1. DL manuals
  2. Yamaha
  3. Scooter
  4. CRYPTON T110C
  5. Owner's Manual

Yamaha CRYPTON T110C Owner's Manual

Other manuals for CRYPTON T110C: Owner's Manual

Summary of CRYPTON T110C

  • Page 1

    Dic183 t110c owner’s manual read this manual carefully before operating this vehicle. 40b-f8199-e2 [english (e)].

  • Page 2

    Eau46090 read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold. U40be2e0.Book page 1 wednesday, october 10, 2012 8:01 am.

  • Page 3

    Introduction eau10102 welcome to the yamaha world of motorcycling! As the owner of the t110c, you are benefiting from yamaha’s vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned yamaha a reputation for dependability. Please take the...

  • Page 4

    Important manual information eau10133 particularly important information is distinguished in this manual by the following notations: *product and specifications are subject to change without notice. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey a...

  • Page 5

    Important manual information eau37230 t110c owner’s manual ©2012 by yamaha motor co., ltd. 1st edition, september 2012 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor co., ltd. Is expressly prohibited. Printed in china. U40be2e0.Book page 2 wedn...

  • Page 6

    Table of contents safety information ..................1-1 description ..................................2-1 left view ..........................................2-1 right view ........................................2-2 controls and instruments.................2-3 instrument and control functions .....

  • Page 7

    Table of contents checking the steering ...................6-26 checking the wheel bearings .......6-26 battery ..........................................6-26 replacing the fuse ........................6-28 replacing the headlight bulb ........6-28 replacing the tail/brake light bulb ..................

  • Page 8

    1-1 1 safety information eau1028a be a responsible owner as the vehicle’s owner, you are respon- sible for the safe and proper operation of your motorcycle. Motorcycles are single-track vehicles. Their safe use and operation are de- pendent upon the use of proper riding techniques as well as the exp...

  • Page 9

    Safety information 1-2 1 ● many accidents involve inexperi- enced operators. In fact, many op- erators who have been involved in accidents do not even have a cur- rent motorcycle license. • make sure that you are qualified and that you only lend your mo- torcycle to other qualified opera- tors. • kn...

  • Page 10

    Safety information 1-3 1 avoid carbon monoxide poisoning all engine exhaust contains carbon monoxide, a deadly gas. Breathing car- bon monoxide can cause headaches, dizziness, drowsiness, nausea, confu- sion, and eventually death. Carbon monoxide is a colorless, odor- less, tasteless gas which may b...

  • Page 11

    Safety information 1-4 1 tents, can create unstable han- dling or a slow steering re- sponse. ● this vehicle is not designed to pull a trailer or to be attached to a sidecar. Genuine yamaha accessories choosing accessories for your vehicle is an important decision. Genuine yamaha accessories, which ...

  • Page 12

    Safety information 1-5 1 tor and may limit control ability, therefore, such accessories are not recommended. ● use caution when adding electri- cal accessories. If electrical acces- sories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause ...

  • Page 13

    Description 2-1 2 eau10410 left view 1,2 3 4 5 6 8 7 1. Battery (page 6-26) 2. Fuse (page 6-28) 3. Storage compartment (page 3-9) 4. Owner’s tool kit (page 6-2) 5. Fuel tank cap (page 3-5) 6. Seat lock (page 3-8) 7. Engine oil drain bolt (page 6-9) 8. Shift pedal (page 3-4) u40be2e0.Book page 1 wedn...

  • Page 14

    Description 2-2 2 eau10420 right view 1 2 3 4 7 6 5 1. Carrier (page 3-10) 2. Helmet holder (page 3-8) 3. Kickstarter (page 3-8) 4. Front brake fluid reservoir (page 6-19) 5. Air filter element (page 6-11) 6. Brake pedal (page 3-5) 7. Engine oil filler cap (page 6-9) u40be2e0.Book page 2 wednesday, ...

