Cx-1 cx-2 owner’s manual contents safety instructions ..................... 2 features ................................... 3 supplied accessories ................ 3 connections ............................. 4 operations ............................... 7 remote control transmitter ...... 11 specifica...
2 7 wall or ceiling mounting – the unit should be mounted to a wall or ceiling only as recommended by the manufacturer. 8 ventilation – the unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, ...
3 caution: read this before operating your unit 1 to ensure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 install your unit in a cool, dry, clean place – away from windows, heat sources, and too much vibration, dust, moisture or cold. Avoi...
4 connections ● before attempting to make any connections to or from this unit, be sure to first switch off the power to this unit and to any other components to which connections are being made. ● when making connections between this unit and other components, be sure all connections are made corre...
5 cx-2 > * : refer to “about the accessory components on the rear panel” on page 6. Ac outlets remote control l r l l r r l r mc/mm phono power amp gnd tape 1 tape 2 ld in cd tuner pb rec out pb rec out pb rec out pb rec out 200w max. Total switched i20v 60hz i.7a max. Total vcr 1 vcr 2 vcr 1 video ...
6 if your video cassette recorder, ld player, etc. And your monitor are equipped with “s” (high-resolution) video terminals, connect them to this unit’s s video terminals, and connect this unit’s s mon out terminal to the “s” video input of your monitor. Otherwise, connect the composite video termin...
7 operations to play a source 1 set to the “ ∞ ” position. 2 3 select a desired input source. * if you select turntable as an input source (phono position), you should confirm that the phono switch on the rear panel is set to the position corresponding to the type of cartridge being used by the turn...
Notes ● if you want to enjoy another source while recording, select it with the input selector. ● loudness (for cx-2 only), bass, treble, balance, volume controls and pure direct switch settings have no effect on the material being recorded. To record a source to tape (or dub from a tape to another)...
9 rec out selector setting on tape dubbing cx-1 > cx-2 > to dub from tape deck 1 to tape deck 2 or 3 (or both tape deck 2 and 3 at the same time) to dub from tape deck 2 to tape deck 1 or 3 (or both tape deck 1 and 3 at the same time) to dub from tape deck 3 to tape deck 1 or 2 (or both tape deck 1 ...
10 when you listen with headphones when listening with headphones privately, connect the headphones to the phones jack. Sounds from the speakers are cut off. Adjusting the bass and treble controls adjusting the balance control adjust the balance of the output volume to the left and right speakers to...
11 remote control transmitter notes about the remote control transmitter battery installation cx-1 > cx-2 > (australia, u.K. And europe models) cx-2 > (u.S.A., canada and general models) battery replacement if you find that the remote control transmitter must be used closer to the main unit, the bat...
12 cx-1 > cx-2 > (australia, u.K. And europe models) cx-2 > (u.S.A., canada and general models) * when you operate this unit and/or other yamaha components with this remote control transmitter, set the ypc-user-learn switch to the ypc (yamaha preset code) position. The remote control transmitter pro...
13 for other component control identify the remote control transmitter keys with your component’s keys. If these keys are identical, their function will be the same. On each key function, refer to the corresponding instruction on your component’s manual. ➊ tuner keys controls tuner +: selects higher...
14 remote control “learning” function (u.S.A., canada and general models of cx-2 only) the keys on this remote control transmitter can be programmed to “learn” key-functions from other remote control transmitters without losing the preset key functions. By using this feature, this unit can then be u...
15 1 set to the “learn” position. 2 press a key on this unit where a new function will be learned. 3 press and hold the key (on the other remote control transmitter) where the desired new function is. * when the transmit/learn indicator stops illuminating, the learning is finished. 4 repeat step 2 a...
16 1 set to the “user” position. 2 press and hold the clear button using the point of a mechanical pencil, etc. 3 press and hold the key where the learned function to be deleted is until the indicator flashes 3 times. To clear two or more functions, repeat step 2 and 3. Note if a key is not pressed ...
17 power supply [u.S.A. And canada models] ............................................Ac 120v, 60 hz [australia and u.K. Models] ............................................Ac 240v, 50 hz [europe model] ....................Ac 230v, 50 hz [general model] ..................Ac 110/120/220/240v, 50/60 ...
18 symptom the unit fails to turn on when the power switch is pressed. No sound or no picture. Only one side speaker outputs the sound. Sound “hums”. Sound level is low. The sound from the mc cartridge is too low using the bass, treble, balance and loudness (for cx-2 only) controls does not affect t...
Yamaha electronics corporation, usa 6660 orangethorpe ave., buena park, calif. 90620, u.S.A. Yamaha canada music ltd. 135 milner ave., scarborough, ontario m1s 3r1, canada yamaha electronik europa g.M.B.H. Siemensstr. 22-34, d-2084 rellingen bei hamburg, f.R. Of germany yamaha electronique france s....