1. DL manuals
  2. Yamaha
  3. Motorcycle
  4. 2005 V Star XVS1100T
  5. Owner's Manual

Yamaha 2005 V Star XVS1100T Owner's Manual

Summary of 2005 V Star XVS1100T

  • Page 1

    Printed on recycled paper yamaha motor co., ltd. Printed in japan 2004.07-0.3 × 1 cr (e) 5pb-28199-23 xvs1100t owner’s manual.

  • Page 2

    U5pb23e0.Book page 2 friday, july 16, 2004 4:29 pm.

  • Page 3

    Introduction eau10100 welcome to the yamaha world of motorcycling! As the owner of the xvs1100, you are benefiting from yamaha’s vast experience and newest technology regarding the de- sign and manufacture of high-quality products, which have earned yamaha a reputation for dependability. Please take...

  • Page 4

    Important manual information eau10150 particularly important information is distinguished in this manual by the following notations: note: ● this manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle is subsequently sold. ● yamaha continuall...

  • Page 5

    Important manual information eau10200 xvs1100t owner’s manual ©2004 by yamaha motor co., ltd. 1st edition, july 2004 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor co., ltd. Is expressly prohibited. Printed in japan. U5pb23e0.Book page 2 friday...

  • Page 6

    Table of contents safety information ..................1-1 location of important labels ............1-5 description ..................................2-1 left view ..........................................2-1 right view ........................................2-2 controls and instruments..............

  • Page 7

    Table of contents replacing a turn signal light bulb or the tail/brake light bulb ..........6-27 supporting the motorcycle ............6-28 troubleshooting ............................6-29 troubleshooting chart ...................6-30 motorcycle care and storage ........................................

  • Page 8

    1-1 1 safety information eau10251 motorcycles are single track vehicles. Their safe use and operation are dependent upon the use of proper riding techniques as well as the ex- pertise of the operator. Ev- ery operator should know the following requirements before riding this motor- cycle. He or she ...

  • Page 9

    Safety information 1-2 1 wide on a turn due to excessive speed or undercornering (insuffi- cient lean angle for the speed). • always obey the speed limit and never travel faster than warrant- ed by road and traffic conditions. • always signal before turning or changing lanes. Make sure that other mo...

  • Page 10

    Safety information 1-3 1 loading the total weight of the operator, pas- senger, accessories and cargo must not exceed the maximum load limit. When loading within this weight limit, keep the following in mind: ● cargo and accessory weight should be kept as low and close to the motorcycle as possible....

  • Page 11

    Safety information 1-4 1 tor and may limit control ability, therefore, such accessories are not recommended. ● use caution when adding electri- cal accessories. If electrical acces- sories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause ...

  • Page 12

    Safety information 1-5 1 eau10381 location of important labels please read the following important labels carefully before operating this vehicle. 1 2 3 u5pb23e0.Book page 5 friday, july 16, 2004 4:29 pm.

  • Page 13

    Safety information 1-6 1 3 1 2 before you operate this vehicle, read the owner’s manual. Prima di usare il veicolo, leggete il manuale di istruzioni. Lire le manuel du propriétaire avant d’utiliser ce véhicule. Lesen sie die bedienungsanleitung bevor sie dieses fahrzeug fahren. Antes de conducir est...

  • Page 14

    Description 2-1 2 eau32220 left view 1. Shift pedal (page 3-5) 2. Fuel cock (page 3-7) 3. Headlight (page 6-26) 4. Shock absorber assembly spring preload adjusting ring (page 3-11) 5. Helmet holder (page 3-10) 6. Rear turn signal light (page 6-27) 7. Tail/brake light (page 6-27) 8. Storage compartme...

  • Page 15

    Description 2-2 2 eau32230 right view 1. Muffler 2. Battery (page 6-23) 3. Main fuse (page 6-25) 4. Fuel tank (page 3-6) 5. Front turn signal light (page 6-27) 6. Main switch/steering lock (page 3-1) 7. Air filter element (page 6-10) 8. Brake pedal (page 3-5) u5pb23e0.Book page 2 friday, july 16, 20...

  • Page 16

    Description 2-3 2 eau10430 controls and instruments 1. Clutch lever (page 3-4) 2. Left handlebar switches (page 3-3) 3. Starter (choke) lever (page 3-8) 4. Speedometer unit (page 3-3) 5. Fuel tank cap (page 3-6) 6. Right handlebar switches (page 3-3) 7. Throttle grip (page 6-12) 8. Brake lever (page...

