set to “on”, the transceiver shows the stations which send an object beacon. Item: when this item is set to “on”, the transceiver shows the stations which send an item beacon. Status: when this item is set to “on”, the transceiver shows the...
Page 66
Ftm-350 s eries aprs ® m anual 66 beacon: selects the open time of the pop-up window, when an aprs beacon is received for the first time or when an aprs beacon which includes different content is received. : it usually shows whenever the status text of your aprs beacon is changed. However the ftm-35...
Page 67
Ftm-350 s eries aprs ® m anual 67 6 message: off, lcd color, wht(white)-blue, sky- blue, mrn(marine)-blue, green, ylw(yellow)- green, orange, amber, or white 7 grp/bult: off, lcd color, wht(white)-blue, sky- blue, mrn(marine)-blue, green, ylw(yellow)- green, orange, amber, or white 8 my pkt: off, lc...
Page 68
Ftm-350 s eries aprs ® m anual 68 5 my packet: off or on 6 call ringer: off or on 7 rng ringer: off/1 - 100 8 msg voice: off or on default: 1 tx beacon: on 2 tx message: on 3 rx beacon: on 4 rx message: on 5 my packet: on 6 call ringer: off 7 rng ringer: off 8 msg voice: off tx beacon: when this ite...
Page 69
Ftm-350 s eries aprs ® m anual 69 e10: aprs ringer (call) function: programs the callsigns, which causes a ringing bell sound when the “5 call ringer” function of the set mode item “e08 aprs ringer” is set to on. You may program up to eight callsigns. E11: aprs txdelay function: selects the transmis...
Page 70
Ftm-350 s eries aprs ® m anual 70 e14: beacon status txt function: enables/disables the transmission of the status text and programs its programmed. Available values: 1 select: off, text 1 ~ text 5 2 tx rate: 1/1 ~ 1/8, 1/2(freq) ~ 1/8(freq) 3 text 1: 4 text 2: 5 text 3: 6 text 4: 7 text 5: default:...
Page 71
Ftm-350 s eries aprs ® m anual 71 default: 1 auto: off 2 interval: 5min 3 proportional: on 4 decay: on 5 low speed: 3 6 rate limit: 30 sec auto: this item selects the automatic transmission method of the aprs bea- con. When this item is set to “off” (no icon), your aprs beacon does not transmit auto...
Page 72
Ftm-350 s eries aprs ® m anual 72 vehicle is stopped the interval time extends to “2 min” “3 min” “5 min” “10min” “15min” “20min” “30min” “30min” ... (the “60min” is not selected). When the “interval” item is set to “30min” or “60min”, this item is ignored. Low speed: this item determines the thresh...
Page 73
Ftm-350 s eries aprs ® m anual 73 when this item is set to “gps out”, the transceiver outputs the gps data (nmea data: gga & rmc) from the com port. When this item is set to “packet”, the transceiver outputs the packet data from the com port. When this item is set to “waypoint”, the transceiver outp...
Page 74
Ftm-350 s eries aprs ® m anual 74 aprs/pkt s et m ode e19: data squelch function: configures the squelch settings for aprs, data, and tx. Available values: 1 aprs: rx band or tx/rx band 2 data: rx band or tx/rx band 3 tx: off or on default: 1 aprs: rx band 2 data: rx band 3 tx: on rx band: does not ...
Page 75
Ftm-350 s eries aprs ® m anual 75 e25: digi path full 1 function: sets the aprs packet path. Program the address information (callsign or alias etc) of the digipeater that you selected as “full 1” in set mode item “e20 digi path select” (8 path). E26: digi path full 2 function: sets the aprs packet ...
Page 76
Ftm-350 s eries aprs ® m anual 76 e30: my position set function: determines your location (longitude/latitude). Available values: gps, manual, or p.List grp1-point1 ~ p.List grp4-point4 default: gps gps: your location is determined by the optional gps unit. When the op- tional gps unit is connected ...
Page 77
Ftm-350 s eries aprs ® m anual 77 e34: smartbeaconing function: selects the various parameters of smartbeaconing tm . The smartbeaconing tm function regulates the aprs beacon trans- missions based on the received gps data (movement speed, and move- ment direction etc.). Available values: 1 status: o...
Page 78
Ftm-350 s eries aprs ® m anual 78 fast rate: this item designates the maximum transmission interval time of the aprs beacon at high vehicle speeds. Turn angle: this item designates the course change angle that indicates a progress heading change. Turn slope: this item sets a coefficient to modify th...
Page 79
Ftm-350 s eries aprs ® m anual 79 object/item: only the aprs beacons from object or item stations are displayed. Digipeater : only the aprs beacons from digipeaters are displayed. Voip: only the aprs beacons from a voip station, such as wires stations are displayed. Weather: only the aprs beacons fr...
Page 80
Ftm-350 s eries aprs ® m anual 80 squelch operation, and aprs communication is no tone operation. A blinking “tsq” icon will appear on the display except aprs trans- mission. When this item is set to “rx-dcs”, voice communication is dcs (digital code squelch) operation, and aprs communication is no ...
Page 81
Ftm-350 s eries aprs ® m anual 81 emergency comment set x 3 times emergency beacon received x 12 times beacon received (aprs filter “on”) beacon received (aprs filter “off”) beacon received (range ringer station) beacon received (callsign ringer station) own message received message ack received mes...
Page 82
Ftm-350 s eries aprs ® m anual 82 8-p in mini din pkd (packet data input) gnd pks (ptt) rx96 (9600bps packet data output) rx12 (1200bps packet data output) sql (squelch control) txd (serial data output: transceiver pc) rxd (serial data input: transceiever pc) a ppendix d-sub 9-p in n.C. Txd (serial ...
Page 83
Ftm-350 s eries aprs ® m anual 83 a ppendix ct-142 c able c onnections 8-p in mini din pkd (packet data input) gnd pks (ptt) rx96 (9600bps packet data output) rx12 (1200bps packet data output) sql (squelch control) txd (serial data output: transceiver pc) rxd (serial data input: transceiver pc) d-su...
Page 84
Ftm-350 s eries aprs ® m anual 84 printed in japan copyright 2011 vertex standard co., ltd. All rights reserved. No portion of this manual may be reproduced without the permission of vertex standard co., ltd. E h 0 3 3 m 1 1 4.