1. DL manuals
  2. Yamaha
  3. Boat
  4. GP1300R WaveRunner 2006
  5. Owner's/operator's Manual

Yamaha GP1300R WaveRunner 2006 Owner's/operator's Manual

Summary of GP1300R WaveRunner 2006

  • Page 1

    2006 waverunner gp1300r owner’s/operator’s manual lit-18626-06-51 u.S.A. Edition read this manual carefully before operation!.

  • Page 3: To The Owner/operator

    E eju09890 to the owner/operator thank you for choosing a yamaha water- craft. This owner’s/operator’s manual contains information you will need for proper opera- tion, maintenance, and care. A thorough understanding of these simple instructions will help you to obtain maximum enjoyment from your ne...

  • Page 4: Contents

    E eju09920 contents read this owner’s/operator’s manual carefully before operating your watercraft. General and safety information 1 features and functions 2 operation 3 maintenance and care 4 troubleshooting and emergency procedures 5 appendix 6 e_f1g10.Book page 3 tuesday, july 12, 2005 10:26 am.

  • Page 5: General and

    E 1 eju09930 general and safety information identification numbers ............................1-1 primary identification (pri-id) number ...................................................1-1 hull identification number (hin) ............1-2 engine serial number .............................1-2 emis...

  • Page 6: Identification Numbers

    1-1 e eju18300 identification numbers record the primary identification (pri-id) number, hull identification number (hin) and engine serial number in the spaces pro- vided for assistance when ordering spare parts from a yamaha dealer. Also record and keep these id numbers in a separate place in case...

  • Page 7: Hull Identification Number

    1-2 e eju18841 hull identification number (hin) the hin is stamped on a plate 1 attached to the hull on the aft, starboard (right) side. Eju09971 engine serial number the engine serial number is stamped on a label 1 attached to the engine unit. E_f1g10.Book page 2 tuesday, july 12, 2005 10:26 am.

  • Page 8: Emission Control

    1-3 e eju13881 emission control information this engine conforms to 2006 u.S. Envi- ronmental protection agency (epa) and/or california air resouces board (carb) reg- ulations for marine si engines. This engine is certified to operate on reg- ular unleaded gasoline. Eju21480 approval label of emissi...

  • Page 9: Star Labels

    1-4 e eju18761 star labels this watercraft is labeled with a california air resources board (carb) star label 1. See below for a description of your particu- lar label. One star - low emission the one-star label identifies engines that meet the air resources board’s personal watercraft and outboard ...

  • Page 10

    1-5 e four stars - super ultra low emission the four-star label identifies engines that meet the air resources board’s sterndrive and inboard marine engine 2009 exhaust emission standards. Personal watercraft and outboard marine engines may also comply with these standards. Engines meet- ing these s...

  • Page 11: Important Labels

    1-6 e eju09980 important labels eju13510 label location e_f1g10.Book page 6 tuesday, july 12, 2005 10:26 am.

  • Page 12: Warning Labels

    1-7 e eju13521 warning labels 1 e_f1g10.Book page 7 tuesday, july 12, 2005 10:26 am.

  • Page 13

    1-8 e 6 2 3 5 4 7 e_f1g10.Book page 8 tuesday, july 12, 2005 10:26 am.

  • Page 14: Other Labels

    1-9 e eju13540 other labels 8 9 a 0 b d e c f e_f1g10.Book page 9 tuesday, july 12, 2005 10:26 am.

  • Page 15: Safety Information

    1-10 e eju11770 safety information the safe use and operation of this watercraft is dependent upon the use of proper riding techniques, as well as upon the common sense, good judgment, and expertise of the operator. Every operator should know the following requirements before riding the watercraft. ...

  • Page 16: Cruising Limitations

    1-11 e eju10011 cruising limitations ● scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others. ● operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft. ● do not...

  • Page 17: Operation Requirements

    1-12 e ● this watercraft is not equipped with light- ing required for night operation. Do not operate the watercraft after sunset or before dawn, otherwise you increase the risk of colliding with another boat, which could result in severe injury or death. ● follow navigation rules, and state/provin-...

  • Page 18

    1-13 e ● helmets meeting snell or dot standards are required for ijsba-sanctioned races. You must decide whether to wear a hel- met while you ride for recreation. You should know that a helmet could help pro- tect you in certain kinds of accidents and that it could injure you in others. A helmet is ...

  • Page 19

    1-14 e ● do not attempt to modify this watercraft! Modifications to your watercraft may reduce safety and reliability, and render the watercraft unsafe or illegal for use. ● attach the engine shut-off cord (lanyard) to your wrist and keep it free from the handlebars so that the engine stops if the o...

