- DL manuals
- Yamaha
- Outboard Motor
- 15C
- Owner's Manual
Yamaha 15C Owner's Manual
Summary of 15C
Page 1
Printed in japan march 2003-0.5 × 1 ! 63v-28199-16 (9.9fmh, 15fmh) (e) printed on recycled paper 9.9c 15c owner’s manual u.S.A.Edition lit-18626-05-34 63v-9-16 hyoshi 2/18/03 13:52 page 1.
Page 2
63v-9-16 hyoshi 2/18/03 13:52 page 2.
Page 3: To The Owner
Thank you for choosing a yamaha out- board motor. This owner’s manual con- tains information needed for proper oper- ation, maintenance and care. A thorough understanding of these simple instruc- tions will help you obtain maximum enjoyment from your new yamaha. If you have any question about the op...
Page 4: General Information
General information basic components operation maintenance trouble recovery index contents read this owner’s manual carefully before operating your outboard motor. E 1 2 3 4 5 6 63v-9-16-1 2/18/03 13:56 page 3.
Page 5: Chapter 1
E 2 3 4 5 6 emb00010 chapter 1 general information identification numbers record ....................................................1-1 outboard motor serial number...........1-1 emission control information...1-2 safety information..........................1-3 important labels .......................
Page 6: Identification Numbers
1-1 e emu00005 identification numbers record emu00007 outboard motor serial number the outboard motor serial number is stamped on the label attached to the port side of the clamp-bracket. Record your outboard motor serial num- ber in the spaces provided to assist you in ordering spare parts from you...
Page 7: Emission Control
1-2 e q w 108015* emu01385 emission control information emu01386 north american models this engine conforms to u.S. Environ- mental protection agency (epa) regula- tions for marine si engines. See the label affixed to your engine for details. Approval label of emission control certificate this label...
Page 8: Safety
1-3 e 8 this product emits exhaust gases which contain carbon monoxide, a colorless, odorless gas which may cause brain damage or death when inhaled. Symp- toms include nausea, dizziness, and drowsiness. Keep cockpit and cabin areas well ventilated. Avoid blocking exhaust outlets. 8 check throttle, ...
Page 9
1-4 e 8 be informed about boating safety. Addi- tional publications and information can be obtained from many organizations, including the following: united states coast guard consumer affairs staff (g-bc) office of boating, public, and consumer affairs u.S. Coast guard headquarters washington, d.C....
Page 10: Important Labels
1-5 e emb30010 important labels warning labels 1 2 202012* q w warning this engine is equipped with a neutral starting device. The engine will not start unless the shift control is in neutral position. 6e0-83627-41 warning ●be sure shift control is in neutral before starting engine. (except 2hp) ●do...
Page 11: Basic Boating Rules
1-6 e stand-on vessel the vessel with the right-of-way has the duty to continue its course and speed, except to avoid an immediate collision. When you maintain your direction and speed, the other vessel will be able to determine how best to avoid you. Give-way vessel the vessel which does not have t...
Page 12
1-7 e side. This rule doesn’t apply if both of you will clear one another if you continue on your set course and speed. Crossing when two power driven vessels are crossing each other’s path close enough to run the risk of collision, the vessel which has the other on the starboard (right) side must k...
Page 13
1-8 e 1. When the sailing vessel is overtaking the power-driven vessel, the power- driven vessel has the right-of-way. 2. Sailing vessels should keep clear of any fishing vessel. 3. In a narrow channel, a sailing vessel should not hamper the safe passage of a power-driven vessel which can navigate o...
Page 14
1-9 e remember, markings may vary by geo- graphic location. Always consult local boating authorities before driving your boat in unfamiliar waters. 1 1 a 1 1 proceeding toward head of navigation from seaward can buoy odd number. Leave to port. Or secondary channel buoys starts new numbering system o...
Page 15: Fueling Instructions
1-10 e emu00016 fueling instructions w gasoline and its vapors are high- ly flammable and explosive! 8 do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition. 8 stop engine before refueling. 8 refuel in a well-ventilated area. Refuel portable fuel tanks off the ...
Page 16
1-11 e emu00027 gasohol there are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used if ethanol content does not exceed 10% and the fuel meets minimum octane ratings. Gasohol containing methanol is not recommended by yama- ha because...
Page 17: Propeller Selection
1-12 e emu01395 propeller selection the performance of your outboard motor will be critically affected by your choice of propeller, as an incorrect choice could adversely affect performance and could also seriously damage the motor. Engine speed depends on the propeller size and boat load. If engine...