  • Page 17

    Instrument and control functions 3-1 3 eau10460 main switch/steering lock the main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. Eau10480 on all electrical systems are supplied with power, and the headlig...

  • Page 18

    Instrument and control functions 3-2 3 eau11002 indicator and warning lights eau11020 turn signal indicator light “ ” this indicator light flashes when the turn signal switch is pushed to the left or right. Eau11060 neutral indicator light “ ” this indicator light comes on when the transmission is i...

  • Page 19

    Instrument and control functions 3-3 3 eau11731 speedometer unit the speedometer unit is equipped with a digital odometer and a tripmeter. The speedometer shows riding speed. The odometer shows the total distance trav- eled. The tripmeter shows the distance traveled since it was last set to zero. Pu...

  • Page 20

    Instrument and control functions 3-4 3 eau12350 pass switch “ ” press this switch to flash the headlight. Eau12400 dimmer switch “ / ” set this switch to “ ” for the high beam and to “ ” for the low beam. Eau12460 turn signal switch “ / ” to signal a right-hand turn, push this switch to “ ”. To sign...

  • Page 21

    Instrument and control functions 3-5 3 eau12870 shift pedal the shift pedal is located on the left side of the engine and is used in com- bination with the clutch lever when shifting the gears of the 5-speed con- stant-mesh transmission equipped on this motorcycle. Eau12890 brake lever the brake lev...

  • Page 22

    Instrument and control functions 3-6 3 eau13120 fuel tank cap to remove the fuel tank cap slide the lock cover open, insert the key into the lock, and then turn it 1/4 turn clockwise. The lock will be released and the fuel tank cap can be removed. To install the fuel tank cap 1. Insert the fuel tank...

  • Page 23

    Instrument and control functions 3-7 3 caution: eca10070 immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfac- es or plastic parts. Eau13330 caution: eca11400 use only unleaded gasoline. The use of leaded gasoline will cause severe damage to inte...

  • Page 24

    Instrument and control functions 3-8 3 on with the fuel cock lever in this position, fuel flows to the carburetors. Turn the fuel cock lever to this position when starting the engine and riding. Res this indicates reserve. With the fuel cock lever in this position, the fuel re- serve is made availab...

  • Page 25

    Instrument and control functions 3-9 3 eau14211 seats passenger seat to remove the passenger seat remove the nut, and then pull the pas- senger seat up. To install the passenger seat insert the projection on the front of the passenger seat into the seat holder as shown, place the seat in the origina...

  • Page 26

    Instrument and control functions 3-10 3 2. Install the seat bracket and bolts. 3. Install the passenger seat. Note: make sure that the seats are properly secured before riding. Eau14281 helmet holder to open the helmet holder, insert the key into the lock, and then turn the key as shown. To lock the...

  • Page 27

    Instrument and control functions 3-11 3 2. Pull the storage compartment cov- er out as shown. To close the storage compartment 1. Place the storage compartment cover in its original position as shown. 2. Turn the key counterclockwise, re- move it, and then close the lock cover. Eau14871 adjusting th...

  • Page 28

    Instrument and control functions 3-12 3 3. Pull the ignitor unit panel out to the right. 4. Remove the mudguard by remov- ing each quick fastener. 5. To increase the spring preload and thereby harden the suspension, turn the adjusting ring in direction (a). To decrease the spring pre- load and there...

  • Page 29

    Instrument and control functions 3-13 3 7. Install the rider seat. Warning ewa10220 this shock absorber contains highly pressurized nitrogen gas. For prop- er handling, read and understand the following information before handling the shock absorber. The manufacturer cannot be held re- sponsible for...

  • Page 30

    Instrument and control functions 3-14 3 below and have a yamaha dealer re- pair it if it does not function proper- ly. Eau15311 ignition circuit cut-off system the ignition circuit cut-off system (com- prising the sidestand switch, clutch switch and neutral switch) has the fol- lowing functions. ● i...

  • Page 31

    Instrument and control functions 3-15 3 with the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is turned on. 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? With the engine still runni...

  • Page 32

    Pre-operation checks 4-1 4 eau15591 the condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air p...

  • Page 33

    Pre-operation checks 4-2 4 eau15603 pre-operation check list item checks page fuel • check fuel level in fuel tank. • refuel if necessary. • check fuel line for leakage. 3-6 engine oil • check oil level in engine. • if necessary, add recommended oil to specified level. • check vehicle for oil leakag...

