Yamaha AR210 Owner's/operator's Manual

Summary of AR210

  • Page 1

    Lit-18626-09-42 ©2011 yamaha motor corporation, u.S.A. Printed in u.S.A. Ar/sx 210 owne r ’s /o p e r at o r’s m a nu a l warning read this manual carefully before operating this boat. Ar/sx 210 owner’s/operator’s manual.

  • Page 2

    Read this manual carefully before operating this boat. This manual should stay with the boat if sold. Warning the engine exhaust from this product contains chemicals known to the state of california to cause cancer, birth defects or other reproductive harm. Yamaha lit-calif-65-01.

  • Page 3

    Thank you for choosing a yamaha boat. This owner’s manual contains informa- tion you will need for proper operation, maintenance, and care. A thorough understanding of these simple instruc- tions will help you to obtain maximum enjoyment from your new yamaha. If you have any questions about the oper...

  • Page 5: Ar210/sx210

    2 f eatures & f unctions 1 s afety i nformation 3 o peration 4 m aintenance & c are 5 t rouble r ecovery 6 c onsumer i nformation 1-color pms 287 (2-d) 1-color black (2-d) 1-color pms 287 (reverse 2-d) 1-color black (reverse 2-d) 4-color blue (3-d) 12/98 yamaha logo ar210/sx210

  • Page 7

    # chapter 1 safety information identification number records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 primary i.D. Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 hull identification number (h.I.N.) . . . . . . . . . . . . . . . . . . ....

  • Page 9

    1-1 identification number records record your primary i.D., h.I.N., and engine numbers in the spaces provided to assist you in ordering spare parts from your yamaha boat dealer. Also record and keep these i.D. Numbers in a separate place in case your boat is stolen. Primary i.D. Number the primary i...

  • Page 10

    # s afety i nformation 1-2 emission control information this engine family conforms to u.S. Epa regulations for marine si engines. Approval label of emission control certificate this label is attached to the cylinder head. Emission control information label manufactured date label manufactured date ...

  • Page 11

    S afety i nformation # 1-3 important labels read the following labels before operating this boat. If you need any additional information, contact a yamaha dealer. 1.

  • Page 12

    # s afety i nformation 1-4 if any of these labels is damaged or missing, contact a yamaha dealer for a replacement. 1.

  • Page 13

    S afety i nformation # 1-5 carbon monoxide (co) can cause brain damage or death. Engine and generator exhaust contains odorless and colorless carbon monoxide gas. Carbon monoxide will be around the back of the boat when engines or generators are running. Move to fresh air if you feel nausea, headach...

  • Page 14

    # s afety i nformation 1-6 f2k 1670 vonore, tn tennesee watercraft inc., this boat complies with u.S. Coast guard safety standards in effect on the date of certification national marine manufacturers association other labels 1.

  • Page 15

    S afety i nformation # 1-7 safety information the safe use and operation of this boat is dependent upon the use of proper operating techniques, as well as upon the common sense, good judgment, and expertise of the oper- ator. Every operator should know the following requirements before operating the...

  • Page 16

    # s afety i nformation 1-8 required equipment the u.S. Coast guard (uscg) has regulations which describe minimum standards of safety. You must comply with these regulations, which apply to boats like your boat which are less than 26 feet long. • personal flotation devices (pfds): uscg-approved pfds ...

  • Page 17

    S afety i nformation # 1-9 cruising limitations • scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others. • operate defensively at safe speeds and keep a safe distance from peo- ple, objects, and other watercraft. ...

  • Page 18

    # s afety i nformation 1-10 operational requirements • all riders must wear a coast guard approved personal flotation device (pfd). • eye protection is recommended to keep wind, water, and glare from the sun out of your eyes while you oper- ate your boat. Restraining straps for eyewear are made whic...

  • Page 19

    S afety i nformation # 1-11 • attach the engine shut-off cord (lan- yard) to the pfd and keep it free from the steering wheel or other controls so that the engine stops if the operator accidentally leaves the helm. Failure to attach the engine shut-off cord could result in a run- away boat if the op...

