Yaesu RF UTUNING KIT Installation Manual - page 2
4. Affix the Model Plate to the recessed area on the Top Case,
and then connect the Top Case to the μ-TUNE-UNIT with four
Screws (Screw B: M3x8).
2. Attach the four Legs to the back side of the Main Frame with
four Screws (Screw D: M4x16).
3. Attach the Side Case F and Side Case B to the Top Case with
eight Screws (Screw C: M4x6).
5. Attach the μ-TUNE-UNIT (which was assembled in step 4) to
the Main Frame (which was assembled in step 2) with two
Screws (Screw B: M3X8).
6. Attach the Bottom Case to the Main Frame with four Screws
(Screw B: M3X8).
1. Attach the Spacer S to the back side of the Main Frame with
four Screws (Screw A: M3x6). There are non-painted areas on
the back side.
Main Frame
Spacer S
Screw A
Leg
Screw D
Top Case
Side Case F
Side Case B
Screw C
Screw C
Screw B
7. Place the Main Frame upside down. Attach the RX-TUNE-
UNIT to the Main Frame with the two Long Spacers (Spacer
L) and two Screws (Screw E: M3X6 Screw with washer).
Screw B
Bottom Case
8. Connect the TMP Connector (Orange) to J1006 on the RX-
TUNE-UNIT and connect the TMP Connector (Green) to J1010
on the RX-TUNE-UNIT, then connect the Flat Cable to J1007
on the RX-TUNE-UNIT.
Note: 1) insure that the Flat Cable is inserted into connec-
tor J1007 squarely. If the Flat Cable is inserted di-
agonally, the contacts could short and cause damage.
2) Please be careful handling the Flat Cable. Sharp
bends will break the conductors and cause open or
intermittent connections.
9. Confirm the μ-TUNE-UNIT Model Number (for example:
MTU-80/40), and then insert the Jumper Plug into the corre-
sponding labeled Jumper connector on the RX-TUNE-UNIT.
For example, if your μ-TUNE-UNIT is MTU-80/40, insert the
Jumper Plug to the J1004 that is labeled MTU-80/40.
Important Note: Please confirm Jumper connection again,
because the wrong connection will cause malfunction of the
unit. If you turned on the RF μTUNING KIT with wrong con-
nections, turn the power off and connect the Jumper Plug cor-
rectly.
10. Affix the Shield Cover L to the RX-TUNE-UNIT with two
Screws (Screw A: M3X6). Next, attach the Shield Cover S
with two Screws (Screw A: M3X6). Be very careful not to
pinch any wires.
μ-TUNE-UNIT
Model Plate
Screw B
Flat Cable
TMP Connector (Green)
TMP Connector (Orange)
J1010
J1007
J1006
J1010
Connect the TMP Connector (Green)
J1006
Connect the TMP Connector (Orange)
J1007
Connect the Flat Cable
J1007
J1007
J1003
for MTU-160
J1004
for MTU-80/40
J1005
for MTU-30/20
Jumper Plug
J1004
MTU-80/40
11. Installation is completed.
12. Double check all connections and the wiring, then connect the
RF μTUNING KIT to the FT-2000, as is described in the “In-
terconnections” chapter in the RF μTUNING KIT Operating
Manual.
Screw A
Screw A
Shield Cover L
Shield Cover S
I
NSTALLATION
Screw E
Spacer L
Main Frame
RX-TUNE-UNIT