1. DL manuals
  2. Yamaha
  3. Motorcycle
  4. 2011 YZF-R1A
  5. Owner's Manual

Yamaha 2011 YZF-R1A Owner's Manual

Summary of 2011 YZF-R1A

  • Page 1

    Dic183 yzf-r1a owner’s manual read this manual carefully before operating this vehicle. 14b-28199-22.

  • Page 2

    Eau46090 read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold. U14b22e0.Book page 1 monday, july 26, 2010 9:07 am.

  • Page 3

    Introduction eau10102 welcome to the yamaha world of motorcycling! As the owner of the yzf-r1a, you are benefiting from yamaha’s vast experience and newest technology regarding the de- sign and manufacture of high-quality products, which have earned yamaha a reputation for dependability. Please take...

  • Page 4

    Important manual information eau10132 particularly important information is distinguished in this manual by the following notations: this is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injur...

  • Page 5

    Important manual information eau10200 yzf-r1a owner’s manual ©2010 by yamaha motor co., ltd. 1st edition, july 2010 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor co., ltd. Is expressly prohibited. Printed in japan. U14b22e0.Book page 2 monday,...

  • Page 6

    Table of contents location of important labels .............................................1-1 safety information ..................2-1 description ..................................3-1 left view ..........................................3-1 right view ........................................3-2 co...

  • Page 7

    Table of contents checking and lubricating the sidestand ...................................7-29 lubricating the swingarm pivots ...7-30 checking the front fork .................7-30 checking the steering ...................7-31 checking the wheel bearings .......7-31 battery ..........................

  • Page 8

    Location of important labels 1-1 1 eau10384 read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is av...

  • Page 9

    Location of important labels 1-2 1 stationary noise test information tested 99 db(a) at 6250 r/min silencing system : yamaha identification : 14b-1 14b-2 14b-2118g-10 tire information cold tire normal pressure should be set as follows. • up to 90 kg (198 lbs) load front rear : 250 kpa, {2.50 kgf/cm²...

  • Page 10

    2-1 2 safety information eau10287 be a responsible owner as the vehicle’s owner, you are respon- sible for the safe and proper operation of your motorcycle. Motorcycles are single-track vehicles. Their safe use and operation are de- pendent upon the use of proper riding techniques as well as the exp...

  • Page 11

    Safety information 2-2 2 due to excessive speed or under- cornering (insufficient lean angle for the speed). • always obey the speed limit and never travel faster than warrant- ed by road and traffic conditions. • always signal before turning or changing lanes. Make sure that other motorists can see...

  • Page 12

    Safety information 2-3 2 ● do not run engine in poorly venti- lated or partially enclosed areas such as barns, garages, or car- ports. ● do not run engine outdoors where engine exhaust can be drawn into a building through openings such as windows and doors. Loading adding accessories or cargo to you...

  • Page 13

    Safety information 2-4 2 aftermarket parts, accessories, and modifications while you may find aftermarket prod- ucts similar in design and quality to genuine yamaha accessories, recog- nize that some aftermarket accessories or modifications are not suitable be- cause of potential safety hazards to y...

  • Page 14

    Safety information 2-5 2 ● check that the fuel cock (if equipped) is in the “off” position and that there are no fuel leaks. ● point the front wheel straight ahead on the trailer or in the truck bed, and choke it in a rail to pre- vent movement. ● shift the transmission in gear (for models with a ma...

  • Page 15

    Description 3-1 3 eau10410 left view 1,2 3 4,5,6 13 12 11 10 9 7,8 1. Front fork compression damping force adjusting screw (page 4-27) 2. Front fork spring preload adjusting bolt (page 4-27) 3. Coolant reservoir (page 7-14) 4. Fuel injection system fuse (page 7-33) 5. Main fuse (page 7-33) 6. Fuse b...