  • Page 34

    Pre-operation checks 4-3 4 throttle grip • make sure that operation is smooth. • check cable free play. • if necessary, have yamaha dealer adjust cable free play and lubricate cable and grip housing. 6-12, 6-19 control cables • make sure that operation is smooth. • lubricate if necessary. 6-19 wheel...

  • Page 35

    Operation and important riding points 5-1 5 eau15950 warning ewa10270 ● become thoroughly familiar with all operating controls and their functions before riding. Consult a yamaha dealer re- garding any control or function that you do not thoroughly un- derstand. ● never start the engine or oper- ate...

  • Page 36

    Operation and important riding points 5-2 5 diately stop the engine, and then check the engine oil level and the vehicle for oil leakage. If necessary, add engine oil, and then check the warning light again. If the warning light does not come on when turning the key to “on”, or if it does not go off...

  • Page 37

    Operation and important riding points 5-3 5 eau16671 shifting shifting gears lets you control the amount of engine power available for starting off, accelerating, climbing hills, etc. The gear positions are shown in the il- lustration. Note: to shift the transmission into the neu- tral position, pre...

  • Page 38

    Operation and important riding points 5-4 5 eau16841 engine break-in there is never a more important period in the life of your engine than the period between 0 and 1600 km (1000 mi). For this reason, you should read the follow- ing material carefully. Since the engine is brand new, do not put an ex...

  • Page 39

    Periodic maintenance and minor repair 6-1 6 eau17240 safety is an obligation of the owner. Pe- riodic inspection, adjustment and lubri- cation will keep your vehicle in the safest and most efficient condition pos- sible. The most important points of in- spection, adjustment, and lubrication are expl...

  • Page 40

    Periodic maintenance and minor repair 6-2 6 eau17705 periodic maintenance and lubrication chart note: ● the annual checks must be performed every year, except if a kilometer-based maintenance is performed in- stead. ● from 50000 km, repeat the maintenance intervals starting from 10000 km. ● items ma...

  • Page 41

    Periodic maintenance and minor repair 6-3 6 9 * brake hoses • check for cracks or damage. √ √ √ √ √ • replace. Every 4 years 10 * wheels • check runout, spoke tightness and for damage. • tighten spokes if necessary. √ √ √ √ 11 * tires • check tread depth and for damage. • replace if necessary. • che...

  • Page 42

    Periodic maintenance and minor repair 6-4 6 eau18670 note: ● the air filter needs more frequent service if you are riding in unusually wet or dusty areas. ● hydraulic brake service • regularly check and, if necessary, correct the brake fluid level. • every two years replace the internal components o...

  • Page 43

    Periodic maintenance and minor repair 6-5 6 eau18751 removing and installing the panel the panel shown needs to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time the panel needs to be removed and installed. Eau19151 panel a to remove the pa...

  • Page 44

    Periodic maintenance and minor repair 6-6 6 3. Remove the spark plug as shown, with the spark plug wrench includ- ed in the owner’s tool kit. To check the spark plugs 1. Check that the porcelain insulator around the center electrode on each spark plug is a medium-to- light tan (the ideal color when ...

  • Page 45

    Periodic maintenance and minor repair 6-7 6 note: if a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4–1/2 turn past finger tight. However, the spark plug should be tightened to the speci- fied torque as soon as possible. 4. Install the spark...

  • Page 46

    Periodic maintenance and minor repair 6-8 6 3. Remove the engine oil filler cap and drain bolt to drain the oil from the crankcase. 4. Install the engine oil drain bolt, and then tighten it to the specified torque. Note: check the washer for damage and re- place it if necessary. 5. Add the specified...

  • Page 47

    Periodic maintenance and minor repair 6-9 6 eau20022 final gear oil the final gear case must be checked for oil leakage before each ride. If any leakage is found, have a yamaha deal- er check and repair the vehicle. In addi- tion, the final gear oil level must be checked and the oil changed as follo...

  • Page 48

    Periodic maintenance and minor repair 6-10 6 6. Check the final gear case for oil leakage. If oil is leaking, check for the cause. Eau20670 cleaning the air filter element the air filter element should be cleaned as follows at the intervals specified in the periodic maintenance and lubrica- tion cha...

  • Page 49

    Periodic maintenance and minor repair 6-11 6 caution: eca10480 ● make sure that the air filter ele- ment is properly seated in the air filter case. ● the engine should never be op- erated without the air filter ele- ment installed, otherwise the piston(s) and/or cylinder(s) may become excessively wo...

