1. DL manuals
  2. Yamaha
  3. Motorcycle
  4. DT125R
  5. Owner's Manual

Yamaha DT125R Owner's Manual

Other manuals for DT125R: Owner's Manual, Owner's Manual
Manual is about: DT 2001

Summary of DT125R

  • Page 1

    Printed on recycled paper printed in japan 2001·6–0.3 × 1(e) ! Owner’s manual 3mb-28199-e8 dt125r yamaha motor co., ltd..

  • Page 2

    Eau03338 introduction welcome to the yamaha world of motorcycling! As the owner of a dt125r, you are benefiting from yamaha’s vast experience and newest technolo- gy regarding the design and manufacture of high-quality products, which have earned yamaha a rep- utation for dependability. Please take ...

  • Page 3

    Eau00005 important manual information particularly important information is distinguished in this manual by the following notations: the safety alert symbol means attention! Become alert! Your safety is involved! Failure to follow warning instructions could result in severe injury or death to the mo...

  • Page 4

    Important manual information ew000002 w please read this manual carefully and completely before operating this motorcycle. 3mb-9-e8 6/13/01 10:55 am page 3.

  • Page 5

    Dt125r owner’s manual © 2001 by yamaha motor co., ltd. 1st edition, may 2001 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor co., ltd. Is expressly prohibited. Printed in japan. Eau03337 3mb-9-e8 6/13/01 10:55 am page 4.

  • Page 6

    Eau00009 table of contents give safety the right of way ............... 1-1 description .................................................. 2-1 left view ......................................................... 2-1 right view ....................................................... 2-2 controls and i...

  • Page 7

    Periodic maintenance and minor repair ................................................ 6-1 owner’s tool kit ............................................... 6-1 periodic maintenance and lubrication chart ... 6-2 removing and installing cowlings .................. 6-5 removing and installing panels .....

  • Page 8

    Table of contents specifications ............................................ 8-1 conversion table ............................................ 8-5 consumer information ........................... 9-1 identification numbers .................................... 9-1 key identification number ............

  • Page 9

    1-1 eau00021 q give safety the right of way 1 motorcycles are fascinating vehicles, which can give you an unsurpassed feeling of power and free- dom. However, they also impose certain limits, which you must accept; even the best motorcycle does not ignore the laws of physics. Regular care and mainte...

  • Page 10

    3mb-9-e8 6/13/01 10:55 am page 9.

  • Page 11

    2-1 eau00026 description 2 1. Headlight (page 6-36) 2. Radiator cap (page 6-14) 3. Fuel cock (page 3-9) 4. Air filter element (page 6-16) 5. Coolant reservoir tank (page 6-12) 6. Helmet holder (page 3-12) 7. Starter (choke) lever (page 3-10) 8. Shift pedal (page 3-4, 5-2) 9. Yeis (page 3-14) 10. Ypv...

  • Page 12

    2-2 description 2 11. Owner’s tool kit (page 6-1) 12. Fuse (page 6-35) 13. Battery (page 6-33) 14. 2-stroke engine oil tank (page 3-8) 15. Brake pedal (page 3-5, 6-23) 16. Shock absorber spring preload adjusting nut (page 3-12) 11 12 14 15 16 13 right view 3mb-9-e8 6/13/01 10:55 am page 11.

  • Page 13

    2-3 description 2 1. Clutch lever (page 3-4, 6-22) 2. Left handlebar switches (page 3-3) 3. Speedometer unit (page 3-2) 4. Coolant temperature gauge (page 3-3) 5. Tachometer (page 3-2) 6. Right handlebar switch (page 3-4) 7. Brake lever (page 3-5, 6-23) 8. Throttle grip (page 6-18, 6-29) 9. Fuel tan...

  • Page 14

    3-1 eau00027 instrument and control functions 3 eau00028 main switch the main switch controls the ignition and lighting systems. The various main switch positions are described below. Eau00036 on all electrical systems are supplied with power, and the engine can be started. The key cannot be removed...

