- DL manuals
- Yamaha
- Boat
- AR190 2012
- Owner's/operator's Manual
Yamaha AR190 2012 Owner's/operator's Manual
Summary of AR190 2012
Page 1
2012 yamaha boat ar190 sx190 owner’s/operator’s manual f3a-f8199-10 lit-18626-09-43 read this manual carefully before operating this boat. U.S.A. Edition.
Page 2
Read this manual carefully before operating this boat. This manual should stay with the boat if it is sold. Sportsboat.Book page 1 monday, october 24, 2011 8:43 am.
Page 3
Important manual information to the owner thank you for choosing a yamaha boat. This owner’s/operator’s manual contains informa- tion you will need for proper operation, main- tenance, and care. A thorough understanding of these simple instructions will help you to obtain maximum enjoyment from your...
Page 4: Table Of Contents
Table of contents general and important labels........... 1 identification number records ........... 1 primary identification (pri-id) number ....................................... 1 hull identification number (hin) ... 1 engine serial number .................... 1 emission control information ......
Page 5: Table Of Contents
Table of contents equipment operation ...................... 48 seat ................................................ 48 driver’s seat ................................ 48 passenger’s seat (sx190) .......... 50 engine hood ................................... 50 storage compartments .....................
Page 6: Table Of Contents
Table of contents operation............................................87 driving your boat ............................ 87 getting to know your boat ........... 87 learning to operate your boat ..... 87 starting the engine ...................... 87 stopping the engine .................... 89 leavin...
Page 7
1 general and important labels identification number records record your primary identification (pri-id) number, hull identification number (hin), and engine serial number in the spaces provided to assist you in ordering spare parts from your yamaha boat dealer. Also record and keep these id numbers...
Page 8
General and important labels 2 emission control information this engine family conforms to u.S. Environ- mental protection agency (epa) regulations for marine si engines. Approval label of emission control certificate these labels are attached to the engine unit and to the inside of the engine compa...
Page 9
General and important labels 3 manufactured date label this label is attached to the engine unit. (see page 50 for engine hood opening and closing procedures and page 109 for engine cover re- moval and installation procedures.) 1 manufactured date label 1 sportsboat.Book page 3 monday, october 31, 2...
Page 10
General and important labels 4 important labels read the following labels before operating this boat. If you need any additional information, contact a yamaha boat dealer. 9 6 8 7 6 16 3 4 15 5 2 1 14 sportsboat.Book page 4 monday, october 31, 2011 4:12 pm.
Page 11
General and important labels 5 10 13 11 17 18 10 10 10 10 12 sportsboat.Book page 5 monday, october 31, 2011 4:12 pm.
Page 12
General and important labels 6 warning labels if any of these labels is damaged or missing, contact a yamaha boat dealer for a replacement. 1 2 3 sportsboat.Book page 6 monday, october 31, 2011 4:12 pm.
Page 13
General and important labels 7 4 5 6 7 8 sportsboat.Book page 7 monday, october 31, 2011 4:12 pm.
Page 14
General and important labels 8 9 10 11 12 ar190 13 sportsboat.Book page 8 monday, october 31, 2011 4:12 pm.
Page 15: 1160
General and important labels 9 other labels this boat complies with u.S. Coast guard safety standards in effect on the date of certification u.S. Coast guard maximum capacities 1240 pounds, persons, gear meets u.S. Epa evap standards using certified components design compliance with nmma requirement...
Page 16: Safety Information
10 safety information the safe use and operation of this boat is dependent upon the use of proper operat- ing techniques, as well as upon the com- mon sense, good judgment, and expertise of the operator. Every operator should know the following requirements before operating the boat. ● before operat...
Page 17: Safety Information
Safety information 11 cruising limitations ● scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others. ● operate defensively at safe speeds and keep a safe distance from people, objects, and other watercraft. ● do no...
Page 18: Safety Information
Safety information 12 operational requirements ● all riders must wear a coast guard-ap- proved personal flotation device (pfd). 1 pfd ● eye protection is recommended to keep wind, water, and glare from the sun out of your eyes while you operate your boat. Re- straining straps for eyewear are made wh...
Page 19: Safety Information
Safety information 13 required equipment the u.S. Coast guard (uscg) has regula- tions which describe minimum standards of safety. You must comply with these regula- tions, which apply to boats like your boat which are less than 26 feet long. ● personal flotation devices (pfd): type i, ii, or iii as...
Page 20: Safety Information
Safety information 14 hazard information never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monoxide, a colorless, odorless gas that may cause loss of con- sciousness and death within a short time. Al- ways operate the boat in an open area. ...
Page 21: Safety Information
Safety information 15 ● keep away from the intake grate while the engine is on. Items such as long hair, loose clothing, or pfd straps can become entan- gled in moving parts, resulting in severe in- jury or drowning. ● never insert any object into the jet thrust nozzle while the engine is running. S...
