1. DL manuals
  2. Yamaha
  3. Motorcycle
  4. FZS10Z
  5. Owner's Manual

Yamaha FZS10Z Owner's Manual

Summary of FZS10Z

  • Page 1

    Dic183 1ca-28199-10 fzs10z(c) owner’s manual read this manual carefully before operating this vehicle. Lit-11626-23-58.

  • Page 2

    Eau10042 read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold. U1ca10e0.Book page 1 tuesday, november 24, 2009 1:41 pm.

  • Page 3

    Introduction eau10083 congratulations on your purchase of the yamaha fzs10z(c). This model is the result of yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made yamaha a le...

  • Page 4

    Important manual information eau10132 particularly important information is distinguished in this manual by the following notations: this is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injur...

  • Page 5

    Important manual information eau10193 fzs10z(c) owner’s manual ©2009 by yamaha motor corporation, u.S.A. 1st edition, november 2009 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor corporation, u.S.A. Is expressly prohibited. Printed in japan. P/...

  • Page 6

    Table of contents location of important labels .............................................1-1 safety information ..................2-1 description ..................................3-1 left view ..........................................3-1 right view ........................................3-2 co...

  • Page 7

    Table of contents replacing the tail/brake light bulb ...........................................7-34 replacing a turn signal light bulb ...........................................7-34 replacing the license plate light bulb ...........................................7-35 front wheel ...................

  • Page 8

    Location of important labels 1-1 1 eau10384 read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is av...

  • Page 9

    Location of important labels 1-2 1 notice cleaning with alkaline or acid cleaner, gasoline or solvent will damage windshield. Use neutral detergent. 4b5-2815k-00 tire information cold tire normal pressure should be set as follows. • up to 90 kg (198 lbs) load front rear : 250 kpa, (2.50 kgf/cm²), 36...

  • Page 10

    Location of important labels 1-3 1 1 u1ca10e0.Book page 3 tuesday, november 24, 2009 1:41 pm.

  • Page 11

    Location of important labels 1-4 1 1 california only u1ca10e0.Book page 4 tuesday, november 24, 2009 1:41 pm.

  • Page 12

    2-1 2 safety information eau10283 be a responsible owner as the vehicle’s owner, you are respon- sible for the safe and proper operation of your motorcycle. Motorcycles are single-track vehicles. Their safe use and operation are de- pendent upon the use of proper riding techniques as well as the exp...

  • Page 13

    Safety information 2-2 2 due to excessive speed or under- cornering (insufficient lean angle for the speed). • always obey the speed limit and never travel faster than warrant- ed by road and traffic conditions. • always signal before turning or changing lanes. Make sure that other motorists can see...

  • Page 14

    Safety information 2-3 2 ● do not run engine in poorly venti- lated or partially enclosed areas such as barns, garages, or car- ports. ● do not run engine outdoors where engine exhaust can be drawn into a building through openings such as windows and doors. Loading adding accessories or cargo to you...

  • Page 15

    Safety information 2-4 2 modifications not specifically recom- mended by yamaha, even if sold and installed by a yamaha dealer. Aftermarket parts, accessories, and modifications while you may find aftermarket prod- ucts similar in design and quality to genuine yamaha accessories, recog- nize that so...

  • Page 16

    Description 3-1 3 eau10410 left view 1. Front fork spring preload adjusting bolt (page 4-17) 2. Front fork compression damping force adjusting screw (page 4-17) 3. Air filter element (page 7-15) 4. Main fuse (page 7-32) 5. Fuel injection system fuse (page 7-32) 6. Storage compartment (page 4-16) 7. ...

  • Page 17

    Description 3-2 3 eau10420 right view 1 2 3 4 5 6 7 8 9 10 11 12 1. Owner’s tool kit (page 7-2) 2. Rider seat lock lever (page 4-15) 3. Fuse box (page 7-32) 4. Battery (page 7-30) 5. Rear brake fluid reservoir (page 7-23) 6. Engine oil filler cap (page 7-11) 7. Front fork rebound damping force adjus...