  • Page 16

    Description 3-2 3 eau10420 right view 1,2,3 4 5,6 8 7 9 10 12 11 13 1. Storage compartment (page 4-26) 2. Luggage strap holder (page 4-31) 3. Helmet holder (page 4-25) 4. Passenger seat lock (page 4-24) 5. Battery (page 7-31) 6. Owner’s tool kit (page 7-2) 7. Fuel tank cap (page 4-21) 8. Front fork ...

  • Page 17

    Description 3-3 3 eau10430 controls and instruments 1 2 3 5 6 7 8 4 1. Clutch lever (page 4-19) 2. Left handlebar switches (page 4-17) 3. Main switch/steering lock (page 4-3) 4. Multi-function meter unit (page 4-9) 5. Front brake fluid reservoir (page 7-24) 6. Right handlebar switches (page 4-17) 7....

  • Page 18

    Instrument and control functions 4-1 4 eau47632 d-mode (drive mode) d-mode is an electronically controlled engine performance system with three mode selections (“std”, “a”, and “b”). Push the drive mode switch “mode” to switch between modes. (see page 4-18 for an explanation of the drive mode switch...

  • Page 19

    Instrument and control functions 4-2 4 ● an immobilizer system indicator light (see page 4-8.) the key with the red bow is used to reg- ister codes in each standard key. Since re-registering is a difficult process, take the vehicle along with all three keys to a yamaha dealer to have them re-reg- is...

  • Page 20

    Instrument and control functions 4-3 4 eau10472 main switch/steering lock the main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. Tip be sure to use the standard key (black bow) for regular use of the vehi...

  • Page 21

    Instrument and control functions 4-4 4 to unlock the steering push the key in, and then turn it to “off” while still pushing it. Eau10941 (parking) the steering is locked, and the taillight, license plate light and auxiliary lights are on. The hazard lights and turn sig- nal lights can be turned on,...

  • Page 22

    Instrument and control functions 4-5 4 eau11060 neutral indicator light “ ” this indicator light comes on when the transmission is in the neutral position. Eau11080 high beam indicator light “ ” this indicator light comes on when the high beam of the headlight is switched on. Eau11254 oil level warn...

  • Page 23

    Instrument and control functions 4-6 4 notice eca10021 do not continue to operate the en- gine if it is overheating. Tip ● for radiator-fan-equipped vehi- cles, the radiator fan(s) automati- cally switch on or off according to the coolant temperature in the ra- diator. ● if the engine overheats, see...

  • Page 24

    Instrument and control functions 4-7 4 display conditions what to do under 39 °c (under 103 °f) message “lo” is displayed. Ok. Go ahead with riding. 40–116 °c (104–242 °f) coolant temperature is dis- played. Ok. Go ahead with riding. Above 117 °c (above 243 °f) coolant temperature flashes. Warning l...

  • Page 25

    Instrument and control functions 4-8 4 eau11534 engine trouble warning light “ ” this warning light comes on or flashes if a problem is detected in the electrical circuit monitoring the engine. If this oc- curs, have a yamaha dealer check the self-diagnosis system. (see page 4-14 for an explanation ...

  • Page 26

    Instrument and control functions 4-9 4 eau47786 multi-function meter unit warning ewa12422 be sure to stop the vehicle before making any setting changes to the multi-function meter unit. Changing settings while riding can distract the operator and increase the risk of an accident. The multi-function...

  • Page 27

    Instrument and control functions 4-10 4 when the key is turned to “on”, the ta- chometer needle sweeps once across the r/min range and then returns to zero r/min in order to test the electrical cir- cuit. Notice eca10031 do not operate the engine in the ta- chometer red zone. Red zone: 13750 r/min a...

  • Page 28

    Instrument and control functions 4-11 4 the split time history displays up to 20 stored split times. The split time history can be displayed either in reverse chro- nological order or by speed. 1. Push the “select” button for at least one second to select the re- verse chronological order mode; “l-2...

  • Page 29

    Instrument and control functions 4-12 4 to reset a tripmeter, select it by push- ing the “select” button, and then push the “reset” button for at least one second. If you do not reset the fuel reserve trip- meter manually, it resets itself automat- ically and the display returns to the prior mode af...