  • Page 20: Recommended Equipment

    1-15 e eju13810 recommended equipment the following items should be carried on board your watercraft: ● sound-signaling device you should carry a whistle or other sound- signaling device that can be used to sig- nal other boats. See rules of the road for more information. ● visual distress signals i...

  • Page 21: Watercraft Characteristics

    1-16 e eju20030 watercraft characteristics ● jet thrust turns the watercraft. Releasing the throttle lever completely produces only minimum thrust. If you are traveling at speeds above trolling, you will have rapidly decreasing ability to steer without throttle. This model has the yamaha engine mana...

  • Page 22: Rules of The Road

    1-17 e eju11800 rules of the road yamaha watercraft is legally consid- ered a powerboat. Operation of the watercraft must be in accordance with the rules and regulations governing the waterway on which it is used. Just as there are rules that apply when you are driving on streets and highways, there...

  • Page 23: Rules When Encountering

    1-18 e rules when encountering vessels there are three main situations that you may encounter with other vessels which could lead to a collision unless the steering rules are followed: meeting: you are approaching another vessel head-on crossing: you are traveling across another vessel’s path overta...

  • Page 24: Other Special Situations

    1-19 e overtaking if you are passing another vessel, you are the give-way vessel. This means that the other vessel is expected to maintain its course and speed. You must stay out of its way until you are clear of it. Likewise, if another vessel is passing you, you should maintain your speed and dire...

  • Page 25

    1-20 e this system uses buoys and signs with distinctive shapes and colors to show regu- latory or advisory information. These mark- ers are white with black letters and orange borders. They signify speed zones, restricted areas, danger areas, and general information. Remember, markings may vary by ...

  • Page 26: To Get More Boating

    1-21 e eju11810 to get more boating safety information be informed about boating safety. Addi- tional publications and information can be obtained from many organizations, including the following. United states coast guard consumer affairs staff (g-bc) office of boating, public, and consumer affairs...

  • Page 27: Enjoy Your Watercraft

    1-22 e eju10061 enjoy your watercraft responsibly you share the areas you enjoy when riding your watercraft with others and with nature. So your enjoyment includes a responsibility to treat these other people, and the lands, waters, and wildlife with respect and courtesy. Whenever and wherever you r...

  • Page 28: Features and

    E 2 eju10070 features and functions location of main components ..............2-1 operation of controls and other functions ...................................................2-5 seat ........................................................2-5 hood ......................................................

  • Page 29: Location of Main Components

    2-1 e eju10080 location of main components 1 handlebars use to control direction. 2 fuel tank filler cap 3 rope hole 4 footwell use to place feet for balance. 5 intake grate prevents debris from getting into the jet pump. 6 speed sensor e_f1g10.Book page 1 tuesday, july 12, 2005 10:26 am.

  • Page 30

    2-2 e 1 cooling water pilot outlet use to verify cooling water flow. 2 bow eye use to attach rope for transporting, mooring or towing the watercraft in an emergency. 3 front storage compartment 4 hood 5 jet intake 6 handgrip 7 seat 8 glove compartment 9 yamaha adjustable sponson (yas) e_f1g10.Book p...

  • Page 31

    2-3 e 1 engine shut-off cord (lanyard) attach to wrist so that the engine stops if the operator falls off the watercraft. 2 engine stop switch push to stop the engine normally. 3 clip insert into the engine shut-off switch to enable starting of the engine. Remove to stop the engine or prevent acci- ...

  • Page 32

    2-4 e 1 spark plugs/spark plug caps 2 electrical box protects electrical components from water. 3 flush hose connector use to flush the engine cooling water pas- sages. 4 spark plug lead 5 muffler 6 fuel tank 7 oil tank 8 battery 9 fire extinguisher container 0 water separator e_f1g10.Book page 4 tu...

  • Page 33: Operation of Controls and

    2-5 e eju10090 operation of controls and other functions eju10100 seat there is a seat latch 1 at the rear of the seat to remove the seat. To remove the seat: pull the seat latch up, and then pull the seat off. To install the seat: insert the projection on the front of the seat into the stay on the ...

  • Page 34: Hood

    2-6 e eju10110 hood to open the hood, push the latch 1 down, and then lift the hood up. To close the hood, push the hood down to lock it in place. Note: @ make sure that the hood is properly secured before operating the watercraft. @ eju10120 fuel tank filler cap to remove the fuel tank filler cap 1...