Page 18: Start-In-Gear Protection
1-13 e note: at full throttle and under a maximum boat load, the engine’s rpm should be within the upper half of the full throttle operating range, as listed in “specifica- tions” on page 4-1. Select a propeller which fulfills this requirement. If operating under conditions which allow the engine’s ...
Page 19: Chapter 2
Emc00010 chapter 2 basic components main components..............................2-1 operations of controls and other functions ................................2-2 fuel tank ................................................2-2 gear shift lever .....................................2-2 engine stop butt...
Page 20: Main Components
2-1 e 101022* 902063 902051* !9 !8 101232 !2 !1 !3 !5 !4 !6 u o y i !0 t !7 q w e r emu01206 main components 1 top cowling 2 cowling lock lever 3 cooling water pilot hole 4 tilt lock lever 5 recoil starter handle 6 gear shift lever 7 throttle control grip 8 throttle friction adjustment knob 9 engine...
Page 21: Operations of Controls
2-2 e q w r 902051 e emc20010 operations of controls and other functions emc21012 fuel tank if your model was equipped with a portable fuel tank, its function is as fol- lows. 1 fuel hose joint 2 fuel meter(if equipped) 3 fuel tank cap 4 air vent screw(if equipped) fuel hose joint this connector is ...
Page 22
2-3 e emc27011 engine stop button (for tiller control model) pushing this button opens the ignition cir- cuit and stops the engine. 407021* 407021 q w emu00931 engine stop lanyard switch (for tiller control model) the lock-plate 1 must be attached to the engine stop lanyard switch for the engine to ...
Page 23
2-4 e emc40010 throttle control grip (for tiller control model) the throttle control grip is on the tiller handle. Turn the grip counterclockwise to increase speed and clockwise to decrease speed. 503013 q 305071 1 2 3 4 209011 throttle indicator the fuel consumption curve on the throt- tle indicato...
Page 24
2-5 e 503015 502011 emc60010 tiller handle (for tiller control model) moving the tiller handle sideways to adjust the steering direction. Emc64010 throttle friction adjustment (for tiller control model) a friction device in the tiller handle pro- vides resistance to movement of the throttle grip. Th...
Page 25
2-6 e 408011 001742 emd00010 steering friction adjustment (for tiller control model) a friction device provides resistance to steering movement. This is adjustable for operator preference. An adjusting screw/bolt is located on the swivel bracket. To increase the resistance: turn the adjusting screw/...
Page 26
Emd68010* carrying handle the carrying handle is included between the clamp bracket. The carrying handle enables you to carry the outboard motor readily with one hand after setting it up. To set up the carrying handle, proceed as follows. 1) place the tilt lock lever in the lock position. 2) securel...
Page 27: Chapter 3
Emf00010 chapter 3 operation installation ........................................3-1 mounting the outboard motor............3-2 clamping the outboard motor ............3-4 filling fuel and engine oil ............3-5 filling fuel..............................................3-5 gasoline (petrol) and...
Page 28: Installation
3-1 e emf10010 installation c c incorrect engine height or obstructions to smooth water flow (such as the design or condition of the boat or accessories such as transom ladders/depth finder trans- ducers) can create airborne water spray while the boat is cruising. Severe engine damage may result if ...
Page 29
3-2 e emu00176 mounting the outboard motor w improper mounting of the outboard motor could result in hazardous condi- tions such as poor handling, loss of con- trol, or fire hazards. Observe the follow- ing: 8 the information presented in this sec- tion is intended as reference only. It is not possi...
Page 30
3-3 e w overpowering a boat may cause severe instability. Do not install an outboard motor with more horsepower than the maximum rating on the capacity plate of the boat. If the boat does not have a capacity plate, consult the boat manufac- turer. 104013 0~25mm emu01298 mounting height to run your b...
Page 31
3-4 e emf14010 clamping the outboard motor 1) place the outboard on the transom so that it is positioned as close to the center as possible. Tighten the tran- som clamp screws evenly and secure- ly. Check the clamp-screws for tight- ness occasionally during operation of the motor as they can work lo...
Page 32: Filling Fuel
3-5 e filling fuel and engine oil emf30010 filling fuel 1) remove the fuel tank cap. 2) fill the fuel tank carefully. 3) close the cap securely after refueling. Wipe up any spilled fuel. Ring free fuel additive gasoline is a precise blend of many differ- ent substances, each chosen to give cer- tain...