  • Page 30

    Instrument and control functions 4-13 4 transmission gear display this display shows the selected gear. The neutral position is indicated by “ ” and by the neutral indicator light. Throttle opening position display the throttle opening position display shows how much the throttle is being opened. Th...

  • Page 31

    Instrument and control functions 4-14 4 air intake temperature display the air intake temperature display indi- cates the temperature of the air drawn into the air filter case. Turn the key to “on”, and push the “reset” button to switch the coolant temperature display to the air intake temperature d...

  • Page 32

    Instrument and control functions 4-15 4 2. If the engine starts, turn it off and try starting the engine with the standard keys. 3. If one or both of the standard keys do not start the engine, take the vehicle, the code re-registering key and both standard keys to a yamaha dealer and have the stan- ...

  • Page 33

    Instrument and control functions 4-16 4 this function allows you to ad- just the brightness of the indi- cator light to suit your preference. F. Throttle opening position dis- play: this function allows you to choose whether or not to show the throttle opening position display. Tip the display shows...

  • Page 34

    Instrument and control functions 4-17 4 to set the shift timing indicator light de- activation function tip ● the shift timing indicator light de- activation function can be set be- tween 7000 r/min and 15000 r/min. From 7000 r/min to 12000 r/min, the indicator light can be set in in- crements of 50...

  • Page 35

    Instrument and control functions 4-18 4 right eau12370 pass switch “pass” press this switch to flash the head- lights. Eau12400 dimmer switch “ / ” set this switch to “ ” for the high beam and to “ ” for the low beam. Eau12460 turn signal switch “ / ” to signal a right-hand turn, push this switch to...

  • Page 36

    Instrument and control functions 4-19 4 the throttle grip must be completely closed in order to change the drive mode. (see page 4-1 for an explana- tion of each drive mode.) tip ● the mode is set to “std” by de- fault. The “std” mode resets when the key is turned to “off”. ● the selected mode is sh...

  • Page 37

    Instrument and control functions 4-20 4 eau33851 brake lever the brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the handle- bar grip. The brake lever is equipped with a brake lever position adjusting knob. To adjust the distance between the brake ...

  • Page 38

    Instrument and control functions 4-21 4 eau13074 fuel tank cap to open the fuel tank cap open the fuel tank cap lock cover, in- sert the key into the lock, and then turn it 1/4 turn clockwise. The lock will be re- leased and the fuel tank cap can be opened. To close the fuel tank cap 1. Push the fue...

  • Page 39

    Instrument and control functions 4-22 4 3. Wipe up any spilled fuel immedi- ately. Notice: immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteri- orate painted surfaces or plastic parts. [eca10071] 4. Be sure to securely close the fuel tank cap. Warning ewa15151 gaso...

  • Page 40

    Instrument and control functions 4-23 4 eau34072 fuel tank breather/overflow hose before operating the motorcycle: ● check the fuel tank breather/over- flow hose connection. ● check the fuel tank breather/over- flow hose for cracks or damage, and replace it if damaged. ● make sure that the end of th...

  • Page 41

    Instrument and control functions 4-24 4 eau47271 seats passenger seat to remove the passenger seat 1. Insert the key into the seat lock, and then turn it clockwise. 2. Lift the front of the passenger seat and pull it forward. To install the passenger seat 1. Insert the projection on the rear of the ...

  • Page 42

    Instrument and control functions 4-25 4 2. Install the bolts with the hexagon wrench. 3. Insert the hexagon wrench back into its holder on the passenger seat. 4. Install the passenger seat. Tip make sure that the seats are properly secured before riding. Eau47530 helmet holder the helmet holder is l...

  • Page 43

    Instrument and control functions 4-26 4 eau14463 storage compartment the storage compartment is located under the passenger seat. (see page 4-24.) when storing the owner’s manual or other documents in the storage com- partment, be sure to wrap them in a plastic bag so that they will not get wet. Whe...