  • Page 50

    Periodic maintenance and minor repair 6-12 6 note: if the specified idling speed cannot be obtained as described above, have a yamaha dealer make the adjustment. Eau21381 checking the throttle cable free play the throttle cable free play should mea- sure 4.0–6.0 mm (0.16–0.24 in) at the throttle gri...

  • Page 51

    Periodic maintenance and minor repair 6-13 6 eau32771 tires to maximize the performance, durabil- ity, and safe operation of your motor- cycle, note the following points regarding the specified tires. Tire air pressure the tire air pressure should be checked and, if necessary, adjusted before each r...

  • Page 52

    Periodic maintenance and minor repair 6-14 6 in it, or if the sidewall is cracked, con- tact a yamaha dealer immediately and have the tire replaced. Note: the tire tread depth limits may differ from country to country. Always comply with the local regulations. Warning ewa10560 ● it is dangerous to r...

  • Page 53

    Periodic maintenance and minor repair 6-15 6 eau21940 spoke wheels to maximize the performance, durabil- ity, and safe operation of your motor- cycle, note the following points regarding the specified wheels. ● the wheel rims should be checked for cracks, bends or warpage, and the spokes for loosene...

  • Page 54

    Periodic maintenance and minor repair 6-16 6 eau22092 adjusting the brake lever free play the brake lever free play should mea- sure 5.0–8.0 mm (0.20–0.31 in) as shown. Periodically check the brake le- ver free play and, if necessary, adjust it as follows. 1. Loosen the locknut at the brake le- ver....

  • Page 55

    Periodic maintenance and minor repair 6-17 6 eau22270 adjusting the rear brake light switch the rear brake light switch, which is ac- tivated by the brake pedal, is properly adjusted when the brake light comes on just before braking takes effect. If necessary, adjust the brake light switch as follow...

  • Page 56

    Periodic maintenance and minor repair 6-18 6 eau22580 checking the brake fluid level front brake rear brake insufficient brake fluid may allow air to enter the brake system, possibly caus- ing it to become ineffective. Before riding, check that the brake fluid is above the minimum level mark and rep...

  • Page 57

    Periodic maintenance and minor repair 6-19 6 eau22730 changing the brake fluid have a yamaha dealer change the brake fluid at the intervals specified in the note after the periodic mainte- nance and lubrication chart. In addition, have the oil seals of the master cylin- ders and calipers as well as ...

  • Page 58

    Periodic maintenance and minor repair 6-20 6 eau23131 checking and lubricating the brake and shift pedals the operation of the brake and shift pedals should be checked before each ride, and the pedal pivots should be lu- bricated if necessary. Eau23140 checking and lubricating the brake and clutch l...

  • Page 59

    Periodic maintenance and minor repair 6-21 6 eau23200 checking and lubricating the sidestand the operation of the sidestand should be checked before each ride, and the sidestand pivot and metal-to-metal contact surfaces should be lubricated if necessary. Warning ewa10730 if the sidestand does not mo...

  • Page 60

    Periodic maintenance and minor repair 6-22 6 eau23271 checking the front fork the condition and operation of the front fork must be checked as follows at the intervals specified in the periodic main- tenance and lubrication chart. To check the condition warning ewa10750 securely support the vehicle ...

  • Page 61

    Periodic maintenance and minor repair 6-23 6 eau23290 checking the wheel bearings the front and rear wheel bearings must be checked at the intervals specified in the periodic maintenance and lubrica- tion chart. If there is play in the wheel hub or if the wheel does not turn smoothly, have a yamaha ...

  • Page 62

    Periodic maintenance and minor repair 6-24 6 warning ewa10760 ● electrolyte is poisonous and dangerous since it contains sul- furic acid, which causes severe burns. Avoid any contact with skin, eyes or clothing and al- ways shield your eyes when working near batteries. In case of contact, administer...

  • Page 63

    Periodic maintenance and minor repair 6-25 6 eau27102 replacing the fuses the main fuse is located under the igni- tor unit panel. The fuse box, which contains the fuses for the individual circuits, is located in- side the storage compartment. (see page 3-10.) if a fuse is blown, replace it as follo...

  • Page 64

    Periodic maintenance and minor repair 6-26 6 caution: eca10640 do not use a fuse of a higher amper- age rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire. 6. Turn the key to “on” and turn on the electrical circuit in question to check if the devic...

  • Page 65

    Periodic maintenance and minor repair 6-27 6 warning ewa10790 headlight bulbs get very hot. There- fore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new headlight bulb into po- sition, and then secure it with the bulb holder....

