1. DL manuals
  2. Yamaha
  3. Motorcycle
  4. 2010 XV250Z
  5. Owner's Manual

Yamaha 2010 XV250Z Owner's Manual

Summary of 2010 XV250Z

  • Page 1

    Dic183 xv250z read this manual carefully before operating this vehicle. 1be-28199-20 owner’s manual.

  • Page 2

    Eau46090 read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold. U1be20e0.Book page 1 tuesday, may 12, 2009 5:52 pm.

  • Page 3

    Introduction eau10102 welcome to the yamaha world of motorcycling! As the owner of the xv250z, you are benefiting from yamaha’s vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned yamaha a reputation for dependability. Please take th...

  • Page 4

    Important manual information eau10132 particularly important information is distinguished in this manual by the following notations: this is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injur...

  • Page 5

    Important manual information eau10200 xv250z owner’s manual ©2009 by yamaha motor co., ltd. 1st edition, april 2009 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor co., ltd. Is expressly prohibited. Printed in japan. U1be20e0.Book page 2 tuesday...

  • Page 6

    Table of contents location of important labels .............................................1-1 safety information ..................2-1 description ..................................3-1 left view ..........................................3-1 right view ........................................3-2 co...

  • Page 7

    Table of contents checking the steering ...................7-28 checking the wheel bearings .......7-28 battery ..........................................7-28 replacing the fuses ......................7-30 replacing the headlight bulb ........7-31 replacing the tail/brake light bulb ...................

  • Page 8

    Location of important labels 1-1 1 eau10383 read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is av...

  • Page 9

    Location of important labels 1-2 1 3 cold tire normal pressure should be set as follows. 225 2.25 33 200 2.00 29 200 2.00 29 175 1.75 25 3ck-21668-a1 2 before you operate this vehicle, read the owner’s manual. Prima di usare il veicolo, leggete il manuale di istruzioni. Lire le manuel du propriétair...

  • Page 10

    2-1 2 safety information eau10283 be a responsible owner as the vehicle’s owner, you are respon- sible for the safe and proper operation of your motorcycle. Motorcycles are single-track vehicles. Their safe use and operation are de- pendent upon the use of proper riding techniques as well as the exp...

  • Page 11

    Safety information 2-2 2 due to excessive speed or under- cornering (insufficient lean angle for the speed). • always obey the speed limit and never travel faster than warrant- ed by road and traffic conditions. • always signal before turning or changing lanes. Make sure that other motorists can see...

  • Page 12

    Safety information 2-3 2 ● do not run engine in poorly venti- lated or partially enclosed areas such as barns, garages, or car- ports. ● do not run engine outdoors where engine exhaust can be drawn into a building through openings such as windows and doors. Loading adding accessories or cargo to you...

  • Page 13

    Safety information 2-4 2 aftermarket parts, accessories, and modifications while you may find aftermarket prod- ucts similar in design and quality to genuine yamaha accessories, recog- nize that some aftermarket accessories or modifications are not suitable be- cause of potential safety hazards to y...

  • Page 14

    Description 3-1 3 eau10410 left view 1. Headlight (page 7-31) 2. Steering lock (page 4-8) 3. Fuel tank (page 4-5) 4. Battery (page 7-28) 5. Fuses (page 7-30) 6. Helmet holder (page 4-9) 7. Shock absorber assembly spring preload adjusting ring (page 4-10) 8. Main switch (page 4-1) 9. Fuel cock (page ...

  • Page 15

    Description 3-2 3 eau10420 right view 1. Tail/brake light (page 7-32) 2. Rear turn signal light (page 7-33) 3. Rider seat (page 4-9) 4. Air filter element (page 7-11) 5. Front turn signal light (page 7-33) 6. Brake pedal (page 4-5) 7. Footrest 8. Rear brake light switch (page 7-20) 9. Owner’s tool k...

