Summary of CRW4001t
Page 1
Crw4001t series user guide guide de i’utilisateur bedienungsanleitung.
Page 2
Fcc information (u.S.A.) 1. Important notice: do not modify this unit! This product, when installed as indicated in the instructions contained in this manual, meets fcc requirements. Modifications not expressly approved by yamaha may void your authority, granted by the fcc, to use the product. 2. Im...
Page 3
T his output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. Ansi class : class 1 material : gaalas wavelength : 780-790 nm emission duration : continuous laser output power : less than 44.6 µ w* * laser diode properties caution use of controls or ...
Page 4: Warning
Warning i ❢ warning ❢ • the temperature where crw4001t is located should be between 5ºc and 40ºc (41ºf – 104ºf), when used in a fan-cooled system. • do not disassemble the crw4001t cover to reduce the risk of electric shock. • always remove the disc before transporting crw4001t..
Page 5: Important Precautions
Important precautions ii important precautions please read the following precautions before attempt- ing to operate the crw4001t. • before recording a disc, be sure to clean the disc and tray using an air aerosol-type dust remover. A dust particle on the disc may cause recording to fail, producing a...
Page 6: Table of Contents
Table of contents iii table of contents introduction ............................................................................. 1 crw4001t features ...................................................... 1 orange book compatible recording ............................ 2 chapter 1 - system configura...
Page 7: Introduction
Introduction 1 introduction thank you for purchasing a yamaha crw4001t drive. Please read this manual before using the drive in order to make the best use of the supe- rior crw4001t functions. After reading, please retain this manual for future reference. Crw4001t features ■ 2xs recording (rewritabl...
Page 8: Introduction
Introduction 2 orange book compatible recording track at once in this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in cd players or cd-rom drives other than a cd-rw or cd-r drive until the session is closed. Multisession in this mode, data can ...
Page 9: Computer
Chapter 1 - system configuration 3 chapter 1 - system configuration before using the crw4001t, make sure that you have all of the items on the list of included items. In order to use the crw4001t, you will require the following. Computer the following operating environment is required: • an ibm/at c...
Page 10: Discs
Chapter 1 - system configuration 4 discs on the crw4001t, you can use conventional cd-rw and cd-r discs that conform to the recordable compact disc systems part 2 and part 3 (orange book). Yamaha recommends the following yamaha cd-rw and cd-r discs: cd-rw discs > crwm74r ( φ 120mm, 74 minutes) cd-r ...
Page 11: Master/slave Settings
Chapter 2 - installing the yamaha crw4001t drive 5 chapter 2 - installing the yamaha crw4001t drive master/slave settings before you install the crw4001t in your computer, you must make the master/slave setting. This setting is set by inserting a jumper pin in the jumper switch located on the rear p...
Page 12
Chapter 2 - installing the yamaha crw4001t drive 6 ♦ setting the crw4001t as the master ♦ setting the crw4001t as the slave ♦ csel (cable select) if you use the csel setting, the master/slave setting will be made automatically depending on the hardware configuration. For details refer to the manual ...
Page 13: Off
Chapter 2 - installing the yamaha crw4001t drive 7 installing the crw4001t drive the following steps will differ slightly depending on the type of computer you are using. For details on removing the cover from your computer, and installing or removing internal devices, refer to the manual for your c...
Page 14
Chapter 2 - installing the yamaha crw4001t drive 8 4. Remove the front cover of a vacant half-height drive bay. For details refer to the manual of your computer. 5. Slide the crw4001t drive into the drive bay from the front. At this time, be careful not to apply excessive force to the drive itself. ...
Page 15
Chapter 2 - installing the yamaha crw4001t drive 9 7. Connect the audio cable. Connect the single 4-pin connector (sound blaster compatible) to the sound card. Connect the 4-pin connector at the other end of the cable (the larger connector) to the audio out connector on the crw4001t drive. The polar...
Page 16
Chapter 2 - installing the yamaha crw4001t drive 10 8. Connect the power supply cable. Connect the +12v and +5v 4-pin power cable to the power supply inter- face located on the rear panel of the crw4001t drive. The shape of the connector makes it impossible to reverse the connections. Dc input i/f 9...
Page 17
Chapter 2 - installing the yamaha crw4001t drive 11 10. Attach the cover of your computer. 11. Connect the power cable to an ac outlet, and switch on your computer. Make sure that the led located on the panel of the crw4001t drive is lit. 12. Start up your operating system. For the procedure, refer ...
Page 18: Chapter 3 - Operation
Chapter 3 - operation 12 chapter 3 - operation front panel 1 disc tray the disc is inserted and ejected here. Pressing the eject button will open the tray. 2 headphone jack this stereo mini jack allows you to connect headphones and listen to audio. 3 headphone volume control this control adjusts the...
Page 19: Chapter 3 - Operation
Chapter 3 - operation 13 loading a disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the disc tray softly or press the eject button again to close the disc tray. On/ disc vol read/ write recordable.
Page 20: Chapter 3 - Operation
Chapter 3 - operation 14 ejecting the disc if the crw4001t is powered on: press the eject button to eject the disc. Note: you cannot eject the disc if the atapi command prohibits the eject opera- tion while the crw4001t is reading data. Caution: be sure to remove the disc after it is completely ejec...
Page 21: Troubleshooting
Troubleshooting 15 troubleshooting if crw4001t is not performing as expected, look up the symptoms in the following table, and take the appropriate corrective action. Symptoms corrective action the power to the crw4001t is off • check the dc power cable connection. The crw4001t is not recognized by ...
Page 22: Appendix
Appendix 16 specifications specifications are subject to change without prior notice. Interface atapi/ide data capacity 1.2m/sec: 666mb 1.4m/sec: 540mb record/read speed writing (cd-rw): 2x speed writing (cd-r): normal speed, 2x speed, 4xspeed reading: normal speed, 2x speed, 4x speed, 6x speed data...
Page 23: Appendix
Appendix 17 front panel indicator key ● on: green ✦ flashing: green — off ❍ on: orange ✧ flashing: orange status on/disc read/write reset ❍ ➠ — ❍ ➠ — ready (no disc) ❍ — inserting disc ✧ ➠ ✦ — ejecting disc ✧ — ready (disc inserted) ● — seeking ● ✦ preparing to write ● ✧ writing ● ❍ writing (test mo...
Page 24: Japan
Yamaha corporation electronic systems division printed in japan vz24450-1 english: if you have any questions, please contact your dealer or one of the following companies. French: pour plus de détails sur les produits, veuillez vous adresser à yamaha ou au distributeur le plus proche figurant dans l...