  • Page 20

    # s afety i nformation 1-12 an open area without obstructions until you have a good feel for the maneuver. • this yamaha boat is water-jet pro- pelled. The pumps are directly con- nected to the engines. This means that the jet thrust will produce some movement whenever the engines are running. The b...

  • Page 21

    S afety i nformation # 1-13 water-skiing you can use the boat to tow a water skier, using the tow cleat provided. It is the boat operator’s responsibility to be alert to the safety of the water-skier and others. Know and follow all state and local water-skiing regulations in effect for the waters in...

  • Page 22

    # s afety i nformation 1-14 rules of the road your yamaha boat is legally considered a powerboat. Operation of the boat must be in accordance with the rules and regulations governing the water- way on which it is used. Just as there are rules that apply when you are driving on streets and high- ways...

  • Page 23

    S afety i nformation # 1-15 rules when encountering vessels there are three main situations that you may encounter with other vessels which could lead to a collision unless the steering rules are followed: meeting: you are approaching another vessel head-on. Crossing: you are traveling across anothe...

  • Page 24

    # s afety i nformation 1-16 overtaking if you are passing another vessel, you are the give-way vessel. This means that the other vessel is expected to maintain its course and speed. You must stay out of its way until you are clear of it. Likewise, if another vessel is passing you, you should maintai...

  • Page 25

    S afety i nformation # 1-17 “1” “3” “5” “7” lighted buoy (port hand) odd number, increasing toward head of navigation. Leave to port (left) pro- ceeding white green light light or old new “2” “4” “6” lighted buoy (starboard hand) even number, increasing toward head of navigation. Leave to starboard ...

  • Page 26

    # s afety i nformation 1-18 reading buoys and other markers the waters of the united states are marked for safe navigation by the lat- eral system of buoyage. Simply put, buoys and markers have an arrange- ment of shapes, colors, numbers, and lights to show which side of the buoy a boater should pas...

  • Page 27

    S afety i nformation # 1-19 to get more boating safety information be informed about boating safety. Additional publications and information can be obtained from many organiza- tions, including the following. United states coast guard consumer affairs staff (g-bc) office of boating, public, and cons...

  • Page 29

    Chapter 2 features & functions location of main components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 operation of controls and other functions. . . . . . . . . . . . . . 2-5 steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2...

  • Page 31

    2-1 location of main components f eatures & f unctions 2 main features: fuel tank battery blower motor port/starboard features: flush attachments electrical boxes oil tanks oil tank cap/ dipstick mufflers water lock spark plugs/ coils air filter cases engine compartment vent outlets engine compartme...

  • Page 32

    2-2 2 f eatures & f unctions.

  • Page 33

    2-3 f eatures & f unctions 2 location of main components: bow lights bow eye storage compartments bow anchor locker grab handles cleats courtesy light fuel tank inspection access hatch throttle/shift levers cooler stern light storage stern light socket ski tow hook jet pump clean-out access panel pu...

  • Page 34

    2-4 2 f eatures & f unctions control features: speedometer tachometer multi-function gauge lcd ignition switch keys steering wheel tilt adjustment lever switches and breakers location of main components port starboard control features: hull drain speedometer pick-up steering nozzle reverse gates lad...

  • Page 35

    2-5 f eatures & f unctions 2 operation of controls and other functions steering steering wheel your boat can be steered by turning the steering wheel the same direction you wish to travel, to the right or left. When the wheel is turned, the angle of the jet (output) nozzles at the rear of the craft ...

  • Page 36

    2-6 engine shut-off switch • always attach the engine shut- off cord to your personal flota- tion device (pfd) or arm or leg, before starting the engines. Failure to attach the cord could result in a runaway boat if the operator is ejected. • do not attach the cord to cloth- ing that could tear loos...

  • Page 37

    2-7 off: ignition circuits are switched off. The engine cannot be started but other switches will operate. (the key can be removed.) on: ignition circuits are switched on. (the key cannot be removed). Start: the starter motor will turn to start the engine. (when the key is released, it returns autom...

  • Page 38

    2-8 2 f eatures & f unctions this boat is equipped with “start-in- gear” protection. The engines will not start unless the levers are in the neutral position. The shift lever controls the direction of travel. The drive line on the boat is direct drive, so jet thrust is always being pro- duced while ...