  • Page 35: Engine Stop Switch

    2-7 e eju10150 engine stop switch push this switch 1 (red button) to stop the engine normally. Eju10160 engine shut-off switch insert the clip 1, on the end of the engine shut-off cord 2, under the engine shut-off switch 3 (black button). The engine will stop automatically when the clip is removed f...

  • Page 36: Start Switch

    2-8 e eju18610 start switch push the start switch 1 (green button) to start the engine. Note: @ the engine will not start when the clip is removed from the engine shut-off switch or if the throttle lever is squeezed. @ eju10201 cooling water pilot outlet this watercraft is equipped with cooling wate...

  • Page 37: Steering System

    2-9 e eju19950 steering system your watercraft can be steered by turning the handlebars 1 in the direction you wish to travel. When the handlebars are turned, the angle of the jet thrust nozzle 2 is changed and the direction of the watercraft is changed accordingly. Since the strength of the jet thr...

  • Page 38: Quick Shift Trim System

    2-10 e eju10220 quick shift trim system (qsts) selector the qsts selector 1 is located at the left handlebar grip and is used to adjust the trim angle of the watercraft. Operating the qsts selector changes the angle of the jet thrust nozzle vertically. This changes the trim angle of the watercraft. ...

  • Page 39: Handgrip

    2-11 e eju10230 bow down turn the grip to a or b and the bow will go down while the watercraft is on plane. Bow down puts more of the bow in the water. This gives the watercraft more “hook,” which enhances turning performance. This position will also help the watercraft get up on plane more quickly....

  • Page 40: Engine Overheat Warning

    2-12 e eju20451 engine overheat warning system this model is equipped with an engine overheat warning system. If the engine starts to overheat, the warn- ing light and the engine overheat warning indicator begin to blink, and the buzzer sounds intermittently. When this occurs, reduce the engine spee...

  • Page 41: Exhaust Temperature Warning

    2-13 e if the overheat warning is ignored, engine and exhaust system heat may increase, par- ticularly if the watercraft is operated at higher speeds. When this occurs, the warn- ing light, the engine overheat warning indi- cator and the buzzer will change from intermittently to continuously on, and...

  • Page 42: Caution:

    2-14 e caution: @ this model is equipped with a catalytic converter. ● when the exhaust temperature warn- ing system is activated, reduce engine speed (below 4,000 r/min) and return to shore. ● if you cannot locate and correct the cause of the overheating, consult a yamaha dealer. Continuing to oper...

  • Page 43: Multifunction Information

    2-15 e eju20161 multifunction information center this meter contains following functions for the help and convenience of operation. 1 tachometer 2 speedometer 3 hour meter/voltmeter 4 fuel meter 5 warning light 6 fuel warning indicator 7 engine overheat warning indicator 8 oil warning indicator 9 ex...

  • Page 44: Tachometer

    2-16 e eju10280 tachometer the engine speed (r/min) is displayed by segments. Each segment indicates a 250 r/min increment. Eju20171 speedometer the meter shows the watercraft speed against water. Note: @ to switch the speedometer display between kilometers and miles, push the select button 1 for at...

  • Page 45: Hour Meter/voltmeter

    2-17 e eju20183 hour meter/voltmeter note: @ to switch the display between the hour meter and voltmeter, push the select button 1 for at least 1 second after the meter is displayed for more than 10 sec- onds. @ hour meter the hour meter is provided to make it easy to follow the maintenance schedule....

  • Page 46: Oil Warning Indicator

    2-18 e eju10341 oil warning indicator if the oil remaining in the tank drops to about 1.7 l (0.45 us gal, 0.37 imp gal) or the oil filter is clogged, the oil warning indi- cator and the warning light begin to blink. The buzzer also starts sounding intermit- tently. If the oil warning indicators begi...

  • Page 47: Engine Overheat Warning

    2-19 e eju20050 engine overheat warning indicator if the engine starts to overheat, the warn- ing light and engine overheat warning indi- cator begin to blink, and the buzzer sounds intermittently. If the watercraft continues to be operated at higher speeds after the warning system has been activate...

  • Page 48: Storage Compartments

    2-20 e eju10350 storage compartments a front storage compartment and a glove compartment are provided. Note: @ ● make sure that the storage compartments are properly secured before operating the watercraft. ● the storage compartments are not designed to be waterproof. If you carry objects that must ...

  • Page 49: Yamaha Adjustable Sponson

    2-21 e eju20470 glove compartment a glove compartment 2 is located in front of the seat. To open the glove compartment, slide the latch 1 toward you, and then lift up the lid. To close the glove compartment, push the lid down until it locks securely. Glove compartment: capacity: 2 l (0.53 us gal, 0....

