Yamaha 212SS 2016 Owner's/operator's Manual

Summary of 212SS 2016

  • Page 1

    2016 yamaha boat 212x 212ss owner’s/operator’s manual f2j-f8199-15 lit-18626-11-02 read this manual carefully before operating this boat. U.S.A. Edition.

  • Page 2

    Read this manual carefully before operating this boat. This manual should stay with the boat if it is sold. Sportsboat_f2j15.Book page 1 monday, may 18, 2015 6:25 pm.

  • Page 3: To The Owner

    Important manual information to the owner thank you for choosing a yamaha boat. This owner’s/operator’s manual contains informa- tion you will need for proper operation, main- tenance, and care. A thorough understanding of these simple instructions will help you to obtain maximum enjoyment from your...

  • Page 4: Table Of Contents

    Table of contents general and important labels.............1 identification number records ........... 1 primary identification (pri-id) number ....................................... 1 hull identification number (hin) ... 1 engine serial numbers .................. 1 emission control information ......

  • Page 5: Table Of Contents

    Table of contents rear underseat storage compartment (port)................... 63 glove compartment..................... 63 port console storage compartment ............................ 64 wet storage compartment........... 65 walk-through .................................. 66 front walk-through ......

  • Page 6: Table Of Contents

    Table of contents trailering ..........................................113 trailering the boat ........................ 113 hitch .......................................... 113 trailering checklist .................... 113 backing your trailer ................... 114 launching..........................

  • Page 7: Engine Serial Numbers

    1 general and important labels identification number records record your primary identification (pri-id) number, hull identification number (hin), and engine serial numbers in the spaces provided to assist you in ordering spare parts from your yamaha boat dealer. Also record and keep these id number...

  • Page 8: Certificate

    General and important labels 2 emission control information these engines conform to u.S. Environmen- tal protection agency (epa) and/or california air resources board (carb) regulations for marine si engines applicable at the time of manufacture. The 4-star labels are affixed to models that meet th...

  • Page 9: Manufactured Date Labels

    General and important labels 3 4-star models 1 emission control information label manufactured date labels these labels are attached to each engine unit. (see page 60 for engine hood opening and closing procedures and page 124 for en- gine cover removal and installation proce- dures.) 1 manufactured...

  • Page 10

    General and important labels 4 stroke engines. These engines are equivalent to the u.S. Epa’s 2006 standards for marine engines. Two stars - very low emission the two-star label identifies engines that meet the air resources board’s personal water- craft and outboard marine engine 2004 ex- haust emi...

  • Page 11: Important Labels

    General and important labels 5 important labels read the following labels before operating this boat. If you need any additional information, contact a yamaha boat dealer. 3 5 13 19 1 4 2 16 15 7 9 6 6 8 sportsboat_f2j15.Book page 5 monday, may 18, 2015 6:25 pm.

  • Page 12: 3-Star Models

    General and important labels 6 10 10 10 14 11 12 10 18 18 3-star models 4-star models 17 17 sportsboat_f2j15.Book page 6 monday, may 18, 2015 6:25 pm.

  • Page 13: Warning Labels

    General and important labels 7 warning labels if any of these labels is damaged or missing, contact a yamaha boat dealer for a replacement. 1 2 3 sportsboat_f2j15.Book page 7 monday, may 18, 2015 6:25 pm.

  • Page 14

    General and important labels 8 4 5 6 7 8 sportsboat_f2j15.Book page 8 monday, may 18, 2015 6:25 pm.

  • Page 15: 212X

    General and important labels 9 improper use of the ballast system can overload the boat, causing poor handling and increased risk of swamping. Ballast system adds 750 lb (340 kg) when full. Include this weight when making sure your load does not exceed the weight shown on the maximum capacities labe...

  • Page 16: Other Labels

    General and important labels 10 other labels this boat complies with u.S. Coast guard safety standards in effect on the date of certification maximum capacities 1740 pounds, persons, gear meets u.S. Epa evap standards using certified components design compliance with nmma requirements is verified. M...

  • Page 17: Safety Information

    11 safety information the safe use and operation of this boat is dependent upon the use of proper operat- ing techniques, as well as upon the com- mon sense, good judgment, and expertise of the operator. Every operator should know the following requirements before operating the boat. ● before operat...

  • Page 18: Safety Information

    Safety information 12 cruising limitations ● scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others. ● operate defensively at safe speeds and keep a safe distance from people, objects, and other watercraft. ● do no...

  • Page 19: Safety Information

    Safety information 13 operational requirements ● all riders must wear a coast guard-ap- proved personal flotation device (pfd). 1 pfd ● eye protection is recommended to keep wind, water, and glare from the sun out of your eyes while you operate your boat. Re- straining straps for eyewear are made wh...

  • Page 20: Safety Information

    Safety information 14 required equipment the u.S. Coast guard (uscg) has regula- tions which describe minimum standards of safety. You must comply with these regula- tions, which apply to boats like your boat which are less than 26 feet long. ● personal flotation devices (pfd): type i, ii, or iii as...

  • Page 21: Safety Information

    Safety information 15 hazard information never start the engines or let them run for any length of time in an enclosed area. Exhaust fumes contain carbon monoxide, a colorless, odorless gas that may cause loss of con- sciousness and death within a short time. Al- ways operate the boat in an open are...

  • Page 22: Safety Information

    Safety information 16 ● keep away from the intake grates while the engines are on. Items such as long hair, loose clothing, or pfd straps can become entangled in moving parts, resulting in se- vere injury or drowning. ● never insert any object into the jet thrust nozzles while the engines are runnin...

  • Page 23: Safety Information

    Safety information 17 wakeboarding and water-skiing you can use the boat to tow the wakeboarder or water-skier, using the ski tow hook provid- ed. It is the boat operator’s responsibility to be alert to the safety of the wakeboarder or wa- ter-skier and others. Know and follow all state and local re...