  • Page 18

    Description 3-3 3 eau10430 controls and instruments 1 2 3 4 6 7 8 5 1. Clutch lever (page 4-10) 2. Left handlebar switches (page 4-9) 3. Main switch/steering lock (page 4-1) 4. Multi-function meter unit (page 4-5) 5. Front brake fluid reservoir (page 7-23) 6. Right handlebar switches (page 4-9) 7. T...

  • Page 19

    Instrument and control functions 4-1 4 eau10460 main switch/steering lock the main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. Eau26900 on all electrical circuits are supplied with power, and the meter ...

  • Page 20

    Instrument and control functions 4-2 4 to unlock the steering push the key in, and then turn it to “off” while still pushing it. Eau11004 indicator and warning lights eau11030 turn signal indicator lights “ ” and “ ” the corresponding indicator light flash- es when the turn signal switch is pushed t...

  • Page 21

    Instrument and control functions 4-3 4 circuit, the following cycle will be repeated until the malfunction is corrected: the oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a yamaha dealer check the vehicle. Eau11427 coolant temperature warning light “...

  • Page 22

    Instrument and control functions 4-4 4 coolant temperature display conditions what to do under 39 °c (under 103 °f) message “lo” is displayed. Ok. Go ahead with riding. 40–116 °c (104–242 °f) temperature is displayed. Ok. Go ahead with riding. 117–134 °c (243–274 °f) temperature display flashes. War...

  • Page 23

    Instrument and control functions 4-5 4 eau11534 engine trouble warning light “ ” this warning light comes on or flashes if a problem is detected in the electrical circuit monitoring the engine. If this oc- curs, have a yamaha dealer check the self-diagnosis system. (see page 4-8 for an explanation o...

  • Page 24

    Instrument and control functions 4-6 4 tachometer the electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range. When the key is turned to “on”, the ta- chometer needle will sweep once across the r/min range and then return to zero r/min in order to te...

  • Page 25

    Instrument and control functions 4-7 4 mode “f-trip” and start counting the distance traveled from that point. In that case, push the “select” button to switch the display between the various tripmeter and odometer modes in the following order: f-trip → trip a → trip b → odo → f-trip to reset a trip...

  • Page 26

    Instrument and control functions 4-8 4 air intake temperature mode the air intake temperature display indi- cates the temperature of the air drawn into the air filter case. Turn the key to “on”, and push the “reset” button to switch the coolant temperature display to the air intake temperature displ...

  • Page 27

    Instrument and control functions 4-9 4 this function allows you to adjust the brightness of the lcd and the tachom- eter panel and needle to suit the out- side lighting conditions. To set the brightness 1. Turn the key to “off”. 2. Push and hold the “select” but- ton. 3. Turn the key to “on”, and th...

  • Page 28

    Instrument and control functions 4-10 4 eau12711 start switch “ ” push this switch to crank the engine with the starter. See page 6-1 for start- ing instructions prior to starting the en- gine. Eau41700 the engine trouble warning light will come on when the key is turned to “on” and the start switch...

  • Page 29

    Instrument and control functions 4-11 4 eau26823 brake lever the brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the handle- bar grip. The brake lever is equipped with a brake lever position adjusting dial. To adjust the distance between the brake ...

  • Page 30

    Instrument and control functions 4-12 4 tip the fuel tank cap cannot be closed un- less the key is in the lock. In addition, the key cannot be removed if the cap is not properly closed and locked. Warning ewa11091 make sure that the fuel tank cap is properly closed after filling fuel. Leaking fuel i...

  • Page 31

    Instrument and control functions 4-13 4 ately. If gasoline spills on your skin, wash with soap and water. If gaso- line spills on your clothing, change your clothes. Eau13301 notice eca11400 use only unleaded gasoline. The use of leaded gasoline will cause severe damage to internal engine parts, suc...

  • Page 32

    Instrument and control functions 4-14 4 ● make sure that the end of the fuel tank breather/overflow hose is po- sitioned inside of the clamp. Eau13445 catalytic converters this vehicle is equipped with catalytic converters in the exhaust system. Warning ewa10862 the exhaust system is hot after op- e...