  • Page 44

    Instrument and control functions 4-27 4 eau47260 rear view mirrors the rear view mirrors of this vehicle can be folded forward for parking in narrow spaces. Fold the mirrors back to their original position before riding. Warning ewa14371 be sure to fold the rear view mirrors back to their original p...

  • Page 45

    Instrument and control functions 4-28 4 rebound damping force the rebound damping force is adjusted on the right front fork leg only. To in- crease the rebound damping force and thereby harden the rebound damping, turn the adjusting screw in direction (a). To decrease the rebound damping force and t...

  • Page 46

    Instrument and control functions 4-29 4 tip although the total number of clicks of a damping force adjusting mechanism may not exactly match the above spec- ifications due to small differences in production, the actual number of clicks always represents the entire adjusting range. To obtain a precis...

  • Page 47

    Instrument and control functions 4-30 4 force and thereby soften the rebound damping, turn the adjusting screw in di- rection (b). Compression damping force compression damping force (for fast compression damping) to increase the compression damping force and thereby harden the compres- sion damping...

  • Page 48

    Instrument and control functions 4-31 4 tip to obtain a precise adjustment, it is ad- visable to check the actual total number of clicks or turns of each damping force adjusting mechanism. This adjustment range may not exactly match the spec- ifications listed due to small differences in production....

  • Page 49

    Instrument and control functions 4-32 4 eau15304 sidestand the sidestand is located on the left side of the frame. Raise the sidestand or lower it with your foot while holding the vehicle upright. Tip the built-in sidestand switch is part of the ignition circuit cut-off system, which cuts the igniti...

  • Page 50

    Instrument and control functions 4-33 4 with the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is set to “ 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? With the engine still running...

  • Page 51

    For your safety – pre-operation checks 5-1 5 eau15596 inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the owner’s manual. Warning ewa11151 failure to inspect or maint...

  • Page 52

    For your safety – pre-operation checks 5-2 5 rear brake • check operation. • if soft or spongy, have yamaha dealer bleed hydraulic system. • check brake pads for wear. • replace if necessary. • check fluid level in reservoir. • if necessary, add recommended brake fluid to specified level. • check hy...

  • Page 53

    For your safety – pre-operation checks 5-3 5 chassis fasteners • make sure that all nuts, bolts and screws are properly tightened. • tighten if necessary. — instruments, lights, signals and switches • check operation. • correct if necessary. — sidestand switch • check operation of ignition circuit c...

  • Page 54

    Operation and important riding points 6-1 6 eau15951 read the owner’s manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your yamaha dealer. Warning ewa10271 failure to familiarize yourself with the controls can lead to loss of con- tr...

  • Page 55

    Operation and important riding points 6-2 6 notice eca11833 if a warning or indicator light does not come on initially when the key is turned to “on”, or if a warning or in- dicator light remains on, see page 4-4 for the corresponding warning and indicator light circuit check. 2. Shift the transmiss...

  • Page 56

    Operation and important riding points 6-3 6 eau16810 tips for reducing fuel con- sumption fuel consumption depends largely on your riding style. Consider the following tips to reduce fuel consumption: ● shift up swiftly, and avoid high en- gine speeds during acceleration. ● do not rev the engine whi...

  • Page 57

    Operation and important riding points 6-4 6 eau17213 parking when parking, stop the engine, and then remove the key from the main switch. Warning ewa10311 ● since the engine and exhaust system can become very hot, park in a place where pedestri- ans or children are not likely to touch them and be bu...

  • Page 58

    Periodic maintenance and adjustment 7-1 7 eau17243 periodic inspection, adjustment, and lu- brication will keep your vehicle in the safest and most efficient condition pos- sible. Safety is an obligation of the vehi- cle owner/operator. The most important points of vehicle inspection, adjust- ment, ...

  • Page 59

    Periodic maintenance and adjustment 7-2 7 eau17361 owner’s tool kit the owner’s tool kit is located under the rider seat. (see page 4-24.) the service information included in this manual and the tools provided in the owner’s tool kit are intended to assist you in the performance of preventive mainte...

