E owner’s manual 10 0 peak +8 +5 +3 +1 0 –1 –3 –5 –7 –10 –15 –20 graphic equalizer digital effect 6 0 6 max min program phantom (+48v) phones/c.R.Out 10 0 st 2 10 0 st mono bridge power amp tape in limiter l r mono +4db foot sw moni moni (mono) pamp in 2 effect +4db phones/ c-r out (+4db) level l/br...
Fcc information (u.S.A.) 1. Important notice: do not modify this unit! This product, when installed as indicated in the instructions contained in this manual, meets fcc requirements. Modifications not expressly approved by yamaha may void your authority, granted by the fcc, to use the product. 2. Im...
2 emx2000—owner’s manual introduction thank you for purchasing the yamaha emx2000 powered mixer. In order to take full advantage of the emx2000 and enjoy long, trouble-free performance, please read this owner’s manual carefully, and keep it in a safe place for future reference. Features • the emx200...
3 emx2000—owner’s manual precautions 1. Avoid excessive heat, humidity, dust and vibration keep the unit away from locations where it is likely to be exposed to high temperatures or humidity — such as near radiators, stoves, etc. Also avoid locations which are subject to exces- sive dust accumulatio...
4 emx2000—owner’s manual front and rear panel control panel ■ channel control section in this section, you can adjust equalization (fre- quency response), volume level, effect and moni- tor output levels for the input signal of each channel. 1 gain control use this knob to adjust the sensitivity acc...
5 emx2000—owner’s manual 6 effect control (effect) for each channel, this controls the amount of sig- nal that is sent to the effect bus. The signal of the effect bus is sent to the effect jack (input/output panel a ). It is also sent to the built-in effect when the on switch p in the effect section...
6 emx2000—owner’s manual ■ master control section in this section, you can adjust the final level of the outputs. E moni 1 (monitor 1) fader the moni 1 fader adjusts the final level of the signal sent from the monitor 1 bus to the moni 1 jack (input/output panel 9 ). If the power amp select switch v...
7 emx2000—owner’s manual ■ digital effect section this section enables you to turn the built-in digi- tal effect on/off and select the effect type. M moni 1/2 (monitor 1/2) control this knob adjusts the level of the return signal that is sent from the built-in digital effect to the monitor 1/2 buses...
8 emx2000—owner’s manual u level controls these knobs enable you to adjust the level of the signals input from the mixer section to the power amp section. Rotating the knob clockwise will raise the level of the input signal. Use a screw- driver of a width of 3mm or less to adjust the knob. If an ext...
9 emx2000—owner’s manual input/output panel 1 channel input jacks (mic, line) 1~8 these are the input jacks for channels 1~8. By using the gain control (control panel 1) you can connect any of the jacks to a wide range of sources, from mics to line-level devices (including synthesizers and rhythm ma...
10 emx2000—owner’s manual 3 channel input jacks 9~12a channel input jacks 9~12b these are the input jacks for channels 9/10~11/12 and are used to connect to the stereo output jacks of electronic instruments, cassette decks, or cd players. Use the a/b switch (control panel 2) to select phone jacks (a...
11 emx2000—owner’s manual rear panel 1 speakers (speaker output) jacks speakers can be connected to these jacks. The type of signals output, the number of speak- ers you can connect, and acceptable impedance differ depending on the setting of the power amp select switch (control panel v). • when the...
12 emx2000—owner’s manual connections when connecting various devices, be sure to use cables and plugs of the appropriate standard. Connecting speakers there are three ways in which speakers can be connected to the emx2000. 1 connecting a single speaker to each of the l and r jacks: a single speaker...
13 emx2000—owner’s manual basic operation connecting microphones and instruments 1 before connecting mics or instruments, make sure that the power of all equip- ment (where applicable) is turned off. Also make sure that each channel fader and the faders in the master section are turned down. Check t...
14 emx2000—owner’s manual example setups this section provides some ways in which the emx2000 can be used, and explains connections and operation. As a band pa here is an example of using the emx2000 as a small pa for a band. In this example, the monitor speakers are being sent a mix that is indepen...
15 emx2000—owner’s manual as a conference/entertainment hall sound system here is an example of using the emx2000 as a conference or entertainment hall sound system. ■ connections • connect mics to channel inputs 1~8. • a cd player/ld player/cassette deck can also be connected to the input jacks of ...
16 emx2000—owner’s manual ■ sending an independent mix to the monitor speakers 1 set the moni 1 or moni 2 fader to the “10” position. 2 raise the moni 1 or moni 2 controls for the channels that you wish to hear from the monitor speakers. 3 use the moni 1 or moni 2 fader of the master section to adju...
17 emx2000—owner’s manual specifications ■ general specifications maximum output power stereo: 200 w+200 w/4 Ω @0.5% thd at 1 khz bridge: 400 w/8 Ω @0.5% thd at 1 khz frequency response 20 hz~20 khz +1 db, –3 db @1 w output into 8 Ω (speaker out) all channel gain controls at minimum. 20 hz~20 khz +1...
18 emx2000—owner’s manual ■ input specifications ■ output specifications specifications are subject to change without prior notice. 1. Sensitivity is the lowest level that can produce an output of +4 db (1.23 v) or the nominal output level when the unit is set at maximum gain. 2. Xlr type connectors...
19 emx2000—owner’s manual dimensions unit: mm 167.6 w: 480 d: 454 h: 125 277.7.
20 emx2000—owner’s manual block/level diagram pan pan moni 1,mono pfl 0 db db moni 1 moni 2 moni 1 moni 2 p amp l p amp r moni 1 mono phones (3mw/40 Ω ) st, mono, monitor, effect, c.R.Out, p amp in (+4db) phones/c.R.Out effect c.R.Monitor l, r bridge 16 15 14 3 2 1 (min max) p amp in l/bridge graphi...
Yamaha corporation vz42360 r1 1 ip 24 pro audio division, #18/3 p.O. Box 3, hamamatsu, 430-8651, japan np printed in taiwan.