  • Page 50: Operation

    E 3 eju10400 operation fuel and oil ...............................................3-1 gasoline .................................................3-1 2-stroke engine oil ..................................3-3 filling the fuel tank .................................3-4 filling the oil tank ................

  • Page 51: Fuel and Oil

    3-1 e eju20060 fuel and oil this engine uses yamaha’s oil injection system, which provides superior lubrication by ensuring the proper oil ratio for all operat- ing conditions. No fuel premixing is neces- sary except during the engine break-in period. Simply pour gasoline into the fuel tank and oil ...

  • Page 52: Caution:

    3-2 e ● avoid overfilling the fuel tank. Stop fill- ing when the fuel level just reaches the bottom of the filler tube. Do not fill up the filler tube because fuel expands as it warms up and could overflow. If tem- porarily leaving the watercraft with a full fuel tank, do not leave it in direct sunl...

  • Page 53: 2-Stroke Engine Oil

    3-3 e eju18320 gasohol there are two types of gasohol: gasohol containing ethanol and that containing meth- anol. Gasohol containing ethanol can be used if ethanol content does not exceed 10% and the fuel meets minimum octane ratings. Gasohol containing methanol is not rec- ommended by yamaha becaus...

  • Page 54: Filling The Fuel Tank

    3-4 e eju20190 filling the fuel tank caution: @ be careful when refueling. Avoid getting water or other contaminants in the fuel tank. Contaminated fuel can cause poor running or engine damage. @ 1. Open the hood and remove the front storage compartment, to check the fuel level. (see page 2-20 for f...

  • Page 55: Filling The Oil Tank

    3-5 e eju10460 filling the oil tank warning @ ● do not add gasoline to the oil tank. Fire or explosion could result. ● oil in the bilge is a serious fire hazard. Wipe up any spilled oil immediately. @ caution: @ do not allow the oil tank to become com- pletely empty. If the oil tank becomes empty th...

  • Page 56: Pre-Operation Checks

    3-6 e eju13460 pre-operation checks eju13470 pre-operation check list before operating this watercraft, perform the checks in the following check list. See the accompanying text in this chapter for details on how to perform the checks. Warning @ if any item in the pre-operation check list is not wor...

  • Page 57: Pre-Operation Check Points

    3-7 e eju10480 pre-operation check points eju10500 engine compartment ventilate the engine compartment before each use. To ventilate the engine compartment, remove seat and front storage compart- ment. (see page 2-5 for seat, and 2-20 for front storage compartment.) allow the engine compartment to r...

  • Page 58

    3-8 e eju20071 fuel and oil systems check the fuel system for leakage, cracks or malfunctions before each use. (see page 4-11 for check points and correct proce- dures.) 1. Remove the fuel tank filler cap to release any pressure that might have built up in the fuel tank. 2. Remove seat and front sto...

  • Page 59: Caution:

    3-9 e eju20200 bilge check for moisture and fuel residue in the bilge. This watercraft is equipped with a conven- tional jet vacuum bilge draining system and an electric bilge draining system. The elec- tric bilge draining system is operated when the engine is running. When excess water reaches the ...

  • Page 60: Caution:

    3-10 e caution: @ ● make sure that the stern drain plugs are tightened securely before launch- ing the watercraft. Otherwise, water may flood the engine compartment and cause the watercraft to submerge. ● clean any foreign materials, such as dirt or sand, from the drain plug threads before installin...

  • Page 61

    3-11 e eju11880 fire extinguisher check that there is a full fire extinguisher on board. The fire extinguisher container 1 is located in the battery compartment. To open the fire extinguisher container cap 2 remove the seat and turn it counter- clockwise. After inserting the fire extinguisher make s...

  • Page 62: Warning

    3-12 e eju18340 throttle squeeze and release the throttle lever several times to make sure that there is no hesitation in its travel. It should be smooth over the complete range, and spring back to the idle position when released. Warning @ before starting the engine, always check the operation of t...

  • Page 63

    3-13 e eju20620 quick shift trim system (qsts) check the shift lock lever and the qsts selector for proper operation. 1. Operate the shift lock lever and the qsts selector to check that they oper- ate properly. 2. Check that the qsts selector locks when the lever is released. 3. Check that the selec...

  • Page 64: Warning

    3-14 e eju10580 jet unit carefully check the jet intake for weeds, debris, or anything else that might restrict the intake of water. If the intake is clogged, cavitation could occur, reducing jet thrust, and possibly damaging the jet pump. In some cases, the engine may overheat because of lack of co...

  • Page 65: Caution:

    3-15 e eju18352 switches caution: @ do not run the engine of the watercraft for more than 15 seconds on land with- out supplying water, otherwise the engine may overheat. @ check the start switch, the engine stop switch, and the engine shut-off switch for proper operation. Push the start switch 1 to...