  • Page 15

    Description 2-3 2 eau10430 controls and instruments 1 2 3 5 6 7 4 1. Left handlebar switches (page 3-3) 2. Speedometer unit (page 3-3) 3. Fuel gauge (page 3-3) 4. Main switch/steering lock (page 3-1) 5. Right handlebar switch (page 3-3) 6. Brake lever (page 3-4) 7. Throttle grip (page 6-13) u40be2e0...

  • Page 16

    Instrument and control functions 3-1 3 eau10461 main switch/steering lock the main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. Eau47821 (on) all electrical circuits are supplied with power, the meter li...

  • Page 17

    Instrument and control functions 3-2 3 to unlock the steering insert the key and turn it to “ ”. Eau10981 indicator lights eau11020 turn signal indicator light “ ” this indicator light flashes when the turn signal switch is pushed to the left or right. Eau11060 neutral indicator light “ ” this indic...

  • Page 18

    Instrument and control functions 3-3 3 eaut1821 speedometer unit the speedometer unit is equipped with a speedometer and an odometer. The speedometer shows the riding speed. The odometer shows the total distance traveled. Eau47830 fuel gauge the fuel gauge indicates the amount of fuel in the fuel ta...

  • Page 19

    Instrument and control functions 3-4 3 eau12400 dimmer switch “ / ” set this switch to “ ” for the high beam and to “ ” for the low beam. Eau12460 turn signal switch “ / ” to signal a right-hand turn, push this switch to “ ”. To signal a left-hand turn, push this switch to “ ”. When re- leased, the ...

  • Page 20

    Instrument and control functions 3-5 3 eau12941 brake pedal the brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the brake pedal. Eau37471 fuel tank cap to remove the fuel tank cap 1. Open the seat. (see page 3-8.) 2. Turn the fuel tank cap counter- clockwis...

  • Page 21

    Instrument and control functions 3-6 3 eau13212 fuel make sure there is sufficient gasoline in the tank. Warning ewa10881 gasoline and gasoline vapors are extremely flammable. To avoid fires and explosions and to reduce the risk of injury when refueling, follow these instructions. 1. Before refuelin...

  • Page 22

    Instrument and control functions 3-7 3 eau13445 catalytic converters this vehicle is equipped with catalytic converters in the exhaust system. Warning ewa10862 the exhaust system is hot after op- eration. To prevent a fire hazard or burns: ● do not park the vehicle near possible fire hazards such as...

  • Page 23

    Instrument and control functions 3-8 3 eau47860 kickstarter if the engine fails to start by pushing the start switch, try to start it by using the kickstarter. With the transmission in neutral, fold out the kickstarter lever, move it down lightly with your foot until the gears engage, and then push ...

  • Page 24

    Instrument and control functions 3-9 3 to release a helmet from a helmet holder open the seat, remove the helmet from the helmet holder, and then close the seat. Eau14453 storage compartment the storage compartment is located under the seat. (see page 3-8.) when storing the owner’s manual or other d...

  • Page 25

    Instrument and control functions 3-10 3 eau15112 carrier warning ewa10171 ● do not exceed the load limit of 3.0 kg (6.6 lb) for the carrier. ● do not exceed the maximum load of 167 kg (368 lb) for the ve- hicle. Eau55180 sidestand (for sidestand- equipped models) the sidestand is located on the left...

  • Page 26

    For your safety – pre-operation checks 4-1 4 eau15597 inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the owner’s manual. Warning ewa11151 failure to inspect or maint...

  • Page 27

    For your safety – pre-operation checks 4-2 4 control cables • make sure that operation is smooth. • lubricate if necessary. 6-23 drive chain • check chain slack. • adjust if necessary. • check chain condition. • lubricate if necessary. 6-20, 6-22 wheels and tires • check for damage. • check tire con...