  • Page 60

    Periodic maintenance and adjustment 7-3 7 eau46861 tip ● the annual checks must be performed every year, except if a kilometer-based maintenance, or for the uk, a mileage-based maintenance, is performed instead. ● from 50000 km (30000 mi), repeat the maintenance intervals starting from 10000 km (600...

  • Page 61

    Periodic maintenance and adjustment 7-4 7 eau1770c general maintenance and lubrication chart no. Item check or maintenance job odometer reading annual check 1000 km (600 mi) 10000 km (6000 mi) 20000 km (12000 mi) 30000 km (18000 mi) 40000 km (24000 mi) 1 * air filter element • replace. √ 2 clutch • ...

  • Page 62

    Periodic maintenance and adjustment 7-5 7 10 drive chain • check chain slack, alignment and condition. • adjust and lubricate chain with a special o-ring chain lubricant thoroughly. Every 800 km (500 mi) and after washing the motorcycle, riding in the rain or riding in wet areas 11 * steering bearin...

  • Page 63

    Periodic maintenance and adjustment 7-6 7 21 * shock absorber as- sembly • check operation and shock ab- sorber for oil leakage. √ √ √ √ 22 * rear suspension re- lay arm and con- necting arm pivoting points • check operation. √ √ √ √ 23 engine oil • change. • check oil level and vehicle for oil leak...

  • Page 64

    Periodic maintenance and adjustment 7-7 7 eau18680 tip ● air filter • this model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with com- pressed air to avoid damaging it. • the air filter element needs to be replaced more frequently when riding in unu...

  • Page 65

    Periodic maintenance and adjustment 7-8 7 eau18712 removing and installing cowl- ings and panels the cowlings and panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a cowling or panel needs to be re- moved and installed....

  • Page 66

    Periodic maintenance and adjustment 7-9 7 to install a cowling 1. Connect the turn signal light lead coupler. 2. Fit the projections on the cowling into the slots as shown. 3. Install the quick fasteners and the quick fastener screws. Eau47243 cowlings c and d to remove a cowling 1. Remove cowling a...

  • Page 67

    Periodic maintenance and adjustment 7-10 7 to install a cowling 1. Insert the projection into the slot, and then slide the cowling back- ward. 2. Place the cowling in its original po- sition, and then install the quick fastener screws. 3. Install cowling a or b. Eau39062 panels a and b to remove a p...

  • Page 68

    Periodic maintenance and adjustment 7-11 7 eau19652 checking the spark plugs the spark plugs are important engine components, which should be checked periodically, preferably by a yamaha dealer. Since heat and deposits will cause any spark plug to slowly erode, they should be removed and checked in ...

  • Page 69

    Periodic maintenance and adjustment 7-12 7 eau47281 engine oil and oil filter car- tridge the engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter car- tridge replaced at the intervals speci- fied in the periodic maintenance and lubrication cha...

  • Page 70

    Periodic maintenance and adjustment 7-13 7 tip an oil filter wrench is available at a yamaha dealer. 6. Apply a thin coat of clean engine oil to the o-ring of the new oil filter cartridge. Tip make sure that the o-ring is properly seated. 7. Install the new oil filter cartridge with an oil filter wr...

  • Page 71

    Periodic maintenance and adjustment 7-14 7 tip be sure to wipe off spilled oil on any parts after the engine and exhaust sys- tem have cooled down. Notice eca11620 ● in order to prevent clutch slip- page (since the engine oil also lubricates the clutch), do not mix any chemical additives. Do not use...

  • Page 72

    Periodic maintenance and adjustment 7-15 7 3. If the coolant is at or below the minimum level mark, remove the coolant reservoir cover by remov- ing the bolts, remove the coolant reservoir cap, and then add cool- ant to the maximum level mark. Warning! Remove only the coolant reservoir cap. Never at...