Page 22: Safety Information
Safety information 16 water-skiing you can use the boat to tow a water-skier, us- ing the ski tow hook provided. It is the boat operator’s responsibility to be alert to the safety of the water-skier and oth- ers. Know and follow all state and local water- skiing regulations in effect for the waters ...
Page 23: Safety Information
Safety information 17 rules of the road your yamaha boat is legally considered a powerboat. Operation of the boat must be in accordance with the rules and regula- tions governing the waterway on which it is used. Just as there are rules that apply when you are driving on streets and highways, there ...
Page 24: Safety Information
Safety information 18 in the following illustration, your boat is in the center. You should give the right-of-way to any vessels shown in the white area (you are the give-way vessel). Any vessels in the shad- ed area must yield to you (they are the give- way vessels). Both you and the meeting ves- s...
Page 25: Safety Information
Safety information 19 other special situations there are three other rules you should be aware of when operating your boat around other vessels. Narrow channels and bends when navigating in narrow channels, you should keep to the right when it is safe and practical to do so. If the operator of a pow...
Page 26: Safety Information
Safety information 20 this system uses buoys and signs with distinctive shapes and colors to show regulatory or ad- visory information. These markers are white with black letters and orange borders. They signify speed zones, restricted areas, danger areas, and general information. Remember, markings...
Page 27: Safety Information
Safety information 21 to get more boating safety information be informed about boating safety. Additional publications and information can be obtained from many organizations, including the follow- ing. United states coast guard consumer affairs staff (g-bc) office of boating, public, and consumer a...
Page 28: Description
22 description boat glossary term definition bow the front part of the boat. Deck the “floor” or upper structure which covers the hull. Give-way the vessel which must yield the right-of-way when two boats meet. Gunwale the meeting junction of the deck and hull; the upper edge around the boat. Pronou...
Page 29: Description
Description 23 location of main components exterior components ar190 1 cleat 2 handgrip 3 front starboard seat (page 48, 51) 4 windshield (page 56) 5 driver’s seat (page 48) 6 bimini top (page 62) 7 stern light (page 43, 57) 8 tow pylon 9 wakeboard tower (page 60) 10 battery (page 82, 106, 117) 11 b...
Page 30: Description
Description 24 sx190 1 cleat 2 handgrip 3 front starboard seat (page 48, 51) 4 windshield (page 56) 5 driver’s seat (page 48) 6 bimini top (page 67) 7 stern light (page 43, 57) 8 battery (page 82, 106, 117) 9 bow light (page 43) 10 bow eye 11 front center seat (page 48, 51) 12 front port seat (page ...
Page 31: Description
Description 25 1 swim platform (page 59) 2 wet storage compartment (page 55) 3 ski tow hook 4 handgrip 5 rear port seat (page 48, 53) 6 speaker 7 passenger’s seat (ar190) (page 48) 8 passenger’s seat (sx190) (page 48, 50) 9 fuel tank compartment 10 beverage holder 11 accessory outlet (page 47) 12 st...
Page 32: Description
Description 26 stern components 1 ladder (page 59) 2 stern eye 3 hull drain plug (page 74) 4 shift gate (page 31) 5 jet thrust nozzle 6 speed sensor 7 intake grate 1 2 3 5 3 4 2 6 7 sportsboat.Book page 26 monday, october 31, 2011 4:12 pm.
Page 33: Description
Description 27 helm components 1 bilge pump switch (page 42) 2 blower switch (page 42) 3 main switch (page 29) 4 speedometer (page 33) 5 multi-function tachometer (page 33) 6 courtesy light switch (page 43) 7 navigation and anchor lights switch (page 43) 8 horn switch (page 43) 9 no-wake mode/cruise...
Page 34: Description
Description 28 engine components 1 fuse holder (page 125) 2 blower (page 83) 3 engine oil filler cap (page 71) 4 engine cover (page 109) 5 dipstick (page 71) 6 air filter case (page 113) 7 spark plug/spark plug cap/ignition coil 2 1 3 4 6 7 5 sportsboat.Book page 28 monday, october 31, 2011 4:12 pm.
Page 35: Control Function Operation
29 control function operation boat control functions engine shut-off switch warning ● always attach the engine shut-off cord (lanyard) to your pfd before starting the engine. Failure to attach the cord could result in a runaway boat if the operator is ejected. ● do not attach the cord to clothing th...
Page 36: Control Function Operation
Control function operation 30 start: the starter motor will turn to start the engine. (when the main switch key is released, it re- turns automatically to “on”.) tip: the engine will not start when the clip is re- moved from the engine shut-off switch. The starter motor will turn over without the co...
Page 37: Control Function Operation
Control function operation 31 neutral the shift gate is dropped down part way over the jet thrust nozzle. Some jet thrust is to the rear and some jet thrust is redirected forward. This balance of thrust acts like “neutral” to keep the boat from moving. 1 shift gate 2 jet thrust nozzle forward when t...
Page 38: Control Function Operation
Control function operation 32 steering your boat can be steered by turning the steer- ing wheel the same direction you wish to trav- el, to the right or left. When the steering wheel is turned, the angle of the jet thrust nozzle at the rear of the craft is changed, and the change in direction of the...