Page 33
3-6 e emf35010 gasoline (petrol) and oil mixing pre-mix model 1) pour oil and gasoline into the fuel tank, in that order. 1 oil 2 gasoline (petrol) 2) then mix the fuel thoroughly by shak- ing. 3) make sure the oil is mixed with gaso- line . C c 8 avoid using any oil other than the des- ignated type...
Page 34: Pre-Operation Checks
3-7 e note: if using a permanently installed tank, pour the oil gradually as the fuel is being added to the tank. Mixing ratio 100 : 1 gasoline (petrol) engine oil 0.01 l 0.12 l 0.14 l 0.24 l (0.01 us qt, (0.13 us qt, (0.15 us qt, (0.25 us qt, 0.01 imp qt) 0.11 imp qt) 0.12 imp qt) 0.21 imp qt) 1 l ...
Page 35: Breaking In (Running In)
3-8 e emf43010 controls 8 check throttle, shift, and steering for proper operation before starting the engine. 8 the controls should work smoothly, without binding or unusual free play. 8 look for loose or damaged connec- tions. 8 check operation of the starter and stop switches when the outboard mo...
Page 36
3-9 e emu00226 run the engine under load (in gear with a propeller installed) as follows. 1) first 10 minutes: run the engine at the lowest possi- ble-speed. A fast idle in neutral is best. 2) next 50 minutes: do not exceed half throttle (approxi- mately 3,000 r/min). Vary engine speed occasionally....
Page 37: Starting Engine
3-10 e emu01147 starting engine w 8 before starting the engine, make sure that the boat is tightly moored and that you can steer clear of any obstructions. Be sure there are no swimmers in the water near you. 8 when the air vent screw is loosened, gasoline (petrol) vapor will be released. Gasoline (...
Page 38
3-11 e emu01497 procedure for tiller control model 4) place the gear-shift lever in the neu- tral position. Note: the start-in-gear protection device pre- vents the engine from starting except when in neutral. 406042 n 503016 001105 5) attach the engine stop switch lanyard to a secure place on your ...
Page 39
3-12 e emu00241* manual start model 7) pull out the choke knob completely when the engine is cold. After the engine starts, set the choke knob to the 2nd or 3rd position for warming up the cold engine. After warming up the engine, set the choke knob to the original position. Note: 8 it is not necess...
Page 40: Warming Up Engine
Emg00010-* warming up engine 1) before beginning operation, allow the engine to warm up at idling speed for 3 minutes. (failure to do this will shorten engine life.) 2) check for a steady flow of water from the cooling-water pilot hole. C c a continuous flow of water from the pilot hole shows that t...
Page 41: Shifting
3-14 e emg20111 shifting w before shifting, make sure there are no swimmers or obstacles in the water near you. C c to change the shifting position from for- ward to reverse or vice-versa, close the throttle first so that the engine idles (or runs at low speeds). Emg22110 forward 1) place the thrott...
Page 42
3-15 e emg33210 reverse w when operating in reverse, go slowly. Do not open the throttle more than half. Oth- erwise, the boat may become unstable, which could result in loss of control and an accident. 1) place the throttle control grip in the fully closed position (for tiller control model). 2) ch...
Page 43: Stopping Engine
3-16 e emg38010 stopping engine let it cool off for a few minutes at idle or low speed first. Stopping the engine immediately after operating at high speed is not recommended. Emu00275 1) push and hold the engine stop button until the engine comes to a complete stop. 2) after stopping the engine, di...
Page 44: Trimming Outboard
Emu01412 trimming outboard motor the trim angle of the outboard motor helps determine the position of the bow of the boat in the water. The correct trim angle will help improve performance and fuel economy while reducing strain on the engine. The correct trim angle depends upon the combination of bo...
Page 45
3-18 e emu00951 manual tilt model there are 4 or 5 holes provided in the clamp bracket to adjust the outboard motor trim angle. 1) stop the engine. 2) remove the trim angle adjusting rod 1 from the clamp bracket while tilting the motor up slightly. 3) reposition the rod in the desired hole. To raise...
Page 46
Emu19160 trim angle settings and boat handling when the boat is on plane, a bow-up atti- tude results in less drag, greater stability and efficiency. This is generally when the keel line of the boat is up about 3 to 5 degrees. With the bow up, the boat may have a greater tendency to steer to one sid...
Page 47: Cruising In Shallow
3-20 e emg70011 cruising in shallow water the outboard motor can be tilted up par- tially to allow operation in shallow water. W 8 place the gear shift in the neutral posi- tion before using the shallow water cruising system. 8 run the boat at the lowest possible speed when using the shallow water c...