  • Page 66

    Periodic maintenance and minor repair 6-28 6 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 4. Install the lens by installing the screws. Caution: eca10680 do not overtigh...

  • Page 67

    Periodic maintenance and minor repair 6-29 6 eau25850 troubleshooting although yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur dur- ing operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and ...

  • Page 68

    Periodic maintenance and minor repair 6-30 6 eau25891 troubleshooting chart warning ewa10840 keep away open flames and do not smoke while checking or working on the fuel system. Check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There is no fuel. Check the compression. Supply fuel....

  • Page 69

    Motorcycle care and storage 7-1 7 eau26060 care while the open design of a motorcycle reveals the attractiveness of the tech- nology, it also makes it more vulnera- ble. Rust and corrosion can develop even if high-quality components are used. A rusty exhaust pipe may go un- noticed on a car, however...

  • Page 70

    Motorcycle care and storage 7-2 7 after normal use remove dirt with warm water, a mild detergent, and a soft, clean sponge, and then rinse thoroughly with clean water. Use a toothbrush or bottlebrush for hard-to-reach areas. Stubborn dirt and insects will come off more easily if the area is covered ...

  • Page 71

    Motorcycle care and storage 7-3 7 ● avoid using abrasive polishing compounds as they will wear away the paint. Note: consult a yamaha dealer for advice on what products to use. Eau26230 storage short-term always store your motorcycle in a cool, dry place and, if necessary, protect it against dust wi...

  • Page 72

    Motorcycle care and storage 7-4 7 warning ewa10950 to prevent damage or injury from sparking, make sure to ground the spark plug electrodes while turning the engine over. 6. Lubricate all control cables and the pivoting points of all levers and pedals as well as of the side- stand/centerstand. 7. Ch...

  • Page 73

    Specifications 8-1 8 dimensions: overall length: 2405 mm (94.7 in) overall width: 895 mm (35.2 in) overall height: 1095 mm (43.1 in) seat height: 690 mm (27.2 in) wheelbase: 1640 mm (64.6 in) ground clearance: 145 mm (5.71 in) minimum turning radius: 3200 mm (126.0 in) weight: with oil and fuel: 275...

  • Page 74

    Specifications 8-2 8 gear ratio: 1st: 40/17 (2.353) 2nd: 40/24 (1.667) 3rd: 36/28 (1.286) 4th: 32/31 (1.032) 5th: 29/34 (0.853) chassis: frame type: double cradle caster angle: 33.00 ° trail: 136.0 mm (5.35 in) front tire: type: with tube size: 110/90-18m/c 61s manufacturer/model: dunlop/k555f manuf...

  • Page 75

    Specifications 8-3 8 voltage, capacity: 12 v, 12.0 ah headlight: bulb type: halogen bulb bulb voltage, wattage x quantity: headlight: 12 v, 60 w/55.0 w × 1 tail/brake light: 12 v, 5.0 w/21.0 w × 1 front turn signal light: 12 v, 21.0 w × 2 rear turn signal light: 12 v, 21.0 w × 2 meter lighting: 14 v...

  • Page 76

    Consumer information 9-1 9 eau26351 identification numbers record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the vehi- cle is stolen. ...

  • Page 77

    Consumer information 9-2 9 eau26470 model label the model label is affixed to the frame under the rider seat. (see page 3-9.) record the information on this label in the space provided. This information will be needed when ordering spare parts from a yamaha dealer. Eau26570 motorcycle noise regulati...

  • Page 78

    Index a air filter element, cleaning..................... 6-10 b battery................................................... 6-23 brake and clutch levers, checking and lubricating ..................... 6-20 brake and shift pedals, checking and lubricating ..................... 6-20 brake fluid, chang...

  • Page 79

    Index v valve clearance .................................... 6-12 vehicle identification number.................. 9-1 w wheel bearings, checking .................... 6-23 wheels.................................................. 6-15 u5pb23e0.Book page 2 friday, july 16, 2004 4:29 pm.

  • Page 80

    A5-yoko_blank.Fm page 1 tuesday, april 8, 2003 11:43 am.

  • Page 81

    A5-yoko_blank.Fm page 1 tuesday, april 8, 2003 11:43 am.

  • Page 82

    Printed on recycled paper yamaha motor co., ltd. Printed in japan 2004.07-0.3 × 1 cr (e) 5pb-28199-23 xvs1100t owner’s manual.