Page 39: Instrument Operation
33 instrument operation speedometer the speedometer shows the boat speed against water. The speedometer starts operating when the engine is started. The speedometer needle will sweep once across the speed range, briefly stopping in the center of the meter, and then return to zero. 1 speedometer mult...
Page 40: Instrument Operation
Instrument operation 34 lcd the lcd can display 2 of the following 11 items on the upper and lower display lines. 1 lcd 2 upper display line 3 lower display line ● boat speed * ● engine speed ● fuel level ● fuel used * ● battery voltage ● auxiliary battery voltage ● engine hours ● fuel consumption p...
Page 41: Instrument Operation
Instrument operation 35 boat speed this display shows the boat speed against water in miles per hour or kilometers per hour. 1 boat speed engine speed this display shows the engine speed. 1 engine speed fuel level this display shows the amount of fuel remain- ing in the fuel tank. 1 fuel level fuel ...
Page 42: Instrument Operation
Instrument operation 36 fuel consumption per hour this display shows the current fuel consump- tion in gallons per hour or liters per hour. 1 fuel consumption per hour fuel consumption per gallon or liter this display shows the current fuel consump- tion in miles per gallon or kilometers per liter. ...
Page 43: Instrument Operation
Instrument operation 37 1-set units the display units of the lcd can be set to “english” or “metric”. When “english” is selected as the display units of the lcd, values are shown in feet/miles/gallons/degrees fahrenheit. When “metric” is selected as the display units of the lcd, values are shown in ...
Page 44: Instrument Operation
Instrument operation 38 3-backlighting the brightness level of the lcd can be ad- justed. To adjust the brightness: (1) push the m button to decrease the bright- ness or push the t button to increase the brightness. The brightness changes each time a button is pushed. (2) wait approximately 8 second...
Page 45: Instrument Operation
Instrument operation 39 (2) check that the display of lcd is normal, and then wait approximately 8 seconds to return to the “instr. Diag” display. To check the analog inputs: (1) push the m button or t button to select “analog inputs”, and then push the m but- ton and t button simultaneously. (2) to...
Page 46: Instrument Operation
Instrument operation 40 7-large font the font size of the lcd can be set to “nor- mal” or “large”. When “normal” is selected, the normal dis- play of the lcd shows 2 lines of information. When “large” is selected, the normal display of the lcd shows 1 line of information. To select the font size: (1...
Page 47: Instrument Operation
Instrument operation 41 engine overheat warning system this model is equipped with an engine over- heat warning system. If the engine starts to overheat, “engine over temp” will appear on the lcd. The buzzer also begins to sound. The engine speed is automatically limited to help prevent damage. If t...
Page 48: Instrument Operation
Instrument operation 42 engine oil pressure low warning if the oil pressure does not rise to specifica- tion, “low oil press” will appear on the lcd and the buzzer will sound intermittently. At the same time, the engine speed is automatically limited to help prevent damage. If this occurs, reduce th...
Page 49: Instrument Operation
Instrument operation 43 courtesy light switch push this switch to turn on the courtesy light inside the boat. 1 courtesy light navigation and anchor lights switch this toggle switch controls the bow light and stern light. Push the switch up to turn on both the bow light and stern light for night run...
Page 50: Instrument Operation
Instrument operation 44 no-wake mode the no-wake mode is useful for operating the boat at a steady speed with a minimal wake. This is especially convenient when traveling in harbors, channels, or other areas posted with low speed limits as “no wake zones”. The no-wake mode can be used only when the ...
Page 51: Instrument Operation
Instrument operation 45 once “cruise” is displayed in the lcd, the cruise assist is activated. 1 plus side “ ” 2 minus side “ ” tip: ● once the cruise assist is activated, the set engine speed can be increased by pushing the plus side of the switch or decreased by pushing the minus side. However, th...
Page 52: Instrument Operation
Instrument operation 46 tip: once the reverse rpm control is activated, pushing the plus side of the no-wake mode/cruise assist switch will increase the available engine speed by approximately 500 rpm in 3 stages up to a maximum of 6000 rpm, and pushing the minus side will de- crease the available e...
Page 53: Instrument Operation
Instrument operation 47 accessory outlet there is a 12v dc outlet with a circuit breaker located in the glove compartment. Notice do not use an automotive cigarette lighter or other accessories that get hot because the outlet can be damaged. 1 12v dc outlet 2 circuit breaker stereo system a stereo r...
Page 54: Equipment Operation
48 equipment operation seat this boat is equipped with the following seats. 1 front center seat 2 front port seat 3 front starboard seat ar190 1 driver’s seat 2 passenger’s seat 3 rear starboard seat 4 rear center seat 5 rear port seat sx190 1 driver’s seat 2 passenger’s seat 3 rear starboard seat 4...