Page 48
3-21 e emg71210 procedure 1) place the gear shift lever in the neu- tral position. 2) pull up the tilt lock lever. 3) slightly tilt up the engine. The tilt- support bar will lock automatically, supporting the engine in a partially raised position. Note: if the engine is tilted up completely, the til...
Page 49: Tilting Up/down
3-22 e emh10110 tilting up/down if the engine will be stopped for some time, or if the boat is moored in shallows, the engine should be tilted up to protect the propeller and casing from damage by collision with obstructions, and also to reduce salt corrosion. C c 8 before tilting the motor, follow ...
Page 50
3-23 e emu00290 procedure for tilting up 1) place the gear shift lever in neutral. 2) remove the fuel line connection from the motor. 3) place the tilt lock lever in the release position. Emu00300 procedure for tilting down 1) place the tilt lock lever in the lock position. 2) slightly tilt up the e...
Page 51: Cruising In Other
3-24 e emh60010 cruising in other conditions cruising in salt water after operating in salt water, wash out the cooling-water passages with fresh water to prevent them from becoming clogged- up with salt deposits. Note: refer to cooling system flushing instruc- tions in “transporting and storing out...
Page 52: -Memo-
E -memo- 63v-9-16-3 2/18/03 14:04 page 26.
Page 53: Chapter 4
Emk00010 chapter 4 maintenance specifications .....................................4-1 transporting and storing outboard motor ...............................4-3 trailering outboard motor...................4-3 storing outboard motor ......................4-4 periodic maintenance........................
Page 54: Specifications
4-1 e emr50302* specifications 25 (2.5, 18) 17 (1.7, 12) 8spark plug n•m (kgf•m, lb•ft) 8propeller nut n•m (kgf•m, lb•ft) model unit 9.9mshc item dimensions performance 8overall length mm (in.) 8overall height s mm (in.) 8overall width mm (in.) 8transom height s mm (in.) 8weight s kg (lb.) 873 (34.4...
Page 55
4-2 e 15mshc — — 873 (34.4) 1,040 (40.9) 332 (13.1) 440 (17.3) 36 (79) 4,500~5,500 11.0 (15) at 5,000 r/min. 700~800 2-stroke, l2 246 (15.01) 56 × 50 (2.20 × 1.97) c.D.I b7hs-10 0.9~1.0 (0.035~0.039) tiller control manual start 12-(80) choke valve start system forward-neutral-reverse 2.08 (27/13) ma...
Page 56: Transporting and
4-3 e trailering outboard motor the motor should be trailered and stored in the normal running position. If there is insufficient road clearance in this position, then trailer the motor in the tilt position using a motor support device such as a transom saver bar. C c do not use the tilt support lev...
Page 57
4-4 e 102015 q 102013 w emk22010** storing outboard motor when storing your yamaha outboard for prolonged periods of time, (2 months or longer), several important procedures must be performed to prevent expensive damage. It is advisable to have your outboard ser- viced by an authorized yamaha dealer...
Page 58
4-5 e emu00338* flushing cooling system and fogging engine cooling system flushing is essential to prevent the cooling system from clogging up with salt, sand, or dirt. In addition, fog- ging of the engine is mandatory to pre- vent expensive engine damage due to rust. Perform the flushing and foggin...
Page 59
4-6 e emk26010 lubrication 1) remove the spark plugs, and spray a 10 second spray of yamaha stor-rite engine fogging oil into each cylinder. Grease the spark plug threads and reinstall the spark plugs and torque to proper specification. (refer to the periodic maintenance section, “cleanning and adju...
Page 60: Periodic Maintenance
4-7 e emu01569 periodic maintenance w be sure to turn off the engine when you perform maintenance unless otherwise specified. If the owner is not familiar with machine servicing, this work should be done by a yamaha dealer or other quali- fied mechanic. Maintenance, replacement, or repair of the emi...
Page 61
4-8 e emu19450 maintenance chart frequency of maintenance operations may be adjusted according to the operating con- ditions, but the following table gives general guidelines. Refer to the sections in this chapter for explanations of each owner-specific action. The mark ( ●) indicates the check-ups ...
Page 62
4-9 e emu01202 cleaning and adjusting spark plug w when removing or installing a spark plug, be careful not to damage the insulator. A damaged insulator could allow external sparks, which could lead to explosion or fire. The spark plug is an important engine component and is easy to inspect. The con...