  • Page 15

    3-2 eau01087 speedometer unit the speedometer unit is equipped with a speedometer, an odometer and a tripmeter. The speedometer shows riding speed. The odometer shows the total distance traveled. The tripmeter shows the distance traveled since it was last set to zero with the reset knob. The tripmet...

  • Page 16

    3-3 instrument and control functions 3 eau01652 coolant temperature gauge with the key in the “on” position, the coolant temperature gauge indicates the temperature of the coolant. The coolant temperature varies with changes in the weather and engine load. If the needle reaches or enters the red zon...

  • Page 17

    3-4 eau03890 engine stop switch “ # / $ ” set this switch to “ # ” before starting the engine. Set this switch to “ $ ” to stop the engine in case of an emer- gency, such as when the motorcycle overturns or when the throttle cable is stuck. Instrument and control functions 3 1 1. Engine stop switch ...

  • Page 18

    3-5 instrument and control functions 3 eau00158 brake lever the brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the han- dlebar grip. 1 1. Brake lever eau00162 brake pedal the brake pedal is on the right side of the motorcycle. To apply the rear br...

  • Page 19

    3-6 instrument and control functions 3 to install the fuel tank cap 1. Insert the fuel tank cap into the tank opening with the key insert- ed in the lock, and then turn the cap 1/3 turn clockwise. 2. Turn the key 1/4 turn clockwise, and then remove it. Note: the fuel tank cap cannot be installed unl...

  • Page 20

    3-7 instrument and control functions 3 ew000130 w 8 do not overfill the fuel tank, otherwise it may overflow when the fuel warms up and expands. 8 avoid spilling fuel on the hot engine. Eau00185 c c immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted s...

  • Page 21

    3-8 instrument and control functions 3 ec000114 c c the following precautions must be observed to prevent a fire hazard or other damages. 8 use only unleaded gasoline. The use of leaded gasoline will cause unrepairable damage to the catalytic converter. 8 never park the motorcycle near possible fire...

  • Page 22

    3-9 instrument and control functions 3 on with the lever in this position, fuel flows to the carburetor. Normal riding is done with the lever in this position. On fuel res off 1 on 1. Arrow mark positioned over “on” res this indicates reserve. If you run out of fuel while riding, move the lever to t...

  • Page 23

    3-10 instrument and control functions 3 eau03839 starter (choke) lever “ 1 ” starting a cold engine requires a rich- er air-fuel mixture, which is supplied by the starter (choke). Move the lever in direction a to turn on the starter (choke). Move the lever in direction b to turn off the starter (cho...

  • Page 24

    3-11 instrument and control functions 3 to unlock the steering 1. Open the steering lock cover, and then insert the key. 2. Push the key in, turn it 1/8 turn counterclockwise so that it moves out, and then release it. 3. Remove the key, and then close the lock cover. Eau01648 seat to remove the seat...

  • Page 25

    3-12 instrument and control functions 3 eau00261 helmet holder to open the helmet holder, insert the key into the lock, and then turn the key as shown. To lock the helmet holder, turn the key to the original position, and then remove it. Ew000030 w never ride with a helmet attached to the helmet hol...

  • Page 26

    3-13 instrument and control functions 3 3. Tighten the locknut to the speci- fied torque. Ec000018 c c always tighten the locknut against the adjusting nut, and then tighten the locknut to the specified torque. Eau00315 w this shock absorber contains highly pressurized nitrogen gas. For proper handl...

  • Page 27

    3-14 instrument and control functions 3 eau00320 carrier ew000032 w 8 do not exceed the load limit of 2 kg for the carrier. 8 do not exceed the maximum load of 180 kg/178 kg (for ch, a) for the vehicle. 1 1. Carrier eau00325 yeis handling precautions improper installation of or damage to any part of...

  • Page 28

    3-15 instrument and control functions 3 ec000023 c c the ypvs has been set and exten- sively tested at the yamaha facto- ry. Changing these settings with- out sufficient technical knowledge may result in poor performance of or damage to the engine. Ypvs operation noises can be heard in the following...