  • Page 16

    Description 3-3 3 eau10430 controls and instruments 1. Clutch lever (page 4-4) 2. Left handlebar switches (page 4-2) 3. Speedometer unit (page 4-2) 4. Indicator lights (page 4-1) 5. Right handlebar switches (page 4-2) 6. Brake lever (page 4-4) 7. Throttle grip (page 7-14) 8. Fuel tank cap (page 4-5)...

  • Page 17

    Instrument and control functions 4-1 4 eau10450 main switch the main switch controls the ignition and lighting systems. The various main switch positions are described below. Eau10480 on all electrical systems are supplied with power, and the headlight, meter lighting and taillight come on, and the ...

  • Page 18

    Instrument and control functions 4-2 4 eau11090 high beam indicator light “high beam” this indicator light comes on when the high beam of the headlight is switched on. Eau11630 speedometer unit the speedometer unit is equipped with a speedometer, an odometer and a tripmeter. The speedometer shows ri...

  • Page 19

    Instrument and control functions 4-3 4 right eau12360 pass switch “pass” press this switch to flash the headlight. Eau12410 dimmer switch “lights” set the switch to “hi” for the high beam and to “lo” for the low beam. Eau12440 turn signal switch “turn” to signal a right-hand turn, push this switch t...

  • Page 20

    Instrument and control functions 4-4 4 eau12820 clutch lever the clutch lever is located at the left handlebar grip. To disengage the clutch, pull the lever toward the handle- bar grip. To engage the clutch, release the lever. The lever should be pulled rapidly and released slowly for smooth clutch ...

  • Page 21

    Instrument and control functions 4-5 4 eau12941 brake pedal the brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the brake pedal. Eau13041 fuel tank cap to open the fuel tank cap insert the key into the lock and turn it 1/4 turn clockwise. The lock will be r...

  • Page 22

    Instrument and control functions 4-6 4 eau13212 fuel make sure there is sufficient gasoline in the tank. Warning ewa10881 gasoline and gasoline vapors are extremely flammable. To avoid fires and explosions and to reduce the risk of injury when refueling, follow these instructions. 1. Before refuelin...

  • Page 23

    Instrument and control functions 4-7 4 eau13581 fuel cock this model is equipped with a negative pressure fuel cock. The fuel cock sup- plies fuel from the tank to the carburetor while also filtering it. The fuel cock lever positions are ex- plained as follows and shown in the il- lustrations. On wi...

  • Page 24

    Instrument and control functions 4-8 4 eau13630 starter (choke) lever starting a cold engine requires a richer air-fuel mixture, which is supplied by the starter (choke). Move the lever in direction (a) to turn on the starter (choke). Move the lever in direction (b) to turn off the starter (choke). ...

  • Page 25

    Instrument and control functions 4-9 4 eau14220 rider seat to remove the rider seat remove the bolts, and then pull the rid- er seat off. To install the rider seat 1. Insert the projection on the front of the rider seat into the seat holder as shown. 2. Place the rider seat in the original position,...

  • Page 26

    Instrument and control functions 4-10 4 eau14882 adjusting the shock absorber assemblies warning ewa10210 always adjust both shock absorber assemblies equally, otherwise poor handling and loss of stability may result. Each shock absorber assembly is equipped with a spring preload adjust- ing ring. N...

  • Page 27

    Instrument and control functions 4-11 4 below and have a yamaha dealer re- pair it if it does not function proper- ly. Eau48240 ignition circuit cut-off system the ignition circuit cut-off system (com- prising the sidestand switch, clutch switch and neutral switch) has the fol- lowing functions. ● i...

  • Page 28

    Instrument and control functions 4-12 4 with the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is set to “run”. 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? With the engine still ru...

  • Page 29

    For your safety – pre-operation checks 5-1 5 eau15596 inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the owner’s manual. Warning ewa11151 failure to inspect or maint...

  • Page 30

    For your safety – pre-operation checks 5-2 5 clutch • check operation. • lubricate cable if necessary. • check lever free play. • adjust if necessary. 7-17 throttle grip • make sure that operation is smooth. • check cable free play. • if necessary, have yamaha dealer adjust cable free play and lubri...

