- DL manuals
- Yamaha
- Boat
- 2011 WaveRunner FZR
- Owner's/operator's Manual
Yamaha 2011 WaveRunner FZR Owner's/operator's Manual
Summary of 2011 WaveRunner FZR
Page 1
2011 waverunner fzr owner’s/operator’s manual f2r-f8199-12 lit-18626-09-09 u.S.A. Edition read this manual carefully before operating this watercraft. Dic183.
Page 2
Read this manual carefully before operating this watercraft. This manual should stay with the waverunner if it is sold. Uf2r12e0.Book page 1 tuesday, july 6, 2010 9:21 am.
Page 3
Important manual information eju30182 to the owner/operator thank you for choosing a yamaha watercraft. This owner’s/operator’s manual contains in- formation you will need for proper operation, maintenance, and care. A thorough under- standing of these simple instructions will help you to obtain max...
Page 4: Table Of Contents
Table of contents general and important labels........... 1 identification numbers .................... 1 primary identification (pri-id) number ........................................... 1 hull identification number (hin) ........ 1 engine serial number ........................ 1 emission control ...
Page 5: Table Of Contents
Table of contents transporting on a trailer ............... 56 first-time operation......................... 57 engine break-in ............................ 57 pre-operation checks...................... 58 pre-operation checklist .................... 58 pre-operation check points .......... 60 pre-l...
Page 6
General and important labels 1 eju30262 identification numbers record the primary identification (pri-id) number, hull identification number (hin), and engine serial number in the spaces provided for assistance when ordering genuine parts from a yamaha dealer. Also record and keep these id numbers i...
Page 7
General and important labels 2 eju30352 emission control information this engine conforms to u.S. Environmental protection agency (epa) and/or california air resources board (carb) regulations for ma- rine si engines applicable at the time of man- ufacture. This engine is certified to operate on reg...
Page 8
General and important labels 3 stallation procedures and page 87 for engine cover removal and installation procedures.) eju30440 star labels this watercraft is labeled with a california air resources board (carb) star label. See be- low for a description of your particular label. One star - low emis...
Page 9
General and important labels 4 these standards have 65% lower emissions than one star-low emission engines. Four stars - super ultra low emission the four-star label identifies engines that meet the air resources board’s sterndrive and inboard marine engine 2009 exhaust emission standards. Personal ...
Page 10
General and important labels 5 eju30452 important labels read the following labels before using this watercraft. If have any questions, consult a yamaha dealer. 1 2 3 4 5 10 12 8 9 7 6 11 uf2r12e0.Book page 5 tuesday, july 6, 2010 9:21 am.
Page 11
General and important labels 6 eju35913 warning labels if any of these labels are damaged or missing, contact a yamaha dealer for replacements. 1 2 uf2r12e0.Book page 6 tuesday, july 6, 2010 9:21 am.
Page 12
General and important labels 7 uf2r12e0.Book page 7 tuesday, july 6, 2010 9:21 am.
Page 13
General and important labels 8 eju35925 other labels uf2r12e0.Book page 8 tuesday, july 6, 2010 9:21 am.
Page 14
General and important labels 9 the following label indicates the correct direction to upright a capsized watercraft. Uf2r12e0.Book page 9 tuesday, july 6, 2010 9:21 am.
Page 15: Safety Information
Safety information 10 eju30671 the safe use and operation of this water- craft is dependent upon the use of proper riding techniques, as well as upon the common sense, good judgment, and ex- pertise of the operator. Every operator should know the following requirements before riding the watercraft. ...
Page 16: Safety Information
Safety information 11 eju30761 cruising limitations ● scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others. ● operate defensively at safe speeds and keep a safe distance away from people, ob- jects, and other wat...
Page 17: Safety Information
Safety information 12 with another boat, which could result in se- vere injury or death. ● follow navigation rules, and state/provin- cial and local laws that apply to watercraft. Eju30792 operation requirements ● all riders must wear a u.S. Coast guard (uscg) approved personal flotation device (pfd...
