1. DL manuals
  2. Yamaha
  3. Motorcycle
  4. Majesty YP400Y
  5. Owner's Manual

Yamaha Majesty YP400Y Owner's Manual

Manual is about: 34B-28199-10

Summary of Majesty YP400Y

  • Page 1

    34b-28199-10 yp400y owner’s manual read this manual carefully before operating this vehicle. Lit-11626-22-28.

  • Page 2

    Eau10042 read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold. Q.

  • Page 3

    Introduction eau10092 congratulations on your purchase of the yamaha yp400y. This model is the result of yamaha’s vast experience in the pro- duction of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reli- ability that have made yamaha a l...

  • Page 4

    Important manual information eau10132 particularly important information is distinguished in this manual by the following notations: this is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injur...

  • Page 5

    Important manual information eau10193 yp400y owner’s manual ©2008 by yamaha motor corporation, u.S.A. 1st edition, may 2008 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor corporation, u.S.A. Is expressly prohibited. Printed in japan. P/n lit-11...

  • Page 6

    Table of contents location of important labels ..............................................1-1 safety information ...................2-1 further safe-riding points .................2-5 description ...................................3-1 left view ...........................................3-1 right...

  • Page 7

    Table of contents replacing a front turn signal light bulb ............................................7-35 replacing a rear turn signal light bulb ............................................7-36 replacing the license plate light bulb ............................................7-37 troubleshooting...

  • Page 8

    1-1 1 location of important labels eau10382 read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is av...

  • Page 9

    Location of important labels 1-2 1 2 3 4 5 6 7 8 9 notice cleaning with alkaline or acid cleaner, gasoline or solvent will damage windshield. Use neutral detergent. 8et—2815k—00 1 warning before you operate this vehicle, read the owner’s manual and all labels. Always wear an approved motorcycle helm...

  • Page 10

    Location of important labels 1-3 1 2 3 4 5 6 7 8 9 7 5ru-21686-00

  • Page 11

    2-1 2 3 4 5 6 7 8 9 safety information eau10263 be a responsible owner as the vehicle’s owner, you are respon- sible for the safe and proper operation of your scooter. Scooters are single-track vehicles. Their safe use and operation are de- pendent upon the use of proper riding techniques as well as...

  • Page 12

    Safety information 2-2 1 2 ed by road and traffic conditions. ● always signal before turning or changing lanes. Make sure that other motorists can see you. ● the posture of the operator and passenger is important for proper control. ● the operator should keep both hands on the handlebar and both fee...

  • Page 13

    Safety information 2-3 1 2 engine exhaust can be drawn into a building through openings such as windows and doors. Loading adding accessories or cargo to your scooter can adversely affect stability and handling if the weight distribution of the scooter is changed. To avoid the possibility of an acci...

  • Page 14

    Safety information 2-4 1 2 or others. Installing aftermarket prod- ucts or having other modifications per- formed to your vehicle that change any of the vehicle’s design or operation characteristics can put you and others at greater risk of serious injury or death. You are responsible for injuries r...

  • Page 15

    Safety information 2-5 1 2 eau10371 further safe-riding points ● be sure to signal clearly when making turns. ● braking can be extremely difficult on a wet road. Avoid hard braking, because the scooter could slide. Apply the brakes slowly when stopping on a wet surface. ● slow down as you approach a...

  • Page 16

    3-1 1 2 3 4 5 6 7 8 9 description eau10410 left view 10 1 2 3 5 6 7 8 4 11 9 1. Headlight (page 7-34) 2. Fuel tank cap (page 4-9) 3. Rear storage compartment (page 4-14) 4. V-belt case air filter element (page 7-20) 5. Owner’s tool kit (page 7-2) 6. Fuses (page 7-33) 7. Battery (page 7-32) 8. Shock ...

  • Page 17

    Description 3-2 2 3 4 5 6 7 8 9 eau10420 right view 5 1 2 3 4 7 6 8 1. Grab bar (page 6-2) 2. Passenger seat (page 4-12) 3. Rider seat (page 4-12) 4. Coolant reservoir (page 7-18) 5. Radiator 6. Centerstand (page 7-30) 7. Air filter element (right) (page 7-20) 8. Shock absorber assembly spring prelo...

