1. DL manuals
  2. Yamaha
  3. Motorcycle
  4. FZ6-NAHG
  5. Owner's Manual

Yamaha FZ6-NAHG Owner's Manual

Other manuals for FZ6-NAHG: Owner's Manual
Manual is about: 2008

Summary of FZ6-NAHG

  • Page 1

    5s5-28199-e1 fz6-nhg fz6-nahg owner’s manual.

  • Page 2

    Eau26944 declaration of conformity yamaha motor electronics co., ltd. 1450-6, mori, mori-machi, shuchi-gun, shizuoka-ken, 437-0292 japan general manager of quality assurance div. 1 version up the norm of en60950 to en60950-1 to change company name 27 feb. 2006 1 mar. 2007 2 3 revision record no. Con...

  • Page 3: Introduction

    Introduction eau10100 welcome to the yamaha world of motorcycling! As the owner of the fz6-nhg/fz6-nahg, you are benefiting from yamaha’s vast experience and newest technology re- garding the design and manufacture of high-quality products, which have earned yamaha a reputation for dependability. Pl...

  • Page 4: Important Manual Information

    Important manual information eau10151 particularly important information is distinguished in this manual by the following notations: note: ● this manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle is subsequently sold. ● yamaha continuall...

  • Page 5: Important Manual Information

    Important manual information eau10200 fz6-nhg/fz6-nahg owner’s manual ©2007 by yamaha motor co., ltd. 1st edition, june 2007 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor co., ltd. Is expressly prohibited. Printed in japan. U5s5e1e0.Book page ...

  • Page 6: Table Of Contents

    Table of contents safety information ..................1-1 description ..................................2-1 left view ..........................................2-1 right view ........................................2-2 controls and instruments.................2-3 instrument and control functions .....

  • Page 7: Table of Contents

    Table of contents replacing a turn signal light bulb ...........................................6-34 replacing the license plate light bulb ...........................................6-34 replacing the auxiliary light bulb ...........................................6-35 supporting the motorcycle ......

  • Page 8: Safety Information

    1-1 1 safety information eau10281 motorcycles are single track vehicles. Their safe use and operation are dependent upon the use of proper riding techniques as well as the ex- pertise of the operator. Ev- ery operator should know the following requirements before riding this motor- cycle. He or she ...

  • Page 9: Safety Information

    Safety information 1-2 1 due to excessive speed or un- dercornering (insufficient lean an- gle for the speed). • always obey the speed limit and never travel faster than warrant- ed by road and traffic conditions. • always signal before turning or changing lanes. Make sure that other motorists can s...

  • Page 10: Safety Information

    Safety information 1-3 1 loading the total weight of the operator, pas- senger, accessories and cargo must not exceed the maximum load limit. When loading within this weight limit, keep the following in mind: ● cargo and accessory weight should be kept as low and close to the motorcycle as possible....

  • Page 11: Safety Information

    Safety information 1-4 1 tor and may limit control ability, therefore, such accessories are not recommended. ● use caution when adding electri- cal accessories. If electrical acces- sories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause ...

  • Page 12: Description

    Description 2-1 2 eau10410 left view 1. Main fuse (page 6-30) 2. Fuse box 2 (fz6-nahg) (page 6-30) 3. Battery (page 6-29) 4. Air filter element (page 6-13) 5. Idle adjusting screw (page 6-15) 6. Shock absorber assembly spring preload adjusting ring (page 3-20) 7. Owner’s tool kit (page 6-1) 8. Stora...

  • Page 13: Description

    Description 2-2 2 eau10420 right view 1. Fuse box 1 (page 6-30) 2. Rear brake fluid reservoir (page 6-21) 3. Engine oil filler cap (page 6-7) 4. Front brake fluid reservoir (page 6-21) 5. Radiator cap (page 6-10) 6. Coolant reservoir (page 6-10) 7. Coolant drain bolt (page 6-11) 8. Dipstick (page 6-...

