- DL manuals
- Yamaha
- Motorcycle
- 2008 YZ 450 F
- Assembly Instructions Manual
Yamaha 2008 YZ 450 F Assembly Instructions Manual
Summary of 2008 YZ 450 F
Page 1
Gb yamaha yz 450 f 2008 assembly instructions fast part-no.: 9040
Page 2
List of contents introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1. Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. Warnings . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
Introduction dear customer, we would like to thank you for choosing our product and we wish to provide you with some information about this entirely unique and exclusive product, the fast box. In over 50 years of operation, the sito group has achieved a series of goals and advances that have con- tr...
Page 4
1. Technical data leovince fast kit 9040 exhaust item x3 leovince 3659 (slip-on > motocross/supermoto – aluminum) 3660 (full > system - off-road racing – full titanium “motocross/supermoto”) fast electronic control unit (ecu) dimensions size and weight length 90.00 mm width 64.00 mm height 26.50 mm ...
Page 5
3. General guarantee conditions 3.1 guarantee sito gruppo industriale s.P.A. Guarantees its own products in accordance with current legislation. In particular it guarantees conformity defects by repair or replacement within a suitable period of time. Except where the customer’s request is for the go...
Page 6
4. Important informaiton information in this manual that is of critical importance is marked with the following symbols: a danger symbol means be careful! Your safety is at risk! Failure to observe the instructions that follow this symbol could cause serious injury, if not the death of the rider, pe...
Page 7
6. Wiring out the following are some guidelines for cable and wiring layout. 1) a loose wire or cable can be a safety risk. After attaching them, check all wires to make sure they are properly secure. 2) do not squeeze wires against the soldering iron or the end of the clamp when soldering clamps ar...
Page 8
8. Removing the fairing take off the side panels removing the nuts shown in figure 2 and figure 2a. Take special care when removing the bolt 3 from the radiator. Note: clean all the parts and put them on a tray, keeping them in the order in which they were removed. Remove the bolts shown in figure 2...
Page 9
9. Removing the fuel tank before removing the fuel tank make sure the tap is in the off position, then disconnect the fuel hose from the engine (position 1, figure 3) and remove the nut that keeps the tap fastened to the frame (position 2, figure 3). Next remove the nut that attaches the fuel tank t...
Page 10
10. Removing the original wiring disconnect the original yamaha connectors positioned under the side panels and under the fuel tank that have just been removed, as shown in figure 4 and figure 4a. Note: check the electric wires and the connection elements, checking for the presence of stains, rust, ...
Page 11
11. Installation of the fast ecu attach the fast ecu, placed inside the rubber support, to the frame, using the original attachment points, as shown in figure 5. Check that the connection between the fast wiring and the ecu is correct, and if the connection is loose, check the connectors. Insert the...
Page 12
Connect the fast wiring connectors to the corresponding original connectors on the motorcycle, matching the colors of the connectors and making sure that the connection is properly made and is in no way loose. The connector of the neutral gear sensor is not used. We recommend you to protect it with ...
Page 13
12. Installation of the fast mapping switch the fast kit also includes the fast mapping switch, which utilizes a three-position switch complete with wiring, which makes it is possible to select one of the three different maps stored in the control unit’s memory. There are three positions, the top po...
Page 14
13. Positioning of the fast mapping switch the fast mapping switch is attached to the handlebar of the motorcycle, at the discretion of the rider, so that it is com- fortable to use in both a sitting and standing position. Attachment of the switch is ensured by means of a clamp and screws. A picture...
Page 15
14. Connecting the fast mapping switch the fast mapping switch is connected to the ecu via a special piece of wiring (grey connector). See figure 8. Keep the wiring away from exces- sively hot parts and away from moving parts, as to avoid damage or wear from rubbing. Avoid exces- sively sharp bends....
Page 16: Assembly Instructions
Gb instruction manual 2007 sito gruppo industriale all rights reserved reproduction or unauthorized use without the written permission of sito gruppo industrial, s.P.A. Is strictly forbidden 28/11/’07 assembly instructions.