  • Page 24: Safety Information

    Safety information 18 rules of the road your yamaha boat is legally considered a powerboat. Operation of the boat must be in accordance with the rules and regula- tions governing the waterway on which it is used. Just as there are rules that apply when you are driving on streets and highways, there ...

  • Page 25: Safety Information

    Safety information 19 in the following illustration, your boat is in the center. You should give the right-of-way to any vessels shown in the white area (you are the give-way vessel). Any vessels in the shad- ed area must yield to you (they are the give- way vessels). Both you and the meeting ves- s...

  • Page 26: Safety Information

    Safety information 20 other special situations there are three other rules you should be aware of when operating your boat around other vessels. Narrow channels and bends when navigating in narrow channels, you should keep to the right when it is safe and practical to do so. If the operator of a pow...

  • Page 27: Safety Information

    Safety information 21 this system uses buoys and signs with distinctive shapes and colors to show regulatory or ad- visory information. These markers are white with black letters and orange borders. They signify speed zones, restricted areas, danger areas, and general information. Remember, markings...

  • Page 28: Safety Information

    Safety information 22 to get more boating safety information be informed about boating safety. Additional publications and information can be obtained from many organizations, including the follow- ing. United states coast guard consumer affairs staff (g-bc) office of boating, public, and consumer a...

  • Page 29: Description

    23 description boat glossary term definition bow the front part of the boat. Deck the “floor” or upper structure which covers the hull. Give-way the vessel which must yield the right-of-way when two boats meet. Gunwale the meeting junction of the deck and hull; the upper edge around the boat. Pronou...

  • Page 30: Description

    Description 24 location of main components exterior components 212x 1 bow ladder (page 70) 2 bow light (page 48) 3 front starboard seat (front) (page 57) 4 speaker 5 handrail 6 front starboard seat (rear) (page 57, 61) 7 gps antenna 8 windshield (page 66) 9 driver’s seat (page 58) 10 mirror 11 wakeb...

  • Page 31: Description

    Description 25 212ss 1 bow ladder (page 70) 2 bow light (page 48) 3 front starboard seat (front) (page 57) 4 speaker 5 handrail 6 front starboard seat (rear) (page 57, 61) 7 gps antenna 8 windshield (page 66) 9 driver’s seat (page 58) 10 handgrip 11 bimini top (page 79) 12 rear starboard seat (page ...

  • Page 32: Description

    Description 26 1 cleat 2 swim platform (page 71) 3 beverage holder 4 wet storage compartment (page 65) 5 speaker 6 ski tow hook 7 battery (page 31, 96, 132) 8 rear port seat (page 57, 63) 9 handgrip 10 passenger’s seat (212x) (page 57) 11 passenger’s seat (212ss) (page 57, 59) 12 side table (page 72...

  • Page 33: Description

    Description 27 stern components 1 stern ladder (page 71) 2 stern eye 3 shift gate (page 33) 4 jet thrust nozzle 5 hull drain plug (page 88) 6 water temperature/water depth sensor 7 intake grate 2 1 4 3 2 4 3 6 5 7 7 sportsboat_f2j15.Book page 27 monday, may 18, 2015 6:25 pm.

  • Page 34: Description

    Description 28 helm components 1 blower switch (page 48) 2 main switch (page 32) 3 switch circuit breaker (page 54) 4 multi-function tachometer (page 36) 5 speedometer (page 36) 6 bilge pump switch (page 48) 7 navigation and anchor lights switch (page 48) 8 horn switch (page 49) 9 courtesy light swi...

  • Page 35: Description

    Description 29 engine components 3-star models 1 blower (page 98) 2 fuse box (cover) (page 142) 3 engine oil filler cap (page 85) 4 engine cover (page 124) 5 dipstick (page 85) 6 air filter case (page 128) 7 spark plug/ignition coil 7 6 3 2 1 4 5 sportsboat_f2j15.Book page 29 monday, may 18, 2015 6:...

  • Page 36: Description

    Description 30 4-star models 1 blower (page 98) 2 fuse box (cover) (page 142) 3 engine oil filler cap (page 85) 4 engine cover (page 124) 5 dipstick (page 85) 6 air filter case (page 128) 7 spark plug/ignition coil 1 2 3 4 5 6 7 sportsboat_f2j15.Book page 30 monday, may 18, 2015 6:25 pm.

  • Page 37: Control Function Operation

    31 control function operation boat control functions engine shut-off switch warning ● always attach the engine shut-off cord (lanyard) to your pfd before starting the engines. Failure to attach the cord could result in a runaway boat if the operator is ejected. ● do not attach the cord to clothing t...

  • Page 38: Control Function Operation

    Control function operation 32 main switches there is a main switch for each engine. The main switch controls the ignition and electrical circuits as follows: 1 main switch (port engine) 2 main switch (starboard engine) off: ignition circuit is switched off. The engine can- not be started, but other ...

  • Page 39: Control Function Operation

    Control function operation 33 1 neutral position 2 tde position 3 forward position 4 reverse position 5 shift 6 fully closed 7 throttle 8 fully open tip: this boat is equipped with a “start-in-gear” protection. The engines will not start unless the levers are in the neutral position. This boat uses ...

  • Page 40: Control Function Operation

    Control function operation 34 when the remote control levers are moved farther forward, the shift gates are lifted all the way up. All jet thrust is to the rear, which moves the boat forward. 1 shift gate 2 jet thrust nozzle reverse the shift gates are dropped all the way down over the jet thrust no...

  • Page 41: Control Function Operation

    Control function operation 35 tilt lever warning ● never touch the tilt lever during opera- tion, otherwise the steering wheel could suddenly change position, which may lead to an accident. ● be sure the steering wheel is locked in position after adjustment. If the steering wheel is not locked in po...