  • Page 14: Description

    Description 2-3 2 eau10430 controls and instruments 1. Clutch lever (page 3-14) 2. Left handlebar switches (page 3-13) 3. Main switch/steering lock (page 3-2) 4. Multi-function meter unit (page 3-8) 5. Right handlebar switches (page 3-13) 6. Throttle grip (page 6-16) 7. Brake lever (page 3-15) u5s5e...

  • Page 15

    Instrument and control functions 3-1 3 eau10974 immobilizer system this vehicle is equipped with an immo- bilizer system to help prevent theft by re-registering codes in the standard keys. This system consists of the fol- lowing. ● a code re-registering key (with a red bow) ● two standard keys (with...

  • Page 16

    Instrument and control functions 3-2 3 ● keep other immobilizer system keys away from the main switch as they may cause signal inter- ference. Eau10471 main switch/steering lock the main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. Note: be sure ...

  • Page 17

    Instrument and control functions 3-3 3 to lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “off” po- sition, and then turn it to “lock” while still pushing it. 3. Remove the key. To unlock the steering push the key in, and then turn it to “off” while stil...

  • Page 18

    Instrument and control functions 3-4 3 eau11003 indicator and warning lights eau11030 turn signal indicator lights “ ” and “ ” the corresponding indicator light flash- es when the turn signal switch is pushed to the left or right. Eau11060 neutral indicator light “ ” this indicator light comes on wh...

  • Page 19

    Instrument and control functions 3-5 3 caution: eca10020 do not operate the engine if it is overheated. U5s5e1e0.Book page 5 friday, june 22, 2007 1:03 pm.

  • Page 20

    Instrument and control functions 3-6 3 coolant temperature display conditions what to do under 39 °c (under 103 °f) message “lo” is displayed. Ok. Go ahead with riding. 40–116 °c (104–242 °f) temperature is displayed. Ok. Go ahead with riding. 117–139 °c (243–283 °f) temperature display flashes. War...

  • Page 21

    Instrument and control functions 3-7 3 eau11530 engine trouble warning light “ ” this warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a yamaha dealer check the self- diagnosis system. (see page 3-8 for an explanation of the self...

  • Page 22

    Instrument and control functions 3-8 3 eau39426 multi-function meter unit warning ewa12421 be sure to stop the vehicle before making any setting changes to the multi-function meter unit. The multi-function meter unit is equipped with the following: ● a speedometer (which shows the riding speed) ● a ...

  • Page 23

    Instrument and control functions 3-9 3 clock the clock displays when the key is turned to “on”. In addition, the clock can be displayed for 10 seconds by pushing the “select” button when the main switch is in the “off”, “lock” or “ ” position. To set the clock 1. Turn the key to “on”. 2. Push the “s...

  • Page 24

    Instrument and control functions 3-10 3 fuel meter the fuel meter indicates the amount of fuel in the fuel tank. The display seg- ments of the fuel meter disappear to- wards “e” (empty) as the fuel level decreases. When the last segment on the left starts flashing, refuel as soon as possible. Note: ...

  • Page 25

    Instrument and control functions 3-11 3 ● when the key is turned to “on”, the coolant temperature is auto- matically displayed, even if the air intake temperature was displayed prior to turning the key to “off”. ● when the air intake temperature display is selected, “a” is displayed for one second, ...

  • Page 26

    Instrument and control functions 3-12 3 lcd and tachometer brightness control mode this function allows you to adjust the brightness of the lcd and the tachom- eter panel and needle to suit the out- side lighting conditions. To set the brightness 1. Turn the key to “off”. 2. Push and hold the “selec...

  • Page 27

    Instrument and control functions 3-13 3 eau12347 handlebar switches left right eau12350 pass switch “ ” press this switch to flash the headlight. Eau12400 dimmer switch “ / ” set this switch to “ ” for the high beam and to “ ” for the low beam. Eau12460 turn signal switch “ / ” to signal a right-han...