  • Page 28

    Operation and important riding points 5-1 5 eau15951 read the owner’s manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your yamaha dealer. Warning ewa10271 failure to familiarize yourself with the controls can lead to loss of con- tr...

  • Page 29

    Operation and important riding points 5-2 5 eau16640 starting a warm engine follow the same procedure as for start- ing a cold engine with the exception that the starter (choke) is not required when the engine is warm. Eau47840 shifting shifting gears lets you control the amount of engine power avai...

  • Page 30

    Operation and important riding points 5-3 5 eau16800 tips for reducing fuel con- sumption fuel consumption depends largely on your riding style. Consider the following tips to reduce fuel consumption: ● turn the starter (choke) off as soon as possible. ● shift up swiftly, and avoid high en- gine spe...

  • Page 31

    Operation and important riding points 5-4 5 eau17213 parking when parking, stop the engine, and then remove the key from the main switch. Warning ewa10311 ● since the engine and exhaust system can become very hot, park in a place where pedestri- ans or children are not likely to touch them and be bu...

  • Page 32

    Periodic maintenance and adjustment 6-1 6 eau17244 periodic inspection, adjustment, and lu- brication will keep your vehicle in the safest and most efficient condition pos- sible. Safety is an obligation of the vehi- cle owner/operator. The most important points of vehicle inspection, adjust- ment, ...

  • Page 33

    Periodic maintenance and adjustment 6-2 6 eau39691 owner’s tool kit the owner’s tool kit is located on the bottom of the seat. (see page 3-8.) the service information included in this manual and the tools provided in the owner’s tool kit are intended to assist you in the performance of preventive ma...

  • Page 34

    Periodic maintenance and adjustment 6-3 6 eau46871 tip ● the annual checks must be performed every year, except if a kilometer-based maintenance, or for the uk, a mileage-based maintenance, is performed instead. ● from 30000 km (17500 mi), repeat the maintenance intervals starting from 6000 km (3500...

  • Page 35

    Periodic maintenance and adjustment 6-4 6 eau17718 general maintenance and lubrication chart no. Item check or maintenance job odometer reading annual check 1000 km (600 mi) 6000 km (3500 mi) 12000 km (7000 mi) 18000 km (10500 mi) 24000 km (14000 mi) 1 air filter element • clean. √ √ • replace. √ √ ...

  • Page 36

    Periodic maintenance and adjustment 6-5 6 9 * swingarm • check operation and for exces- sive play. √ √ √ √ • lubricate with lithium-soap-based grease. Every 24000 km (14000 mi) 10 drive chain • check chain slack, alignment and condition. • adjust and thoroughly lubricate chain with engine oil. Every...

  • Page 37

    Periodic maintenance and adjustment 6-6 6 eau18660 tip ● the air filter needs more frequent service if you are riding in unusually wet or dusty areas. ● hydraulic brake service • regularly check and, if necessary, correct the brake fluid level. • every two years replace the internal components of th...

  • Page 38

    Periodic maintenance and adjustment 6-7 6 eau18741 removing and installing the cowling and panel the cowling and panel shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time the cowling or panel needs to be re- moved and installed....

  • Page 39

    Periodic maintenance and adjustment 6-8 6 to install the panel 1. Insert the projection into the slot, and then slide the panel forward. 2. Place the panel in its original posi- tion, and then install the screw. Eau19604 checking the spark plug the spark plug is an important engine component, which ...

  • Page 40

    Periodic maintenance and adjustment 6-9 6 2. Check the spark plug for electrode erosion and excessive carbon or other deposits, and replace it if necessary. 3. Measure the spark plug gap with a wire thickness gauge and, if nec- essary, adjust the gap to specifica- tion. To install the spark plug 1. ...

  • Page 41

    Periodic maintenance and adjustment 6-10 6 tip the engine oil should be between the minimum and maximum level marks. 4. If the engine oil is at or below the minimum level mark, add sufficient oil of the recommended type to raise it to the correct level. 5. Insert the dipstick into the oil filler hol...