  • Page 33

    Instrument and control functions 4-15 4 eau39322 seats passenger seat to remove the passenger seat 1. Insert the key into the seat lock, and then turn it counterclockwise. 2. Pull the passenger seat forward, and then lift it up. To install the passenger seat 1. Place the passenger seat in the origin...

  • Page 34

    Instrument and control functions 4-16 4 tip make sure that the seats are properly secured before riding. Eau14462 storage compartment the storage compartment is located under the passenger seat. (see page 4-15.) warning ewa10961 ● do not exceed the load limit of 3 kg (7 lb) for the storage com- part...

  • Page 35

    Instrument and control functions 4-17 4 eau39333 adjusting the front fork warning ewa14670 always adjust the spring preload on both fork legs equally, otherwise poor handling and loss of stability may result. Each front fork leg is equipped with a spring preload adjusting bolt, the right front fork ...

  • Page 36

    Instrument and control functions 4-18 4 rebound damping force the rebound damping force is adjusted on the right front fork leg only. To in- crease the rebound damping force and thereby harden the rebound damping, turn the adjusting screw in direction (a). To decrease the rebound damping force and t...

  • Page 37

    Instrument and control functions 4-19 4 eau39344 adjusting the shock absorber assembly this shock absorber assembly is equipped with a spring preload adjust- ing ring and a rebound damping force adjusting screw. Notice eca10101 to avoid damaging the mechanism, do not attempt to turn beyond the maxim...

  • Page 38

    Instrument and control functions 4-20 4 tip to obtain a precise adjustment, it is ad- visable to check the actual total number of clicks or turns of the damping force adjusting mechanism. This adjustment range may not exactly match the spec- ifications listed due to small differences in production. ...

  • Page 39

    Instrument and control functions 4-21 4 eau41941 exup system this model is equipped with yamaha’s exup (exhaust ultimate power valve) system. This system boosts engine power by means of a valve that regu- lates the inner diameter of the exhaust pipe. The exup system valve is con- stantly adjusted in...

  • Page 40

    Instrument and control functions 4-22 4 eau44902 ignition circuit cut-off system the ignition circuit cut-off system (com- prising the sidestand switch, clutch switch and neutral switch) has the fol- lowing functions. ● it prevents starting when the trans- mission is in gear and the side- stand is u...

  • Page 41

    Instrument and control functions 4-23 4 with the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is set to “ 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? With the engine still running...

  • Page 42

    For your safety – pre-operation checks 5-1 5 eau15596 inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the owner’s manual. Warning ewa11151 failure to inspect or maint...

  • Page 43

    For your safety – pre-operation checks 5-2 5 rear brake • check operation. • if soft or spongy, have yamaha dealer bleed hydraulic system. • check brake pads for wear. • replace if necessary. • check fluid level in reservoir. • if necessary, add recommended brake fluid to specified level. • check hy...

  • Page 44

    For your safety – pre-operation checks 5-3 5 chassis fasteners • make sure that all nuts, bolts and screws are properly tightened. • tighten if necessary. — instruments, lights, signals and switches • check operation. • correct if necessary. — sidestand switch • check operation of ignition circuit c...

  • Page 45

    Operation and important riding points 6-1 6 eau15951 read the owner’s manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your yamaha dealer. Warning ewa10271 failure to familiarize yourself with the controls can lead to loss of con- tr...

  • Page 46

    Operation and important riding points 6-2 6 2. Shift the transmission into the neu- tral position. (see page 6-2.) the neutral indicator light should come on. If not, ask a yamaha dealer to check the electrical circuit. 3. Start the engine by pushing the start switch. Notice: for maxi- mum engine li...

  • Page 47

    Operation and important riding points 6-3 6 4. At the recommended shift points shown in the following table, close the throttle, and at the same time, quickly pull the clutch lever in. 5. Shift the transmission into second gear. (make sure not to shift the transmission into the neutral posi- tion.) ...

  • Page 48

    Operation and important riding points 6-4 6 1600 km (1000 mi) and beyond the vehicle can now be operated nor- mally. Notice eca10310 ● keep the engine speed out of the tachometer red zone. ● if any engine trouble should oc- cur during the engine break-in period, immediately have a yamaha dealer chec...