  • Page 28

    Instrument and control functions 3-14 3 eau44710 the engine trouble warning light and abs warning light (abs model only) will come on when the key is turned to “on” and the start switch is pushed, but this does not indicate a malfunction. Eau12733 hazard switch “ ” with the key in the “on” or “ ” po...

  • Page 29

    Instrument and control functions 3-15 3 eau26822 brake lever the brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the handle- bar grip. The brake lever is equipped with a po- sition adjusting dial. To adjust the dis- tance between the brake lever an...

  • Page 30

    Instrument and control functions 3-16 3 ● this abs has a test mode which allows the owner to experience the pulsating at the brake lever or brake pedal when the abs is oper- ating. However, special tools are required, so please consult your yamaha dealer when performing this test. Eau13072 fuel tank...

  • Page 31

    Instrument and control functions 3-17 3 eau13220 fuel make sure that there is sufficient fuel in the tank. When refueling, be sure to in- sert the pump nozzle into the fuel tank filler hole and to fill the tank to the bot- tom of the filler tube as shown. Warning ewa10880 ● do not overfill the fuel ...

  • Page 32

    Instrument and control functions 3-18 3 eau13412 fuel tank breather hose before operating the motorcycle: ● check the fuel tank breather hose connection. ● check the fuel tank breather hose for cracks or damage, and replace it if damaged. ● make sure that the fuel tank breather hose is not blocked, ...

  • Page 33

    Instrument and control functions 3-19 3 2. Push the rear of the seat down to lock it in place. 3. Remove the key. Note: make sure that the seat is properly se- cured before riding. Eau14281 helmet holder to open the helmet holder, insert the key into the lock, and then turn the key as shown. To lock...

  • Page 34

    Instrument and control functions 3-20 3 ● do not exceed the maximum load of fz6-nahg 191 kg (421 lb) fz6-nhg 196 kg (432 lb) for the vehicle. Eau36462 adjusting the shock absorber assembly this shock absorber assembly is equipped with a spring preload adjust- ing ring. Caution: eca10100 never attemp...

  • Page 35

    Instrument and control functions 3-21 3 the following information before handling the shock absorber. The manufacturer cannot be held re- sponsible for property damage or personal injury that may result from improper handling. ● do not tamper with or attempt to open the gas cylinder. ● do not subjec...

  • Page 36

    Instrument and control functions 3-22 3 eau15312 ignition circuit cut-off system the ignition circuit cut-off system (com- prising the sidestand switch, clutch switch and neutral switch) has the fol- lowing functions. ● it prevents starting when the trans- mission is in gear and the side- stand is u...

  • Page 37

    Instrument and control functions 3-23 3 with the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is turned on. 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? With the engine still runni...

  • Page 38: Pre-Operation Checks

    Pre-operation checks 4-1 4 eau15593 the condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air p...

  • Page 39: Pre-Operation Checks

    Pre-operation checks 4-2 4 eau15605 pre-operation check list item checks page fuel • check fuel level in fuel tank. • refuel if necessary. • check fuel line for leakage. 3-17 engine oil • check oil level in engine. • if necessary, add recommended oil to specified level. • check vehicle for oil leaka...

  • Page 40: Pre-Operation Checks

    Pre-operation checks 4-3 4 throttle grip • make sure that operation is smooth. • check cable free play. • if necessary, have yamaha dealer adjust cable free play and lubricate cable and grip housing. 6-16, 6-25 control cables • make sure that operation is smooth. • lubricate if necessary. 6-24 drive...

  • Page 41

    Operation and important riding points 5-1 5 eau15950 warning ewa10270 ● become thoroughly familiar with all operating controls and their functions before riding. Consult a yamaha dealer re- garding any control or function that you do not thoroughly un- derstand. ● never start the engine or oper- ate...

  • Page 42

    Operation and important riding points 5-2 5 serve the battery. Do not crank the en- gine more than 10 seconds on any one attempt. Caution: eca16040 ● if the oil level warning light flick- ers or remains on after starting, immediately stop the engine, and then check the engine oil level and the vehic...