  • Page 29

    3-16 eau03571 ignition circuit cut-off system the ignition circuit cut-off system (comprising the sidestand switch and neutral switch) has the following func- tions. 8 it prevents starting when the transmission is in gear and the sidestand is still down. 8 it cuts the running engine when the transmi...

  • Page 30

    3-17 instrument and control functions 3 with the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is set to “ # ”. 3. Turn the key to “on”. 4. Shift the transmission into the neutral position. 5. Push the kickstarter lever down. Does the engine start? The neutr...

  • Page 31

    4-1 eau01114 pre-operation checks 4 the condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpect- edly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leak- age or loss of tire a...

  • Page 32

    4-2 pre-operation checks 4 clutch • check operation. • lubricate cable if necessary. • check lever free play. • adjust if necessary. 3-4, 6-22 throttle grip • make sure that operation is smooth. • check free play. • if necessary, have yamaha dealer make adjustment or lubricate. 6-18, 6-29 control ca...

  • Page 33

    4-3 pre-operation checks 4 note: pre-operation checks should be made each time the motorcycle is used. Such an inspection can be accomplished in a very short time; and the added safety it assures is more than worth the time involved. Ewa00033 w if any item in the pre-operation check list is not work...

  • Page 34

    5-1 eau00372 operation and important riding points 5 eau00373 w 8 become thoroughly familiar with all operating controls and their functions before riding. Consult a yamaha dealer regarding any control or func- tion that you do not thorough- ly understand. 8 never start the engine or oper- ate it in...

  • Page 35

    5-2 operation and important riding points 5 4. Turn the starter (choke) on and completely close the throttle. (see page 3-10 for starter (choke) operation.) 5. Start the engine by pushing the kickstarter lever down. 6. After starting the engine, move the starter (choke) lever back halfway. Eca00045 ...

  • Page 36

    5-3 operation and important riding points 5 ec000048 c c 8 even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long distances. The transmission is properly lubricated only when the engine is running. Inadequ...

  • Page 37

    5-4 operation and important riding points 5 eau00436 engine break-in there is never a more important peri- od in the life of your engine than the period between 0 and 1,000 km. For this reason, you should read the fol- lowing material carefully. Since the engine is brand new, do not put an excessive...

  • Page 38

    5-5 operation and important riding points 5 eau00458 parking when parking, stop the engine, remove the key from the main switch, and then turn the fuel cock lever to “off”. Ew000058 w 8 since the engine and exhaust system can become very hot, park in a place where pedestri- ans or children are not l...

  • Page 39

    6-1 eau00462 periodic maintenance and minor repair 6 eau00464 safety is an obligation of the owner. Periodic inspection, adjustment and lubrication will keep your vehicle in the safest and most efficient condi- tion possible. The most important points of inspection, adjustment, and lubrication are e...

  • Page 40

    6-2 periodic maintenance and minor repair 6 no. Item check or maintenance job odometer reading ( × 1,000 km) annual check 1 6 12 18 24 1 * fuel line • check fuel hoses for cracks or damage. √ √ √ √ √ 2 spark plug • replace. √ √ √ √ √ 3 air filter element • clean. √ √ • replace. √ √ 4 * battery • che...

  • Page 41

    6-3 periodic maintenance and minor repair 6 9 * wheels • check runout, spoke tightness and for damage. • tighten spokes if necessary. √ √ √ √ 10 * tires • check tread depth and for damage. • replace if necessary. • check air pressure. • correct if necessary. √ √ √ √ √ 11 * wheel bearings • check bea...

  • Page 42

    6-4 periodic maintenance and minor repair 6 eau03884 note: 8 the air filter needs more frequent service if you are riding in unusually wet or dusty areas. 8 hydraulic brake service 9 regularly check and, if necessary, correct the brake fluid level. 9 every two years replace the internal components o...