  • Page 39

    2-9 f eatures & f unctions 2 fuel tank filler cap to open the fuel tank filler cap, press the button on the bottom of the cap to release the latch. Fuel tank filler cap press down on the cap until it locks in place. Gauges the boat is equipped with a speedometer and two multi-function tachometers . ...

  • Page 40

    2-10 2 f eatures & f unctions pushbutton wake up mode: refers to the state when both engines are off, the gauges are shut down, and the operator pushes the “ m” button to see the clock. This mode only lasts for 5 seconds and then enters sleep mode power up and basic function: the gauge system will p...

  • Page 41

    2-11 f eatures & f unctions 2 2) contrast: adjust the contrast of the lcd. • press the m button to decrease contrast or the t button to increase contrast. • to exit, simply do nothing. 3) backlighting: adjust the bright- ness of the gauge system back- lighting. • press the m button to decrease brigh...

  • Page 42

    2-12 2 f eatures & f unctions 2 warnings warnings are audible and / or visual indicators of a fault condition. A warning will be displayed on the master gauge lcd. Warnings on the lcd can be acknowledged by pressing the m but- ton. Once acknowledged the message will disappear and be replaced by an “...

  • Page 43

    2-13 f eatures & f unctions 2 warning definition table warning lcd display audible engine overheating engine over temperature y engine oil pressure low low oil press y check engine check engine y low battery voltage low voltage y high battery voltage high voltage y engine overheat warning system thi...

  • Page 44

    2-14 2 f eatures & f unctions switches blower bilge pump courtesy lights lights horn no-wake mode (port) no-wake mode (starboard) blower press this switch to turn on the blower to ventilate the engine compartment. See page 3-9 for more information. Bilge pump press this switch to activate the bilge ...

  • Page 45

    2-15 f eatures & f unctions 2 to set no-wake mode: press both black no-wake mode but- tons simultaneously until the lcd indi- cates “no wake mode” in the meter. Tip: although each engine is controlled separately, always put both engines in no-wake mode for proper operation. To cancel the no-wake mod...

  • Page 46

    2-16 2 f eatures & f unctions tip: there is also an accessory fuse at the battery (see page 4-15). Swivel seat operation the driver’s and mid-ship passenger’s seats are two-way adjustable. To move the seat forward or back, pull up on the lever located under the front of the seat. Move the seat to th...

  • Page 47

    2-17 f eatures & f unctions 2 engine hood there is one hood latch located under the front of the rear seat. To open the engine hood, lift the latch hook upward and lift the hood. Hood latch storage compartments your boat has convenient on-board storage areas. Bow anchor storage under front seats pul...

  • Page 48

    2-18 2 f eatures & f unctions glove box port-side console under rear side seats do not carry any flammable sub- stances in the battery compartment or any heavy or metal items that can damage the battery or cause a short circuit. Sparks or fire could result. Pull up the seat cushions to access the st...

  • Page 49

    2-19 f eatures & f unctions 2 front walk-through if desired, the walk-through to the bow of the boat can be closed. Doorway unlatch the bi-fold door from the port- side console by pulling the rubber latch. Unfold the door and guide the edge of it into the channel on the driver’s side helm console. T...

  • Page 50

    2-20 2 f eatures & f unctions rear walk-through for easy access from the cabin area to the stern patio area and swim platform, lift out and stow the center rear seat cushion. Press the center seat cushion firmly into place for seating when underway. Swim platform stay away from the swim platform are...

  • Page 51

    S afety i nformation # 2-21 collapsing the wakeboard tower the wakeboard tower can be col- lapsed for boat storage in a building or under a canopy or carport. • accidentally dropping the upper tower section while collapsing or raising it can damage the tower, the boat, or both. An assistant needs to...

  • Page 52

    # s afety i nformation 2-22 short tower storage support raising 1) while an assistant holds the upper tower section in the middle, remove the knobs from the top end of the short tower storage supports on each side. 2) remove the inboard-side knobs from the bottom end of the short tower storage suppo...