  • Page 66: Operation

    3-16 e eju18360 operation warning @ before operating your watercraft, become familiar with all controls. Con- sult your yamaha dealer about any con- trol or function you do not fully understand. Failure to understand how controls work could cause an accident or prevent you from avoiding an accident....

  • Page 67: Caution:

    3-17 e 1. Launch the watercraft and start the engine. (see page 3-18 for engine start- ing procedures.) 2. Run the engine at the lowest possible speed for 5 minutes. 3. Gradually open the throttle and run the engine at 5,000 r/min or less. 4. Continue operation at 5,000 r/min or less until the first...

  • Page 68: Starting The Engine

    3-18 e eju18080 starting the engine warning @ never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monox- ide, a colorless, odorless gas that may cause loss of consciousness and death within a short time. Always operate the watercraft in an op...

  • Page 69: Warning

    3-19 e 2. Attach the clip 1 to the engine shut-off switch 2. Also, attach the engine shut- off cord 3 to your left wrist. Warning @ check that the engine shut-off cord is not frayed or broken, and keep it free from the handlebars so the engine stops if the operator falls off. The engine shut-off cor...

  • Page 70: Stopping The Engine

    3-20 e eju10660 stopping the engine to stop the engine, release the throttle lever, and then push the engine stop switch (red button). Warning @ you need throttle to steer. Shutting off the engine can cause you to hit an obsta- cle you are attempting to avoid. A colli- sion could result in severe in...

  • Page 71: Operating Your Watercraft

    3-21 e eju10680 operating your watercraft eju11900 getting to know your watercraft operating your watercraft requires skills acquired through practice over a period of time. Take the time to learn the basic tech- niques well before attempting more difficult maneuvers. Operating your new watercraft c...

  • Page 72: Riding Watercraft With A

    3-22 e wear protective clothing. Severe internal injuries can occur if water is forced into body cavities as result of falling into the water or being near the jet thrust nozzle. Normal swimwear does not adequately protect against forceful water entry into rectum and vagina. All riders must wear a w...

  • Page 73: Starting The Watercraft

    3-23 e eju18370 starting the watercraft warning @ ● scan constantly for people, objects, and other watercraft. Be alert for con- ditions that limit your visibility or block your vision of others. ● operate defensively at safe speeds and keep a safe distance away from people, objects, and other water...

  • Page 74

    3-24 e eju10730 starting and boarding in shallow water 1. Do not start the engine in less than 60 cm (2 ft) of water. Put the watercraft in water that is deep enough, and then board the watercraft from the side or the rear. 2. Attach the engine shut-off cord to your left wrist, and then install the ...

  • Page 75: Water

    3-25 e eju10750 boarding and starting in deep water warning @ ● operator and passenger should prac- tice getting on board in shallow water before riding in deep water. Boarding in deep water requires more skill. ● the fatigue and exposure that could result after unsuccessful attempts to get back on ...

  • Page 76: Warning

    3-26 e eju10771 boarding with a passenger warning @ severe internal injuries can occur if water is forced into body cavities as a result of being near the jet thrust nozzle. Do not apply throttle until the passenger is seated with his or her feet on the floor of the footwell and is holding on to the...

  • Page 77: Capsized Watercraft

    3-27 e note: @ the heavier the total weight of the operator and passengers, the more difficult it will be to balance the watercraft. Do not operate the watercraft when the total weight exceeds 160 kg (353 lb) including any cargo. If it is difficult to balance the watercraft at a stand- still, procee...

  • Page 78: Caution:

    3-28 e 1. Remove the clip from the engine shut-off switch. 2. Swim to the rear of the watercraft. Pull the watercraft over with your left hand on the ride plate while pushing down on the gunwale with your right hand or foot. Note: @ if the port (left) side of the capsized water- craft is tilting up,...

  • Page 79: Turning The Watercraft

    3-29 e eju19960 turning the watercraft steering control depends on the combi- nation of handlebar position and the amount of throttle. Water sucked in through the intake grate is pressurized by the impeller in the jet pump. As the pressurized water is expelled from the pump through the jet thrust no...

  • Page 80: Warning

    3-30 e warning @ ● do not release the throttle lever when trying to steer away from objects—you need throttle to steer. A collision could result in severe injury or death. ● when operating at higher speeds, make gradual turns or slow down before turning. Sharp high-speed turns may cause the watercra...