  • Page 31

    For your safety – pre-operation checks 5-3 5 battery • check fluid level. • fill with distilled water if necessary. 7-28 item checks page u1be20e0.Book page 3 tuesday, may 12, 2009 5:52 pm.

  • Page 32

    Operation and important riding points 6-1 6 eau15951 read the owner’s manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your yamaha dealer. Warning ewa10271 failure to familiarize yourself with the controls can lead to loss of con- tr...

  • Page 33

    Operation and important riding points 6-2 6 eau16640 starting a warm engine follow the same procedure as for start- ing a cold engine with the exception that the starter (choke) is not required when the engine is warm. Eau16671 shifting shifting gears lets you control the amount of engine power avai...

  • Page 34

    Operation and important riding points 6-3 6 eau16800 tips for reducing fuel con- sumption fuel consumption depends largely on your riding style. Consider the following tips to reduce fuel consumption: ● turn the starter (choke) off as soon as possible. ● shift up swiftly, and avoid high en- gine spe...

  • Page 35

    Operation and important riding points 6-4 6 eau17201 parking when parking, stop the engine, and then remove the key from the main switch. Warning ewa10311 ● since the engine and exhaust system can become very hot, park in a place where pedestri- ans or children are not likely to touch them and be bu...

  • Page 36

    Periodic maintenance and adjustment 7-1 7 eau17241 periodic inspection, adjustment, and lu- brication will keep your vehicle in the safest and most efficient condition pos- sible. Safety is an obligation of the vehi- cle owner/operator. The most important points of vehicle inspection, adjust- ment, ...

  • Page 37

    Periodic maintenance and adjustment 7-2 7 eau46861 tip ● the annual checks must be performed every year, except if a kilometer-based maintenance, or for the uk, a mileage-based maintenance, is performed instead. ● from 50000 km (30000 mi), repeat the maintenance intervals starting from 10000 km (600...

  • Page 38

    Periodic maintenance and adjustment 7-3 7 eau1770c general maintenance and lubrication chart no. Item check or maintenance job odometer reading annual check 1000 km (600 mi) 10000 km (6000 mi) 20000 km (12000 mi) 30000 km (18000 mi) 40000 km (24000 mi) 1 air filter element • clean. √ √ • replace. √ ...

  • Page 39

    Periodic maintenance and adjustment 7-4 7 9 * wheel bearings • check bearing for looseness or damage. √ √ √ √ 10 * swingarm pivot bushes • check bush assemblies for loose- ness. √ √ √ √ • lubricate with lithium-soap-based grease. Every 10000 km (6000 mi) 11 drive chain • check chain slack, alignment...

  • Page 40

    Periodic maintenance and adjustment 7-5 7 eau18660 tip ● the air filter needs more frequent service if you are riding in unusually wet or dusty areas. 19 * sidestand switch • check operation. √ √ √ √ √ √ 20 * front fork • check operation and for oil leak- age. √ √ √ √ 21 * shock absorber as- semblie...

  • Page 41

    Periodic maintenance and adjustment 7-6 7 ● hydraulic brake service • regularly check and, if necessary, correct the brake fluid level. • every two years replace the internal components of the brake master cylinder and caliper, and change the brake fluid. • replace the brake hoses every four years a...

  • Page 42

    Periodic maintenance and adjustment 7-7 7 eau18751 removing and installing the panel the panel shown needs to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time the panel needs to be removed and installed. Eau19510 panel a to remove the pane...

  • Page 43

    Periodic maintenance and adjustment 7-8 7 to check the spark plugs 1. Check that the porcelain insulator around the center electrode on each spark plug is a medium-to- light tan (the ideal color when the vehicle is ridden normally). 2. Check that all spark plugs installed in the engine have the same...

  • Page 44

    Periodic maintenance and adjustment 7-9 7 eau42103 engine oil and oil filter ele- ment the engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter ele- ment replaced at the intervals specified in the periodic maintenance and lubri- cation chart. T...

  • Page 45

    Periodic maintenance and adjustment 7-10 7 5. Remove and replace the oil filter element and o-ring. 6. Install the oil filter element cover by installing the screws, then tighten- ing them to the specified torque. Tip make sure that the o-ring is properly seated. 7. Install the engine oil drain bolt...