  • Page 49

    Periodic maintenance and adjustment 7-1 7 eau17232 periodic inspection, adjustment, and lu- brication will keep your vehicle in the safest and most efficient condition pos- sible. Safety is an obligation of the vehi- cle owner/operator. The most important points of vehicle inspection, adjust- ment, ...

  • Page 50

    Periodic maintenance and adjustment 7-2 7 eau17491 owner’s tool kit the owner’s tool kit is located inside the storage compartment under the pas- senger seat. (see page 4-15.) the service information included in this manual and the tools provided in the owner’s tool kit are intended to assist you in...

  • Page 51

    Periodic maintenance and adjustment 7-3 7 eau48490 tip ● from 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months. ● items marked with an asterisk require special tools, data and technical skills, have a yamaha dealer perform the service. ...

  • Page 52

    Periodic maintenance and adjustment 7-4 7 7 * evaporative emis- sion control system (for california only) • check control system for dam- age. • replace if necessary. √ 8 * air induction sys- tem • check the air cut-off valve, reed valve, and hose for damage. • replace any damaged parts. √ √ no. Ite...

  • Page 53

    Periodic maintenance and adjustment 7-5 7 eau32186 general maintenance and lubrication chart no. Item routine initial odometer readings 600 mi (1000 km) or 1 month 4000 mi (7000 km) or 6 months 8000 mi (13000 km) or 12 months 12000 mi (19000 km) or 18 months 16000 mi (25000 km) or 24 months 20000 mi...

  • Page 54

    Periodic maintenance and adjustment 7-6 7 10 drive chain • check chain slack, alignment and condition. • adjust and lubricate chain with a special o-ring chain lubricant thoroughly. Every 600 mi (1000 km) and after washing the motorcycle, riding in the rain or riding in wet areas 11 * steering beari...

  • Page 55

    Periodic maintenance and adjustment 7-7 7 19 * front fork • check operation and for oil leak- age. • replace if necessary. √ √ √ √ √ 20 * shock absorber as- sembly • check operation and for oil leak- age. • replace if necessary. √ √ √ √ √ 21 * rear suspension link pivots • check operation. • correct...

  • Page 56

    Periodic maintenance and adjustment 7-8 7 eau17650 tip ● air filter • this model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with com- pressed air to avoid damaging it. • the air filter element needs to be replaced more frequently when riding in unu...

  • Page 57

    Periodic maintenance and adjustment 7-9 7 eau18771 removing and installing pan- els the panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed. Eau40030 panels a and b to remove one ...

  • Page 58

    Periodic maintenance and adjustment 7-10 7 to install the panel place the panel in the original position, and then install the screw. Eau19652 checking the spark plugs the spark plugs are important engine components, which should be checked periodically, preferably by a yamaha dealer. Since heat and...

  • Page 59

    Periodic maintenance and adjustment 7-11 7 tip if a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4–1/2 turn past finger tight. However, the spark plug should be tightened to the speci- fied torque as soon as possible. Notice eca10840 do not ...

  • Page 60

    Periodic maintenance and adjustment 7-12 7 4. If the engine oil is below the mini- mum level mark, add sufficient oil of the recommended type to raise it to the correct level. To change the engine oil (with or without oil filter cartridge replace- ment) 1. Place the vehicle on a level sur- face. 2. ...

  • Page 61

    Periodic maintenance and adjustment 7-13 7 tip make sure that the o-ring is properly seated. 7. Install the new oil filter cartridge with an oil filter wrench, and then tighten it to the specified torque with a torque wrench. 8. Install the engine oil drain bolt and its new gasket, and then tighten ...

  • Page 62

    Periodic maintenance and adjustment 7-14 7 10. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, im- mediately turn the engine off and check for the cause. Tip after the engine is started, the engine oil level warning light should go off...

  • Page 63

    Periodic maintenance and adjustment 7-15 7 if water has been used instead of coolant, replace it with cool- ant as soon as possible, other- wise the cooling system will not be protected against frost and corrosion. If water has been added to the coolant, have a yamaha dealer check the anti- freeze c...