Page 55: Equipment Operation
Equipment operation 49 (2) rotate the lever to port (left). (3) move the seat to the desired position, and then release the lever. (4) push the lever to its original position. To swivel the seat: (1) extend the slide/swivel lock lever. (2) rotate the lever to starboard (right). (3) swivel the seat t...
Page 56: Equipment Operation
Equipment operation 50 passenger’s seat (sx190) the passenger’s seat can be adjusted in the same ways as the driver’s seat. See “driver’s seat” for instructions on adjust- ing the seat. 1 passenger’s seat engine hood the engine hood can be opened to access the engine. The engine hood latch is locate...
Page 57: Equipment Operation
Equipment operation 51 storage compartments this boat is equipped with the following con- venient on-board storage compartments. Make sure that the storage compartments are securely closed before getting underway. Anchor storage compartment the anchor storage compartment is located under the front c...
Page 58: Equipment Operation
Equipment operation 52 1 ski locker to close the ski locker: (1) close the ski locker lid. (2) turn the lock handle and make sure that the lid is securely closed. (3) push the lock handle down. To drain water from the ski locker: (1) remove the drain plug on the bottom of the ski locker to drain the...
Page 59: Equipment Operation
Equipment operation 53 rear underseat storage compartment (port) the rear underseat storage compartment (port) is located under the rear port seat. Warning do not carry any flammable substances in the storage compartment or any heavy or metal items that can damage the battery or cause a short circui...
Page 60: Equipment Operation
Equipment operation 54 to close the glove compartment: (1) lift the glove compartment lid slightly to release the support spring lock, and then lower the lid. (2) push the lid down to securely lock it in place. Port console storage compartment the port console storage compartment is a large storage ...
Page 61: Equipment Operation
Equipment operation 55 wet storage compartment the wet storage compartment is located un- der the swim platform. To open the wet storage compartment: (1) pull the lock handles up. (2) turn the lock handles 180°, and then open the rear platform hatch. 1 lock handle 2 rear platform hatch 1 wet storage...
Page 62: Equipment Operation
Equipment operation 56 windshield the windshield can be opened and closed. Warning to avoid injury, the windshield must be se- cured when the boat is in motion. To close the windshield: (1) unsnap the retaining strap from the wind- shield, and then snap it onto the strap base. 1 retaining strap 2 st...
Page 63: Equipment Operation
Equipment operation 57 stern light the boat is equipped with a removable stern light. The storage location for the stern light is dif- ferent depending on the model. Ar190: rear underseat storage compartment (starboard) sx190: ski locker to set up the stern light: (1) open the storage compartment. A...
Page 64: Equipment Operation
Equipment operation 58 (3) slide stern light stoppers a and b apart to disconnect them. 1 stern light stopper a 2 stern light stopper b (4) extend the stern light pole, and then screw stern light stopper a onto the cen- ter section of the pole. 1 stern light stopper a (5) open the cap of the stern l...
Page 65: Equipment Operation
Equipment operation 59 to store the stern light: (1) pull stern light stopper b upward, remove the stern light, and then close the cap of the stern light socket. Tip: for sx190, skip steps (2) and (3). (2) unscrew stern light stopper a from the center section of the stern light pole, and then fold t...
Page 66: Equipment Operation
Equipment operation 60 to use the ladder: (1) unhook the ladder strap. 1 ladder strap (2) pull the ladder out completely, and then lower it. 1 ladder to stow the ladder: (1) raise the ladder until it is horizontal, and then push it forward completely. (2) hook the ladder strap onto the ladder. Wakeb...
Page 67: Equipment Operation
Equipment operation 61 notice do not modify the wakeboard tower to tow from any other point or to carry accesso- ries not designed for it. The wakeboard tower could be damaged. Also, the wake- board tower collapsing feature is intended for storage only. The boat should not be transported or operated...
Page 68: Equipment Operation
Equipment operation 62 (3) lower the wakeboard tower, and then in- stall the short tower storage supports. 1 wakeboard tower 1 short tower storage support to set up the wakeboard tower: (1) remove the short tower storage sup- ports, and then lift the wakeboard tower. (2) while supporting the wakeboa...
Page 69: Equipment Operation
Equipment operation 63 (3) push the snap button and extend each forward support pole until it is locked in place. 1 snap button 2 forward support pole (4) secure each forward support pole to the forward support pole mounting bracket using the lock pin. Make sure that the tab on the end of the lock p...
Page 70: Equipment Operation
Equipment operation 64 (7) while pulling the front pole down, push the snap button and shorten each for- ward support pole until it is locked in place to tighten the bimini top. 1 front pole 2 forward support pole 3 snap button notice do not exceed 72 km/h (45 mph) with the bimini top in the up posi...
Page 71: Equipment Operation
Equipment operation 65 (3) wrap the bimini top around the front pole, and then install the storage cover. 1 bimini top 1 storage cover (4) while supporting the front pole, remove each forward support pole from the wake- board tower by removing the lock pin. 1 forward support pole 2 forward support p...