  • Page 42: Instrument Operation

    36 instrument operation speedometer the speedometer shows the boat speed. The speedometer starts operating when the starboard engine is started. The speedometer needle will sweep once across the speed range, briefly stopping in the center of the me- ter, and then return to zero. 1 speedometer multi-...

  • Page 43: Instrument Operation

    Instrument operation 37 lcd the lcd can display various types of information. To change the displayed item, push the m button or t button. The displayed item changes in the following order. Tip: *: the display units for the item can be changed. See “1-set units” on page 41 for information on selecti...

  • Page 44: Instrument Operation

    Instrument operation 38 fuel level this display shows the amount of fuel remain- ing in the fuel tank. 1 fuel level water depth this display shows the water depth in feet or meters. 1 water depth battery voltage this display shows the battery voltage of the main battery. 1 battery voltage compass th...

  • Page 45: Instrument Operation

    Instrument operation 39 fuel consumption per gallon or liter this display shows the current fuel consump- tion in miles per gallon or kilometers per liter. 1 fuel consumption per gallon or liter fuel used this display shows the amount of fuel used in gallons or liters. 1 fuel used boat speed this di...

  • Page 46: Instrument Operation

    Instrument operation 40 elevation this display shows the elevation of the boat’s current location in feet or meters. 1 elevation highest speed this display shows the highest speed of the boat in miles per hour or kilometers per hour. 1 highest speed system menu (lcd) the system menu contains the fol...

  • Page 47: Instrument Operation

    Instrument operation 41 1-set units the display units of the lcd can be set to “english” or “metric”. When “english” is selected as the display units of the lcd, values are shown in feet/miles/gallons/degrees fahrenheit. When “metric” is selected as the display units of the lcd, values are shown in ...

  • Page 48: Instrument Operation

    Instrument operation 42 3-backlighting the brightness level of the lcd can be ad- justed. To adjust the brightness: (1) push the m button to decrease the bright- ness or push the t button to increase the brightness. The brightness changes each time a button is pushed. (2) wait approximately 8 second...

  • Page 49: Instrument Operation

    Instrument operation 43 (3) push the m button and t button simulta- neously to save the setting and return to the “1-water depth” display. Then, wait approximately 8 seconds until the lcd returns to the system menu. 6-instr. Diag yamaha boat dealer use these functions to test the meters and check th...

  • Page 50: Instrument Operation

    Instrument operation 44 (6) push the m button or t button to select “am” or “pm”. (7) push the m button and t button simulta- neously to save the time setting, and then wait approximately 5 seconds to return to the system menu. 8-heading/comp. The item that can be selected for the normal display of ...

  • Page 51: Instrument Operation

    Instrument operation 45 to select the font size: (1) push the t button to select “normal” or “large”. 1 “large” font display 1 “normal” font display (2) push the m button or wait approximately 8 seconds to save the setting and return to the system menu. To change the item displayed when the “nor- ma...

  • Page 52: Instrument Operation

    Instrument operation 46 warnings warnings are audible and visual indicators of a fault condition. A warning will be displayed on the lcd. Warnings on the lcd can be ac- knowledged by pressing the m button. Once acknowledged, the message will disappear and be replaced by an “ ” flashing in re- verse ...

  • Page 53: Instrument Operation

    Instrument operation 47 if water is not circulating, something may be clogging the intake grates. Refer to “jet pump clean-out procedure” on page 140. F 1 intake grate notice if the cause of overheating cannot be found and corrected, take special precau- tions to avoid major engine damage while you ...

  • Page 54: Instrument Operation

    Instrument operation 48 switches left side 1 blower switch right side 1 bilge pump switch 2 horn switch 3 navigation and anchor lights switch 4 courtesy light switch 1 ballast switch (212x) 2 no-wake mode/cruise assist switch blower switch push this switch to turn on the blowers to ven- tilate the e...

  • Page 55: Instrument Operation

    Instrument operation 49 1 bow light 1 stern light horn switch push this switch to activate the horn. The horn can be used to signal other boats as required by the “rules of the road”. (see page 18 for more information.) ballast switch (212x) warning ● improper use of the ballast system can overload ...

  • Page 56: Instrument Operation

    Instrument operation 50 1 ballast bladder to fill the ballast water: the ballast system fills and discharges water from a screened fitting located below the wa- terline in the starboard jet pump tunnel. The pump can be operated when the boat is moored or running slowly at a no-wake speed. (1) press ...

  • Page 57: Instrument Operation

    Instrument operation 51 (2) when the boat is on the trailer still at a stern-down angle on the loading ramp, operate the ballast pump again to drain any remaining water. It may be neces- sary to press or lift the ballast bladders to help drain them completely. The ballast system has a manual shut-of...

  • Page 58: Instrument Operation

    Instrument operation 52 the buzzer sounds, the no-wake mode is activated. 1 plus side “ ” tip: the no-wake mode can be set to 3 engine speeds. To adjust the engine speed while the no-wake mode is activated, push the plus side or minus side of the no-wake mode/cruise as- sist switch. To deactivate th...

  • Page 59: Instrument Operation

    Instrument operation 53 the starboard multi-function tachometer, the cruise assist is activated. 1 plus side “ ” 2 minus side “ ” tip: ● once the cruise assist is activated, the set engine speed can be increased by pushing the plus side of the switch or decreased by pushing the minus side. However, ...

  • Page 60: Instrument Operation

    Instrument operation 54 tip: once the reverse rpm control is activated, pushing the plus side of the no-wake mode/cruise assist switch will increase the available engine speed by approximately 500 rpm in 3 stages up to a maximum of 6000 rpm, and pushing the minus side will de- crease the available e...

  • Page 61: Instrument Operation

    Instrument operation 55 accessory outlet there is a 12v dc outlet with a circuit breaker located on the starboard side of the steering wheel. Notice do not use an automotive cigarette lighter or other accessories that get hot because the outlet can be damaged. 1 12v dc outlet 2 circuit breaker stere...