  • Page 64

    Periodic maintenance and adjustment 7-16 7 5. Lift the front of the fuel tank, and carefully tilt it back and away from the air filter case, but do not dis- connect the fuel hoses. Warning! Make sure that the fuel tank is well supported. Do not tilt or pull the fuel tank too much, otherwise the fuel...

  • Page 65

    Periodic maintenance and adjustment 7-17 7 hose and the fuel tank overflow hose in the original position. Warning! Before placing the fuel tank in the original position, make sure that the fuel hoses are not damaged. If any fuel hose is damaged, do not start the engine but have a yamaha dealer repla...

  • Page 66

    Periodic maintenance and adjustment 7-18 7 eau21383 checking the throttle cable free play the throttle cable free play should mea- sure 3.0–5.0 mm (0.12–0.20 in) at the inner edge of the throttle grip. Periodi- cally check the throttle cable free play and, if necessary, have a yamaha deal- er adjust...

  • Page 67

    Periodic maintenance and adjustment 7-19 7 warning ewa10511 never overload your vehicle. Opera- tion of an overloaded vehicle could cause an accident. Tire inspection always check the tires before operating the motorcycle. If a tire tread shows crosswise lines (minimum tread depth), if the tire has ...

  • Page 68

    Periodic maintenance and adjustment 7-20 7 this motorcycle is equipped with cast wheels and tubeless tires with valves. Warning ewa10481 ● the front and rear tires should be of the same make and de- sign, otherwise the handling characteristics of the motorcy- cle may be different, which could lead t...

  • Page 69

    Periodic maintenance and adjustment 7-21 7 eau21960 cast wheels to maximize the performance, durabil- ity, and safe operation of your vehicle, note the following points regarding the specified wheels. ● the wheel rims should be checked for cracks, bends or warpage be- fore each ride. If any damage i...

  • Page 70

    Periodic maintenance and adjustment 7-22 7 eau37913 checking the brake lever free play there should be no free play at the brake lever end. If there is free play, have a yamaha dealer inspect the brake system. Warning ewa14211 a soft or spongy feeling in the brake lever can indicate the presence of ...

  • Page 71

    Periodic maintenance and adjustment 7-23 7 eau22392 checking the front and rear brake pads the front and rear brake pads must be checked for wear at the intervals spec- ified in the periodic maintenance and lubrication chart. Eau36890 front brake pads each front brake pad is provided with wear indic...

  • Page 72

    Periodic maintenance and adjustment 7-24 7 before riding, check that the brake fluid is above the minimum level mark and replenish if necessary. A low brake fluid level may indicate worn brake pads and/or brake system leakage. If the brake fluid level is low, be sure to check the brake pads for wear...

  • Page 73

    Periodic maintenance and adjustment 7-25 7 eau22760 drive chain slack the drive chain slack should be checked before each ride and adjusted if necessary. Eau22793 to check the drive chain slack 1. Place the motorcycle on the cen- terstand. 2. Shift the transmission into the neu- tral position. 3. Sp...

  • Page 74

    Periodic maintenance and adjustment 7-26 7 eau23025 cleaning and lubricating the drive chain the drive chain must be cleaned and lubricated at the intervals specified in the periodic maintenance and lubrica- tion chart, otherwise it will quickly wear out, especially when riding in dusty or wet areas...

  • Page 75

    Periodic maintenance and adjustment 7-27 7 eau23112 checking and lubricating the throttle grip and cable the operation of the throttle grip should be checked before each ride. In addi- tion, the cable should be lubricated by a yamaha dealer at the intervals speci- fied in the periodic maintenance ch...

  • Page 76

    Periodic maintenance and adjustment 7-28 7 eau23142 checking and lubricating the brake and clutch levers brake lever clutch lever the operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lu- bricated if necessary. Eau23213 checking and lubricati...

  • Page 77

    Periodic maintenance and adjustment 7-29 7 eau23272 checking the front fork the condition and operation of the front fork must be checked as follows at the intervals specified in the periodic main- tenance and lubrication chart. To check the condition check the inner tubes for scratches, damage and ...

  • Page 78

    Periodic maintenance and adjustment 7-30 7 eau45511 checking the steering worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as fol- lows at the intervals specified in the pe- riodic maintenance and lubrication chart. 1. Place the vehicle on th...