Page 72: Equipment Operation
Equipment operation 66 (6) while supporting the bimini top, hook the forward support poles onto the front pole. 1 bimini top 2 forward support pole (7) pull the bimini top toward the stern, and then fasten the top to the wakeboard tow- er using the buckles. 1 buckle trailering with the bimini top th...
Page 73: Equipment Operation
Equipment operation 67 bimini top (sx190) setting up the bimini top to set up the bimini top: (1) raise the bimini top, and then unhook the rear support poles from the main pole. 1 bimini top 2 rear support pole (2) secure each rear support pole to the rear support pole mounting bracket using the lo...
Page 74: Equipment Operation
Equipment operation 68 (5) tighten the front straps so that the top is snug and wrinkle free. Notice do not exceed 72 km/h (45 mph) with the bimini top in the up position. Storing the bimini top in the upright position notice do not trailer the boat with the bimini top in the fully extended or uprig...
Page 75: Equipment Operation
Equipment operation 69 storing the bimini top in the fully collapsed position to store the bimini top in the fully collapsed position: (1) follow the above steps for “storing the bimini top in the upright position”. (2) while supporting the bimini top, remove the lock pins securing the rear support ...
Page 76
70 operation and handling requirements fuel requirement fuel warning ● gasoline and gasoline vapors are ex- tremely flammable. To avoid fires and explosions and to reduce the risk of in- jury when refueling, follow these in- structions. ● gasoline is poisonous and can cause in- jury or death. Handle...
Page 77
Operation and handling requirements 71 (5) stop filling when the fuel just becomes visible in the bottom of the filler tube. Do not “top off” the tank, because gasoline could spill out. (6) wipe up any spilled fuel immediately. (7) close the fuel tank filler cap by pushing it until it locks in place...
Page 78
Operation and handling requirements 72 notice make sure debris and water do not enter the oil filler hole. Debris and water in the engine oil can cause serious engine dam- age. To check the engine oil level: (1) place the boat in a precisely level position on land with the engine stopped. If the en-...
Page 79
Operation and handling requirements 73 draining the bilge water notice ● do not run the engine at full throttle when bilge water remains in the engine compartment. The bilge water can splash into the engine, which can result in severe damage. ● be sure all drain plugs are tightened be- fore operatin...
Page 80
Operation and handling requirements 74 (8) turn the lock handles, and make sure that the fuel tank compartment cover is securely closed. (9) push the lock handles down. (10) install the floor mat in its original position. Draining the bilge water from the engine compartment if there is fuel or a fue...
Page 81
Operation and handling requirements 75 draining the bilge water on water this model is equipped with a self-draining deck and bilge pump to drain the bilge water on water. Self-draining deck most water which enters the deck area drains automatically out the stern through the large drain hole in the ...
Page 82: First-Time Operation
76 first-time operation engine break-in notice failure to perform the engine break-in could result in reduced engine life or even severe engine damage. The engine break-in period is essential to al- low the various components of the engine to wear and polish themselves to the correct op- erating cle...
Page 83: Pre-Operation Checks
77 pre-operation checks warning failure to inspect or maintain the boat properly increases the possibility of an accident or damage to the boat. Do not operate the boat if you find any problem. If a problem cannot be corrected by the procedures provided in this manual, have the boat inspected by a y...
Page 84: Pre-Operation Checks
Pre-operation checks 78 pre-operation check points pre-launch checks perform the pre-launch checks in the pre-op- eration checklist while the boat is on land. Steering system checks make sure the steering wheel is not loose. There should not be any free play, either in- and-out or in rotation. Turn ...
Page 85: Pre-Operation Checks
Pre-operation checks 79 1 shift gate 2 fully open position check that the shift gate is in the fully closed position when the remote control lever is in the reverse position. 1 shift gate 2 fully closed position fire extinguisher check as an inboard boat less than 26 feet in length, your boat must b...
Page 86: Pre-Operation Checks
Pre-operation checks 80 operating the fire extinguisher a chemical-type fire extinguisher may not help when sprayed into the engine compart- ment through the fire-port™ because that type needs to be aimed directly at the base of the flames to be effective. See below for fire-port™ information. 1 fir...
Page 87: Pre-Operation Checks
Pre-operation checks 81 1 access port cap (3) close the rear platform hatch. Jet intake checks carefully check the jet intake under the boat for weeds, debris, or anything else that might restrict the intake of water. If the intake is clogged, cavitation could occur, reducing jet thrust, and possibl...
Page 88: Pre-Operation Checks
Pre-operation checks 82 battery check make sure that the battery terminals are not damaged and that the battery leads are con- nected properly. Warning! The battery must always be fully charged and in good condition. Loss of battery power may leave you stranded. Never operate the boat if the battery...
Page 89: Pre-Operation Checks
Pre-operation checks 83 1 engine compartment drain plug 1 fuel tank compartment drain plug blower switch check warning gasoline vapors can explode. Before starting the engine, check the engine com- partment for gasoline, gasoline vapors, and loose electrical connections, and then operate the blower ...