  • Page 62: Instrument Operation

    Instrument operation 56 tip: have anyone else on the boat that may have a smartphone turn off the bluetooth function in their smartphone settings before proceed- ing to step (2). (2) turn on the bluetooth function of the smartphone that is to be paired to the ste- reo system. (3) use the smartphone ...

  • Page 63: Equipment Operation

    57 equipment operation seats warning passengers must always sit in a designat- ed seating area, place feet on the deck, and hold on to the handgrips, handrails, or straps when the boat is in motion. This boat is equipped with the following seats. 1 handrail 2 front port seat (rear) 3 front port seat...

  • Page 64: Equipment Operation

    Equipment operation 58 212x 1 driver’s seat 2 passenger’s seat 3 rear starboard seat 4 rear center seat 5 strap 6 handgrip 7 rear port seat 212ss 1 driver’s seat 2 passenger’s seat 3 rear starboard seat 4 rear center seat 5 strap 6 handgrip 7 rear port seat driver’s seat the driver’s seat can slide ...

  • Page 65: Equipment Operation

    Equipment operation 59 to swivel the seat: (1) extend the slide/swivel lock lever. (2) rotate the lever to starboard (right). (3) swivel the seat to the desired position. If it is too easy or too difficult to rotate the seat, adjust the swivel friction by turning the swivel friction knob in or out. ...

  • Page 66: Equipment Operation

    Equipment operation 60 engine hood the engine hood can be opened to access the engines. The engine hood latch is located under the front of the rear center seat. To open the engine hood, pull the engine hood latch up and lift the engine hood. 1 engine hood 2 engine hood latch to prevent excess water...

  • Page 67: Equipment Operation

    Equipment operation 61 to close the anchor storage compartment: (1) close the anchor storage compartment lid. (2) turn the lock handle and make sure that the lid is securely closed. (3) push the lock handle down. Front underseat storage compartments the front underseat storage compartment (starboard...

  • Page 68: Equipment Operation

    Equipment operation 62 1 drain plug (2) securely install the drain plug in its origi- nal position. Rear underseat storage compartment (starboard) notice 212x: the rear underseat storage com- partments also house the ballast bladders. Be careful not to store items in this area that could be crushed ...

  • Page 69: Equipment Operation

    Equipment operation 63 rear underseat storage compartment (port) warning do not carry any flammable substances in the storage compartment or any heavy or metal items that can damage the battery or cause a short circuit. Sparks or fire could result. Notice 212x: the rear underseat storage com- partme...

  • Page 70: Equipment Operation

    Equipment operation 64 1 glove compartment to close the glove compartment: lower the glove compartment lid, and then push the lid down to securely lock it in place. To lock the glove compartment: (1) close the glove compartment. (2) insert the glove compartment key into the glove compartment knob, a...

  • Page 71: Equipment Operation

    Equipment operation 65 to use the port console storage compartment door as the partition: (1) unfold the door and guide the edge of it into the channel on the driver’s side con- sole. 1 edge 2 channel (2) to hold the door in place, hook the port console storage compartment door latch to the metal ta...

  • Page 72: Equipment Operation

    Equipment operation 66 walk-through front walk-through this boat has a large bow area where two adults can sit comfortably with their legs out- stretched. The front walk-through provides easy access to the bow area from the cabin area. 1 front walk-through rear walk-through the backrest of the rear ...

  • Page 73: Equipment Operation

    Equipment operation 67 to open the windshield: (1) turn the windshield latches to the unlock position, and then open the windshield. (2) unsnap the retaining strap from the strap base, and then snap it onto the wind- shield. Stern light the boat is equipped with a removable stern light. The storage ...

  • Page 74: Equipment Operation

    Equipment operation 68 212ss 1 rear starboard seat 2 rear underseat storage compartment (star- board) (2) remove the stern light from the stern light holder. 212x 1 stern light holder 2 stern light 212ss 1 stern light holder 2 stern light tip: for 212ss, skip steps (3) and (4). (3) slide stern light...

  • Page 75: Equipment Operation

    Equipment operation 69 (4) extend the stern light pole, and then screw stern light stopper a onto the cen- ter section of the pole. 1 stern light stopper a (5) open the cap of the stern light socket, fit the protrusion on the stern light into the slot in the socket, and then install the light into t...

  • Page 76: Equipment Operation

    Equipment operation 70 (4) install the stern light into the stern light holder, and then close the storage com- partment. Bow ladder the bow ladder is located in the anchor stor- age compartment. 1 bow ladder 2 anchor storage compartment 3 retaining strap to use the bow ladder: (1) open the anchor s...

  • Page 77: Equipment Operation

    Equipment operation 71 to stow the bow ladder: (1) open the anchor storage compartment lid. (2) raise the bow ladder, and then pull it rearward completely. (3) fold the bow ladder, and then store it in the anchor storage compartment. (4) snap both retaining straps onto the strap bases to secure the ...

  • Page 78: Equipment Operation

    Equipment operation 72 to use the stern ladder: (1) unhook the stern ladder strap. 1 stern ladder strap (2) pull the stern ladder out completely, and then lower it. 1 stern ladder to stow the stern ladder: (1) raise the stern ladder until it is horizontal, and then push it forward completely. (2) ho...

  • Page 79: Equipment Operation

    Equipment operation 73 1 side table to install the side table, slide the end of the ta- ble pole into the table bracket until it is locked in place. 1 table bracket 2 table pole 3 table bracket knob to remove the side table, pull the table brack- et knob, and then pull the table pole upward. Wakeboa...

  • Page 80: Equipment Operation

    Equipment operation 74 notice do not modify the wakeboard tower to tow from any other point or to carry accesso- ries not designed for it. The wakeboard tower could be damaged. Also, the wake- board tower collapsing feature is intended for storage only. The boat should not be transported or operated...