  • Page 79

    Periodic maintenance and adjustment 7-31 7 working near batteries. In case of contact, administer the fol- lowing first aid. • external: flush with plenty of water. • internal: drink large quan- tities of water or milk and im- mediately call a physician. • eyes: flush with water for 15 minutes and s...

  • Page 80

    Periodic maintenance and adjustment 7-32 7 eau43011 replacing the fuses the main fuse, the fuel injection system fuse, and the fuse box, which contains the fuses for the individual circuits, are located under the rider seat. (see page 4-15.) if a fuse is blown, replace it as follows. Tip include ste...

  • Page 81

    Periodic maintenance and adjustment 7-33 7 avoid causing extensive dam- age to the electrical system and possibly a fire. [ewa15131] 4. Turn the key to “on” and turn on the electrical circuit in question to check if the device operates. 5. If the fuse immediately blows again, have a yamaha dealer ch...

  • Page 82

    Periodic maintenance and adjustment 7-34 7 3. Place a new headlight bulb into po- sition, and then secure it with the bulb holder. 4. Install the headlight bulb cover, and then connect the coupler. 5. Have a yamaha dealer adjust the headlight beam if necessary. Eau24114 replacing the tail/brake ligh...

  • Page 83

    Periodic maintenance and adjustment 7-35 7 3. Remove the burnt-out bulb by pull- ing it out. 4. Insert a new bulb into the socket. 5. Install the socket (together with the bulb) by turning it clockwise. 6. Install the turn signal light unit by installing the screw. Notice: do not overtighten the scr...

  • Page 84

    Periodic maintenance and adjustment 7-36 7 3. Remove the burnt-out bulb by pull- ing it out. 4. Insert a new bulb into the socket. 5. Install the socket (together with the bulb) by pushing it in. 6. Install the license plate light unit by installing the screws. Eau24360 front wheel eau40201 to remov...

  • Page 85

    Periodic maintenance and adjustment 7-37 7 eau40211 to install the front wheel 1. Lift the wheel up between the fork legs. 2. Insert the wheel axle. 3. Install the brake caliper (together with the reflector) on each side by installing the bolts. Tip make sure that there is enough space between the b...

  • Page 86

    Periodic maintenance and adjustment 7-38 7 5. Turn the drive chain slack adjust- ing bolts fully in direction (a) and push the wheel forward. 6. Remove the drive chain from the rear sprocket. Tip ● if the drive chain is difficult to re- move, remove the wheel axle first, and then lift the wheel upwa...

  • Page 87

    Periodic maintenance and adjustment 7-39 7 eau25871 troubleshooting although yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur dur- ing operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and lo...

  • Page 88

    Periodic maintenance and adjustment 7-40 7 eau42501 troubleshooting charts starting problems or poor engine performance check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There is no fuel. Check the compression. Supply fuel. The engine does not start. Check the compression. Operate...

  • Page 89

    Periodic maintenance and adjustment 7-41 7 engine overheating warning ewat1040 ● do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled. ● place a...

  • Page 90

    Motorcycle care and storage 8-1 8 eau37833 matte color caution notice eca15192 some models are equipped with matte colored finished parts. Be sure to consult a yamaha dealer for advice on what products to use be- fore cleaning the vehicle. Using a brush, harsh chemical products or cleaning compounds...

  • Page 91

    Motorcycle care and storage 8-2 8 off any detergent residue using plenty of water, as it is harmful to plastic parts. ● do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products, solvent or t...

  • Page 92

    Motorcycle care and storage 8-3 8 4. To prevent corrosion, it is recom- mended to apply a corrosion pro- tection spray on all metal, including chrome- and nickel-plat- ed, surfaces. 5. Use spray oil as a universal clean- er to remove any remaining dirt. 6. Touch up minor paint damage caused by stone...

  • Page 93

    Motorcycle care and storage 8-4 8 3. Perform the following steps to pro- tect the cylinders, piston rings, etc. From corrosion. A. Remove the spark plug caps and spark plugs. B. Pour a teaspoonful of engine oil into each spark plug bore. C. Install the spark plug caps onto the spark plugs, and then ...