  • Page 53

    Chapter 3 operation fuel and oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 engine oil . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 55

    3-1 o peration 3 fuel and oil gasoline • gasoline and gasoline vapors are extremely flammable. To avoid fires and explosions and to reduce the risk of injury when refueling, follow these instructions. • gasoline is poisonous and can cause injury or death. Handle gasoline with care. Never siphon gaso...

  • Page 56

    3-2 3 o peration additive, available from your yamaha dealer, is formulated to remove existing deposits and, when used continuously, prevent new ones from forming, while also helping to keep fuel injectors and other fuel system components clean for proper performance and longer engine life. Engine o...

  • Page 57

    3-3 o peration 3 2) if the level is at least at the minimum level “l” mark on the dipstick, but less than the “f” mark , the engine can be operated. Notice: if the level is above the “f” mark, the engine is overfilled. Consult a yamaha dealer to have oil extracted from the engine to avoid damage. 3)...

  • Page 58

    3-4 3 o peration pre-operation checks check list before operating this boat, perform the checks in the following check list. Always follow the inspection and maintenance procedures and schedules described in this owner’s/operator’s manual. Failure to inspect or maintain the boat properly increases t...

  • Page 59

    3-5 o peration 3 tip: pre-operation checks should be made each time the boat is used. These checks can be completed in a short time. It is worth the time spent to ensure safety and reliability. Check points steering make sure the wheel is not loose. There should not be any free play, either in- and-...

  • Page 60

    3-6 fire extinguishers make sure at least one fire extinguisher is aboard and full. See the instructions supplied by the extinguisher manufac- turers to determine indication of condi- tion. As an inboard boat less than 26 feet in length, your boat must be fitted with one b-1 type fire extinguisher w...

  • Page 61

    3-7 o peration 3 oxygen to the fire, increasing the risk of a larger fire or an explosion. If you see smoke or otherwise sus- pect a fire, you can look through the transparent flaps of the fire port™ to look for signs of flames. If there is a fire, push the nozzle of the fire extin- guisher through ...

  • Page 62

    3-8 2) open the engine hatch, then check oil level in the engines. Add as nec- essary (see page 3-2). Battery check the battery condition and the battery electrolyte level. Make sure con- nections are tight and that battery is properly secured. Warning! The bat- tery must always be fully charged and...

  • Page 63

    3-9 o peration 3 flushing the engine area with fresh water after salt water operation. • excessive water in the engine compartment bilge can splash into the air cleaner and engine. This could cause engine damage. • be sure all drain plugs are tight- ened before operating your boat. If a fuel or fuel...

  • Page 64

    3-10 3 o peration if the stern light is not installed, remove it from the storage area, lift the socket cover, and install it into the socket to check operation. Horn press the horn switch to be sure the horn operates. Engine shut-off switch engine shut-off switch clip with cord first, place the boa...

  • Page 65

    3-11 o peration 3 overheating and serious damage could occur. See overheat warning system, page 2-13, for more informa- tion. Bimini top (sx210 model) raising from the fully collapsed storage position. 1) raise the top and secure the rear support poles to the rear support pole mounts with the lock p...

  • Page 66

    3 o peration 3-12 storing in the fully collapsed position 1) follow the steps for storing in the upright position. 2) remove the snap pins holding the rear support poles to the mounting brackets. 3) lower the top onto the rear deck/ hatch. T railering with the bimini top the bimini top must be secur...

  • Page 67

    O peration 3 3-13 bimini top (ar210 model) raising 1) unstrap the top. Unzip and remove the storage cover, then unwrap the top. 2) attach the zippered flaps of the fab- ric of the top to the rearmost tower tube. Tower tube zipper flaps 3) pull the top forward. Unclip the plas- tic clips and pull the...

  • Page 68

    3 o peration 3-14 5) collapse the front support poles until the snap buttons click into place to tighten the top fabric . Collapsed support pole do not exceed 45 mph (72 km/h) with the bimini top in the up position. Storing 1) extend the forward support poles by pressing in the snap buttons. 2) remo...

  • Page 69

    O peration 3 3-15 operation starting the engines severe injury or death may result if you ignore any of the following: • before operating your boat, become familiar with all con- trols. Consult your yamaha dealer about any control or function you do not fully understand. Failure to understand how th...