Page 18: Safety Information
Safety information 13 know that a helmet could help protect you in certain kinds of accidents and that it could injure you in others. A helmet is designed to provide some head protection. Although helmets cannot protect against all foreseeable impacts, a helmet might reduce your injuries in a collis...
Page 19: Safety Information
Safety information 14 tercraft to avoid accidental starting or unau- thorized use by children or others. ● scan carefully for swimmers and stay away from swimming areas. Swimmers are hard to see and you could accidentally hit some- one in the water. ● avoid being hit by another boat. You should alwa...
Page 20: Safety Information
Safety information 15 eju30830 recommended equipment the following items should be carried on board your watercraft: ● sound-signaling device you should carry a whistle or other sound- signaling device that can be used to signal other boats. See “rules of the road” for more information. ● visual dis...
Page 21: Safety Information
Safety information 16 eju30920 watercraft characteristics ● jet thrust turns the watercraft. Releasing the throttle lever completely produces only minimum thrust. If you are traveling at speeds above trolling, you will have rapidly decreasing ability to steer without throttle. This model is equipped...
Page 22: Safety Information
Safety information 17 any debris or weeds, which may have col- lected around the jet intake. Eju30961 rules of the road your yamaha watercraft is legally consid- ered a powerboat. Operation of the water- craft must be in accordance with the rules and regulations governing the waterway on which it is...
Page 23: Safety Information
Safety information 18 give-way vessel the vessel which does not have the right-of- way has the duty to take positive and timely action to stay out of the way of the stand-on vessel. Normally, you should not cross in front of the vessel with the right-of-way. You should slow down or change directions...
Page 24: Safety Information
Safety information 19 provided the other vessel gives you the right- of-way as it should. Overtaking if you are passing another vessel, you are the give-way vessel. This means that the other vessel is expected to maintain its course and speed. You must stay out of its way until you are clear of it. ...
Page 25: Safety Information
Safety information 20 many bodies of water used by boaters are en- tirely within the boundaries of a particular state. The uniform state waterway marking system has been devised for these waters. This system uses buoys and signs with dis- tinctive shapes and colors to show regulatory or advisory inf...
Page 26: Safety Information
Safety information 21 remember, markings may vary by geograph- ic location. Always consult local boating au- thorities before riding your watercraft in unfamiliar waters. Eju30982 to get more boating safety information be informed about boating safety. Additional publications and information can be ...
Page 27: Safety Information
Safety information 22 eju30991 enjoy your watercraft responsibly you share the areas you enjoy when riding your watercraft with others and with nature. So your enjoyment includes a responsibility to treat these other people, and the lands, wa- ters, and wildlife with respect and courtesy. Whenever a...
Page 28: Safety Information
Safety information 23 waterways stay open for the enjoyment of a variety of recreational opportunities. Uf2r12e0.Book page 23 tuesday, july 6, 2010 9:21 am.
Page 29: Description
Description 24 eju40302 watercraft glossary trolling speed “trolling” is the lowest maneuvering speed. You are applying little or no throttle. The watercraft is down in the water, and there is no wake. Sub-planing speed “sub-planing” is a medium speed. The bow of the watercraft is slightly up from t...
Page 30: Description
Description 25 eju31011 location of main components exterior 3 4 5 6 10 9 7 8 1 2 1 fuel filler cap (page 51) 2 hood 3 handlebars 4 rear seat (page 44) 5 front seat (page 44) 6 footwell 7 bow eye 8 cooling water pilot outlet (page 34) 9 gunwale 10 sponson uf2r12e0.Book page 25 tuesday, july 6, 2010 ...
Page 31: Description
Description 26 2 3 9 8 5 1 7 6 11 10 4 1 boarding platform 2 electric bilge pilot outlet 3 reboarding grip (page 45) 4 reboarding step (page 45) 5 jet thrust nozzle 6 reverse gate (page 35) 7 ride plate 8 stern drain plug (page 54) 9 stern eye (page 46) 10 speed sensor 11 intake grate uf2r12e0.Book ...