  • Page 81: Equipment Operation

    Equipment operation 75 (4) lower the wakeboard tower, and then in- stall the short tower storage supports. 1 short tower storage support 2 wakeboard tower to set up the wakeboard tower: (1) remove the short tower storage sup- ports, and then lift the wakeboard tower. (2) while supporting the wakeboa...

  • Page 82: Equipment Operation

    Equipment operation 76 (3) push the snap button and extend each forward support pole until it is locked in place. 1 snap button 2 forward support pole (4) secure each forward support pole to the forward support pole mounting bracket using the lock pin. 1 forward support pole 2 lock pin 3 forward sup...

  • Page 83: Equipment Operation

    Equipment operation 77 storing the bimini top to store the bimini top: (1) while pulling the main pole down slightly, push the snap button, and then extend each forward support pole until it is locked in place to loosen the bimini top. 1 snap button 2 forward support pole (2) remove each forward sup...

  • Page 84: Equipment Operation

    Equipment operation 78 (5) unzip the flaps to remove the bimini top from the wakeboard tower, and then wrap the bimini top around the main pole. 1 flap (6) install the storage cover. Trailering with the bimini top the bimini top must be secured to the boat when it is being trailered. When the boat i...

  • Page 85: Equipment Operation

    Equipment operation 79 installing the bimini top to install the bimini top: when installing the bimini top, simply reverse the removal steps, and then make sure that the lock pins are securely installed. Bimini top (212ss) setting up the bimini top to set up the bimini top: (1) raise the bimini top,...

  • Page 86: Equipment Operation

    Equipment operation 80 (3) remove the storage cover, unfold the bi- mini top, and pull it toward the bow. 1 storage cover (4) hook the latch on each front strap onto the strap eye. 1 front strap 2 latch 3 strap eye (5) tighten the front straps so that the top is snug and wrinkle free. Notice do not ...

  • Page 87: Equipment Operation

    Equipment operation 81 to store the bimini top in the upright position: (1) loosen each front strap, and then un- hook the latch from the strap eye. 1 front strap 2 latch 3 strap eye (2) pull the bimini top toward the stern, and then fold it. 1 bimini top (3) install the storage cover. Notice do not...

  • Page 88: Equipment Operation

    Equipment operation 82 trailering with the bimini top the bimini top must be secured to the boat when it is being trailered. When the boat is trailered with a genuine yamaha boat cover, simply store the bimini top in the fully col- lapsed position and install the storage cover. If a boat cover is no...

  • Page 89: Fuel Requirement

    83 operation and handling requirements fuel requirement fuel warning ● gasoline and gasoline vapors are ex- tremely flammable. To avoid fires and explosions and to reduce the risk of in- jury when refueling, follow these in- structions. ● gasoline is poisonous and can cause in- jury or death. Handle...

  • Page 90: Engine Oil Requirement

    Operation and handling requirements 84 (5) stop filling when the fuel just becomes visible in the bottom of the filler tube. Do not “top off” the tank, because gasoline could spill out. (6) wipe up any spilled fuel immediately. (7) close the fuel tank filler cap by pushing it until it locks in place...

  • Page 91: Warning

    Operation and handling requirements 85 checking the engine oil warning engine oil is extremely hot immediately af- ter the engines are turned off. Coming in contact with or getting any engine oil on your clothes could result in burns. Notice make sure debris and water do not enter the oil filler hol...

  • Page 92: Draining The Bilge Water

    Operation and handling requirements 86 4-star models 1 maximum level mark 2 minimum level mark (5) if the engine oil level is significantly above the maximum level mark, consult a yamaha boat dealer. If the engine oil lev- el is below the minimum level mark, add engine oil. (6) remove the engine oil...

  • Page 93: Bow

    Operation and handling requirements 87 (1) remove the floor mat. 1 fuel tank compartment cover 2 lock handle 3 floor mat (2) pull the lock handles up, and then turn them. (3) remove the fuel tank compartment cover to check the fuel tank compartment for bilge water. (4) open the engine hood. (5) remo...

  • Page 94

    Operation and handling requirements 88 draining the bilge water from the hull remove the hull drain plug at the stern to drain the water. Check the condition of the o-ring on the hull drain plug, and then secure- ly install the drain plug. 1 hull drain plug draining the bilge water on water this mod...

  • Page 95

    Operation and handling requirements 89 1 bilge pump switch 1 bilge water outlet bilge navi anc ctsy lights horn 1 1 sportsboat_f2j15.Book page 89 monday, may 18, 2015 6:25 pm.

  • Page 96: First-Time Operation

    90 first-time operation engine break-in notice failure to perform the engine break-in could result in reduced engine life or even severe engine damage. The engine break-in period is essential to al- low the various components of the engines to wear and polish themselves to the correct op- erating cl...

  • Page 97: Pre-Operation Checks

    91 pre-operation checks warning failure to inspect or maintain the boat properly increases the possibility of an accident or damage to the boat. Do not operate the boat if you find any problem. If a problem cannot be corrected by the procedures provided in this manual, have the boat inspected by a y...

  • Page 98: Pre-Operation Checks

    Pre-operation checks 92 pre-operation check points pre-launch checks perform the pre-launch checks in the pre-op- eration checklist while the boat is on land. Steering system checks make sure the steering wheel is not loose. There should not be any free play, either in- and-out or in rotation. Turn ...

  • Page 99: Pre-Operation Checks

    Pre-operation checks 93 1 shift gate 2 fully open position check that the shift gates are in the fully closed position when the remote control le- vers are in the reverse position. 1 shift gate 2 fully closed position fire extinguisher check as an inboard boat less than 26 feet in length, your boat ...

  • Page 100: Pre-Operation Checks

    Pre-operation checks 94 operating the fire extinguisher a chemical-type fire extinguisher may not help when sprayed into the engine compart- ment through the fire-port™ because that type needs to be aimed directly at the base of the flames to be effective. See below for fire-port™ information. 1 fir...