  • Page 70

    3 o peration 3-16 2) attach the engine shut-off cord to your pfd. Install the cord clip onto the engine shut-off switch by push- ing the clip groove over the nut beneath the knob. Be sure the cord is not wrapped around the steering wheel or tangled in the controls. Engine shut-off switch clip with c...

  • Page 71

    O peration 3 3-17 • never turn the ignition key to “start” while the engine is run- ning. The starter mechanism could be damaged. • if the starter motor is engaged continuously for more than 5 seconds, the battery will become quickly discharged and it will be impossible to start the engine. The star...

  • Page 72

    3 o peration 3-18 break-in procedure the engine break-in period is essential to allow the various components of the engine to wear and polish themselves to the correct operating clearances. This ensures proper performance and promotes longer component life. 1) launch the boat and start the engines (...

  • Page 73

    O peration 3 3-19 driving your boat getting to know your boat operating your boat requires skills acquired through practice over a period of time. Take the time to learn the basic techniques well before attempting more difficult maneuvers. Boating with your new boat can be a very enjoyable activity,...

  • Page 74

    3 o peration 3-20 turning the boat • do not pull the throttle levers back to idle when trying to steer away from objects – you need throttle to steer. • be sure passengers are hold - ing on before making turns. An unprepared passenger could lose balance and fall. Steering control depends on the com-...

  • Page 75

    O peration 3 3-21 turning left turning right boating with passengers when passengers are on board, make sure they are seated and hold- ing on before you start to acceler- ate. An unprepared passenger could lose balance and fall. Your boat is designed for one operator and up to eight passengers only....

  • Page 76

    3 o peration 3-22 1) be sure engines are off, then move to the stern of the boat. Pull out the ladder and climb up onto the step. Return the ladder to the stowed position before climbing into the boat. 2) climb up onto the swim platform, then sit in one of the seats provided. Boarding from a dock or...

  • Page 77

    O peration 3 3-23 stopping • you will lose steering control if you completely pull the throttles back to idle. You need throttle to steer. • do not use the reverse function to slow down or stop the boat from planing speed as it could cause you to lose control, be ejected, or impact the steering whee...

  • Page 78

    3 o peration 3-24 wind or current pushing boat toward dock: slowly maneuver to a shallow angle and allow the boat to move toward the dock. No wind or current: approach the dock at a shallow angle. Secure the bow to the dock, then use engine thrust or a boat hook to gently move the stern to the dock....

  • Page 79

    O peration 3 3-25 anchoring always anchor from the bow. Anchoring from the stern will make the boat unsteady. A strong cur- rent can pull a stern-anchored boat underwater. Select an anchor appropriate for your boat and water conditions. A “danforth” (or fluke) type anchor is suitable for most applic...

  • Page 80

    3 o peration 3-26 crossing wakes and swells you will not always have flat, smooth water. There will be swells and wakes from other boats, etc. The best way to cross wakes and swells is with the least jolt to you and the boat. Small swells are not as dif- ficult to cross as larger swells or wakes. Cr...

  • Page 81

    O peration 3 3-27 post-operation checks post-operation checks these post-operation procedures are developed to help preserve the long- term appearance and reliability of your boat. Perform these procedures as soon as possible after the boat is loaded back on the trailer after the day’s use. Some own...

  • Page 82

    3 o peration 3-28 5) remove hull drain plug and the engine compartment drain plug . Rinse the engine compartment with a small amount of fresh water. Be careful not to get water on the carbu- retor or electrical components. Allow any water in the bilge to drain out. After the water has drained, wipe ...

  • Page 83

    O peration 3 3-29 trailering avoid accident and injury from improper trailering: • the trailer must be matched for the boat’s weight and hull. • the towing vehicle must have the capacity of pulling the load. Pulling a load that exceeds the towing capacity may cause loss of control. • be sure the boa...

  • Page 84

    3 o peration 3-30 • check wheel bearings and wheel lug nuts before each trip. • check tail, brake, and turn signal lights for proper operation. • secure the bow of the boat to the trailer with the winch line and also with the chain. Secure the stern cleats to the trailer with tie-downs. • take down ...