  • Page 43

    6-5 periodic maintenance and minor repair 6 eau01065 removing and installing cowlings the cowlings shown above need to be removed to perform some of the maintenance jobs described in this chapter. 2 1 1. Cowling a 2. Cowling b eau01534 cowling a to remove the cowling remove the cowling screws, and t...

  • Page 44

    6-6 periodic maintenance and minor repair 6 to install the cowling place the cowling in the original posi- tion, and then install the screws. To install the cowling place the cowling in the original posi- tion, and then install the screws. Eau01534 cowling b to remove the cowling remove the cowling ...

  • Page 45

    6-7 periodic maintenance and minor repair 6 eau01534 cowling c to remove the cowling remove the cowling screws, and then pull the cowling off as shown. 1 1. Screw ( × 3) eau01122 removing and installing panels the panels shown above need to be removed to perform some of the maintenance jobs describe...

  • Page 46

    6-8 periodic maintenance and minor repair 6 refer to this section each time a panel needs to be removed and installed. 1 1. Panel b to install the panel place the panel in the original posi- tion, and then install the screw. 1 2 1. Screw 2. Panel b eau04003 panels a and b to remove one of the panels...

  • Page 47

    6-9 periodic maintenance and minor repair 6 eau01833 checking the spark plug the spark plug is an important engine component, which is easy to check. Since heat and deposits will cause any spark plug to slowly erode, the spark plug should be removed and checked in accordance with the periodic mainte...

  • Page 48

    6-10 periodic maintenance and minor repair 6 to install the spark plug 1. Measure the spark plug gap with a wire thickness gauge and, if necessary, adjust the gap to specification. 2. Clean the surface of the spark plug gasket and its mating sur- face, and then wipe off any grime from the spark plug...

  • Page 49

    6-11 periodic maintenance and minor repair 6 3. Wait a few minutes until the oil settles, and then check the oil level through the check window located at the right side of the crankcase. Note: the transmission oil should be at or above the minimum level mark. 4. If the oil is below the minimum leve...

  • Page 50

    6-12 periodic maintenance and minor repair 6 ec000077 c c 8 in order to prevent clutch slip- page (since the transmission oil also lubricates the clutch), do not mix any chemical addi- tives with the oil. 8 make sure that no foreign material enters the transmis- sion. 6. Start the engine, and then l...

  • Page 51

    6-13 periodic maintenance and minor repair 6 4. If the coolant is at or below the minimum level mark, open the reservoir cap, add coolant to the maximum level mark, and then close the reservoir cap. Ew000067 w never attempt to remove the radia- tor cap when the engine is hot. 5. Install the panel. N...

  • Page 52

    6-14 periodic maintenance and minor repair 6 eau03101 changing the coolant 1. Put the motorcycle on a level place. 2. Remove cowling b and panel a. (see page 6-6–6-8 for cowling and panel removal and installa- tion procedures.) 3. Remove the radiator cap stopper bolt and the radiator cap. 1 2 1. Rad...

  • Page 53

    6-15 periodic maintenance and minor repair 6 8. Install the reservoir tank hose. 9. Pour the recommended coolant into the radiator until it is full. 10. Install the radiator cap. 11. Run the engine several minutes. Stop the engine and recheck the coolant level in the radiator. If it is low, add more...

  • Page 54

    6-16 periodic maintenance and minor repair 6 eau04233 cleaning the air filter element the air filter element should be cleaned at the intervals specified in the periodic maintenance and lubrica- tion chart. Clean the air filter element more frequently if you are riding in unusually wet or dusty area...

  • Page 55

    6-17 periodic maintenance and minor repair 6 7. Pull the sponge material over the frame. 8. Install the air filter element onto the guide, and then tighten the wing nut. 9. Insert the air filter element into the case. 10. Install the air filter case cover by installing the screws. 11. Install the pa...