  • Page 46

    Periodic maintenance and adjustment 7-11 7 9. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, im- mediately turn the engine off and check for the cause. 10. Turn the engine off, and then check the oil level and correct it if necessary....

  • Page 47

    Periodic maintenance and adjustment 7-12 7 3. Remove the air filter case cover by removing the screws. 4. Remove the air filter element by removing the wing nut. 5. Remove the sponge material from the air filter element frame, clean it with solvent, and then squeeze the remaining solvent out. Warnin...

  • Page 48

    Periodic maintenance and adjustment 7-13 7 engine should never be operat- ed without the air filter element installed, otherwise the pis- ton(s) and/or cylinder(s) may become excessively worn. [eca10481] 9. Install the air filter case cover by in- stalling the screws. 10. Connect the hoses to the ai...

  • Page 49

    Periodic maintenance and adjustment 7-14 7 tip if the specified idling speed cannot be obtained as described above, have a yamaha dealer make the adjustment. Eau21382 checking the throttle cable free play the throttle cable free play should mea- sure 3.0–5.0 mm (0.12–0.20 in) at the throttle grip. P...

  • Page 50

    Periodic maintenance and adjustment 7-15 7 eau32773 tires to maximize the performance, durabil- ity, and safe operation of your motorcy- cle, note the following points regarding the specified tires. Tire air pressure the tire air pressure should be checked and, if necessary, adjusted before each rid...

  • Page 51

    Periodic maintenance and adjustment 7-16 7 tip the tire tread depth limits may differ from country to country. Always comply with the local regulations. Warning ewa10561 ● it is dangerous to ride with a worn-out tire. When a tire tread begins to show crosswise lines, have a yamaha dealer replace the...

  • Page 52

    Periodic maintenance and adjustment 7-17 7 ● ride at moderate speeds after changing a tire since the tire sur- face must first be “broken in” for it to develop its optimal characteris- tics. Eau22043 adjusting the clutch lever free play the clutch lever free play should mea- sure 10.0–15.0 mm (0.39–...

  • Page 53

    Periodic maintenance and adjustment 7-18 7 6. To increase the clutch lever free play, turn the adjusting nut in direc- tion (a). To decrease the clutch le- ver free play, turn the adjusting nut in direction (b). 7. Tighten the locknut at the crank- case. 8. Tighten the locknut at the clutch le- ver ...

  • Page 54

    Periodic maintenance and adjustment 7-19 7 eau22201 adjusting the brake pedal po- sition and free play warning ewa10670 it is advisable to have a yamaha dealer make these adjustments. Brake pedal position the top of the brake pedal should be positioned approximately 60.0 mm (2.36 in) above the top o...

  • Page 55

    Periodic maintenance and adjustment 7-20 7 ● if proper adjustment cannot be obtained as described, have a yamaha dealer make this ad- justment. ● after adjusting the brake pedal free play, check the operation of the brake light. Eau22272 adjusting the rear brake light switch the rear brake light, wh...

  • Page 56

    Periodic maintenance and adjustment 7-21 7 indicator groove has almost disap- peared, have a yamaha dealer replace the brake pads as a set. Eau22540 rear brake shoes the rear brake is provided with a wear indicator, which allows you to check the brake shoe wear without having to dis- assemble the br...

  • Page 57

    Periodic maintenance and adjustment 7-22 7 eau22721 changing the brake fluid have a yamaha dealer change the brake fluid at the intervals specified in the tip after the periodic maintenance and lubrication chart. In addition, have the oil seals of the brake master cylin- der and caliper as well as t...

  • Page 58

    Periodic maintenance and adjustment 7-23 7 2. Remove the cotter pin from the axle nut, and then loosen the axle nut. 3. Loosen the chain puller locknut at each end of the swingarm. 4. To tighten the drive chain, turn the drive chain slack adjusting nut at each end of the swingarm in direc- tion (a)....