  • Page 42

    Periodic maintenance and adjustment 6-11 6 addition, do not use oils labeled “energy conserving ii” or higher. ● make sure that no foreign mate- rial enters the crankcase. 6. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, im- mediatel...

  • Page 43

    Periodic maintenance and adjustment 6-12 6 4. Insert the air filter element into the air filter case. Notice: make sure that the air filter element is prop- erly seated in the air filter case. The engine should never be op- erated without the air filter ele- ment installed, otherwise the piston(s) a...

  • Page 44

    Periodic maintenance and adjustment 6-13 6 tip if the specified idling speed cannot be obtained as described above, have a yamaha dealer make the adjustment. Eau21384 checking the throttle grip free play the throttle grip free play should mea- sure 3.0–7.0 mm (0.12–0.28 in) at the inner edge of the ...

  • Page 45

    Periodic maintenance and adjustment 6-14 6 eau21576 tires tires are the only contact between the vehicle and the road. Safety in all con- ditions of riding depends on a relatively small area of road contact. Therefore, it is essential to maintain the tires in good condition at all times and replace ...

  • Page 46

    Periodic maintenance and adjustment 6-15 6 tire information this motorcycle is equipped with tube tires. Tires age, even if they have not been used or have only been used occasion- ally. Cracking of the tread and sidewall rubber, sometimes accompanied by carcass deformation, is an evidence of ageing...

  • Page 47

    Periodic maintenance and adjustment 6-16 6 eau22003 cast wheels warning ewa10610 the wheels on this model are not de- signed for use with tubeless tires. Do not attempt to use tubeless tires on this model. To maximize the performance, durabil- ity, and safe operation of your vehicle, note the follow...

  • Page 48

    Periodic maintenance and adjustment 6-17 6 eau39813 adjusting the brake pedal free play the brake pedal free play should mea- sure 20.0–30.0 mm (0.79–1.18 in) at the brake pedal end as shown. Period- ically check the brake pedal free play and, if necessary, adjust it as follows. To increase the brak...

  • Page 49

    Periodic maintenance and adjustment 6-18 6 eau22294 brake light switches the brake light, which is activated by the brake pedal and brake lever, should come on just before braking takes ef- fect. If necessary, adjust the rear brake light switch as follows, but the front brake light switch should be ...

  • Page 50

    Periodic maintenance and adjustment 6-19 6 indicator grooves have almost disap- peared, have a yamaha dealer replace the brake pads as a set. Eau22540 rear brake shoes the rear brake is provided with a wear indicator, which allows you to check the brake shoe wear without having to dis- assemble the ...

  • Page 51

    Periodic maintenance and adjustment 6-20 6 as the brake pads wear, it is normal for the brake fluid level to gradually go down. A low brake fluid level may indi- cate worn brake pads and/or brake sys- tem leakage; therefore, be sure to check the brake pads for wear and the brake system for leakage. ...

  • Page 52

    Periodic maintenance and adjustment 6-21 6 5. Install the check hole cap. 6. If the drive chain slack is incorrect, adjust it as follows. Eau55190 to adjust the drive chain slack consult a yamaha dealer before ad- justing the drive chain slack. 1. Place the motorcycle on the cen- terstand. 2. Loosen...

  • Page 53

    Periodic maintenance and adjustment 6-22 6 5. Tighten both locknuts, and then tighten the axle nut and brake torque rod nut to their specified torques. Tip when tightening the axle nut, hold the wheel axle with a wrench to keep it from turning. 6. Adjust the brake pedal free play. (see page 6-17.) w...

  • Page 54

    Periodic maintenance and adjustment 6-23 6 eau23095 checking and lubricating the cables the operation of all control cables and the condition of the cables should be checked before each ride, and the ca- bles and cable ends should be lubricat- ed if necessary. If a cable is damaged or does not move ...