Page 32: Description
Description 27 1 2 3 4 6 7 5 10 11 12 13 14 9 8 1 q.S.T.S. Selector (page 36) 2 q.S.T.S. Selector lock lever (page 36) 3 start switch (page 31) 4 engine shut-off switch (page 31) 5 clip (page 31) 6 engine stop switch (page 31) 7 engine shut-off cord (lanyard) (page 31) 8 dual analog meter unit (page...
Page 33: Description
Description 28 engine compartment 1 2 3 4 6 5 9 10 8 7 1 engine cover 2 air filter case 3 water separator (page 34) 4 fuel tank 5 battery (page 61) 6 flushing hose connector 7 electrical box 8 spark plug/spark plug cap/ignition coil 9 engine oil filler cap (page 53) 10 dipstick uf2r12e0.Book page 28...
Page 34: Control Function Operation
Control function operation 29 eju31024 watercraft control functions eju41370 remote control transmitter the yamaha security system and low rpm mode settings can be selected by operating the remote control transmitter. (see page 30 for yamaha security system setting proce- dures and page 37 for low r...
Page 35: Control Function Operation
Control function operation 30 two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including in- terference that may cause undesired opera- tion. Notice ecj00030 changes or modifications not expressly approved by the party res...
Page 36: Control Function Operation
Control function operation 31 comes on. This indicates the unlock mode is selected. Eju31152 engine stop switch “ ” the engine stop switch (red button) stops the engine when the switch is pushed. Eju31163 engine shut-off switch “ ” the engine shut-off switch automatically stops the engine when the c...
Page 37: Control Function Operation
Control function operation 32 in 5 seconds, release the start switch, wait 15 seconds, and then try again. Notice: never push the start switch while the engine is running. Do not operate the start switch for more than 5 seconds, otherwise the battery will be discharged and the engine will not start....
Page 38: Control Function Operation
Control function operation 33 since the strength of the jet thrust determines the speed and degree of a turn, throttle must always be applied when attempting a turn, ex- cept at trolling speed. This model is equipped with the yamaha en- gine management system (yems) that in- cludes an off-throttle s...
Page 39: Control Function Operation
Control function operation 34 eju41800 cooling water pilot outlets when the engine is running, some of the cool- ing water that is circulated in the engine is dis- charged from the cooling water pilot outlets. There are cooling water pilot outlets on the port (left) and starboard (right) sides of th...
Page 40: Watercraft Operation
Watercraft operation 35 eju40011 watercraft operation functions eju37182 reverse system warning ewj01230 ● do not use the reverse function to slow down or stop the watercraft as it could cause you to lose control, be ejected, or impact the handlebars. ● make sure that there are no obstacles or peopl...
Page 41: Watercraft Operation
Watercraft operation 36 eju31317 quick shift trim system (q.S.T.S.) the q.S.T.S. Selector is integrated with the left handlebar grip and is operated to change the vertical angle of the jet thrust nozzle, which adjusts the trim angle of the watercraft. There are 5 positions: neutral, 2 bow-down posit...
Page 42: Watercraft Operation
Watercraft operation 37 3000 r/min or more, otherwise damage could occur to the q.S.T.S. [ecj00013] (3) release the lock lever, and then make sure that the q.S.T.S. Selector is securely locked in place. Eju40000 watercraft operation modes eju37423 low rpm mode the low rpm mode is a function that lim...
Page 43: Watercraft Operation
Watercraft operation 38 tip: if the remote control transmitter is operated while the dual analog meter unit is in the standby state, the unit will perform the initial operation, and then the setting is selected. To activate the low rpm mode: push the “l-mode” (unlock) button on the re- mote control ...
