1. DL manuals
  2. Yamaha
  3. Recording Equipment
  4. ACD1
  5. Reference Manual

Yamaha ACD1 Reference Manual

Other manuals for ACD1: Owner's Manual, Service Manual
Manual is about: Amplifier Control Device

Summary of ACD1

  • Page 1

    En reference manual.

  • Page 2: Contents

    Acd1 reference manual 2 contents introduction............................................. 3 about the documentation .................................3 supported amplifiers .........................................3 setup ...................................................................3 terms ......

  • Page 3: Introduction

    Acd1 reference manual 3 introduction about the documentation this document explains mainly the operation and specifications of the acd1 amplifier control device itself. When using the acd1, you will also need to consult various manuals other than this document. ● manuals other than this document • p...

  • Page 4: Terms

    Acd1 reference manual 4 introduction terms this section explains terminology specific to the acd1. ■ amp editor this is computer application software. With this software, you can use your computer to monitor and control the acd1 and the amplifiers connected to the acd1. ■ scene settings such as powe...

  • Page 5: Controls and Connectors

    Acd1 reference manual 5 controls and connectors q display this shows information about the scene, the acd1 itself, or the connected amplifiers. This will light red when an abnormal- ity (a warning or higher alert) occurs. This will also blink blue and white when the identify operation is performed i...

  • Page 6: Rear Panel

    Acd1 reference manual 6 controls and connectors y ground screw the ac power cord is a 3-wire type. If the ac outlet used is earthed (grounded), this device will be properly earthed as well. Also, grounding the screw sometimes reduces hum and interference noise. U [ac in] connector connect to the ac ...

  • Page 7: Panel Operations

    Acd1 reference manual 7 panel operations by pressing buttons on the panel you can monitor or control various parameters of the acd1 itself or of the con- nected amplifiers. The following parameters can be monitored/controlled. Category sub category operation performed 1. Scene (page 10) recall recal...

  • Page 8: Basic Operation

    Acd1 reference manual 8 panel operations the main roles of each button are as follows. As an example, we’ll explain how to store the scene of an amplifier connected to the acd1. The basic operation is the same for all parameters. 1. From the home screen, press the [next] button and then use the [ ▲i...

  • Page 9: 10.

    Acd1 reference manual 9 panel operations 5. Use the [ ▲inc/yes] / [▼dec/no] buttons to select the id of the amplifier for which you want to store settings. 6. Press the [next] button to move to the scene number. 7. Use the [ ▲inc/yes] / [▼dec/no] buttons to select the scene number that you want to s...

  • Page 10: Scene (“1. Scene”)

    Acd1 reference manual 10 panel operations here’s how to recall or store scenes for a specified amplifier. ■ recalling a scene (“1. Scene” ➝ “recall”) recalls a scene for the specified amplifier. • if you select “all” as the amp id, the scene name will not be displayed. • if you select “all” as the a...

  • Page 11

    Acd1 reference manual 11 panel operations these settings allow you to control an amplifier connected to the acd1. ■ power on/standby (“2. Amp control” ➝ “standby”) switches the power of the specified amplifier between on and standby. • if you select “all” as the [amp id], the power supply status may...

  • Page 12

    Acd1 reference manual 12 panel operations this indicates the output level of the amp connected to the acd1. ■ amplifier output (“3. Output monitor”) displays the output level for each channel of the specified amplifier. Here you can make settings to identify the acd1 connected to the network and the...

  • Page 13: Utility (“5. Utility”)

    Acd1 reference manual 13 panel operations ■ identify (“4. Device setup” ➝ “identify”) blinks the “identify” icon of the corresponding acd1 in amp editor. Here you can make overall settings for the acd1 and view various types of information. ■ backup battery check (“5. Utility” ➝ “battery”) displays ...

  • Page 14

    Acd1 reference manual 14 panel operations ■ lcd backlight (“5. Utility” ➝ “lcd backlight”) this specifies the lit status of the acd1’s lcd backlight. ■ restricting panel operations (“5. Utility” ➝ “panel operation”) here you can turns panel operation lock on/off. By locking panel operations you can ...

  • Page 15

    Acd1 reference manual 15 panel operations ■ enabling scene recall operations via emg commands (“5. Utility” ➝ “emg scene setup”) specifies whether the emg scene will be recalled when the emg (emer- gency) signal is received. The following three types of emg signal can be received. • emg command sent...

  • Page 16

    Acd1 reference manual 16 panel operations ■ gpi in calibration (“5. Utility” ➝ “gpi calibration”) calibrates the detected range of the [gpi in] connector input voltage. Here you can make network settings for the acd1. ■ ip address mode setting (“6. Network setup” ➝ “ip address mode”) this specifies ...

  • Page 17: Initializing The Acd1

    Acd1 reference manual 17 panel operations ■ port settings for an external controller (“6. Network setup” ➝ “ip ctrl port #”) here you can specify the port number that will be used to control the acd1 from an external device such as an amx or crestron unit. Here’s how to initialize the acd1’s interna...

  • Page 18: Connector Wiring

    Acd1 reference manual 18 connector wiring this section explains how to wire the [gpi] and [fault output] connectors located on the acd1’s rear panel. Be sure to use the supplied euroblock connector. If you lose the connector, contact your yamaha dealer. 1. Loosen the terminal screws. • use a slotted...

  • Page 19: Gpi Connector

    Acd1 reference manual 19 connector wiring connect gpi (general purpose interface) devices (e.G., control- lers) to the rear panel [gpi] connector. You can use gpi to send or receive control signals to or from an external device. The acd1 provides 4-port input and 4-port output. • the +v terminals ha...

  • Page 20: Fault Output Connector

    Acd1 reference manual 20 connector wiring you can connect a lamp etc. To the rear panel [fault output] connector to indicate that an abnormality has occurred. The [fault output] connector consists of no (normally open), c (common), and nc (normally closed). The [fault output] connector is a relay ci...

  • Page 21: Appendix

    Acd1 reference manual 21 appendix messages that may appear in the acd1’s display and the appropriate responses are listed below. For more about alert messages, refer to the amp editor owner’s manual. The acd1 allows the following single-byte characters to be displayed and input. Display messages mes...

  • Page 22: Troubleshooting

    Acd1 reference manual 22 appendix troubleshooting symptom possible causes response all scene data saved in the acd1 has disap- peared the power was turned off while the acd1’s data was being saved once again synchronize the unit with amp editor to transmit the settings from amp editor. The internal ...

  • Page 23: Control I/o

    Acd1 reference manual 23 appendix *1 supported models xp7000, xp5000, xp3500, xp2500, xp1000, xm4180, xm4080, xh200 guaranteed cable length: 50m *2 supported models t5n, t4n, t3n, pc9501n, pc6501n, pc4801n, pc3301n, pc2001n, pc9500n, pc4800n, pc3300n *3 inputs: 4channels, outputs: 4channels outputs:...

  • Page 24: Dimensions

    Acd1 reference manual 24 appendix unit : mm * specifications and descriptions in this owner’s manual are for information purposes only. Yamaha corp. Reserves the right to change or modify products or specifications at any time without prior notice. Since spec- ifications, equipment or options may no...

  • Page 25

    U.R.G., pro audio division © 2009 yamaha corporation 004-po-d0