  • Page 43

    Operation and important riding points 5-3 5 caution: eca10260 ● even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long dis- tances. The transmission is properly lubricated only when the engine is running. ...

  • Page 44

    Operation and important riding points 5-4 5 caution: eca10301 after 1000 km (600 mi) of operation, the engine oil must be changed and the oil filter cartridge or element re- placed. 1600 km (1000 mi) and beyond the vehicle can now be operated nor- mally. Caution: eca10310 ● keep the engine speed out...

  • Page 45

    Periodic maintenance and minor repair 6-1 6 eau17240 safety is an obligation of the owner. Pe- riodic inspection, adjustment and lubri- cation will keep your vehicle in the safest and most efficient condition pos- sible. The most important points of in- spection, adjustment, and lubrication are expl...

  • Page 46

    Periodic maintenance and minor repair 6-2 6 eau1770a periodic maintenance and lubrication chart note: ● the annual checks must be performed every year, except if a kilometer-based maintenance, or for the uk, a mileage-based maintenance, is performed instead. ● from 50000 km (30000 mi), repeat the ma...

  • Page 47

    Periodic maintenance and minor repair 6-3 6 8 * brake hoses • check for cracks or damage. √ √ √ √ √ • replace. Every 4 years 9 * wheels • check runout and for damage. √ √ √ √ 10 * tires • check tread depth and for dam- age. • replace if necessary. • check air pressure. • correct if necessary. √ √ √ ...

  • Page 48

    Periodic maintenance and minor repair 6-4 6 17 brake pedal pivot shaft • lubricate with lithium-soap-based grease. √ √ √ √ √ 18 clutch lever pivot shaft • lubricate with lithium-soap-based grease. √ √ √ √ √ 19 shift pedal pivot shaft • lubricate with lithium-soap-based grease. √ √ √ √ √ 20 sidestand...

  • Page 49

    Periodic maintenance and minor repair 6-5 6 eau18680 note: ● air filter • this model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with com- pressed air to avoid damaging it. • the air filter element needs to be replaced more frequently when riding in...

  • Page 50

    Periodic maintenance and minor repair 6-6 6 eau18751 removing and installing the panel the panel shown needs to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time the panel needs to be removed and installed. Eau33020 panel a to remove the pa...

  • Page 51

    Periodic maintenance and minor repair 6-7 6 before installing a spark plug, the spark plug gap should be measured with a wire thickness gauge and, if necessary, adjusted to specification. Clean the surface of the spark plug gasket and its mating surface, and then wipe off any grime from the spark pl...

  • Page 52

    Periodic maintenance and minor repair 6-8 6 4. Remove the engine oil dipstick and wipe it clean, insert it back into the hole (without screwing it in), and then remove it again to check the oil level. Note: the engine oil should be between the minimum and maximum level marks. 5. If the engine oil is...

  • Page 53

    Periodic maintenance and minor repair 6-9 6 note: an oil filter wrench is available at a yamaha dealer. 5. Apply a thin coat of engine oil to the o-ring of the new oil filter car- tridge. Note: make sure that the o-ring is properly seated. 6. Install the new oil filter cartridge with an oil filter w...

  • Page 54

    Periodic maintenance and minor repair 6-10 6 9. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, im- mediately turn the engine off and check for the cause. Note: after the engine is started, the engine oil level warning light should go ...

  • Page 55

    Periodic maintenance and minor repair 6-11 6 4. Add coolant to the maximum level mark, and then install the reservoir cap. Caution: eca10471 ● if coolant is not available, use distilled water or soft tap water instead. Do not use hard water or salt water since it is harmful to the engine. ● if water...

  • Page 56

    Periodic maintenance and minor repair 6-12 6 6. Drain the coolant from the coolant reservoir by turning it upside down. 7. Install the coolant reservoir and its reservoir cover by placing them in the original position, and then in- stalling the bolts. 8. Remove the coolant drain bolt to drain the co...