  • Page 55

    Periodic maintenance and adjustment 6-24 6 eau23183 checking and lubricating the brake pedal the operation of the brake pedal should be checked before each ride, and the pedal pivot should be lubricat- ed if necessary. Eau55170 checking and lubricating the centerstand and sidestand (for sidestand-eq...

  • Page 56

    Periodic maintenance and adjustment 6-25 6 eaum1652 lubricating the swingarm piv- ots the swingarm pivots must be lubricat- ed by a yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart. Eau23272 checking the front fork the condition and operation of the front fo...

  • Page 57

    Periodic maintenance and adjustment 6-26 6 eau45511 checking the steering worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as fol- lows at the intervals specified in the pe- riodic maintenance and lubrication chart. 1. Place the vehicle on th...

  • Page 58

    Periodic maintenance and adjustment 6-27 6 ● batteries produce explosive hy- drogen gas. Therefore, keep sparks, flames, cigarettes, etc., away from the battery and pro- vide sufficient ventilation when charging it in an enclosed space. ● keep this and all batter- ies out of the reach of children. N...

  • Page 59

    Periodic maintenance and adjustment 6-28 6 eau47672 replacing the fuse the fuse holder is located under the battery box cover. If the fuse is blown, replace it as fol- lows. 1. Turn the key to “ ” and turn off all electrical circuits. 2. Open the seat. (see page 3-8.) 3. Remove the battery box cover...

  • Page 60

    Periodic maintenance and adjustment 6-29 6 1. Remove cowling a. (see page 6-7.) 2. Remove the headlight bulb cover. 3. Remove the headlight bulb holder (together with the bulb) by turning it counterclockwise. 4. Remove the burnt-out bulb by pushing it in and turning it counter- clockwise. 5. Place a...

  • Page 61

    Periodic maintenance and adjustment 6-30 6 3. Remove the burnt-out bulb by pushing it in and turning it counter- clockwise. 4. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 5. Place the inner lens in the original position, and then install the outer lens...

  • Page 62

    Periodic maintenance and adjustment 6-31 6 eaus1611 replacing a rear turn signal light bulb 1. Remove the turn signal light lens by removing the screw. 2. Remove the burnt-out bulb by pushing it in and turning it counter- clockwise. 3. Insert a new bulb into the socket, push it in, and then turn it ...

  • Page 63

    Periodic maintenance and adjustment 6-32 6 3. Insert a new bulb into the socket. 4. Install the license plate light cover by installing the screw. Eauw0343 replacing an auxiliary light bulb this model is equipped with two auxil- iary lights. If an auxiliary light bulb burns out, replace it as follow...

  • Page 64

    Periodic maintenance and adjustment 6-33 6 eau24360 front wheel eau55220 to remove the front wheel warning ewa10821 to avoid injury, securely support the vehicle so there is no danger of it falling over. 1. Place the motorcycle on the cen- terstand. 2. Remove the rubber cap, and then loosen the whee...

  • Page 65

    Periodic maintenance and adjustment 6-34 6 2. Lift the wheel up between the fork legs. Tip make sure that there is enough space between the brake pads before insert- ing the brake disc and that the retainer in the speedometer gear unit fits over the slot on the fork leg. 3. Insert the wheel axle, an...

  • Page 66

    Periodic maintenance and adjustment 6-35 6 eau25080 rear wheel eau55240 to remove the rear wheel warning ewa10821 to avoid injury, securely support the vehicle so there is no danger of it falling over. 1. Place the motorcycle on the cen- terstand. 2. Loosen the wheel axle nut. 3. Remove the drive ch...

  • Page 67

    Periodic maintenance and adjustment 6-36 6 7. Remove the axle nut and the washer, and then pull the wheel axle out. 8. Push the wheel forward, and then remove the drive chain from the rear sprocket. Tip the drive chain does not need to be disassembled in order to remove and install the wheel. 9. Rem...

