Owner’s manual e see rear panel caution. Power phantom +48v on off +6 +3 0 –5 –10 +6 +3 0 –5 –10 • 6 • 0 • 6 • moni on l r l r limiter limiter vocal l hall s hall l+r bridge stereo main master effect rtn monitor effect rec out tape in output l l l r r r l (mono) r main(stereo) monitor aux in powered...
Fcc information (u.S.A.) 1. Important notice: do not modify this unit! This product, when installed as indicated in the instructions contained in this manual, meets fcc requirements. Modifications not expressly approved by yamaha may void your authority, granted by the fcc, to use the product. 2. Im...
Important 3 emx860st—owner’s manual important read the following before operating the emx860st warnings • do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock may result. • connect this unit’s power cord only to an ac outlet of the type stated in this owner...
4 important emx860st—owner’s manual operating notes • the digital circuits of this unit may induce a slight noise into nearby radios and tvs. If noise occurs, relocate the affected equipment. • using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone away from the...
Introduction 5 emx860st—owner’s manual introduction thank you for purchasing the yamaha emx860st powered mixer. The emx860st has the following features. In order to take full advantage of the emx860st and enjoy long and trouble-free per- formance, please read this owner’s manual carefully, and keep ...
6 front and rear panel emx860st—owner’s manual front and rear panel control panel ■ channel section use these controls to adjust factors such as the equalization, (frequency response), volume, effect and monitor output level for the input sig- nal to each channel. 1 equalizer controls (high, mid, lo...
Control panel 7 emx860st—owner’s manual ■ digital effect section this section allows you to turn the built-in digital effect on/off and to select the effect type. 7 effect select switch select the effect type for the built-in digital effect. 8 digital effect on switch use this switch to turn the dig...
8 front and rear panel emx860st—owner’s manual ■ monitor section this section allows you to adjust the tone and volume of the monitor bus, and specify the mix level of the built-in digital effect. 0 graphic equalizer the emx860st has a 7-band graphic equalizer for adjusting the frequency response of...
Control panel 9 emx860st—owner’s manual ■ power amp section this section allows you to select the signals that will be output from the built-in three-channel power amplifier, and to select the bridge mode. J limiter indicator this indicator lights up when the level of the sig- nal output from the po...
10 front and rear panel emx860st—owner’s manual input/output panel 1 channel input jacks (hi-z, lo-z) 1–6 these are the input jacks for channels 1–6. By using the pad switches (control panel 6) you can connect any of the jacks to a wide range of sources from mics to line level devices (synthesiz- er...
Input/output panel 11 emx860st—owner’s manual 5 aux in/tape in jacks these are input jacks that allow the signal from an external device to be added to the main out- put. • aux in jacks: connect these jacks to the output jacks of an external effects processor. If the effects processor has a stereo o...
12 front and rear panel emx860st—owner’s manual rear panel 1 speakers monitor jacks connect monitoring speakers to these jacks. Moni bus signals adjusted at the monitor section are output from these jacks. The speak- ers monitor a and b jacks are internally con- nected in parallel, and output the sa...
Connections 13 emx860st—owner’s manual connections when connecting various devices, make sure the cables and plugs have the correct rating. Be sure to use cables designed for the purpose when you connect speakers to speaker jacks. ■ connecting monitoring speakers you can connect one or two speakers ...
14 connections emx860st—owner’s manual ■ example connections rec out tape in output l l l r r r l (mono) r main(stereo) monitor aux in powered mixer foot sw mic lo-z hi-z line effect out input to main l r (mono) mic line l r (mono) lo-z hi-z lo-z hi-z lo-z hi-z lo-z hi-z lo-z hi-z cassette deck foot...
Basic operation 15 emx860st—owner’s manual basic operation connecting microphones and instruments 1 before connecting mics or instruments, make sure that the power of all equip- ment (where applicable) is turned off. Also make sure that the level controls of each channel of the emx860st and the mast...
16 example setups emx860st—owner’s manual example setups this section provides some ways in which the emx860st can be used, and explains connections and opera- tion. As a conference pa system/installed sound system this example shows the emx860st used as a conference pa system or sound system. A sou...
As a conference pa system/installed sound system 17 emx860st—owner’s manual playing back a cd player 1 turn the power on in the order of periph- eral devices ➞ emx860st. 2 adjust the master control of the main section to the √ √ √ √ position. 3 start playback on the cd player, and use the main secti...
18 example setups emx860st—owner’s manual as a band pa here is an example of using the emx860st as a small pa for a band. In this example, an external effect such as delay or reverb is also being used. Connections • connect mics or instruments, such as keyboards, to the channel input jacks 1–8. • co...
As a band pa 19 emx860st—owner’s manual using an external effect 1 set the effect section effect out con- trol to the √ √ √ √ position. 2 raise the effect controls for the channels to which you want the external effect to be applied. 3 adjust the input level of the external effect so that the sound ...
20 troubleshooting emx860st—owner’s manual troubleshooting the following table describes the possible malfunctions of this device, and the appropriate actions to be taken in each case. Problem cause action sound is no longer out- put from the speakers. The power indicator is dark. The load on this d...
Specifications 21 emx860st—owner’s manual specifications ■ general specifications maximum output power main stereo: 135 w+135 w/8 Ω @0.5% thd at 1 khz, 200 w+200 w/4 Ω @0.5% thd at 1 khz main bridge: 400 w/8 Ω @0.5% thd at 1 khz monitor: 135 w/8 Ω @0.5% thd at 1 khz, 200 w/4 Ω @0.5% thd at 1 khz fre...
22 specifications emx860st—owner’s manual ■ input specifications ■ output specifications • all output jacks are unbalanced. • 0 db=0.775 vrms, 0 dbv=1 vrms. Specifications are subject to change without prior notice. *1. Sensitivity is the lowest level that can produce an output of +4 db (1.23 v) or ...
Dimensions 23 emx860st—owner’s manual ■ dimensions ■ block and level diagram 308 16 h:324 16 w:497 d:275 unit: mm hi-z [–10db] line [–10db] max.Output power(200w, 4 Ω ) limiter l, r, monitor[+24db] rtn effect rtn effect pan bal/ main, monitor, att tape in aux in [–10db] tape in [–10dbv] clip level [...
Yamaha corporation v296250 r0 1 ip 24 pro audio division, #18/3 p.O. Box 3, hamamatsu, 430-8651, japan printed in taiwan.