Page 90: Pre-Operation Checks
Pre-operation checks 84 push the blower switch to operate the blower and ventilate the engine compartment for at least 4 minutes. Navigation and anchor lights switch check push the navigation and anchor lights switch and check that the bow light and stern light come on. (1) install the stern light. ...
Page 91: Pre-Operation Checks
Pre-operation checks 85 post-launch checks perform the post-launch checks in the pre-op- eration checklist while the boat is in the water and the engine is running. Engine shut-off switch check check the engine shut-off switch for proper operation. (1) start the engine. (see page 87 for infor- matio...
Page 92: Pre-Operation Checks
Pre-operation checks 86 fuel level check select the fuel level display of the multi-func- tion tachometer. (see page 35 for information on selecting the fuel level display.) 1 fuel level add fuel if necessary. (see page 70 for infor- mation on filling the fuel tank.) 1300 rpm f e 1 sportsboat.Book p...
Page 93: Operation
87 operation driving your boat getting to know your boat operating your boat requires skills acquired through practice over a period of time. Take the time to learn the basic techniques well be- fore attempting more difficult maneuvers. Boating with your new boat can be a very en- joyable activity, ...
Page 94: Operation
Operation 88 line vapors in the engine compartment or if there are any loose electrical con- nections. Contact a yamaha boat dealer if there is a problem you cannot locate or correct. ● attach the engine shut-off cord (lanyard) to your pfd before operating. Failure to attach the cord could result in...
Page 95: Operation
Operation 89 off, allowing the boat to continue to run and cause an accident. 1 clip 2 engine shut-off switch 3 engine shut-off cord (lanyard) tip: the engine will not start when the clip is re- moved from the engine shut-off switch. The starter motor will turn over without the cord at- tached. (4) ...
Page 96: Operation
Operation 90 tip: the engine can also be stopped by pulling the engine shut-off cord (lanyard). (3) remove the main switch key and the en- gine shut-off cord (lanyard) if the boat will be left unattended. Leaving a dock because boats steer from the stern, the stern first moves in the direction oppos...
Page 97: Operation
Operation 91 b. Less throttle produces low thrust, so the boat will turn more gradually. C. Pulling the remote control lever back to idle or neutral position produces only minimum thrust. If you are traveling at speeds above trolling, you will have rap- idly decreasing ability to steer without throt...
Page 98: Operation
Operation 92 boating with passengers warning when passengers are on board, make sure they are seated and holding onto the handgrips before you start to accelerate. An unprepared passenger could lose bal- ance and fall. Your boat is designed for one operator and up to seven passengers only. Never hav...
Page 99: Operation
Operation 93 boarding from the water warning to avoid severe injury or death, do not board from the rear, use swim platform, or swim behind boat if engine is running. ● severe internal injuries can occur if wa- ter is forced into body cavities as a re- sult of being near the jet thrust nozzle. ● exh...
Page 100: Operation
Operation 94 wind or current pushing boat away from dock: slowly approach the dock at about a 45° an- gle. Secure the bow to the dock, and then use engine thrust or a boat hook to gently move the stern to the dock. Wind or current pushing boat toward dock: slowly maneuver to a shallow angle and allo...
Page 101: Operation
Operation 95 anchoring warning always anchor from the bow. Anchoring from the stern will make the boat un- steady. A strong current can pull a stern- anchored boat underwater. Select an anchor appropriate for your boat and water conditions. A “danforth” (or fluke) type anchor is suitable for most ap...
Page 102: Operation
Operation 96 to cross a wake or swell, change your speed and choose the angle at which you cross the wake or swell. Usually, a slower speed and “quartering” the wake (crossing at an angle) will reduce the jolt. Two other things you may notice. The first is that crossing a group of wakes or swells is...
Page 103: Operation
Operation 97 (3) stop the engine. (4) wash down the hull, helm, and jet drive unit with fresh water. (5) open the rear platform hatch and remove the access port cap to let any water drain that has pooled on it. (see page 55 for rear platform hatch opening and closing procedures and page 123 for acce...
Page 104: Trailering
98 trailering trailering the boat warning avoid accident and injury from improper trailering: ● the trailer must be matched for the boat’s weight and hull. ● the towing vehicle must have the capac- ity of pulling the load. Pulling a load that exceeds the towing capacity may cause loss of control. ● ...
Page 105: Trailering
Trailering 99 ● secure the bow of the boat to the trailer with the winch line and also with the chain. Se- cure the stern eyes to the trailer with tie- downs. 1 bow eye 1 stern eye ● take down and store the bimini top, if used. The bimini top is not designed to stay unse- cured on the boat at highwa...
Page 106: Trailering
Trailering 100 (1) perform the pre-operation checks shown on page 77 that can be performed on land. (2) remove all trailering tie-down lines from the boat and attach your docking lines and fenders, if used. (3) disconnect the trailer lights from the tow- ing vehicle. (4) back the trailer down the ra...