  • Page 94

    Specifications 9-1 9 dimensions: overall length: 2140 mm (84.3 in) overall width: 770 mm (30.3 in) overall height: 1205 mm (47.4 in) seat height: 815 mm (32.1 in) wheelbase: 1460 mm (57.5 in) ground clearance: 135 mm (5.31 in) minimum turning radius: 3000 mm (118.1 in) weight: with oil and fuel: fzs...

  • Page 95

    Specifications 9-2 9 gear ratio: 1st: 38/15 (2.533) 2nd: 33/16 (2.063) 3rd: 37/21 (1.762) 4th: 35/23 (1.522) 5th: 27/20 (1.350) 6th: 29/24 (1.208) chassis: frame type: diamond caster angle: 25.00 ° trail: 109.0 mm (4.29 in) front tire: type: tubeless size: 120/70 zr17m/c (58w) manufacturer/model: du...

  • Page 96

    Specifications 9-3 9 charging system: ac magneto battery: model: ytz14s voltage, capacity: 12 v, 11.2 ah headlight: bulb type: halogen bulb bulb voltage, wattage × quantity: headlight: 12 v, 60 w/55 w × 2 tail/brake light: 12 v, 5.0 w/21.0 w × 1 front turn signal/position light: 12 v, 21 w/5.0 w × 2...

  • Page 97

    Consumer information 10-1 10 eau26352 identification numbers record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the vehi- cle is stolen...

  • Page 98

    Consumer information 10-2 10 eau26470 model label the model label is affixed to the frame under the rider seat. (see page 4-15.) record the information on this label in the space provided. This information will be needed when ordering spare parts from a yamaha dealer. Eau48270 vehicle emission contr...

  • Page 99

    Consumer information 10-3 10 eau26551 reporting safety defects if you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the national highway traffic safety administration (nhtsa) in addition to notifying yamaha motor corpor...

  • Page 100

    Consumer information 10-4 10 eau26560 motorcycle noise regulation tampering with noise control system prohibited: federal law prohibits the following acts or the causing thereof: (1) the removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement of ...

  • Page 101

    Consumer information 10-5 10 eau26632 maintenance record copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder t...

  • Page 102

    Consumer information 10-6 10 36000 mi (55000 km) or 54 months 40000 mi (61000 km) or 60 months maintenance interval date of service mileage servicing dealer name and address remarks u1ca10e0.Book page 6 tuesday, november 24, 2009 1:41 pm.

  • Page 103

    Consumer information 10-7 10 eau26663 yamaha motor corporation, u.S.A. Street and enduro motorcycle limited warranty a) b) c) d) e) f) 1. 2. Yamaha motor corporation, u.S.A. Hereby warrants that new yamaha motorcycles will be free from defects in material and workmanship for the period of time state...

  • Page 104

    Consumer information 10-8 10 warranty questions and answers what costs are my responsibility during the warranty period? The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, spark plu...

  • Page 105

    Consumer information 10-9 10 eau26750 yamaha extended service (y.E.S.) keep your yamaha protected even after your warranty expires with genuine yamaha extended service (y.E.S.). Y.E.S. Is designed and administered by yamaha motor corporation to provide maximum owner satisfaction. You get uninterrupt...

  • Page 106

    Consumer information 10-10 10 we urge you to act now. You’ll get the excellent benefits of trip coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your yamaha limited warranty expires. A special note: if visiting your dealer isn’t convenient, co...

  • Page 107

    Index a air filter element, replacing ................... 7-15 b battery .................................................. 7-30 brake and clutch levers, checking and lubricating ........................................... 7-28 brake and shift pedals, checking and lubricating ..........................

  • Page 108

    Index turn signal light bulb, replacing ............ 7-34 turn signal switch ................................... 4-9 v valve clearance .................................... 7-18 vehicle emission control information label .................................................... 10-2 vehicle identification...

  • Page 109

    U1ca10e0.Book page 3 tuesday, november 24, 2009 1:41 pm.

  • Page 110

    Printed in japan 2009.12-0.3 × 1 cr (e) printed on recycled paper yamaha motor co., ltd. Dic183.