- DL manuals
- Yale
- Security System
- HSA3400
- Installation, Programming, Operating
Yale HSA3400 Installation, Programming, Operating
Summary of HSA3400
Page 1
Hsa3400 keypad alarm system installation programming operating keep in a handy place for reference and for future maintenance helpline 01902 635998 www.Ukpanels.Com.
Page 2
2 introduction general system overview thank you for choosing the yale hsa3400 security alarm system. This simple to install system has been designed with the user in mind. The siren has a sounder and strobe leds to attract attention. In addition, two window stickers are included in the pack. Please...
Page 3
3 contents contents 1 location planning 4-5 2 insert the batteries 6-7 3 program the siren and keypad 8-9 4 mounting the siren and keypad 10 5 programming and mounting detectors 11 6 using the system 13 installing and using accessories 14 changing the batteries 16 specifications 18 trouble shooting ...
Page 4
Location planning work out the best places to locate the devices for maximum protection. Having chosen the locations operating range all devices must be within 30 metres of the siren unit and must not be mounted on or near large metal objects. Avoid obvious sources of electrical interference such as...
Page 5
S do not mount at this stage . 5 extend the system extend the system in the future to increase your security or as your needs change. For example, add extra pir detectors in bedrooms and extra door/window contacts. Keyfob remote control accessory can be used outside the premises and kept on your key...
Page 6
Pir movement detectors remove the fixing screw and cover assembly and insert the three aa batteries as shown. • the light steadily flashes for 30 seconds while components initialise. 6 + + + unpack all the parts on a table top the easiest way to get to know the system and get it up and running quick...
Page 7
Door/window contacts 1 remove the cover of each door/window contact by loosening the fixing screw. 2 insert two aaa batteries into each detector as shown. The indicator led will flash briefly. 7 keypad remote control remove the cover and insert the 3 aaa alkaline batteries as shown. The ‘tx’ led wil...
Page 8
3 8 program the siren and keypad the siren is the heart of the system. First, teach the siren to recognise (learn) the keypad. Jumper in ‘off’ ‘parked’ position jumper in ‘on’ position use of jumper switches the siren, pir and door/window contact each have internal switches, or ‘jumpers’, which cont...
Page 9
Further siren programming the siren can be configured to your personal requirements by the use of jumpers. Jumper positions j7 on = jamming detection ‘off’; off = jamming detection ‘on’ j6 on = normal, j6 off = clear memory j5 on = stand alone operation; off = slave operation, not used in this syste...
Page 10
10 mounting the siren and keypad warning before mounting the keypad and siren ensure that the system tamper is disabled as described below. 4 disabling the system tamper before mounting it is important to disable the tamper to avoid the siren sounding an alarm. 1 enter 0000 then press test. The ‘tx’...
Page 11
Learning in pirs and door/window contacts to learn pirs and door/windows contacts into the system follow the steps below. 1 enter 0000, then press test. The ‘tx’ led will flash showing the keypad is in program mode. 2 disable tamper by pressing test then 2. The keypad will beep and the siren confirm...
Page 12
• when the jumper is in the normal ‘off’ position the indicator light will normally be off. It will only light if there is a problem, either a low battery or a tamper condition. • ensure the jumper is in the normal ‘off’ position when testing is finished, otherwise low battery and tamper conditions ...
Page 13
13 setting or changing your user pin code 1 put the keypad into program mode by entering the 0000 default code and pressing test. 2 enter 0000 then clr, enter your new 4 digit pin code and press prog, the keypad will beep to confirm. 3 press off twice on the keypad to exit the program mode. • if the...
Page 14
14 adding accessories to provide additional protection you can add extra door/window contacts, pirs, keyfob remote controls, keypad remote controls, help buttons and smoke detectors. These are available separately from your local stockist. Putting the system in and out of learn mode put the system i...
Page 15
15 adding the help button program your help button before installation and test in the desired location before mounting. Programming 1 follow sections 1 and 3 (inserting batteries and location planning). 2 with the system in learn mode, press and hold the red button on the help button – the led will...
Page 16
16 changing the batteries always use alkaline batteries as replacements, any other type of battery (such as heavy duty) can cause problems with the operation of the system. Typical life of siren batteries is two years, whilst detectors will operate for three years before batteries need changing. Alw...
Page 17
17 model: hsa3400 hsa3020 hsa3060 hsa3010 hsa3050 hsa3045 hsa3080 hsa3030 hsa3070 www.Ukpanels.Com.
Page 18
18 specifications all devices emc tested to ets 300 683 radio components tested to en 300 220-1 environmental conditions -10°c to 40°c, relative humidity 70% non-condensing for all units except the external siren. Siren: -20°c to 50°c, relative humidity 95% non- condensing radio operational range 30...
Page 19
19 trouble shooting siren siren does not respond to keypad • keypad low battery or bad connection. Check battery connections and polarity, if ok replace battery with alkaline equivalent. • siren batteries are completely exhausted. Check siren batteries by removing siren cover, if there is no tamper ...
Page 20: Key Points
Key points stopping the alarm • enter your pin code and press off on the keypad • press disarm on the keyfob accessory (if purchased) if any of the devices beep or flash, they have either been tampered with see trouble-shooting, page 19 or require a new battery see how to change a battery, page 16 w...