  • Page 101: Pre-Operation Checks

    Pre-operation checks 95 1 access port cap (3) close the rear platform hatch. Jet intake checks carefully check the jet intakes under the boat for weeds, debris, or anything else that might restrict the intake of water. If the intakes are clogged, cavitation could occur, reducing jet thrust, and poss...

  • Page 102: Pre-Operation Checks

    Pre-operation checks 96 4-star models 1 dipstick 1 maximum level mark 2 minimum level mark battery check make sure that the battery terminals are not damaged and that the battery leads are con- nected properly. Warning! The battery must always be fully charged and in good condition. Loss of battery ...

  • Page 103: Pre-Operation Checks

    Pre-operation checks 97 bilge water check make sure that no bilge water has collected in the engine compartment and the fuel tank compartment. If bilge water has collected in the engine compartment and the fuel tank compartment, drain it. (see page 86 for infor- mation on draining the bilge water.) ...

  • Page 104: Pre-Operation Checks

    Pre-operation checks 98 blower switch check warning gasoline vapors can explode. Before starting the engines, check the engine compartment for gasoline, gasoline va- pors, and loose electrical connections, and then operate the blowers for at least 4 minutes. Do not start the engines or oper- ate the...

  • Page 105: Pre-Operation Checks

    Pre-operation checks 99 1 bow light 2 stern light (3) push the left side of the navigation and anchor lights switch and check that only the stern light comes on. (4) put the navigation and anchor lights switch in the middle position and check that the bow light and stern light are off. (5) remove th...

  • Page 106: Pre-Operation Checks

    Pre-operation checks 100 1 engine shut-off switch 2 clip cooling water pilot outlet check check that water comes out from the pilot out- lets while the engines are running in the wa- ter. If water is not circulating, something may be clogging the intake grates. Refer to “jet pump clean-out procedure...

  • Page 107: Operation

    101 operation driving your boat getting to know your boat operating your boat requires skills acquired through practice over a period of time. Take the time to learn the basic techniques well be- fore attempting more difficult maneuvers. Boating with your new boat can be a very en- joyable activity,...

  • Page 108: Operation

    Operation 102 failure to understand how the controls work could cause an accident or prevent you from avoiding an accident. ● gasoline vapors can explode. Before starting the engines, check the engine compartment for gasoline, gasoline va- pors, and loose electrical connections, and then operate the...

  • Page 109: Operation

    Operation 103 1 blower switch (4) attach the engine shut-off cord (lanyard) to your pfd. Install the cord clip onto the engine shut-off switch by pushing the clip groove over the nut beneath the knob. Be sure the cord is not wrapped around the steering wheel or tangled in the controls. Warning! Chec...

  • Page 110: Operation

    Operation 104 enough throttle should be applied to keep the engine at a fast enough idle to stay running. Stopping the engines warning once the engines have stopped, you have no steering control over the boat. You could collide with another boat, a dock, or other obstacle. Stopping the engines immed...

  • Page 111: Operation

    Operation 105 higher the engine speed, the more thrust is produced. The amount of jet thrust, in addition to the po- sition of the steering wheel, determines how sharply you turn. A. More throttle produces high thrust, so the boat will turn more sharply. B. Less throttle produces low thrust, so the ...

  • Page 112: Operation

    Operation 106 d. If the boat is moving and the remote con- trol levers are in the neutral position, or if there is no thrust because the engines are stopped, the boat will go straight even though the steering wheel is turned. You need throttle to steer. Turning left turning right boating with passen...

  • Page 113: Operation

    Operation 107 stopping the boat warning ● allow adequate stopping distance. ● take early action to avoid collisions. Re- member, boats do not have brakes. ● operate defensively at safe speeds and keep a safe distance away from people, objects, and other boats to give you time to stop. ● do not shut ...

  • Page 114: Operation

    Operation 108 (3) return the stern ladder to the stowed po- sition, and then sit in one of the seats pro- vided. Boarding from the bow a bow ladder is available when boarding from the bow of the boat is desired, when the boat is beached. (see page 70 for bow ladder us- ing procedures.) boarding from...

  • Page 115: Operation

    Operation 109 wind or current pushing boat toward dock: slowly maneuver to a shallow angle and allow the boat to move toward the dock. No wind or current: approach the dock at a shallow angle. Secure the bow to the dock, and then use engine thrust or a boat hook to gently move the stern to the dock....

  • Page 116: Operation

    Operation 110 anchoring warning always anchor from the bow. Anchoring from the stern will make the boat un- steady. A strong current can pull a stern- anchored boat underwater. Select an anchor appropriate for your boat and water conditions. A “danforth” (or fluke) type anchor is suitable for most a...

  • Page 117: Operation

    Operation 111 to cross a wake or swell, change your speed and choose the angle at which you cross the wake or swell. Usually, a slower speed and “quartering” the wake (crossing at an angle) will reduce the jolt. Two other things you may notice. The first is that crossing a group of wakes or swells i...

  • Page 118: Operation

    Operation 112 water, otherwise the engine could overheat and/or seize. (3) stop the engine. (4) wash down the hull, helm, and both jet drive units with fresh water. (5) open the rear platform hatch. (see page 65 for rear platform hatch opening and closing procedures.) (6) remove the access port caps...

  • Page 119: Trailering

    113 trailering trailering the boat warning avoid accident and injury from improper trailering: ● the trailer must be matched for the boat’s weight and hull. ● the towing vehicle must have the capac- ity of pulling the load. Pulling a load that exceeds the towing capacity may cause loss of control. ●...

  • Page 120: Trailering

    Trailering 114 ● secure the bow of the boat to the trailer with the winch line and also with the chain. Se- cure the stern eyes to the trailer with tie- downs. 1 bow eye 1 stern eye ● take down and store the bimini top, if used. The bimini top is not designed to stay unse- cured on the boat at highw...