  • Page 85

    O peration 3 3-31 backing your trailer it takes practice to back a trailer suc- cessfully. If you are not familiar backing up with a trailer, practice first in an open area away from obstacles. Keep the following points in mind: • back slowly. Make steering adjust- ments in small steps. • turn the t...

  • Page 86

    3 o peration 3-32 loading 1) back the trailer down the ramp as close to 90° to the shoreline as you can. If possible, have a second person act as an observer while standing to the side of the boat. Stop when the tops of the trailer’s fenders are about 3 inches above the water- line. 2) with the boat...

  • Page 87

    O peration 3 3-33 • attach guidelines to the bow eye and stern tie-down cleats to control movement of the boat during lifting. • remove all people and all cargo from the boat. Drain any excess water from the bilge using the bilge pump. • be sure all people are standing clear, then lift boat slowly a...

  • Page 89

    Chapter 4 maintenance and care storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 cooling system flushing . . . . . . . . . . . . ....

  • Page 91

    4-1 m aintenance & c are 4 storage storing your boat for prolonged peri- ods of time, such as winter storage, requires preventative maintenance to ensure against deterioration. It is advis- able to have the boat serviced by an authorized yamaha boat dealer before storage. However, the following proc...

  • Page 92

    4-2 4 m aintenance & c are 4) turn off the water supply, then drain residual water from the exhaust sys- tem by alternately pushing the throt- tle lever up to half throttle and back for 10 to 15 seconds. Shut off engine. Never have the water on when the engine is not running. The water could flow ba...

  • Page 93

    4-3 m aintenance & c are 4 battery 1) when the boat is not to be used for a month or more, remove the battery and store it in a cool, dark place. Clean the battery’s casing and ter- minals using yamalube ® battery cleaner and protector or a mixture of baking soda and water (one tbsp. Of baking soda ...

  • Page 94

    4-4 4 m aintenance & c are 2) remove the drain plugs in the stern and engine compartment . Clean the hull, boat interior, and drive units with yamaclean wash & wax concentrate or a mild nat- ural soap and water. Rinse with fresh water. Scum on the hull can be removed with yamaclean hull cleaner. Not...

  • Page 95

    4-5 m aintenance & c are 4 basic stain guide here are basic steps to remove common stains from boat upholstery. Consult your dealer or upholstery-cleaning professional for difficult stains. Type of stain steps (rinse with clean, warm water and then dry after application) 1 2 3 general care/ dirt a b...

  • Page 96

    4-6 4 m aintenance & c are maintenance and adjustment be sure to turn off the engines when you perform maintenance unless otherwise specified. If you are not familiar with machine servicing, this work should be done by a yamaha dealer or other qualified mechanic. Maintenance, replacement, or repair ...

  • Page 97

    4-7 m aintenance & c are 4 maintenance interval initial thereafter every page 10 hours 50 hours 100 hours 100 hours 200 hours 6 months 12 months 12 months 24 months spark plug inspection/cleaning/ adjustment grease points greasing 4-8 bearing housing greasing *1 *2 *2 4-9 fuel system inspection 4-10...

  • Page 98

    4-8 4 m aintenance & c are grease points to keep moving parts sliding or rotating smoothly, coat them with water resis- tant grease such as yamaha marine grease, yamaha grease a, or an equiv- alent. Steering cable ball joints and inner wire grease the steering cable and shift cables ball joints at t...

  • Page 99

    4-9 m aintenance & c are 4 bearing housing bearing housing grease nipple grease the bearing housing through the grease nipple. The first service should be done after 10 hours or 1 month by your yamaha dealer. Fill the bearing housing with water- resistant grease through the grease nipple. After firs...

  • Page 100

    4-10 4 m aintenance & c are fuel system inspection gasoline is highly flammable and explosive. Failure to check for and repair any fuel leakage could result in fire or explosion. A fire or explo- sion can cause severe injury or death. When inspecting the fuel system, shut off the engine, do not smok...

  • Page 101

    4-11 m aintenance & c are 4 fuel system cleaning if the fuel system needs to be cleaned or when any water is found in the fuel system, take the boat to your yamaha dealer for service. Engine oil/filter engine oil is extremely hot after the engine is turned off. Coming into contact with or getting an...