  • Page 81: Stopping The Watercraft

    3-31 e eju10800 stopping the watercraft the watercraft is not equipped with a sep- arate braking system. It is stopped by water resistance when the throttle lever is released. From full speed, the watercraft comes to a complete stop in approximately 125 m (410 ft) after the throttle is released and ...

  • Page 82: Beaching The Watercraft

    3-32 e eju10810 beaching the watercraft 1. Make sure no obstructions, boats or swimmers are near the beach. Release the throttle lever about 125 m (410 ft) before you reach the intended beaching area. 2. Approach the beach slowly and stop the engine before reaching land. Remember: you need throttle ...

  • Page 83: Post-Operation Checks

    3-33 e eju20210 post-operation checks warning @ stay away from stern when engine is run- ning on land. Hot water and steam spurt- ing from exhaust outlet into the air can cause serious burns. @ always perform the following post-opera- tion checks after operating the watercraft. 1. Remove the watercr...

  • Page 84: Caution:

    3-34 e 7. If the watercraft will be stored for a week or more, lubricate internal engine com- ponents to help prevent corrosion. (see page 4-3 for lubrication procedures.) 8. Rinse the engine and engine compart- ment with a small amount of water. Caution: @ do not use high pressure when rinsing the ...

  • Page 85: Transporting

    3-35 e eju20090 transporting when transporting the watercraft on a trailer, secure the tie downs to the trailer through the bow eye and stern rope holes. Caution: @ do not route ropes or tie downs over the seat, as they may leave permanent marks on the seat’s surface. Also, wrap the ropes or tie dow...

  • Page 86: Maintenance and

    E 4 eju10860 maintenance and care storage ......................................................4-1 flushing the cooling system ..................4-1 lubrication ..............................................4-3 fuel system ............................................4-3 battery .......................

  • Page 87: Storage

    4-1 e eju18121 storage warning @ always place the watercraft upright in a horizontal position when storing it, oth- erwise fuel could leak out into the engine or engine compartment, which could result in a fire hazard. @ storage for prolonged periods of time, such as winter storage, requires prevent...

  • Page 88

    4-2 e 1. Put the watercraft on land in a horizontal position. 2. Open the flushing hose connector cap 1, and then insert the garden hose adapter 2 into the flushing hose con- nector 3 and turn it until it is securely connected. 3. Connect the garden hose adapter to a water tap using a hose. Note: @ ...

  • Page 89: Lubrication

    4-3 e eju20440 lubrication warning @ do not spray flammable rust inhibitor products on engine surfaces while the engine is hot. The sprayed substance or propellants could catch fire. @ 1. Remove the spark plugs and pour approximately one tablespoon of oil into each cylinder. 2. Grease the spark plug...

  • Page 90: Caution:

    4-4 e ● take care not to spill gasoline. If gaso- line spills, wipe it up immediately with dry rags. Always properly dispose of gasoline-soaked rags. ● avoid overfilling the fuel tank. Stop fill- ing when the fuel level just reaches the bottom of the filler tube. Do not fill up the filler tube becau...

  • Page 91: Battery

    4-5 e eju19700 battery if the watercraft will not be used for more than a month, disconnect the negative (–) lead first, then the positive (+) lead and breather hose, and then remove the battery from the watercraft. Clean the battery casing using fresh water. If the battery terminals are dirty or co...

  • Page 92: Cleaning The Watercraft

    4-6 e note: @ the condition of the battery can be known by checking the specific gravity of the elec- trolyte. However, you can also know the con- dition of the battery by measuring the voltage at both battery terminals. Charge the battery if the voltage is less than 12 volts. It is recommended to h...

  • Page 93: Maintenance and

    4-7 e eju11971 maintenance and adjustments periodic inspection, adjustment and lubri- cation will keep your watercraft in the safest and most efficient condition possible. Safety is an obligation of the watercraft owner. Proper maintenance must be carried out to keep the exhaust emission and sound l...

  • Page 94

    4-8 e ● modifications to this watercraft not approved by yamaha may cause loss of performance or excessive noise, or render it unsafe for use. Consult a yamaha dealer before attempting any changes. @ note: @ a service manual is available for purchase through a yamaha dealer for owners who have the m...

  • Page 95: And Tool Kit

    4-9 e eju21730 owner’s/operator’s manual and tool kit it is advisable always to carry the owner’s/operator’s manual and tool kit with you whenever you use the watercraft. For your convenience, a storage compartment 1 is provided on the water- craft for the manual and tool kit. Note: @ to protect the...

  • Page 96: Periodic Maintenance Chart

    4-10 e eju13550 periodic maintenance chart the following chart gives general guidelines for periodic maintenance. However, depend- ing on your operating conditions maintenance may need to be performed more frequently. Pmc-*** ( ● ) this mark indicates maintenance that you may do yourself. ( ❍ ) this...