  • Page 121: Trailering

    Trailering 115 ● turn the towing vehicle’s wheels opposite the direction you want the trailer to go. ● after the trailer begins moving, turn the tow- ing vehicle to follow it. ● have a second person stand by to help di- rect you with hand signals. Launching as a courtesy to other boaters, prepare yo...

  • Page 122: Trailering

    Trailering 116 1 bow eye (6) pull the trailer up the ramp out of the way of other boaters. Attach the bow and stern tie-downs. Reconnect the trailer lights. 1 stern eye (7) perform the post-operation checks on page 111. Lifting notice do not attach lifting cables to the bow eye, cleats, stern eyes, ...

  • Page 123: Care And Storage

    117 care and storage post-operation care flushing the cooling system cooling system flushing is essential to pre- vent the cooling system from clogging up with salt, sand, or dirt. (1) connect the garden hose adapter to a garden hose. 1 garden hose adapter (2) loosen the flush hose connector cap for...

  • Page 124: Care And Storage

    Care and storage 118 cleaning the boat warning gasoline and its vapors are highly flam- mable and explosive. If there is fuel or a fu- el/water mixture in the engine compartment or the fuel tank compart- ment, wipe it up immediately with dry rags. Do not operate the boat until the source of the fuel...

  • Page 125: Care And Storage

    Care and storage 119 (5) open the rear platform hatch. (see page 65 for rear platform hatch opening and closing procedures.) (6) remove the access port caps to let any water drain that has pooled on them. (see page 140 for access port cap re- moval and installation procedures.) if the boat will be s...

  • Page 126: Care And Storage

    Care and storage 120 basic stain guide here are basic steps to remove common stains from boat upholstery. Consult a yamaha boat dealer or upholstery-cleaning professional for difficult stains. * may cause permanent staining. Type of stain steps (rinse with clean, warm water and then dry after applic...

  • Page 127: Care And Storage

    Care and storage 121 battery care if the boat will not be used for more than a month, remove the battery and store it in a cool, dark place. The battery is located in the rear underseat storage compartment (port). To remove the battery: (1) turn the battery switch to the off (red) position. (see pag...

  • Page 128: Care And Storage

    Care and storage 122 long-term storage storing your boat for prolonged periods of time, such as winter storage, requires preven- tative maintenance to ensure against deterio- ration. It is advisable to have the boat serviced by an authorized yamaha boat dealer before storage. However, the following ...

  • Page 129: Care And Storage

    Care and storage 123 ● pivot points grease all pivot points of the steering and shift mechanisms at the pump ends. ● bearing housings grease the bearing housings through the grease nipples. Notice: fill the grease slowly and carefully, because it can dam- age the hoses and the joints. The first serv...

  • Page 130: Maintenance

    124 maintenance maintenance warning be sure to turn off the engines when you perform maintenance unless otherwise specified. If you are not familiar with ma- chine servicing, this work should be done by a yamaha boat dealer or other qualified mechanic. Maintenance, replacement, or repair of the emis...

  • Page 131: Maintenance

    Maintenance 125 (3) lift up the engine cover and remove it. 1 engine cover to install the engine cover: (1) place the engine cover in its original posi- tion, and then push it down. (2) install the engine cover screws, and then tighten them to the specified torque. (3) close the engine hood. Tighten...

  • Page 132: Maintenance

    Maintenance 126 periodic maintenance chart frequency of maintenance operations may be adjusted according to the operating conditions, but the following table gives general guidelines. ● : indicates the checkups which you may do yourself. ■ : indicates work to be done by a yamaha boat dealer. Mainten...

  • Page 133: Maintenance

    Maintenance 127 checking the fuel system warning ● gasoline is highly flammable and explo- sive. Failure to check for and repair any fuel leakage could result in fire or explo- sion. A fire or explosion can cause se- vere injury or death. ● when checking the fuel system, shut off the engines, do not...

  • Page 134: Maintenance

    Maintenance 128 (3) open the rear underseat storage com- partment (port), and then check the fuel filler hose and clamp. 1 fuel filler hose 2 fuel filler hose clamp fuel tank if the fuel tank needs to be cleaned or if any water is found in the fuel system, take the boat to a yamaha boat dealer for s...

  • Page 135: Maintenance

    Maintenance 129 (4) unfasten the hooks, and then remove the air filter case. 1 air filter case 2 hook tip: there are a total of 8 hooks on the top, bot- tom, left side, and right side of the air filter case. (5) remove the screws, and then remove the air filter element. 1 screw 2 air filter element ...

  • Page 136: Maintenance

    Maintenance 130 checking the steering cables to check the steering cables: (1) check for smooth operation of the steer- ing wheel and jet thrust nozzles. (2) check for proper steering adjustment. The nozzles should both point straight back when the steering wheel is cen- tered. If steering is stiff ...

  • Page 137: Maintenance

    Maintenance 131 checking the shift gate mechanisms warning do not touch the shift gates while the re- mote control levers are being operated, otherwise you could be pinched. Check the shift gates for proper operation. (1) remove the engine shut-off cord (lan- yard) and main switch keys. (2) put the ...

  • Page 138: Maintenance

    Maintenance 132 checking the sacrificial anodes an aluminum alloy anode is mounted on each jet pump outlet on your boat. Galvanic corro- sion can damage metal surfaces below the waterline on any boat, particularly in salt wa- ter. These sacrificial anodes are designed to erode in these conditions fi...

  • Page 139: Maintenance

    Maintenance 133 these general guidelines apply to many com- monly used battery types (but not, for exam- ple, to maintenance-free batteries). Consult the battery manufacturer’s instructions before performing battery maintenance. Check the level of the battery fluid and see if the terminals are tight...