  • Page 73

    Periodic maintenance and adjustment 7-16 7 4. Remove the radiator cap. Warning! Never attempt to re- move the radiator cap when the engine is hot. [ewa10381] 5. Remove the coolant drain bolt and its gasket to drain the cooling sys- tem. 6. Remove the coolant reservoir cov- er by removing the bolts, ...

  • Page 74

    Periodic maintenance and adjustment 7-17 7 12. Pour the recommended coolant into the radiator until it is full. 13. Install the radiator cap, start the engine, let it idle for several min- utes, and then turn it off. 14. Remove the radiator cap to check the coolant level in the radiator. If necessar...

  • Page 75

    Periodic maintenance and adjustment 7-18 7 eau44734 checking the engine idling speed check the engine idling speed and, if necessary, have it corrected by a yamaha dealer. Eau21384 checking the throttle grip free play the throttle grip free play should mea- sure 3.0–5.0 mm (0.12–0.20 in) at the inne...

  • Page 76

    Periodic maintenance and adjustment 7-19 7 eau21783 tires to maximize the performance, durabil- ity, and safe operation of your motorcy- cle, note the following points regarding the specified tires. Tire air pressure the tire air pressure should be checked and, if necessary, adjusted before each rid...

  • Page 77

    Periodic maintenance and adjustment 7-20 7 ● the replacement of all wheel and brake-related parts, includ- ing the tires, should be left to a yamaha dealer, who has the necessary professional knowl- edge and experience to do so. ● ride at moderate speeds after changing a tire since the tire surface ...

  • Page 78

    Periodic maintenance and adjustment 7-21 7 ● use only the specified replace- ment tires. Other tires may run the danger of bursting at super high speeds. ● brand-new tires can have a rela- tively poor grip on certain road surfaces until they have been “broken in”. Therefore, it is ad- visable before...

  • Page 79

    Periodic maintenance and adjustment 7-22 7 tip if the specified clutch lever free play cannot be obtained as described above, proceed as follows. 1. Fully turn the adjusting bolt at the clutch lever in direction (a) to loos- en the clutch cable. 2. Loosen the locknut at the crank- case. 3. To increa...

  • Page 80

    Periodic maintenance and adjustment 7-23 7 braking performance, which may re- sult in loss of control and an acci- dent. Eau22273 brake light switches the brake light, which is activated by the brake pedal and brake lever, should come on just before braking takes ef- fect. If necessary, adjust the r...

  • Page 81

    Periodic maintenance and adjustment 7-24 7 wear indicator groove almost appears, have a yamaha dealer replace the brake pads as a set. Eau46291 rear brake pads each rear brake pad is provided with wear indicator grooves, which allow you to check the brake pad wear with- out having to disassemble the...

  • Page 82

    Periodic maintenance and adjustment 7-25 7 ● be careful that water does not en- ter the brake fluid reservoir when refilling. Water will significantly lower the boiling point of the fluid and may result in vapor lock. ● brake fluid may deteriorate paint- ed surfaces or plastic parts. Al- ways clean ...

  • Page 83

    Periodic maintenance and adjustment 7-26 7 4. If the drive chain slack is incorrect, adjust it as follows. Eau34316 to adjust the drive chain slack 1. Loosen the axle nut and the lock- nut on each side of the swingarm. 2. To tighten the drive chain, turn the drive chain slack adjusting bolt on each ...

  • Page 84

    Periodic maintenance and adjustment 7-27 7 eau23025 cleaning and lubricating the drive chain the drive chain must be cleaned and lubricated at the intervals specified in the periodic maintenance and lubrica- tion chart, otherwise it will quickly wear out, especially when riding in dusty or wet areas...

  • Page 85

    Periodic maintenance and adjustment 7-28 7 eau23114 checking and lubricating the throttle grip and cable the operation of the throttle grip should be checked before each ride. In addi- tion, the cable should be lubricated by a yamaha dealer at the intervals speci- fied in the periodic maintenance ch...