  • Page 57

    Periodic maintenance and minor repair 6-13 6 the coolant as soon as possible, otherwise the effectiveness of the coolant will be reduced. 12. Install the coolant reservoir cap. 13. Install the radiator cap, radiator cap retainer and radiator cap re- taining bolt. 14. Start the engine, let it idle fo...

  • Page 58

    Periodic maintenance and minor repair 6-14 6 caution: eca12880 when removing the air filter case cover, be careful not to allow foreign objects to drop into the air intake manifold. 4. Pull the air filter element out. 5. Insert a new air filter element into the air filter case. Caution: eca10480 ● m...

  • Page 59

    Periodic maintenance and minor repair 6-15 6 warning ewa12471 be sure to place the hoses in their original position as shown. 8. Install the seat. Eau34301 adjusting the engine idling speed the engine idling speed must be checked and, if necessary, adjusted as follows at the intervals specified in t...

  • Page 60

    Periodic maintenance and minor repair 6-16 6 eau21382 checking the throttle cable free play the throttle cable free play should mea- sure 3.0–5.0 mm (0.12–0.20 in) at the throttle grip. Periodically check the throttle cable free play and, if neces- sary, have a yamaha dealer adjust it. Eau21401 valv...

  • Page 61

    Periodic maintenance and minor repair 6-17 6 warning ewa11020 because loading has an enormous impact on the handling, braking, performance and safety characteris- tics of your motorcycle, you should keep the following precautions in mind. ● never overload the motorcycle! Operation of an overloaded m...

  • Page 62

    Periodic maintenance and minor repair 6-18 6 warning ewa10470 ● have a yamaha dealer replace excessively worn tires. Besides being illegal, operating the vehi- cle with excessively worn tires decreases riding stability and can lead to loss of control. ● the replacement of all wheel and brake related...

  • Page 63

    Periodic maintenance and minor repair 6-19 6 “broken in”. Therefore, it is ad- visable before doing any high- speed riding to ride conserva- tively for approximately 100 km (60 mi) after installing a new tire. ● the tires must be warmed up before a high-speed run. ● always adjust the tire air pres- ...

  • Page 64

    Periodic maintenance and minor repair 6-20 6 note: if the specified free play cannot be ob- tained as described above or if the clutch does not operate correctly, have a yamaha dealer check the internal clutch mechanism. Eau36501 rear brake light switch the rear brake light switch, which is ac- tiva...

  • Page 65

    Periodic maintenance and minor repair 6-21 6 the point that a wear indicator almost touches the brake disc, have a yamaha dealer replace the brake pads as a set. Eau22500 rear brake pads check each rear brake pad for damage and measure the lining thickness. If a brake pad is damaged or if the lining...

  • Page 66

    Periodic maintenance and minor repair 6-22 6 fluid and may result in vapor lock, and dirt may clog the abs hydrau- lic unit valves. ● brake fluid may deteriorate paint- ed surfaces or plastic parts. Al- ways clean up spilled fluid immediately. ● as the brake pads wear, it is nor- mal for the brake f...

  • Page 67

    Periodic maintenance and minor repair 6-23 6 4. If the drive chain slack is incorrect, adjust it as follows. Eau34311 to adjust the drive chain slack 1. Loosen the axle nut and the lock- nut on each side of the swingarm. 2. To tighten the drive chain, turn the adjusting bolt on each side of the swin...

  • Page 68

    Periodic maintenance and minor repair 6-24 6 eau23022 cleaning and lubricating the drive chain the drive chain must be cleaned and lubricated at the intervals specified in the periodic maintenance and lubrica- tion chart, otherwise it will quickly wear out, especially when riding in dusty or wet are...

  • Page 69

    Periodic maintenance and minor repair 6-25 6 eau23111 checking and lubricating the throttle grip and cable the operation of the throttle grip should be checked before each ride. In addi- tion, the cable should be lubricated at the intervals specified in the periodic maintenance chart. Eau44270 check...