  • Page 56

    6-18 periodic maintenance and minor repair 6 b a 1 1. Throttle stop screw to increase the engine idling speed, turn the screw in direction a . To decrease the engine idling speed, turn the screw in direction b . Note: if the specified idling speed cannot be obtained as described above, have a yamaha...

  • Page 57

    6-19 periodic maintenance and minor repair 6 eau04259 tires to maximize the performance, dura- bility, and safe operation of your motorcycle, note the following points regarding the specified tires. Tire air pressure the tire air pressure should be checked and, if necessary, adjusted before each rid...

  • Page 58

    6-20 periodic maintenance and minor repair 6 tire inspection the tires must be checked before each ride. If the center tread depth reaches the specified limit, if the tire has a nail or glass fragments in it, or if the sidewall is cracked, have a yamaha dealer replace the tire imme- diately. Note: t...

  • Page 59

    6-21 periodic maintenance and minor repair 6 eau00685 spoke wheels to maximize the performance, dura- bility, and safe operation of your motorcycle, note the following points regarding the specified wheels. 8 the wheel rims should be checked for cracks, bends or warpage, and the spokes for looseness...

  • Page 60

    6-22 periodic maintenance and minor repair 6 eau00694 adjusting the clutch lever free play the clutch lever free play should measure 10–15 mm as shown. Periodically check the clutch lever free play and, if necessary, adjust it as follows. 1. Loosen the locknut at the clutch lever. 2. To increase the...

  • Page 61

    6-23 periodic maintenance and minor repair 6 eau00712 adjusting the brake pedal position the top of the brake pedal should be positioned approximately 15 mm below the top of the footrest as shown. Periodically check the brake pedal position and, if necessary, have a yamaha dealer adjust it. A 1 1. F...

  • Page 62

    6-24 periodic maintenance and minor repair 6 ew000109 w a soft or spongy feeling in the brake pedal can indicate the pres- ence of air in the hydraulic system. If there is air in the hydraulic sys- tem, have a yamaha dealer bleed the system before operating the motorcycle. Air in the hydraulic syste...

  • Page 63

    6-25 periodic maintenance and minor repair 6 eau00724 front brake pads each front brake pad is provided with a wear indicator, which allows you to check the brake pad wear without having to disassemble the brake. To check the brake pad wear, check the position of the wear indicator while applying th...

  • Page 64

    6-26 periodic maintenance and minor repair 6 observe these precautions: 8 when checking the fluid level, make sure that the top of the brake fluid reservoir is level. 8 use only the recommended qual- ity brake fluid, otherwise the rub- ber seals may deteriorate, caus- ing leakage and poor braking pe...

  • Page 65

    6-27 periodic maintenance and minor repair 6 eau00744 drive chain slack the drive chain slack should be checked before each ride and adjust- ed if necessary. To check the drive chain slack 1. Place the motorcycle on a level surface and hold it in an upright position. Note: when checking and adjustin...

  • Page 66

    6-28 periodic maintenance and minor repair 6 note: make sure that both adjusting plates are in the same position for proper wheel alignment. Ec000096 c c improper drive chain slack will overload the engine as well as other vital parts of the motorcycle and can lead to chain slippage or breakage. To ...

  • Page 67

    6-29 periodic maintenance and minor repair 6 eau04034 checking and lubricating the throttle grip and cable the operation of the throttle grip should be checked before each ride. In addition, the cable should be lubri- cated or replaced at the intervals specified in the periodic maintenance chart. Ea...

  • Page 68

    6-30 periodic maintenance and minor repair 6 eau00774 adjusting the autolube pump the autolube pump is a vital and sophisticated component of the engine, which must be adjusted by a yamaha dealer at the intervals speci- fied in the periodic maintenance and lubrication chart. Eau03370 checking and lu...

  • Page 69

    6-31 periodic maintenance and minor repair 6 eau02939 checking the front fork the condition and operation of the front fork must be checked as follows at the intervals specified in the peri- odic maintenance and lubrication chart. To check the condition ew000115 w securely support the motorcycle so ...