Page 44: Instrument Operation
Instrument operation 39 eju37432 dual analog meter unit the dual analog meter unit displays various watercraft information. Dual analog meter unit initial operation when the dual analog meter unit is activated, the speedometer and tachometer make one sweep, all of the display segments and indica- to...
Page 45: Instrument Operation
Instrument operation 40 eju35024 information display the information display shows watercraft op- erating conditions. Eju37264 hour meter/voltmeter the hour meter/voltmeter has both an hour meter function and a voltmeter function. By switching the meter, it can be used as either an hour meter or a v...
Page 46: Instrument Operation
Instrument operation 41 to switch to the voltmeter from the hour meter: push the “hour volt” button for at least 1 sec- ond. The display switches to the voltmeter from the hour meter. Eju37271 fuel level meter the fuel level meter shows the amount of fuel remaining in the fuel tank. The amount of re...
Page 47: Instrument Operation
Instrument operation 42 sounds intermittently. At the same time, the maximum engine speed is limited. If the oil pressure warning is activated, imme- diately reduce the engine speed, return to shore, and then check the engine oil level. (see page 53 for information on checking the engine oil level.)...
Page 48: Instrument Operation
Instrument operation 43 if the check engine warning is activated, im- mediately reduce the engine speed, return to shore, and have a yamaha dealer check the engine. Tip: push the “hour volt” button to stop the buzz- er. Uf2r12e0.Book page 43 tuesday, july 6, 2010 9:21 am.
Page 49: Equipment Operation
Equipment operation 44 eju40333 equipment eju41410 seats the front and rear seats are removable. Remove the seats to access the engine com- partment and watertight storage compart- ment. To remove the rear seat: (1) pull the rear seat latch up, and then lift up the rear of the seat. (2) pull the sea...
Page 50: Equipment Operation
Equipment operation 45 (3) pull the seat rearward and remove it. To install the front seat: (1) insert the projections on the front of the seat into the stays on the deck. (2) push the rear of the seat down to secure- ly lock it in place. (3) securely install the rear seat in its original position. ...
Page 51: Equipment Operation
Equipment operation 46 ing step breaks, the watercraft could fall, which could result in severe injury. [ewj01211] notice ecj00742 use the reboarding step only to board the watercraft in the water. Do not use the re- boarding step for any other purpose. The watercraft can be damaged. Eju34872 bow ey...
Page 52: Equipment Operation
Equipment operation 47 to open the bow storage compartment: push the hood latch, and then lift up the rear of the hood. To close the bow storage compartment: push the rear of the hood down to securely lock it in place. To drain water from the bow storage compart- ment: (1) remove the drain plug on t...
Page 53: Equipment Operation
Equipment operation 48 to open the glove compartment: slide the glove compartment latch toward you, and then lift up the lid. To close the glove compartment: push the lid down to securely lock it in place. To drain water from the glove compartment: (1) remove the beverage holder. (2) remove the drai...
Page 54: Equipment Operation
Equipment operation 49 (4) securely install the beverage holder in its original position. Eju41420 beverage holder the beverage holder is located in the glove compartment. (see page 47 for information on the glove compartment.) the beverage holder is removable. Do not place any items in the beverage...
Page 55: Equipment Operation
Equipment operation 50 to use the fire extinguisher holder and cover: (1) push the hood latch, and then lift up the rear of the hood. (2) unhook the band and remove the fire ex- tinguisher cover. (3) place the fire extinguisher in the holder, and then place the cover over the fire ex- tinguisher. (4...
Page 56
Operation and handling requirements 51 eju31822 fuel requirements eju41291 fuel warning ewj00282 ● gasoline and gasoline vapors are ex- tremely flammable. To avoid fires and explosions and to reduce the risk of in- jury when refueling, follow these in- structions. ● gasoline is poisonous and can cau...
Page 57
Operation and handling requirements 52 (5) loosen the fuel filler cap and remove it. (6) slowly add fuel to the fuel tank. (7) stop filling when the fuel level reaches approximately 50 mm (2 in) from the top of the fuel tank. Do not overfill the fuel tank. Because fuel expands when it heats up, heat...