  • Page 140: Specifications

    134 specifications specifications item specification boat capacity maximum people on board 9 person maximum load capacity 212x 789 kg (1740 lb) 212ss 835 kg (1840 lb) dimensions and weight length 6500 mm (255.9 in) beam 2600 mm (102.4 in) height 212x 2800 mm (110.2 in) 212ss 1800 mm (70.9 in) draft ...

  • Page 141: Specifications

    Specifications 135 engine number of engines 2 engine type liquid cooled 4-stroke, dohc number of cylinders 4 engine displacement 1812 cm 3 bore × stroke 86.0 × 78.0 mm (3.39 × 3.07 in) compression ratio 11.0 : 1 valve clearance-intake (cold) 0.14–0.23 mm (0.0055–0.0091 in) valve clearance-exhaust (c...

  • Page 142: Specifications

    Specifications 136 fuse amperage electronic throttle valve fuse 10 a fuel pump fuse 10 a main relay drive fuse 10 a main fuse 20 a battery fuse 30 a accessory fuse 20 a, 15 a item specification sportsboat_f2j15.Book page 136 monday, may 18, 2015 6:25 pm.

  • Page 143: Trouble Recovery

    137 trouble recovery troubleshooting if you have any trouble with your boat, use this section to check for the possible cause. If you cannot find the cause or if the procedure for replacement or repair is not described in this own- er’s/operator’s manual, ask your yamaha boat dealer or a qualified m...

  • Page 144: Trouble Recovery

    Trouble recovery 138 trouble possible cause remedy page warning is displayed or flashing in lcd engine overheat warning* jet intake clogged clean 140 cooling system clogged clean 100 oil pressure warning* oil pressure dropped have serviced by yamaha boat dealer — fuel empty refill as soon as possibl...

  • Page 145: Trouble Recovery

    Trouble recovery 139 boat speed too slow or loses power cavitation jet intake clogged clean 140 engine overheat* jet intake clogged clean 140 cooling system clogged clean 100 fuel filter clogged have serviced by yamaha boat dealer — spark plug fouled or defective have serviced by yamaha boat dealer ...

  • Page 146: Trouble Recovery

    Trouble recovery 140 emergency procedures jet pump clean-out procedure warning severe injury or death may result if you ig- nore any of the following: ● turn off and remove both main switch keys, remove the clip from the engine shut-off switch, and wait for all move- ment to stop before removing the...

  • Page 147: Trouble Recovery

    Trouble recovery 141 (5) remove any weeds or debris from the drive shaft, impeller, pump housing, and jet thrust nozzle. If you cannot remove the debris, consult a yamaha boat deal- er. (6) to reinstall the access port cap, first clean off any sand or other foreign matter from the cap or port surfac...

  • Page 148: Trouble Recovery

    Trouble recovery 142 if the boat battery runs down, the engines can be started in an emergency using a 12-volt booster battery and jumper cables. To connect the jumper cables: (1) connect the positive (+) terminal of the dead battery to the positive (+) terminal of the booster battery with the posit...

  • Page 149: Trouble Recovery

    Trouble recovery 143 4-star models 1 fuse box cover 1 electronic throttle valve fuse 2 fuel pump fuse 3 main relay drive fuse 4 main fuse 5 fuse puller 6 battery fuse 7 spare fuse (3) when replacing an accessory fuse, re- move the accessory fuse holder. (see page 63 for rear port seat removal and in...

  • Page 150: Trouble Recovery

    Trouble recovery 144 running on one engine notice do not operate the boat above a no-wake speed with just one engine. Severe engine damage could result be- cause water can flood the non-operating engine through the water intake. If one engine becomes inoperative, the prop- erly running engine can be...

  • Page 151: Consumer Information

    145 consumer information limited warranty yamaha motor corporation, u.S.A. Yamaha boat limited warranty yamaha motor corporation, u.S.A. Hereby warrants that new yamaha boats will be free from defects in materials or workmanship for the period of time stated herein, subject to certain stated limitat...

  • Page 152: Consumer Information

    Consumer information 146 specific parts excluded from warranty; parts replaced due to normal wear or routine maintenance such as oil, spark plugs, fuel filters, impeller and liner, and anodes are not covered by warranty. Charges for transporting the boat to and from an authorized yamaha boat dealer ...

  • Page 153: Consumer Information

    Consumer information 147 customer service if your boat requires warranty service, you must take it to any authorized yamaha boat dealer within the united states. Be sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or problem arises re...

  • Page 154: Consumer Information

    Consumer information 148 yamaha extended service (y.E.S.) keep your yamaha boat protected even after the 1-year warranty coverage provisions expire with genuine yamaha extended service (y.E.S.). Y.E.S. Is designed and administered by yamaha motor corporation to provide maxi- mum owner satisfaction. ...

  • Page 155: Consumer Information

    Consumer information 149 sample float plan leave a float plan with a responsible person on shore before boating. The example below can be copied and used. Float plan vessel information boat make: yamaha motor type: jet model: length: registration no: deck color: hull color: passenger operator addres...

  • Page 156: Index

    150 index a access port cap check ............................. 94 accessory outlet....................................... 55 additional equipment recommendations ................................. 14 air filters, checking ................................. 128 anchor storage compartment.................

  • Page 157: Index

    Index 151 fuel level check ..................................... 100 fuel requirement ...................................... 83 fuel system............................................ 122 fuel system, checking............................ 127 fuel system checks.................................. 95 fu...

  • Page 158: Index

    Index 152 s sample float plan ................................... 149 seats ........................................................ 57 shift gate mechanisms, checking........... 131 side table ................................................. 72 ski locker..............................................

  • Page 159

    For your best ownership experience, think genuine yamaha! Genuine yamaha parts – genuine yamaha replacement parts are the exact same parts as the ones originally equipped on your vehicle, providing you with the performance and durability you have come to expect. Why settle for aftermarket parts that...

  • Page 160

    Printed in usa may 2015–0.3 × 1 cr dic183.