  • Page 70

    Periodic maintenance and minor repair 6-26 6 eau23141 checking and lubricating the brake and clutch levers brake lever clutch lever the operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lu- bricated if necessary. Eau23200 checking and lubrica...

  • Page 71

    Periodic maintenance and minor repair 6-27 6 eaum1650 lubricating the swingarm piv- ots the swingarm pivots must be lubricat- ed at the intervals specified in the peri- odic maintenance and lubrication chart. Eau23271 checking the front fork the condition and operation of the front fork must be chec...

  • Page 72

    Periodic maintenance and minor repair 6-28 6 eau23280 checking the steering worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as fol- lows at the intervals specified in the pe- riodic maintenance and lubrication chart. 1. Place a stand under t...

  • Page 73

    Periodic maintenance and minor repair 6-29 6 eau34372 battery fz6-nhg fz6-nahg the battery is located under the fuel tank. (see page 6-13.) this model is equipped with a sealed- type (mf) battery, which does not re- quire any maintenance. There is no need to check the electrolyte or to add distilled...

  • Page 74

    Periodic maintenance and minor repair 6-30 6 4. After installation, make sure that the battery leads are properly con- nected to the battery terminals. Caution: eca10630 ● always keep the battery charged. Storing a discharged battery can cause permanent battery damage. ● to charge a sealed-type (mf)...

  • Page 75

    Periodic maintenance and minor repair 6-31 6 if a fuse is blown, replace it as follows. 1. Turn the key to “off” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. Caution: eca10640 do not use a fuse of a higher amper- ag...

  • Page 76

    Periodic maintenance and minor repair 6-32 6 eau34380 replacing the headlight bulb this model is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Remove the headlight unit by re- moving the bolts on each side. 2. Disconnect the headlight coupler, and ...

  • Page 77

    Periodic maintenance and minor repair 6-33 6 5. Install the headlight bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the bolts. 7. Have a yamaha dealer adjust the headlight beam if necessary. Eau32822 replacing the tail/brake light bulb 1. Remove the seat. (s...

  • Page 78

    Periodic maintenance and minor repair 6-34 6 eau24202 replacing a turn signal light bulb 1. Remove the turn signal light lens by removing the screw. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 3. Insert a new bulb into the socket, push it in, and then turn it clo...

  • Page 79

    Periodic maintenance and minor repair 6-35 6 eau34403 replacing the auxiliary light bulb if the auxiliary light bulb burns out, re- place it as follows. 1. Remove the headlight unit by re- moving the bolts on each side. 2. Remove the auxiliary light socket (together with the bulb) by turning it coun...

  • Page 80

    Periodic maintenance and minor repair 6-36 6 eau44790 front wheel (fz6-nhg) warning ewa14840 for the abs model, have a yamaha dealer remove and install the wheel. Eau24490 to remove the front wheel warning ewa10820 ● it is advisable to have a yamaha dealer service the wheel. ● securely support the m...

  • Page 81

    Periodic maintenance and minor repair 6-37 6 6. Push down hard on the handlebar several times to check for proper fork operation. Eau44800 rear wheel (fz6-nhg) warning ewa14840 for the abs model, have a yamaha dealer remove and install the wheel. Eau43380 to remove the rear wheel warning ewa10820 ● ...

  • Page 82

    Periodic maintenance and minor repair 6-38 6 note: a rubber mallet may be useful to tap the wheel axle out. 6. Push the wheel forward, and then remove the drive chain from the rear sprocket. Note: the drive chain does not need to be disassembled in order to remove and install the rear wheel. 7. Remo...

  • Page 83

    Periodic maintenance and minor repair 6-39 6 eau25870 troubleshooting although yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur dur- ing operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and ...

  • Page 84

    Periodic maintenance and minor repair 6-40 6 eau42360 troubleshooting charts starting problems or poor engine performance warning ewa10840 keep away open flames and do not smoke while checking or working on the fuel system. Check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There i...

  • Page 85

    Periodic maintenance and minor repair 6-41 6 engine overheating warning ewa10400 ● do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled. ● after...