Page 58
Operation and handling requirements 53 eju40290 engine oil requirements eju31894 engine oil notice ecj00281 use only 4-stroke engine oil. Usage of 2- stroke engine oil could result in severe en- gine damage. Checking the engine oil level warning ewj00340 engine oil is extremely hot immediately af- t...
Page 59
Operation and handling requirements 54 (6) loosen the engine oil filler cap and re- move it. (7) slowly add engine oil. Tip: the difference between the minimum and maximum level marks on the dipstick is equal to approximately 1 l (1.06 us qt, 0.88 imp. Qt) of engine oil. (8) wait approximately 5 min...
Page 60
Operation and handling requirements 55 maining moisture in the engine compart- ment with a dry cloth. (4) securely install the stern drain plugs by tightening them until they stop. Notice: before installing the stern drain plugs, clean the drain plug threads to remove any foreign materials, such as ...
Page 61
Operation and handling requirements 56 eju33464 transporting on a trailer when transporting the watercraft on a trailer, secure the tie downs to the trailer through the bow eye and stern eyes. Notice: do not at- tach ropes or tie downs to any part of the watercraft other than the bow eye and stern e...
Page 62: First-Time Operation
First-time operation 57 eju36665 engine break-in notice ecj00431 failure to perform the engine break-in could result in reduced engine life or even severe engine damage. The engine break-in is essential to allow the various components of the engine to wear and polish themselves to the correct operat...
Page 63: Pre-Operation Checks
Pre-operation checks 58 eju31981 warning ewj00411 failure to inspect or maintain the watercraft properly increases the possibility of an ac- cident or damage to the watercraft. Do not operate the watercraft if you find any prob- lem. If a problem cannot be corrected by the procedures provided in thi...
Page 64: Pre-Operation Checks
Pre-operation checks 59 tip: to ensure safety and reliability, pre-operation checks should be made each time the watercraft is used. Hull and deck check the hull and deck for damage. 66 jet intake check the jet intake for damage and clogging. 66 stern drain plugs check the stern drain plugs for dama...
Page 65: Pre-Operation Checks
Pre-operation checks 60 eju32281 pre-operation check points eju41311 pre-launch checks perform the pre-launch checks in the pre-op- eration checklist while the watercraft is on land. To perform the pre-launch checks: (1) remove the seats and watertight storage compartment. (see page 44 for seat re- ...
Page 66: Pre-Operation Checks
Pre-operation checks 61 eju40181 engine unit check check the exterior of the engine unit for dam- age or other problem. Eju36885 engine oil level check make sure that the engine oil level is between the minimum and maximum level marks on the dipstick. (see page 53 for information on checking the eng...
Page 67: Pre-Operation Checks
Pre-operation checks 62 make sure that the battery is securely held in place. Eju32613 steering system checks turn the handlebars to the right and left sev- eral times to make sure that operation is smooth and unrestricted throughout the whole range, and that the free play is not ex- cessive. Turn t...
Page 68: Pre-Operation Checks
Pre-operation checks 63 locked in place. (see page 33 for telescopic steering system operation procedures.) eju32644 quick shift trim system (q.S.T.S.) checks operate the q.S.T.S. Selector lock lever and the q.S.T.S. Selector several times to make sure that operation is smooth throughout the whole r...
Page 69: Pre-Operation Checks
Pre-operation checks 64 gate moves up and down according to the op- eration of the shift lever and that the gate makes contact with the stoppers. (see page 35 for reverse system operation.) eju41431 throttle lever checks operate the throttle lever several times to make sure that operation is smooth ...
Page 70: Pre-Operation Checks
Pre-operation checks 65 eju32663 engine shut-off cord (lanyard) check make sure that the engine shut-off cord (lan- yard) is not damaged. If the cord is damaged, replace it. Warning! Never try to repair the engine shut-off cord (lanyard) or tie it together. The engine shut-off cord (lan- yard) may n...