  • Page 97: Inspecting The Fuel System

    4-11 e eju18160 inspecting the fuel system warning @ gasoline is highly flammable and explo- sive. Failure to check for and repair any fuel leakage could result in fire or explo- sion. A fire or explosion can cause severe injury or death. Shut off the engine. Do not smoke. Avoid spilling gasoline. F...

  • Page 98: Inspecting The Oil Injection

    4-12 e eju11000 inspecting the oil injection system check the oil injection system for leakage, cracks, or malfunctions. If necessary, have a yamaha dealer repair the oil injection sys- tem. Check: ● oil tank for damage, cracks or leakage. ● oil tank for water or dirt. ● oil hose and joint for damag...

  • Page 99: Angle

    4-13 e eju18891 inspecting the jet thrust nozzle angle check for smooth operation of the handle- bars and jet thrust nozzle. Turn the handlebars as far as possible to the right and left and check that the differ- ence of distances a and b between the jet thrust nozzle and the nozzle is within specif...

  • Page 100: Cleaning and Adjusting The

    4-14 e eju11062 cleaning and adjusting the spark plugs the spark plug is an important engine component and is easy to inspect. The con- dition of the spark plug can indicate some- thing about the condition of the engine. For example, if the center electrode porcelain is very white, this could indica...

  • Page 101: Warning

    4-15 e note: @ ● wipe off any water on the spark plug or inside the cap before installing the spark plug cap. Push the spark plug cap down until it is securely installed. ● if a torque wrench is not available when you are installing a new spark plug, a good estimate of the correct torque is 1/4 turn...

  • Page 102: Lubrication Points

    4-16 e eju20113 lubrication points to keep moving parts sliding or rotating smoothly, coat them with water-resistant grease. Recommended water resistant grease: yamaha marine grease/yamaha grease a ● throttle cable (handlebar end) pull the throttle lever and remove the seal 1. Spray a rust inhibitor...

  • Page 103

    4-17 e ● qsts cables (pulley end) ● qsts cables (handlebar end) remove the qsts cable housing. Spray a rust inhibitor into the outer cable. Reinstall the qsts cable housing. ● intermediate housing using a grease gun, fill the intermediate housing with water-resistant grease through the grease nipple...

  • Page 104: Inspecting The Battery

    4-18 e eju19710 inspecting the battery check the level of the battery electrolyte and make sure that the negative and posi- tive leads are securely tightened. Warning @ ● battery electrolyte is poisonous and dangerous, causing severe burns, etc. Electrolyte contains sulfuric acid. Avoid contact with...

  • Page 105: Caution:

    4-19 e to replenish the battery: 1. Make sure that the electrolyte level is between the upper 1 and lower 2 level marks. 2. Refill the battery with distilled water if necessary. Caution: @ normal tap water contains minerals that are harmful to a battery. Use only dis- tilled water for replenishing t...

  • Page 106: Adjusting The Fuel Injection

    4-20 e eju18231 adjusting the fuel injection system the fuel injection system was set at the yamaha factory. Have a yamaha dealer ser- vice the watercraft if necessary. Caution: @ do not attempt to adjust the fuel injection system. If the settings are changed poor engine performance and damage may r...

  • Page 107: Replacing The Fuse

    4-21 e eju18250 replacing the fuse the fuse is in the electrical box 1. To replace the fuse: 1. Remove the cap 2. 2. Replace the fuse 4 with the spare fuse 5 of the correct amperage by using the special tool 3 on the reverse side of the cap. Warning @ do not use fuses of higher amperage than those r...

  • Page 108: Adjusting The Yamaha

    4-22 e eju11131 adjusting the yamaha adjustable sponson (yas) the yamaha adjustable sponsons can be adjusted to enhance watercraft performance according to operator preference and oper- ating conditions. (see page 2-21 for an explanation of various positions.) to adjust the yas: 1. Remove the bolts ...

  • Page 109: Specifications

    4-23 e eju13590 specifications spc-*** model item unit gp1300r watercraft capacity maximum people on board number of people 2 maximum load capacity kg (lb) 160 (353) dimensions length mm (in) 2,930 (115.4) width mm (in) 1,150 (45.3) height mm (in) 1,020 (40.2) dry weight kg (lb) 297 (655) performanc...

  • Page 110: Troubleshooting

    E 5 eju11150 troubleshooting and emergency procedures troubleshooting ......................................5-1 troubleshooting chart ............................5-1 emergency procedures ..........................5-4 cleaning the jet intake and impeller ......5-4 jumping the battery ...................