  • Page 86

    Periodic maintenance and adjustment 7-29 7 eau23142 checking and lubricating the brake and clutch levers brake lever clutch lever the operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lu- bricated if necessary. Eau23202 checking and lubricati...

  • Page 87

    Periodic maintenance and adjustment 7-30 7 eaum1651 lubricating the swingarm piv- ots the swingarm pivots must be lubricat- ed by a yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart. Eau23272 checking the front fork the condition and operation of the front fo...

  • Page 88

    Periodic maintenance and adjustment 7-31 7 eau23283 checking the steering worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as fol- lows at the intervals specified in the pe- riodic maintenance and lubrication chart. 1. Place a stand under the...

  • Page 89

    Periodic maintenance and adjustment 7-32 7 skin, eyes or clothing and al- ways shield your eyes when working near batteries. In case of contact, administer the fol- lowing first aid. • external: flush with plenty of water. • internal: drink large quan- tities of water or milk and im- mediately call ...

  • Page 90

    Periodic maintenance and adjustment 7-33 7 eau47311 replacing the fuses the main fuse, the fuel injection system fuse, and the fuse boxes, which contain the fuses for the individual circuits, are located under the rider seat. (see page 4-24.) if a fuse is blown, replace it as follows. 1. Turn the ke...

  • Page 91

    Periodic maintenance and adjustment 7-34 7 eau39012 replacing a headlight bulb this model is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows. Notice eca10650 take care not to damage the follow- ing parts: ● headlight bulb do not touch the glass part of the ...

  • Page 92

    Periodic maintenance and adjustment 7-35 7 5. Connect the headlight coupler. 6. Install the headlight bulb cover by turning it clockwise. 7. Have a yamaha dealer adjust the headlight beam if necessary. Eau24181 tail/brake light this model is equipped with an led- type tail/brake light. If the tail/b...

  • Page 93

    Periodic maintenance and adjustment 7-36 7 eau24313 replacing the license plate light bulb 1. Remove the license plate light unit by removing the screws. 2. Remove the license plate light bulb socket (together with the bulb) by pulling it out. 3. Remove the burnt-out bulb by pull- ing it out. 4. Ins...

  • Page 94

    Periodic maintenance and adjustment 7-37 7 4. Insert a new bulb into the socket. 5. Install the auxiliary light bulb sock- et (together with the bulb) by push- ing it in. 6. Install the panel. Eau24350 supporting the motorcycle since this model is not equipped with a centerstand, follow these precau...

  • Page 95

    Periodic maintenance and adjustment 7-38 7 eau24360 front wheel eau34595 to remove the front wheel warning ewa10821 to avoid injury, securely support the vehicle so there is no danger of it falling over. 1. Loosen the front wheel axle pinch bolts, the axle bolt, and then the brake caliper bolts. 2. ...

  • Page 96

    Periodic maintenance and adjustment 7-39 7 5. Install the brake hose holders and reflectors by installing the bolts and nuts. 6. Tighten the axle bolt to the speci- fied torque. Tip while tightening the axle bolt, hold the wheel axle with a 19-mm hexagon wrench to keep it from turning. 7. Tighten wh...

  • Page 97

    Periodic maintenance and adjustment 7-40 7 eau25080 rear wheel eau25314 to remove the rear wheel warning ewa10821 to avoid injury, securely support the vehicle so there is no danger of it falling over. 1. Loosen the axle nut. 2. Lift the rear wheel off the ground according to the procedure on page 7...

  • Page 98

    Periodic maintenance and adjustment 7-41 7 2. Install the drive chain onto the rear sprocket. 3. Install the axle nut, and then lower the rear wheel so that it is on the ground, and then put the sidestand down. 4. Adjust the drive chain slack. (see page 7-25.) 5. Tighten the axle nut, then the lock-...

  • Page 99

    Periodic maintenance and adjustment 7-42 7 eau42502 troubleshooting charts starting problems or poor engine performance check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There is no fuel. Check the compression. Supply fuel. The engine does not start. Check the compression. Operate...