Page 63
4-10 e when fitting the plug, always clean the gasket surface and use a new gasket. Wipe off any dirt from the threads and screw in the spark plug to the correct torque. Note: if a torque-wrench is not available when you are fitting a spark plug, a good esti- mate of the correct torque is 1/4 to 1/2...
Page 64
4-11 e emk38010 checking fuel system w gasoline (petrol) and its vapors are highly flammable and explosive. Keep away from sparks, cigarettes, flames or other sources of ignition. Check the fuel line for leaks, cracks, or malfunctions. If any problem is found, it should be repaired immediately by ya...
Page 65
4-12 e emu00370 inspecting fuel filter w gasoline (petrol) is highly flammable, and its vapors are flammable and explosive. 8 if you have any question about properly doing this procedure, consult your yamaha dealer. 8 do not perform this procedure on a hot or running engine. Allow the engine to cool...
Page 66
Emu09912 inspecting idling speed w 8 do not touch or remove electrical parts when starting or during operation. 8 keep hands, hair and clothes away from flywheel and other rotating parts while engine is running. C c this procedure must be performed while the outboard motor is in the water. A flushin...
Page 67
4-14 e emk78010 checking wiring and connectors 1) check that each grounding wire is properly secured. 2) check that each connector is engaged securely. Exhaust leakage start the engine and check that no exhaust leaks from the joints between the exhaust cover, cylinder head and crank case. Water leak...
Page 68
E 4-15 emu00366 greasing yamaha marine grease (water resistant grease) 103011 63v-9-16-4 2/18/03 14:56 page 16.
Page 69
E 4-16 emu00388 checking propeller w you could be seriously injured if the engine accidentally starts while you are near the propeller. 8 before inspecting, removing or installing the propeller, remove the spark plug caps from the spark plugs. Also, put the shift control in neutral, put the main swi...
Page 70
Emu00396 installing the propeller c c 8 be sure to install the thrust washer before installing the propeller, other- wise the lower case and propeller boss may be damaged. 8 be sure to use a new cotter pin and bend the ends over securely. Otherwise the propeller could come off during operation and b...
Page 71
4-18 e emu01773 changing gear oil w 8 be sure the outboard motor is securely fastened to the transom or a stable stand. You could be severely injured if the outboard motor falls on you. 8 never get under the lower unit while it is tilted, even when the tilt support lever or knob is locked. Severe in...
Page 72
5) with the outboard motor in a vertical position, and using a flexible or pres- surized filling device, inject the gear oil into the gear oil drain screw hole. 6) when the oil begins to flow out of the oil level plug hole, insert and tighten the oil level plug. 7) insert and tighten the gear oil dr...
Page 73
4-20 e to clean the fuel tank: 1) empty the fuel tank into an approved gasoline container. 2) pour a small amount of suitable sol- vent in the tank. Reinstall the cap and shake the tank. Drain the solvent completely. To clean the fuel filter: 1) remove the screws holding the fuel meter assembly. Pul...
Page 74
4-21 e emu00409 motor exterior emu00410 cleaning the outboard motor after use, wash the exterior of the out- board with fresh water. Flush the cooling system with fresh water. Note: refer to flushing cooling system instruc- tions in “transporting and storing outboard motor”. Checking painted surface...
Page 75: Chapter 5
Emn00010 chapter 5 trouble recovery troubleshooting ..............................5-1 temporary action in emergency ............................................5-5 impact damege.....................................5-5 starter will not operate ........................5-6 treatment of submerged motor ...
Page 76: Troubleshooting
5-1 e emu01204¯ troubleshooting a problem in the fuel, compression, or ignition systems can cause poor starting, loss of power, or other problems. The troubleshooting chart describes basic checks and possi- ble remedies. (this chart covers all yamaha outboard motors. Therefore, some items may not ap...
Page 77
E 5-2 b. Engine idles irregularly or stalls. Trouble possible cause remedy 1. Spark plug(s) fouled or incorrect type. 2. Fuel system obstructed. 3. Fuel contaminated or stale. 4. Fuel filter clogged. 5. Failed ignition parts. 6. Spark plug gap incorrect. 7. Poor connections or damaged ignition wirin...
Page 78
5-3 e trouble possible cause remedy 1. Propeller damaged. 2. Propeller pitch or diameter incorrect. 3. Trim angle incorrect. 4. Motor mounted at incorrect height on transom. 5. Boat bottom fouled with marine growth. 6. Spark plug(s) fouled or incorrect type. 7. Weeds or other foreign matter tangled ...