  • Page 70

    6-32 periodic maintenance and minor repair 6 2. Hold the lower ends of the front fork legs and try to move them forward and backward. If any free play can be felt, have a yamaha dealer check or repair the steering. Eau01144 checking the wheel bearings the front and rear wheel bearings must be checke...

  • Page 71

    6-33 periodic maintenance and minor repair 6 note: make sure that the motorcycle is positioned straight up when checking the electrolyte level. 2. Check the electrolyte level in the battery. Note: the electrolyte should be between the minimum and maximum level marks. 1 2 1. Maximum level mark 2. Min...

  • Page 72

    6-34 periodic maintenance and minor repair 6 to store the battery 1. If the motorcycle will not be used for more than one month, remove the battery, fully charge it, and then place it in a cool, dry place. 2. If the battery will be stored for more than two months, check the specific gravity of the e...

  • Page 73

    6-35 periodic maintenance and minor repair 6 ec000103 c c do not use a fuse of a higher amperage rating than recommend- ed to avoid causing extensive damage to the electrical system and possibly a fire. 3. Turn the key to “on” and turn on the electrical circuits to check if the devices operate. 4. I...

  • Page 74

    6-36 periodic maintenance and minor repair 6 4. Remove the headlight bulb hold- er by turning it counterclockwise, and then remove the defective bulb. 1 1. Headlight bulb holder 3. Disconnect the headlight cou- pler, and then remove the head- light bulb cover. 1 2 1. Headlight coupler 2. Headlight b...

  • Page 75

    6-37 periodic maintenance and minor repair 6 eau03497 replacing a turn signal light bulb 1. Remove the turn signal light lens by removing the screw. 2. Remove the defective bulb by pushing it in and turning it coun- terclockwise. 3. Insert a new bulb into the socket, push it in, and then turn it clo...

  • Page 76

    6-38 periodic maintenance and minor repair 6 ec000108 c c do not overtighten the screws, otherwise the lens may break. Eau01623 replacing the tail/brake light bulb 1. Remove the tail/brake light lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it coun- terclockw...

  • Page 77

    6-39 periodic maintenance and minor repair 6 eau00898 front wheel to remove the front wheel ew000122 w 8 it is advisable to have a yamaha dealer service the wheel. 8 securely support the motorcy- cle so that there is no danger of it falling over. 1. Remove the brake disc cover by removing the screws...

  • Page 78

    6-40 periodic maintenance and minor repair 6 eca00048 c c do not apply the brake after the wheel has been removed together with the brake disc, otherwise the brake pads will be forced shut. 2. Disconnect the speedometer cable from the front wheel. 3. Lift the front wheel off the ground according to ...

  • Page 79

    6-41 periodic maintenance and minor repair 6 7. After tightening the holder nuts, while applying the front brake, push down on the handlebars several times to check if the front fork compress and rebounds smoothly. 8. Connect the speedometer cable. 6. Tighten the axle holder nuts to the specified ti...

  • Page 80

    6-42 periodic maintenance and minor repair 6 eca00048 c c do not apply the brake after the wheel has been removed together with the brake disc, otherwise the brake pads will be forced shut. Eau04237 rear wheel wheel (rear) ew000122 w 8 it is advisable to have a yamaha dealer service the wheel. 8 sec...

  • Page 81

    6-43 periodic maintenance and minor repair 6 eau03087 troubleshooting although yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur during operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and lo...

  • Page 82

    6-44 periodic maintenance and minor repair 6 check if there is fuel 1. Fuel enough fuel. No fuel. Go to compression check. Supply fuel. Engine doesn’t start, go to compression check. Use kickstarter. 2. Compression there is compression. No compression. Go to ignition check. Ask a yamaha dealer to re...

  • Page 83

    6-45 periodic maintenance and minor repair 6 wait until the check the coolant level in the level is ok. Level is low, check the no leakage. Ask a yamaha dealer to inspect add coolant. (see note.) restart the engine. If the engine overheats again, ask a engine has cooled. Reservoir tank and/or radiat...