  • Page 59

    Periodic maintenance and adjustment 7-24 7 eau23024 cleaning and lubricating the drive chain the drive chain must be cleaned and lubricated at the intervals specified in the periodic maintenance and lubrica- tion chart, otherwise it will quickly wear out, especially when riding in dusty or wet areas...

  • Page 60

    Periodic maintenance and adjustment 7-25 7 eau23111 checking and lubricating the throttle grip and cable the operation of the throttle grip should be checked before each ride. In addi- tion, the cable should be lubricated at the intervals specified in the periodic maintenance chart. Eau44271 checkin...

  • Page 61

    Periodic maintenance and adjustment 7-26 7 eau23142 checking and lubricating the brake and clutch levers brake lever clutch lever the operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lu- bricated if necessary. Eau23202 checking and lubricati...

  • Page 62

    Periodic maintenance and adjustment 7-27 7 eaum1650 lubricating the swingarm piv- ots the swingarm pivots must be lubricat- ed at the intervals specified in the peri- odic maintenance and lubrication chart. Eau23272 checking the front fork the condition and operation of the front fork must be checke...

  • Page 63

    Periodic maintenance and adjustment 7-28 7 eau23283 checking the steering worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as fol- lows at the intervals specified in the pe- riodic maintenance and lubrication chart. 1. Place a stand under the...

  • Page 64

    Periodic maintenance and adjustment 7-29 7 3. If the electrolyte is at or below the minimum level mark, add distilled water to raise it to the maximum level mark. Notice: use only distilled water, as tap water con- tains minerals that are harmful to the battery. [eca10611] warning ewa10770 ● electro...

  • Page 65

    Periodic maintenance and adjustment 7-30 7 3. Fully charge the battery before in- stallation. 4. After installation, make sure that the battery leads are properly con- nected to the battery terminals and that the breather hose is properly routed, in good condition, and not obstructed. Notice: if the...

  • Page 66

    Periodic maintenance and adjustment 7-31 7 eau23783 replacing the headlight bulb this model is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. Notice eca10650 take care not to damage the follow- ing parts: ● headlight bulb do not touch the glass part of...

  • Page 67

    Periodic maintenance and adjustment 7-32 7 5. Install the headlight bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the screws. 7. Have a yamaha dealer adjust the headlight beam if necessary. Eau24133 replacing the tail/brake light bulb 1. Remove the tail/brak...

  • Page 68

    Periodic maintenance and adjustment 7-33 7 eau24212 replacing a turn signal light bulb 1. Remove the turn signal lens by re- moving the screws. 2. Remove the burnt-out bulb by pushing it in and turning it counter- clockwise. 3. Insert a new bulb into the socket, push it in, and then turn it clock- w...

  • Page 69

    Periodic maintenance and adjustment 7-34 7 a jack either under each side of the frame in front of the rear wheel or under each side of the swingarm. Eau24360 front wheel eau24601 to remove the front wheel warning ewa10821 to avoid injury, securely support the vehicle so there is no danger of it fall...

  • Page 70

    Periodic maintenance and adjustment 7-35 7 2. Lift the wheel up between the fork legs. Tip make sure that there is enough space between the brake pads before insert- ing the brake disc and that the slot in the speedometer gear unit fits over the retainer on the fork leg. 3. Insert the wheel axle. 4....

  • Page 71

    Periodic maintenance and adjustment 7-36 7 eau25080 rear wheel eau32751 to remove the rear wheel warning ewa10821 to avoid injury, securely support the vehicle so there is no danger of it falling over. 1. Remove the axle nut cotter pin. 2. Loosen the chain puller locknut and the drive chain slack ad...

  • Page 72

    Periodic maintenance and adjustment 7-37 7 6. Tighten the brake torque rod nut to the specified torque. 7. Adjust the drive chain slack. (see page 7-22.) 8. Tighten the axle nut to the speci- fied torque. 9. Insert a new cotter pin into the axle nut, and then bend its ends as shown. Warning! Always ...