  • Page 111: Troubleshooting

    5-1 e eju11160 troubleshooting if you have any trouble with your watercraft, use this section to check for the possible cause. If you cannot find the cause, or if the procedure for replacement or repair is not described in this owner’s/operator’s manual, have a yamaha dealer perform the necessary se...

  • Page 112

    5-2 e engine runs irregu- larly or stalls fuel empty refill as soon as possi- ble 3-4 stale or contaminated have serviced by yamaha dealer 4-11 fuel tank water or dirt present have serviced by yamaha dealer 4-11 spark plug fouled or defective replace 4-14 incorrect heat range replace 4-14 gap incorr...

  • Page 113

    5-3 e watercraft slow or loses power cavitation jet intake clogged clean 5-4 impeller damaged or worn have serviced by yamaha dealer — engine overheated jet intake clogged clean 5-4 spark plug fouled or defective replace 4-14 incorrect heat range replace 4-14 gap incorrect adjust 4-14 spark plug cap...

  • Page 114: Emergency Procedures

    5-4 e eju11180 emergency procedures eju21602 cleaning the jet intake and impeller if weeds or debris get caught in the intake or impeller, cavitation can occur, causing jet thrust to decrease even though engine speed rises. If this condition is allowed to continue, the engine will overheat and may s...

  • Page 115: Caution:

    5-5 e 2. Remove any weeds or debris from around the drive shaft, impeller, pump housing, and jet thrust nozzle. If debris is difficult to remove, consult your yamaha dealer. Caution: @ always avoid operating your watercraft in areas where weed growth is thick. If trav- eling in weeded areas is unavo...

  • Page 116: Caution:

    5-6 e eju18820 connecting the jumper cables 1. Connect the positive (+) jumper cable 1 to the positive (+) terminals of both bat- teries. 2. Connect one end of the negative (–) jumper cable 2 to the negative (–) termi- nal of the booster battery 3. 3. Connect the other end of the negative (–) cable ...

  • Page 117: Towing The Watercraft

    5-7 e eju19130 towing the watercraft if the watercraft becomes inoperative in the water, it can be towed to shore. If the watercraft must be towed in an emergency using a towline, the operator should ride the watercraft, holding onto the handlebars. Caution: @ ● tow the watercraft at 5 mph (8 km/h) ...

  • Page 118: Submerged Watercraft

    5-8 e eju19020 submerged watercraft if the watercraft is submerged or flooded with water, follow the procedure below and consult a yamaha dealer as soon as possi- ble. Failure to do so may result in serious engine damage! In an emergency: 1. Beach the watercraft and remove the stern drain plugs to d...

  • Page 119: Appendix

    E 6 eju11240 appendix limited warranty ................................... 6-1 yamaha extended service (y.E.S.) .................................................. 6-3 index ...................................................... 6-4 e_f1g10.Book page 1 tuesday, july 12, 2005 10:26 am.

  • Page 120: Limited Warranty

    6-1 e eju12000 limited warranty lwt-catae yamaha motor corporation, u.S.A. Watercraft limited warranty yamaha motor corporation is proud of its heritage and reputation for producing products with high standards of quality and workman- ship. Product excellence provides the cornerstone for our commitm...

  • Page 121

    6-2 e this warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Yamaha motor corporation, u.S.A. Post office box 6555 cypress, california 90630 warranty questions and answers q. What costs are my responsibility during the warranty period? A. Th...

  • Page 122

    6-3 e eju19862 yamaha extended service (y.E.S.) keep your yamaha protected even after your warranty expires with genuine yamaha extended service (y.E.S.). ● ● ● ● y.E.S. Is designed and administered by yamaha motor corporation to provide maximum owner satisfaction. You get uninterrupted factory-back...

  • Page 123: Index

    6-4 e eju11250 index 2-stroke engine oil................................... 3-3 a adjusting the fuel injection system ........ 4-20 adjusting the yamaha adjustable sponson (yas) ..................................... 4-22 approval label of emission control certificate....................................

  • Page 124

    6-5 e inspecting the oil injection system......... 4-12 j jet unit................................................... 3-14 jumping the battery................................. 5-5 l label location .......................................... 1-6 launching the watercraft....................... 3-17 lea...

  • Page 125

    6-6 e to get more boating safety information ............................................ 1-21 towing the watercraft.............................. 5-7 transporting .......................................... 3-35 troubleshooting ...................................... 5-1 troubleshooting chart ..........

  • Page 126

    Printed in usa aug. 2005—1.6 × 1 cr f1g-f8199-13 (e) yamaha motor corporation, usa.