Page 107: Trailering
Trailering 101 1 stern eye (7) perform the post-operation checks on page 96. Lifting notice do not attach lifting cables to the bow eye, cleats, stern eyes, ski tow hook, or hand- grips. Serious damage to the boat can oc- cur. Use only a sling designed specifically for lifting boats. If you need to ...
Page 108: Care And Storage
102 care and storage post-operation care flushing the cooling system cooling system flushing is essential to pre- vent the cooling system from clogging up with salt, sand, or dirt. (1) connect the garden hose adapter to a garden hose. 1 garden hose adapter (2) loosen the flush hose connector cap and...
Page 109: Care And Storage
Care and storage 103 cleaning the boat warning gasoline and its vapors are highly flam- mable and explosive. If there is fuel or a fu- el/water mixture in the engine compartment or the fuel tank compart- ment, wipe it up immediately with dry rags. Do not operate the boat until the source of the fuel...
Page 110: Care And Storage
Care and storage 104 (5) open the rear platform hatch and remove the access port cap to let any water drain that has pooled on it. (see page 55 for rear platform hatch opening and closing procedures and page 123 for access port cap removal and installation procedures.) if the boat will be stored on ...
Page 111: Care And Storage
Care and storage 105 basic stain guide here are basic steps to remove common stains from boat upholstery. Consult a yamaha boat dealer or upholstery-cleaning professional for difficult stains. * may cause permanent staining. Type of stain steps (rinse with clean, warm water and then dry after applic...
Page 112: Care And Storage
Care and storage 106 battery care if the boat will not be used for more than a month, remove the battery and store it in a cool, dark place. The battery is located in the rear underseat storage compartment (port). To remove the battery: (1) disconnect the negative (–) battery lead (black) and the ne...
Page 113: Care And Storage
Care and storage 107 long-term storage storing your boat for prolonged periods of time, such as winter storage, requires preven- tative maintenance to ensure against deterio- ration. It is advisable to have the boat serviced by an authorized yamaha boat dealer before storage. However, the following ...
Page 114: Care And Storage
Care and storage 108 ● pivot points grease all pivot points of the steering and shift mechanism at the pump end. ● bearing housing grease the bearing housing through the grease nipple. Notice: fill the grease slowly and carefully, because it can dam- age the hose and the joints. The first service sh...
Page 115: Maintenance
109 maintenance maintenance warning be sure to turn off the engine when you perform maintenance unless otherwise specified. If you are not familiar with ma- chine servicing, this work should be done by a yamaha boat dealer or other qualified mechanic. Maintenance, replacement, or repair of the emiss...
Page 116: Maintenance
Maintenance 110 (3) lift up the engine cover and remove it. 1 engine cover to install the engine cover: (1) place the engine cover in its original posi- tion, and then push it down. (2) install the engine cover screws, and then tighten them to the specified torque. (3) close the engine hood. Tighten...
Page 117: Maintenance
Maintenance 111 periodic maintenance chart frequency of maintenance operations may be adjusted according to the operating conditions, but the following table gives general guidelines. ●: indicates the checkups which you may do yourself. ■: indicates work to be done by a yamaha boat dealer. Maintenan...
Page 118: Maintenance
Maintenance 112 checking the fuel system warning ● gasoline is highly flammable and explo- sive. Failure to check for and repair any fuel leakage could result in fire or explo- sion. A fire or explosion can cause se- vere injury or death. ● when checking the fuel system, shut off the engine, do not ...
Page 119: Maintenance
Maintenance 113 (3) open the rear underseat storage com- partment (port), and then check the fuel filler hose and clamp. 1 fuel filler hose clamp 2 fuel filler hose fuel tank if the fuel tank needs to be cleaned or if any water is found in the fuel system, take the boat to a yamaha boat dealer for s...
Page 120: Maintenance
Maintenance 114 (4) unfasten the hooks. 1 air filter case 2 hook tip: there are a total of 8 hooks on the top, bot- tom, left side, and right side of the air filter case. (5) remove the air filter case cover. 1 air filter case cover (6) remove the screws, and then remove the air filter element. 1 sc...
Page 121: Maintenance
Maintenance 115 too much oil, the air filter can become saturated with oil, permanently damag- ing the filter and reducing engine perfor- mance. ● if oil is leaking or “low oil press” ap- pears on the lcd when the engine is running, immediately turn the engine off and have a yamaha boat dealer check...
Page 122: Maintenance
Maintenance 116 checking the shift gate mechanism warning do not touch the shift gate while the re- mote control lever is being operated, oth- erwise you could be pinched. Check the shift gate for proper operation. (1) remove the engine shut-off cord (lan- yard) and main switch key. (2) put the remo...
Page 123: Maintenance
Maintenance 117 checking the sacrificial anode an aluminum alloy anode is mounted on the jet pump outlet on your boat. Galvanic corro- sion can damage metal surfaces below the waterline on any boat, particularly in salt wa- ter. This sacrificial anode is designed to erode first, before metal compone...