  • Page 68

    Periodic maintenance and adjustment 6-37 6 eau25851 troubleshooting although yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur dur- ing operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and lo...

  • Page 69

    Periodic maintenance and adjustment 6-38 6 eau25904 troubleshooting chart check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There is no fuel. Check the battery. Supply fuel. The engine does not start. Check the battery. The engine does not start. Have a yamaha dealer check the veh...

  • Page 70

    Motorcycle care and storage 7-1 7 eau37833 matte color caution notice eca15192 some models are equipped with matte colored finished parts. Be sure to consult a yamaha dealer for advice on what products to use be- fore cleaning the vehicle. Using a brush, harsh chemical products or cleaning compounds...

  • Page 71

    Motorcycle care and storage 7-2 7 off any detergent residue using plenty of water, as it is harmful to plastic parts. ● do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products, solvent or t...

  • Page 72

    Motorcycle care and storage 7-3 7 4. To prevent corrosion, it is recom- mended to apply a corrosion pro- tection spray on all metal, including chrome- and nickel-plat- ed, surfaces. 5. Use spray oil as a universal clean- er to remove any remaining dirt. 6. Touch up minor paint damage caused by stone...

  • Page 73

    Motorcycle care and storage 7-4 7 2. For motorcycles equipped with a fuel cock that has an “off” posi- tion: turn the fuel cock lever to “off”. 3. Drain the carburetor float chamber by loosening the drain bolt; this will prevent fuel deposits from building up. Pour the drained fuel into the fuel tan...

  • Page 74

    Specifications 8-1 8 dimensions: overall length: 1870 mm (73.6 in) overall width: 675 mm (26.6 in) overall height: 1040 mm (40.9 in) seat height: 770 mm (30.3 in) wheelbase: 1205 mm (47.4 in) ground clearance: 130 mm (5.12 in) minimum turning radius: 1900 mm (74.8 in) weight: curb weight: 102 kg (22...

  • Page 75

    Specifications 8-2 8 chassis: frame type: backbone caster angle: 27.00 ° trail: 79 mm (3.1 in) front tire: type: with tube size: 70/90-17m/c 38p manufacturer/model: duro/hf314a manufacturer/model: dunlop/d104fm (kor) rear tire: type: with tube size: 80/90-17m/c 50p manufacturer/model: duro/hf314a ma...

  • Page 76

    Specifications 8-3 8 rear turn signal light: 12 v, 10.0 w × 2 auxiliary light: 12 v, 3.0 w × 2 license plate light: 12 v, 5.0 w × 1 meter lighting: 12 v, 1.7 w × 1 neutral indicator light: 12 v, 1.7 w × 1 gear position indicator light: 12 v, 3.0 w × 4 high beam indicator light: 12 v, 1.7 w × 1 turn ...

  • Page 77

    Consumer information 9-1 9 eau26372 identification numbers record the frame serial number and engine serial number in the spaces pro- vided below for assistance when order- ing spare parts from a yamaha dealer or for reference in case the vehicle is stolen. Frame serial number: engine serial number:...

  • Page 78

    Index a air filter element, cleaning..................... 6-11 auxiliary light bulb, replacing ................ 6-32 b battery................................................... 6-26 brake fluid, changing ............................ 6-20 brake fluid level, checking .................... 6-19 brake l...

  • Page 79

    Index turn signal light bulb (rear), replacing............................................. 6-31 turn signal switch ................................... 3-4 v valve clearance .................................... 6-13 w wheel bearings, checking .................... 6-26 wheel (front) ....................

  • Page 80

    A5-yoko_blank.Fm page 1 thursday, december 8, 2011 2:18 pm.

  • Page 81

    A5-yoko_blank.Fm page 1 thursday, december 8, 2011 2:18 pm.

  • Page 82

    Printed in china 2012.10-0.3 × 1 cr (e) dic183.