  • Page 102

    4-12 4 m aintenance & c are air filter the air filter element should be checked every 12 months or every 100 hours of operation. To check the air filter: 1) open the hood (see page 2-17). 2) lift the locking tab on the air filter case. Turn the air filter case cap counterclockwise and then remove th...

  • Page 103

    4-13 m aintenance & c are 4 controls (throttle/shift) check the control levers for smooth operation and proper shifting. 1) remove the engine stop switch cord (lanyard) and ignition keys. 2) push and pull the control levers through their full range, from neutral to wide-open throttle forward and fro...

  • Page 104

    4-14 sacrificial anodes an aluminum alloy anode is mounted on each jet pump outlet on your boat. Galvanic corrosion can damage metal surfaces below the waterline on any boat, particularly in saltwater. These “sacrificial” anodes are designed to erode in these conditions first, before metal component...

  • Page 105

    4-15 m aintenance & c are 4 fuse replacement the fuse is in the electrical box. To replace the fuse, unscrew the cap and pull the two red leads out with the fuse holder. Open the fuse holder and replace the fuse. Electrical box fuse (10a) cap fuse holder accessory fuse fuse (20a) the fuse is on the ...

  • Page 106

    4-16 battery electrolyte is poisonous and dangerous, causing severe burns, etc. It contains sulfuric acid. Avoid contact with skin, eyes or clothing. Antidote: external – flush with water. Internal – drink large quantities of water or milk. Follow with milk of magnesia, beaten egg or vegetable oil. ...

  • Page 107

    4-17 m aintenance & c are 4 positive (+) battery cable (red) negative ( –) battery cable (black) accessory (+) lead (red/black) accessory (–) lead (black) battery removal: disconnect battery leads before removing the battery. Disconnect the negative (–) lead first. Battery installation: connect the ...

  • Page 108

    # s afety i nformation 4-18 4 m aintenance & c are model xx item unit sx210: lat1100b-l vehicle capacity maximum people on board number of people 9 maximum load capacity (persons) lb. 1670 dimensions length feet / inches 21' / 255.9" beam feet / inches 8.6' /102.4" draft inches 15" dry weight lb. 28...

  • Page 109

    M aintenance & c are 4 4-19 model xx item unit ar210: lat1100a-l vehicle capacity maximum people on board number of people 9 maximum load capacity (persons) lb. 1670 dimensions length feet / inches 21' / 255.9" beam feet / inches 8.6' /102.4" draft inches 15" dry weight lb. 2875 height on trailer fe...

  • Page 111

    Chapter 5 trouble recovery troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 troubleshooting chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 emergency procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 113

    5-1 t rouble r ecovery 5 troubleshooting if any trouble happens on your boat, use this section to check for possible cause. If you cannot find the cause or if the procedure for replacement or repair is not described in this owner’s manual, ask your yamaha boat dealer or qualified mechanic for the pr...

  • Page 114

    5-2 5 t rouble r ecovery trouble possible cause remedy page engine runs irregularly or stalls • fuel empty • refill as soon as possible 3-1 stale or contaminated • have serviced at yamaha dealer • fuel filter water or dust collected • have serviced at yamaha dealer • spark plug fouled or defective •...

  • Page 115

    5-3 t rouble r ecovery 5 emergency procedures towing the boat bow eye the boat should be towed only if it becomes inoperative. The towing rope should be long enough so that the boat will not collide with the towing boat when slowing down. A good rule of thumb is a tow rope which is three times the c...

  • Page 116

    5-4 jump starting severe injury or death may result if you ignore any of the following: • if blower will not operate, ventilate engine compartment by opening engine compartment hatch for several minutes before attempt- ing a jump start. • do not connect the negative (–) jumper cable to the negative ...

  • Page 117

    5-5 t rouble r ecovery 5 jet pump clean-out procedure severe injury or death may result if you ignore any of the following: • turn off and remove both ignition keys, remove lanyard, and wait for all movement to stop before removing access port caps. • never override interlocks to run engine with hat...