Page 71: Pre-Operation Checks
Pre-operation checks 66 eju41081 fire extinguisher holder, cover, and band checks make sure that the fire extinguisher holder, cover, and band are not damaged and that the cover is securely held in place using the band. (see page 49 for information on the fire extinguisher holder, cover, and band.) ...
Page 72: Pre-Operation Checks
Pre-operation checks 67 securely install the stern drain plugs by tight- ening them until they stop. Eju41440 hood check push down on the rear of the hood and make sure that it is securely closed. Eju40144 post-launch checks perform the post-launch checks in the pre-op- eration checklist while the w...
Page 73: Pre-Operation Checks
Pre-operation checks 68 significantly above or below the specified range. Engine idling speed: 1250 ± 100 r/min uf2r12e0.Book page 68 tuesday, july 6, 2010 9:21 am.
Page 74: Operation
Operation 69 eju32902 operating your watercraft warning ewj00510 before operating your watercraft, become familiar with all of the controls. Consult a yamaha dealer about any control or func- tion that you do not fully understand. Fail- ure to understand how the controls work could cause an accident...
Page 75: Operation
Operation 70 eju41340 riding position operator riding position the operator should grip the handlebars firm- ly with both hands and sit astride the seat with both feet on the floor of the footwell. Passenger riding position the passenger should hold on firmly to the operator and sit astride the seat...
Page 76: Operation
Operation 71 is attached correctly. If the engine shut-off cord (lanyard) is not attached correctly, it may not pull free when the operator falls off, allowing the water- craft to continue to run and cause an accident. [ewj00581] (4) with the throttle lever released, push the start switch (green but...
Page 77: Operation
Operation 72 is in the fully closed (idle) position. (see page 35 for information on operating the shift lever.) eju33254 turning the watercraft warning ewj00771 ● do not release the throttle lever when trying to steer away from objects—you need throttle to steer. A collision could result in severe ...
Page 78: Operation
Operation 73 slows down, the watercraft will no longer respond to handlebar input until you ap- ply throttle again or you reach trolling speed. At trolling speed, the watercraft can be turned gradually by handlebar position alone using just the amount of thrust available at idle. D. If the engine is...
Page 79: Operation
Operation 74 objects, and other watercraft to give you time to stop. ● do not shut the engine off when slowing down in case you need engine power to steer away from a boat or other obstacle that comes into your path. ● do not use the reverse function to slow down or stop the watercraft as it could c...
Page 80: Operation
Operation 75 eju37463 boarding alone (1) from the rear of the watercraft, place both hands on the boarding platform, pull yourself up, and then grasp the reboard- ing grip with one hand. (2) pull yourself up to a kneeling position on the boarding platform, and then move to the seat and sit astride. ...
Page 81: Operation
Operation 76 to board at a standstill: (1) board as noted in the previous section “boarding alone”. (2) attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch. (3) grip the handlebars with both hands and place both feet on the floor of th...
Page 82: Operation
Operation 77 to board when it is difficult to balance at a standstill: (1) have the passenger steady the water- craft, and then board as noted in the pre- vious section “boarding alone”. (2) grip the handlebars with both hands, place both feet on the floor of the footwell, and balance there. (3) att...
Page 83: Operation
Operation 78 throttle lever when trying to steer away from objects—you need throttle to steer. Notice ecj01340 never run the engine in water that is less than 60 cm (2 ft) deep from the bottom of the watercraft, otherwise pebbles or sand could be sucked into the jet intake, caus- ing impeller damage...
Page 84: Operation
Operation 79 craft over counterclockwise, otherwise water can enter the engine, which can result in severe damage. [ecj00541] (3) start the engine and operate the water- craft at planing speed to drain the bilge water from the engine compartment. (see page 54 for information on draining the bilge wa...