  • Page 73

    Periodic maintenance and adjustment 7-38 7 heaters or furnaces. Gasoline or gasoline vapors can ignite or ex- plode, causing severe injury or property damage. U1be20e0.Book page 38 tuesday, may 12, 2009 5:52 pm.

  • Page 74

    Periodic maintenance and adjustment 7-39 7 eau25932 troubleshooting chart check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There is no fuel. Check the compression. Supply fuel. Operate the electric starter. 2. Compression there is compression. There is no compression. Check the i...

  • Page 75

    Motorcycle care and storage 8-1 8 eau37833 matte color caution notice eca15192 some models are equipped with matte colored finished parts. Be sure to consult a yamaha dealer for advice on what products to use be- fore cleaning the vehicle. Using a brush, harsh chemical products or cleaning compounds...

  • Page 76

    Motorcycle care and storage 8-2 8 off any detergent residue using plenty of water, as it is harmful to plastic parts. ● do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products, solvent or t...

  • Page 77

    Motorcycle care and storage 8-3 8 4. To prevent corrosion, it is recom- mended to apply a corrosion pro- tection spray on all metal, including chrome- and nickel-plat- ed, surfaces. 5. Use spray oil as a universal clean- er to remove any remaining dirt. 6. Touch up minor paint damage caused by stone...

  • Page 78

    Motorcycle care and storage 8-4 8 3. Drain the carburetor float cham- bers by loosening the drain bolts; this will prevent fuel deposits from building up. Pour the drained fuel into the fuel tank. 4. Fill up the fuel tank and add fuel stabilizer (if available) to prevent the fuel tank from rusting a...

  • Page 79

    Specifications 9-1 9 dimensions: overall length: 2190 mm (86.2 in) overall width: 815 mm (32.1 in) overall height: 1140 mm (44.9 in) seat height: 685 mm (27.0 in) wheelbase: 1490 mm (58.7 in) ground clearance: 145 mm (5.71 in) minimum turning radius: 2800 mm (110.2 in) weight: with oil and fuel: 147...

  • Page 80

    Specifications 9-2 9 3rd: 29/23 (1.261) 4th: 26/26 (1.000) 5th: 23/28 (0.821) chassis: frame type: double cradle caster angle: 32.00 ° trail: 120.0 mm (4.72 in) front tire: type: with tube size: 3.00-18 47p manufacturer/model: cheng shin/c-916 rear tire: type: with tube size: 130/90-15m/c 66p manufa...

  • Page 81

    Specifications 9-3 9 front turn signal light: 12 v, 21.0 w × 2 rear turn signal light: 12 v, 21.0 w × 2 meter lighting: 14 v, 3.0 w × 1 neutral indicator light: 14 v, 3.0 w × 1 high beam indicator light: 12 v, 1.7 w × 1 turn signal indicator light: 14 v, 3.0 w × 1 fuses: main fuse: 20.0 a signaling ...

  • Page 82

    Consumer information 10-1 10 eau26352 identification numbers record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the vehi- cle is stolen...

  • Page 83

    Consumer information 10-2 10 eau26470 model label the model label is affixed to the frame under the rider seat. (see page 4-9.) record the information on this label in the space provided. This information will be needed when ordering spare parts from a yamaha dealer. Eau26570 motorcycle noise regula...

  • Page 84

    Index a air filter element, cleaning..................... 7-11 b battery................................................... 7-28 brake and clutch levers, checking and lubricating ..................... 7-26 brake and shift pedals, checking and lubricating ..................... 7-25 brake fluid, chang...

  • Page 85

    Index v valve clearance .................................... 7-14 vehicle identification number................ 10-1 w wheel bearings, checking .................... 7-28 wheel (front) ......................................... 7-34 wheel (rear).......................................... 7-36 wheels......

  • Page 86

    A5-yoko_blank.Fm page 1 tuesday, april 8, 2003 11:43 am.

  • Page 87

    A5-yoko_blank.Fm page 1 tuesday, april 8, 2003 11:43 am.

  • Page 88

    Printed on recycled paper yamaha motor co., ltd. Printed in japan 2009.05-0.3 × 1 cr (e) dic183.