  • Page 118

    5-6 5 t rouble r ecovery 6) press the t-handle down firmly to lock the cap in place. Pull up force- fully on the handle to be sure it is locked. If a strong pull will move the handle, it is not locked securely – the cap could be forced out by water pressure during operation. • be sure the caps are l...

  • Page 119

    Chapter 6 consumer information & index limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 yamaha extended service (y.E.S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 boating terms . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 121

    6-1 c onsumer i nformation & i ndex 6 yamaha motor corporation, u.S.A. Yamaha boat limited warranty yamaha motor corporation, u.S.A. Hereby warrants that new yamaha boats will be free from defects in materials or workmanship for the period of time stated herein, subject to certain stated limitations...

  • Page 122

    6-2 6 c onsumer i nformation & i ndex specific parts excluded from warranty; parts replaced due to normal wear or routine maintenance such as oil, spark plugs, fuel filters, impeller and liner, and anodes are not covered by warranty. Charges for transporting the boat to and from an authorized yamaha...

  • Page 123

    6-3 c onsumer i nformation & i ndex 6 q. May i perform any or all of the recommended maintenance shown in the owner’s manual instead of having the dealer do them? A. Yes, if you are a qualified mechanic and follow the procedures specified in the owner’s and service manual. We do recommend, however, ...

  • Page 124

    6-4 6 c onsumer i nformation & i ndex keep your yamaha boat protected even after the 1-year warranty coverage provisions expire with genuine yamaha extended service (y.E.S.). Y.E.S. Is designed and administered by yamaha motor corporation to provide maxi- mum owner satisfaction. You get uninterrupte...

  • Page 125

    6-5 c onsumer i nformation & i ndex 6 boating terms term definition bow the front part of the boat. Deck the “floor” or upper structure which covers the hull. Give-way the vessel which must yield the right-of-way when two boats meet. Gunwale the meeting junction of the deck and hull; the upper edge ...

  • Page 126

    6-6 sample float plan 6 c onsumer i nformation & i ndex leave a float plan with a responsible person on shore before boating. The example below can be copied and used. Float plan vessel information boat make: yamaha motor type: jet model: length: registration no: deck color: hull color: passenger op...

  • Page 127

    6-7 c onsumer i nformation & i ndex 6 a access port caps. . . . . . . . . . . . . 3-7, 5-5 adjustment and maintenance. . . . . . . 4-6 age limit. . . . . . . . . . . . . . . . . . . . . . . 1-7 air filter . . . . . . . . . . . . . . . . . . . . . . 4-12 anchor . . . . . . . . . . . . . . . . . . . ....

  • Page 128

    6-8 6 c onsumer i nformation & i ndex d deck drain . . . . . . . . . . . . . . . . . . . . . 3-7 deep alarm. . . . . . . . . . . . . . . . . . . . . 2-12 depth finder . . . . . . . . . . . . . . . . . . . . 2-10 docking. . . . . . . . . . . . . . . . . . . . . . . 3-23 drain plugs . . . . . . . . . ...

  • Page 129

    6-9 c onsumer i nformation & i ndex 6 lanyard (engine shut-off cord) . . . . . . 1-11, 2-6, 3-10, 3-15, 5-1 launching. . . . . . . . . . . . . . . . . . . . . 3-31 lights . . . . . . . . . 1-8, 1-12, 2-2, 2-14, 3-9 limit on running engine out of water . . 4-2 limit on starter motor running period . ...

  • Page 130

    6-10 steering inspection. . . . . . . . . . . 3-5, 4-12 steering pivot points, greasing . . . . . . 4-8 steering wheel tilt adjustment. . . . . . . . . . . . . . . . . 2-5 stern light . . . . . . . . . . 1-12, 2-2, 2-14, 3-9 stopping . . . . . . . . . . . . . . . . . . . . . . 3-23 stopping the engi...

  • Page 131: Ar/sx 210

    Lit-18626-09-42 ©2011 yamaha motor corporation, u.S.A. Printed in u.S.A. Ar/sx 210 owne r ’s /o p e r at o r’s m a nu a l warning read this manual carefully before operating this boat. Ar/sx 210 owner’s/operator’s manual.