  • Page 100

    Periodic maintenance and adjustment 7-43 7 engine overheating warning ewat1040 ● do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled. ● place a...

  • Page 101

    Motorcycle care and storage 8-1 8 eau37833 matte color caution notice eca15192 some models are equipped with matte colored finished parts. Be sure to consult a yamaha dealer for advice on what products to use be- fore cleaning the vehicle. Using a brush, harsh chemical products or cleaning compounds...

  • Page 102

    Motorcycle care and storage 8-2 8 off any detergent residue using plenty of water, as it is harmful to plastic parts. ● do not use any harsh chemical products on plastic parts or the mufflers. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning produc...

  • Page 103

    Motorcycle care and storage 8-3 8 ● never use compounds or other special treatments to clean the tita- nium mufflers, as they will remove the finish on the outer surface of the mufflers. ● even the smallest amounts of oil, such as from oily towels or finger- prints, will leave stains on the tita- ni...

  • Page 104

    Motorcycle care and storage 8-4 8 eau26203 storage short-term always store your motorcycle in a cool, dry place and, if necessary, protect it against dust with a porous cover. Be sure the engine and the exhaust sys- tem are cool before covering the motor- cycle. Notice eca10810 ● storing the motorcy...

  • Page 105

    Motorcycle care and storage 8-5 8 tip make any necessary repairs before storing the motorcycle. U14b22e0.Book page 5 monday, july 26, 2010 9:07 am.

  • Page 106

    Specifications 9-1 9 dimensions: overall length: 2070 mm (81.5 in) overall width: 715 mm (28.1 in) overall height: 1130 mm (44.5 in) seat height: 835 mm (32.9 in) wheelbase: 1415 mm (55.7 in) ground clearance: 135 mm (5.31 in) minimum turning radius: 3500 mm (137.8 in) weight: curb weight: 206 kg (4...

  • Page 107

    Specifications 9-2 9 2nd: 2.063 (33/16) 3rd: 1.762 (37/21) 4th: 1.522 (35/23) 5th: 1.364 (30/22) 6th: 1.269 (33/26) chassis: frame type: diamond caster angle: 24.00 ° trail: 102.0 mm (4.02 in) front tire: type: tubeless size: 120/70 zr17m/c (58w) manufacturer/model: dunlop/d210f rear tire: type: tub...

  • Page 108

    Specifications 9-3 9 voltage, capacity: 12 v, 8.6 ah headlight: bulb type: halogen bulb bulb voltage, wattage × quantity: headlight: 12 v, 55 w × 2 tail/brake light: led front turn signal light: 12 v, 10.0 w × 2 rear turn signal light: 12 v, 10.0 w × 2 auxiliary light: 12 v, 5.0 w × 2 license plate ...

  • Page 109

    Consumer information 10-1 10 eau48611 identification numbers record the vehicle identification num- ber and model label information in the spaces provided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the vehicle is stolen. Vehicle identification number...

  • Page 110

    Consumer information 10-2 10 eau26570 motorcycle noise regulation (for australia) tampering with noise con- trol system prohibited: owners are warned that the law may prohibit: a. The removal or rendering inopera- tive by any person other than for purposes of maintenance, repair or replacement, of a...

  • Page 111

    Index a air filter element.................................... 7-17 auxiliary light bulb, replacing ................ 7-36 b battery .................................................. 7-31 brake and clutch levers, checking and lubricating ........................................... 7-29 brake and shi...

  • Page 112

    Index t tail/brake light....................................... 7-35 throttle grip and cable, checking and lubricating ........................................... 7-28 throttle grip free play, checking............ 7-18 tires ...................................................... 7-19 tool kit .........

  • Page 113

    U14b22e0.Book page 3 monday, july 26, 2010 9:07 am.

  • Page 114

    Printed on recycled paper yamaha motor co., ltd. Printed in japan 2010.08-0.3 × 1 cr (e) dic183.