Page 79
E 5-4 trouble possible cause remedy d. Engine vibrates excessively. 1. Propeller damaged. 2. Propeller shaft damaged. 3. Weeds or other foreign matter tangled on propeller. 4. Motor mounting bolt loose. 5. Steering pivot loose or damaged. 1. Have propeller repaired or replaced. 2. Have serviced by a...
Page 80: Temporary Action In
E 5-5 emn20010 temporary action in emergency 607011 emu01492 impact damage w the outboard motor can be seriously damaged by a collision while operating or trailering. Damage could make the out- board motor unsafe to operate. If the outboard motor hits any object in the water, follow the procedure be...
Page 81
E 5-6 emn30110 starter will not operate if the starter mechanism does not operate (engine cannot be cranked with the starter), the engine can be started with an emergency starter rope. W 8 use this procedure only in an emer- gency and only to return to port for repairs. 8 when the emergency starter ...
Page 82
E 5-7 208014 emr00001 4) to start the engine with emergency starter rope, insert the knotted end of the rope into the notch in the flywheel rotor and wind the rope several turns clockwise. Then, give a strong pull straight out to crank the engine. Repeat if necessary. 208012 407021** 301012 3) prepa...
Page 83
5-8 e emn50011 treatment of submerged motor if the outboard motor is submerged, immediately take it a yamaha dealer. Oth- erwise, some corrosion may begin almost immediately. If you cannot immediately take the outboard motor to a yamaha dealer, follow the procedure bellow for taking care to minimize...
Page 84: -Memo-
E -memo- 63v-9-16-5 2/18/03 14:14 page 10
Page 85: Chapter 6
Emp00010 chapter 6 index index ........................................................6-1 e 1 2 3 4 5 6 63v-9-16-6 2/18/03 14:19 page 1.
Page 86: Index
6-1 e emp10010 index a adjusting trim angle ..............................3-18 air vent screw...........................................2-2 b basic boating rules (rules of the road) ..1-6 breaking in (running in) engine..............3-8 c carrying handle........................................2-7 ch...
Page 87
6-2 e replacement parts ...................................4-7 reverse ...................................................3-15 s safety information ...................................1-3 shifting....................................................3-14 specifications ....................................
Page 88: Canada
Emu01599 important warranty information for u.S.A. And canada welcome to the yamaha family! Congratulations on the purchase of your new yamaha marine power. Yamaha is commit- ted to exceptional customer satisfaction, and we want your ownership experience to be a satisfying one. Please read the follo...
Page 89
5. Your warranty applies specifically to repairs made in the country of purchase. If your u.S.-purchased yamaha needs warranty service while in canada, or your canadian pur- chased yamaha needs service while in the united states, yamaha will assist the local dealer whenever possible. However, some p...
Page 90
Emu00912* yamaha motor corporation, u.S.A. Outboard motor two year limited warranty yamaha motor corporation, u.S.A. Is proud of its heritage and reputation for producing products with high standards of quality and workmanship. Product excellence provides the cornerstone for our commitment to custom...
Page 91
Specific parts excluded from warranty. Parts replaced due to normal wear or routine maintenance such as oil, spark plugs, shear pins, propellers, hubs, fuel and oil filters, brushes for the starter motor and power tilt motor, water pump impellers, and anodes are not covered by warranty. Charges for ...
Page 92
Customer service if your machine requires warranty service, you must take it to any authorized yamaha outboard dealer within the continental united states. Be sure to bring your warranty registration identification or other valid proof of the original date of purchase. If a question or problem arise...
Page 93
Emu01178 important warranty information if you use your yamaha outside u.S.A. Or canada welcome to the yamaha family! Congratulations on the purchase of your new yamaha marine power. Yamaha is com- mitted to exceptional customer satisfaction, and we want your ownership experience to be a satisfying ...
Page 94: 9.9C
Printed in japan march 2003-0.5 × 1 ! 63v-28199-16 (9.9fmh, 15fmh) (e) printed on recycled paper 9.9c 15c owner’s manual u.S.A.Edition lit-18626-05-34 63v-9-16 hyoshi 2/18/03 13:52 page 1.
Page 95
Yamaha motor co., ltd. Made in japan pays d'origine japon outboard motor warranty registration enregistrement de la garantie du moteur hors-bord please complete and mail this card. This information is necessary to accurately register your unit for warranty. Veuillez signer ci-dessous pour attester q...
Page 96: Attn: Warranty Department
Place postage here attn: warranty department warranty card 2/27/02 11:47 am page 2.