Page 85: Operation
Operation 80 weeded areas is unavoidable, alternately squeeze the throttle lever and relax your grip on the throttle lever to vary the engine speed. Weeds tend to become clogged more when operating at a steady speed and at trolling speed. If weeds may have clogged the intake area, clean the jet inta...
Page 86: Care And Storage
Care and storage 81 eju37145 post-operation care warning ewj00330 always place the watercraft upright in a horizontal position when storing it, other- wise fuel could leak out into the engine or engine compartment, which could create a fire hazard. After using the watercraft, always take it out of t...
Page 87: Care And Storage
Care and storage 82 flows out continually from the jet thrust nozzle. (7) run the engine at idling speed for about 3 minutes watching the engine condition. If the engine stops while flushing, turn the water supply off immediately and perform the procedure again from step 6. Notice: do not supply wat...
Page 88: Care And Storage
Care and storage 83 egg, or vegetable oil. Call a physician im- mediately. Eyes: flush with water for 15 minutes and get prompt medical attention. Batteries produce explosive gases. Keep sparks, flames, cigarettes, etc., well away. If using or charging the battery in an en- closed space, make sure t...
Page 89: Care And Storage
Care and storage 84 checking the battery bands make sure that the battery bands are not damaged. To store the battery: (1) clean the battery case using fresh water. (2) if the battery terminals are dirty or corrod- ed, clean them using a wire brush. (3) apply yamalube marine grease to the battery te...
Page 90: Care And Storage
Care and storage 85 eju33492 long-term storage warning ewj00330 always place the watercraft upright in a horizontal position when storing it, other- wise fuel could leak out into the engine or engine compartment, which could create a fire hazard. Storage for long periods of time, such as win- ter st...
Page 91: Care And Storage
Care and storage 86 eju40261 rustproofing spray metallic parts of the hull, deck, and en- gine with a rust inhibitor such as yamaha sil- icone protectant and lubricant. Have a yamaha dealer rustproof the internal engine components. Uf2r12e0.Book page 86 tuesday, july 6, 2010 9:21 am.
Page 92: Maintenance
Maintenance 87 eju33757 maintenance periodic checks and lubrication will keep your watercraft in the safest and most efficient con- dition possible. Therefore, make sure to carry out the periodic maintenance. Safety is an ob- ligation of the watercraft owner. Proper main- tenance must be carried out...
Page 93: Maintenance
Maintenance 88 (3) slide the engine cover toward the stern, and then lift up the cover to remove it. To install the engine cover: (1) place the engine cover in its original posi- tion, push it down, and then slide it toward the bow. (2) install the engine cover screws, and then tighten them to the s...
Page 94: Maintenance
Maintenance 89 eju37062 periodic maintenance chart the periodic maintenance chart gives general guidelines for periodic maintenance. Have a yamaha dealer perform the checks in the following chart. However, maintenance may need to be performed more frequently depending on your operating conditions. I...
Page 95: Maintenance
Maintenance 90 eju36942 engine oil and oil filter warning ewj00340 engine oil is extremely hot immediately af- ter the engine is turned off. Coming in con- tact with or getting any engine oil on your clothes could result in burns. Notice ecj00991 do not run the engine with too much or not enough oil...
Page 96: Specifications
Specifications 91 eju34542 specifications watercraft capacity: maximum people on board: 2 person maximum load capacity: 160 kg (353 lb) dimensions: length: 3370 mm (132.7 in) width: 1230 mm (48.4 in) height: 1160 mm (45.7 in) dry weight: 367 kg (809 lb) performance: maximum fuel consumption: 71.3 l/...
Page 97: Trouble Recovery
Trouble recovery 92 eju34561 troubleshooting if you have any trouble with your watercraft, use the troubleshooting chart to check for the pos- sible cause. If you cannot find the cause, consult a yamaha dealer. Eju36984 troubleshooting chart confirm the possible cause and remedy, and then refer to t...