Page 124: Maintenance
Maintenance 118 these general guidelines apply to many com- monly used battery types (but not, for exam- ple, to maintenance-free batteries). Consult the battery manufacturer’s instructions before performing battery maintenance. Check the level of the battery fluid and see if the terminals are tight...
Page 125: Specifications
119 specifications specifications item specification boat capacity maximum people on board 8 person maximum load capacity 562 kg (1240 lb) dimensions length 5800 mm (228.3 in) beam 2400 mm (94.5 in) height ar190 2600 mm (102.4 in) sx190 1700 mm (66.9 in) draft (light) 390 mm (15.4 in) draft (heavy) ...
Page 126: Specifications
Specifications 120 drive unit propulsion system jet pump jet pump type axial flow, single stage impeller rotation counterclockwise impeller pitch angle 13.8° transmission direct drive from engine jet thrust nozzle angle 23.0+23.0° jet thrust nozzle trim angle 3° fuel and oil recommended fuel regular...
Page 127: Trouble Recovery
121 trouble recovery troubleshooting if you have any trouble with your boat, use this section to check for the possible cause. If you cannot find the cause or if the procedure for replacement or repair is not described in this own- er’s/operator’s manual, ask your yamaha boat dealer or a qualified m...
Page 128: Trouble Recovery
Trouble recovery 122 *engine speed will be limited to 3500 rpm by the engine overheat warning system. Trouble possible cause remedy page engine runs irregularly or stalls fuel empty refill as soon as possible 70 stale or contaminat- ed have serviced by yamaha boat dealer — fuel filter water or dust ...
Page 129: Trouble Recovery
Trouble recovery 123 emergency procedures jet pump clean-out procedure warning severe injury or death may result if you ig- nore any of the following: ● turn off and remove the main switch key, remove the clip from the engine shut-off switch, and wait for all move- ment to stop before removing the a...
Page 130: Trouble Recovery
Trouble recovery 124 jet thrust nozzle. If you cannot remove the debris, consult a yamaha boat deal- er. (6) to reinstall the access port cap, first clean off any sand or other foreign matter from the cap or port surfaces. (7) insert the access port cap so that its pro- jection faces the bow and lin...
Page 131: Trouble Recovery
Trouble recovery 125 (3) connect the other end of the negative (–) jumper cable to an engine hanger. Notice: be sure all connections are secure and correct before attempting to start the engine. Any wrong con- nection may damage the electrical system. 1 negative (–) jumper cable 2 positive (+) jumpe...
Page 132: Trouble Recovery
Trouble recovery 126 1 accessory fuse holder 2 accessory fuse (4) replace the blown fuse with the spare fuse of the correct amperage by using the fuse puller on reverse side of the cap. (5) install the fuse holder cap. (6) if an accessory fuse was replaced, install the accessory fuse holder. (7) clo...
Page 133: Consumer Information
127 consumer information limited warranty yamaha motor corporation, u.S.A. Yamaha boat limited warranty yamaha motor corporation, u.S.A. Hereby warrants that new yamaha boats will be free from defects in materials or workmanship for the period of time stated herein, subject to certain stated limitat...
Page 134: Consumer Information
Consumer information 128 specific parts excluded from warranty; parts replaced due to normal wear or routine maintenance such as oil, spark plugs, fuel filters, impeller and liner, and anodes are not covered by warranty. Charges for transporting the boat to and from an authorized yamaha boat dealer ...
Page 135: Consumer Information
Consumer information 129 customer service if your boat requires warranty service, you must take it to any authorized yamaha boat dealer within the united states. Be sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or problem arises re...
Page 136: Consumer Information
Consumer information 130 yamaha extended service (y.E.S.) keep your yamaha boat protected even after the 1-year warranty coverage provisions expire with genuine yamaha extended service (y.E.S.). Y.E.S. Is designed and administered by yamaha motor corporation to provide maxi- mum owner satisfaction. ...
Page 137: Consumer Information
Consumer information 131 sample float plan leave a float plan with a responsible person on shore before boating. The example below can be copied and used. Float plan vessel information boat make: yamaha motor type: jet model: length: registration no: deck color: hull color: passenger operator addres...
Page 138: Index
Index a access port cap check ............................. 80 accessory outlet....................................... 47 additional equipment recommendations ................................. 13 air filter, checking................................... 113 anchor storage compartment.....................
Page 139: Index
Index g getting to know your boat ........................ 87 glossary, boat .......................................... 22 glove compartment.................................. 53 grease points......................................... 107 h hazard information................................... 14 high...
Page 140: Index
Index s sample float plan ................................... 131 seat.......................................................... 48 shift gate mechanism, checking ............ 116 ski locker.................................................. 51 specifications ............................................
Page 141
For your best ownership experience, think genuine yamaha! Genuine yamaha parts – genuine yamaha replacement parts are the exact same parts as the ones originally equipped on your vehicle, providing you with the performance and durability you have come to expect. Why settle for aftermarket parts that...
Page 142
Printed in usa november 2011–0.9 × 1 cr dic183.