  • Page 86: Motorcycle Care And Storage

    Motorcycle care and storage 7-1 7 eau37833 matte color caution caution: eca15192 some models are equipped with matte colored finished parts. Be sure to consult a yamaha dealer for advice on what products to use be- fore cleaning the vehicle. Using a brush, harsh chemical products or cleaning compoun...

  • Page 87: Motorcycle Care and Storage

    Motorcycle care and storage 7-2 7 contact with strong or abrasive cleaning products, solvent or thinner, fuel (gasoline), rust re- movers or inhibitors, brake flu- id, antifreeze or electrolyte. ● do not use high-pressure wash- ers or steam-jet cleaners since they cause water seepage and deteriorati...

  • Page 88: Motorcycle Care And Storage

    Motorcycle care and storage 7-3 7 4. To prevent corrosion, it is recom- mended to apply a corrosion pro- tection spray on all metal, including chrome- and nickel-plat- ed, surfaces. 5. Use spray oil as a universal clean- er to remove any remaining dirt. 6. Touch up minor paint damage caused by stone...

  • Page 89: Motorcycle Care and Storage

    Motorcycle care and storage 7-4 7 3. Perform the following steps to pro- tect the cylinders, piston rings, etc. From corrosion. A. Remove the spark plug caps and spark plugs. B. Pour a teaspoonful of engine oil into each spark plug bore. C. Install the spark plug caps onto the spark plugs, and then ...

  • Page 90: Specifications

    Specifications 8-1 8 dimensions: overall length: 2095 mm (82.5 in) overall width: 755 mm (29.7 in) overall height: 1085 mm (42.7 in) seat height: 795 mm (31.3 in) wheelbase: 1440 mm (56.7 in) ground clearance: 145 mm (5.71 in) minimum turning radius: 2800 mm (110.2 in) weight: with oil and fuel: fz6...

  • Page 91: Specifications

    Specifications 8-2 8 gear ratio: 1st: 37/13 (2.846) 2nd: 37/19 (1.947) 3rd: 28/18 (1.556) 4th: 32/24 (1.333) 5th: 25/21 (1.190) 6th: 26/24 (1.083) chassis: frame type: diamond caster angle: 25.00 ° trail: 97.5 mm (3.84 in) front tire: type: tubeless size: 120/70 zr17m/c (58w) manufacturer/model: bri...

  • Page 92: Specifications

    Specifications 8-3 8 wheel travel: 130.0 mm (5.12 in) electrical system: ignition system: transistorized coil ignition (digital) charging system: ac magneto battery: model: gt12b-4 voltage, capacity: 12 v, 10.0 ah headlight: bulb type: halogen bulb bulb voltage, wattage × quantity: headlight: 12 v, ...

  • Page 93: Consumer Information

    Consumer information 9-1 9 eau26351 identification numbers record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the vehi- cle is stolen. ...

  • Page 94: Consumer Information

    Consumer information 9-2 9 eau26540 model label the model label is affixed to the frame under the seat. (see page 3-18.) record the information on this label in the space provided. This information will be needed when ordering spare parts from a yamaha dealer. 1. Model label u5s5e1e0.Book page 2 fri...

  • Page 95: Index

    Index a abs (for abs models) .......................... 3-15 abs warning light (for abs models)....... 3-7 air filter element, replacing ................... 6-13 anti-theft alarm (optional) ..................... 3-12 auxiliary light bulb, replacing ................ 6-35 b battery ......................

  • Page 96: Index

    Index troubleshooting .................................... 6-39 troubleshooting charts ......................... 6-40 turn signal indicator lights ...................... 3-4 turn signal light bulb, replacing ............ 6-34 turn signal switch ................................. 3-13 v valve clearanc...

  • Page 97

    U5s5e1e0.Book page 3 friday, june 22, 2007 1:03 pm.

  • Page 98

    Printed on recycled paper yamaha motor co., ltd. Printed in japan 2007.07-0.3 ×1 cr (e).