Page 98: Trouble Recovery
Trouble recovery 93 engine runs irregu- larly or stalls fuel empty refill as soon as pos- sible 51 stale or contaminat- ed have serviced by yamaha dealer — fuel tank water or dirt present have serviced by yamaha dealer — spark plug fouled or defective have serviced by yamaha dealer — incorrect heat ...
Page 99: Trouble Recovery
Trouble recovery 94 watercraft slow or loses power shift lever not completely shift- ed into forward posi- tion push lever forward until it stops 35 watercraft operation mode low rpm mode acti- vated deactivate low rpm mode 37 cavitation jet intake clogged clean 95 impeller damaged or worn have serv...
Page 100: Trouble Recovery
Trouble recovery 95 eju34623 emergency procedures eju34634 cleaning the jet intake and impeller warning ewj00782 before attempting to remove weeds or de- bris from the jet intake or impeller area, shut the engine off and remove the clip from the engine shut-off switch. Severe in- jury or death could...
Page 101: Trouble Recovery
Trouble recovery 96 (2) remove any weeds or debris from around the jet intake, drive shaft, impel- ler, jet pump housing, and jet thrust noz- zle. If debris is difficult to remove, consult a yamaha dealer. Eju34641 jumping the battery if the watercraft battery has run down, the en- gine can be start...
Page 102: Trouble Recovery
Trouble recovery 97 (2) remove the electrical box cover. (3) loosen the cap on the electrical box and remove it. (4) replace the blown fuse with the spare fuse of the correct amperage by using the fuse puller on the reverse side of the cap. Warning! Do not use fuses of a dif- ferent amperage than re...
Page 103: Trouble Recovery
Trouble recovery 98 (7) securely install the seats in their original positions. If the fuse immediately blows again, the elec- trical system may be defective. If this occurs, have a yamaha dealer service the watercraft. Eju41820 replacing the bilge pump fuse if the fuse is blown, replace it with the...
Page 104: Trouble Recovery
Trouble recovery 99 cap. (see page 96 for information on the fuse puller.) (5) securely install the fuse cover, and then fit the bilge pump fuse holder into the rub- ber cover. (6) secure the bilge pump fuse leads and corrugated tube with the plastic ties. (7) securely install the engine cover and s...
Page 105: Trouble Recovery
Trouble recovery 100 tow the watercraft at 8 km/h (5 mph) or less. Notice: tow the watercraft at 8 km/h (5 mph) or less, otherwise water could flood the engine compartment or water could flow back into the engine, causing severe engine damage. [ecj01321] eju36155 submerged watercraft if the watercra...
Page 106: Consumer Information
Consumer information 101 eju34781 limited warranty yamaha motor corporation, u.S.A. Watercraft limited warranty yamaha motor corporation is proud of its heritage and reputation for producing products with high standards of quality and workman- ship. Product excellence provides the cornerstone for ou...
Page 107: Consumer Information
Consumer information 102 this warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Yamaha motor corporation, u.S.A. Post office box 6555 cypress, california 90630 warranty questions and answers q. What costs are my responsibility during the war...
Page 108: Consumer Information
Consumer information 103 eju34800 yamaha extended service (y.E.S.) keep your yamaha protected even after your warranty expires with genuine yamaha extended service (y.E.S.). • y.E.S. Is designed and administered by yamaha motor corporation to provide maximum owner satisfaction. You get uninterrupted...
Page 109: Index
Index a after removing the watercraft from the water ............................................... 80 approval label of emission control certificate ................................................ 2 b battery care.............................................. 82 battery checks.......................
Page 110: Index
Index limitations on who may operate the watercraft ........................................ 10 limited warranty..................................... 101 long-term storage.................................... 85 low rpm mode........................................ 37 lubrication.........................
Page 111
Uf2r12e0.Book page 3 tuesday, july 6, 2010 9:21 am.
Page 112
Printed in usa june 2010–0.4 × 1 cr yamaha motor corporation, usa dic183.