  • Page 84

    7-1 eau03521 motorcycle care and storage 7 care while the open design of a motorcy- cle reveals the attractiveness of the technology, it also makes it more vul- nerable. Rust and corrosion can develop even if high-quality compo- nents are used. A rusty exhaust pipe may go unnoticed on a car, however...

  • Page 85

    7-2 motorcycle care and storage 7 8 do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abra- sive cleaning products, sol- vent or thinner, fuel (gasoline), rust removers or inhibitors, brake fluid, antifreeze or...

  • Page 86

    7-3 motorcycle care and storage 7 after cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth. 2. Immediately dry the drive chain and lubricate it to prevent it from rusting. 3. Use a chrome polish to shine chrome, aluminum and stainless- steel parts, including the exhaust system. (eve...

  • Page 87

    7-4 motorcycle care and storage 7 storage short-term always store your motorcycle in a cool, dry place and, if necessary, pro- tect it against dust with a porous cover. Eca00014 c c 8 storing the motorcycle in a poorly ventilated room or cov- ering it with a tarp, while it is still wet, will allow w...

  • Page 88

    7-5 motorcycle care and storage 7 6. Lubricate all control cables and the pivoting points of all levers and pedals as well as of the sidestand/centerstand. 7. Check and, if necessary, correct the tire air pressure, and then lift the motorcycle so that both of its wheels are off the ground. Alternati...

  • Page 89

    8-1 eau01038 specifications 8 specifications model dt125r dimensions overall length 2,170 mm 2,235 mm (n, s, sf, ch, a only) overall width 830 mm overall height 1,255 mm seat height 885 mm wheel base 1,415 mm ground clearance 315 mm minimum turning radius 2,100 mm basic weight (with oil and full fue...

  • Page 90

    8-2 specifications 8 carburetor manufacturer mikuni model × quantity tm28ss × 1 spark plug manufacturer/model ngk / br9es ngk / br8es (ch, a only) spark plug gap 0.7–0.8 mm clutch type wet, multiple-disc transmission primary reduction system helical gear primary reduction ratio 71/22 (3.227) seconda...

  • Page 91

    8-3 specifications 8 90 kg load–maximum load* front 150 kpa (1.50 kgf/cm 2 , 1.50 bar) rear 175 kpa (1.75 kgf/cm 2 , 1.75 bar) off-road riding front 125 kpa (1.25 kgf/cm 2 , 1.25 bar) rear 150 kpa (1.50 kgf/cm 2 , 1.50 bar) *total weight of rider, passenger, cargo and accessories wheels front type s...

  • Page 92

    8-4 specifications 8 battery type gm3-3b voltage, capacity 12 v, 3 ah headlight type conventional incandescent bulb bulb voltage, wattage × quantity headlight 12 v, 45/40 w × 1 tail/brake light 12 v, 5/21 w × 1 front turn signal light 12 v, 21 w × 2 rear turn signal light 12 v, 21 w × 2 auxiliary li...

  • Page 93

    8-5 specifications 8 eau03941 conversion table conversion table all specification data in this manual are listed in si and metric units. Use this table to convert metric unit data to imperial unit data. Ex. Metric multiplier imperial ** mm × 0.03937 = ** in 2 mm × 0.03937 = 0.08 in metric to imperia...

  • Page 94

    9-1 eau01039 consumer information 9 eau02944 identification numbers record the key identification number, vehicle identification number and model label information in the spaces provided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the vehicle is stole...

  • Page 95

    9-2 consumer information 9 eau03757 model label the model label is affixed to the loca- tion shown. Record the information on this label in the space provided. This information will be needed when ordering spare parts from a yamaha dealer. 1 1. Model label 3mb-9-e8 6/13/01 10:55 am page 94.

  • Page 96

    Printed on recycled paper printed in japan 2001·6–0.3 × 1(e) ! Owner’s manual 3mb-28199-e8 dt125r yamaha motor co., ltd..