  • Page 18

    Description 3-3 1 2 3 4 5 6 7 8 9 eau10430 controls and instruments 1 3 4 5 6 7 8 9 10 11 12 2 1. Rear brake lever (page 4-8) 2. Left handlebar switches (page 4-7) 3. Rear brake lock lever (page 4-8) 4. Speedometer (page 4-2) 5. Multi-function display (page 4-3) 6. Tachometer (page 4-3) 7. Right han...

  • Page 19

    4-1 2 3 4 5 6 7 8 9 instrument and control functions eau10460 main switch/steering lock the main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. Eau36070 on all electrical circuits are supplied with power; ...

  • Page 20

    Instrument and control functions 4-2 1 2 3 4 5 6 7 8 9 eau11003 indicator and warning lights eau11030 turn signal indicator lights “ ” and “ ” the corresponding indicator light flash- es when the turn signal switch is pushed to the left or right. Eau11080 high beam indicator light “ ” this indicator...

  • Page 21

    Instrument and control functions 4-3 2 3 4 5 6 7 8 9 eau11872 tachometer the electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range. When the key is turned to “on”, the ta- chometer needle will sweep once across the r/min range and then return to ze...

  • Page 22

    Instrument and control functions 4-4 1 2 3 4 5 6 7 8 9 cator started flashing) ● a self-diagnosis device ● a clock ● an ambient temperature display ● an oil change indicator ● a v-belt replacement indicator tip ● be sure to turn the key to “on” be- fore using the “select” and “reset” buttons. ● when...

  • Page 23

    Instrument and control functions 4-5 2 3 4 5 6 7 8 9 vehicle and let the engine cool. (see page 7-39.) notice eca10021 do not continue to operate the en- gine if it is overheating. Oil change indicator “oil” this indicator flashes at the initial 1000 km (600 mi), then at 5000 km (3000 mi) and every ...

  • Page 24

    Instrument and control functions 4-6 1 2 3 4 5 6 7 8 9 notice eca11790 if the multi-function display indi- cates an error code, the vehicle should be checked as soon as pos- sible in order to avoid engine dam- age. Clock mode to set the clock: 1. Push the “select” button and “reset” button together ...

  • Page 25

    Instrument and control functions 4-7 2 3 4 5 6 7 8 9 eau12347 handlebar switches left right eau12400 dimmer switch “ / ” set this switch to “ ” for the high beam and to “ ” for the low beam. Eau12460 turn signal switch “ / ” to signal a right-hand turn, push this switch to “ ”. To signal a left-hand...

  • Page 26

    Instrument and control functions 4-8 1 2 3 4 5 6 7 8 9 eau12900 front brake lever the front brake lever is located on the right handlebar grip. To apply the front brake, pull this lever toward the handle- bar grip. Eau12950 rear brake lever the rear brake lever is located on the left handlebar grip....

  • Page 27

    Instrument and control functions 4-9 2 3 4 5 6 7 8 9 rear brake lock lever is applied. ● to provide secure locking of the rear wheel, apply the rear brake le- ver first before moving the rear brake lock lever to the left. Warning ewa12361 never move the rear brake lock lever to the left while the ve...

  • Page 28

    Instrument and control functions 4-10 1 2 3 4 5 6 7 8 9 move it. 3. Close the lid. Warning ewa11121 be sure that the fuel tank cap is properly installed and locked before riding the scooter. Leaking fuel is a fire hazard. Eau13212 fuel make sure there is sufficient gasoline in the tank. Warning ewa1...

  • Page 29

    Instrument and control functions 4-11 2 3 4 5 6 7 8 9 your eyes, see your doctor immedi- ately. If gasoline spills on your skin, wash with soap and water. If gaso- line spills on your clothing, change your clothes. Eau36081 notice eca11400 use only unleaded gasoline. The use of leaded gasoline will ...

  • Page 30

    Instrument and control functions 4-12 1 2 3 4 5 6 7 8 9 pairable damage to the catalytic converter. Eau34140 seats rider seat to open the rider seat 1. Place the scooter on the center- stand. 2. Insert the key into the main switch, and then turn it counterclockwise. Tip do not push inward when turni...

  • Page 31

    Instrument and control functions 4-13 2 3 4 5 6 7 8 9 to close the rider seat 1. Fold the rider seat down, and then push it down to lock it in place. 2. Remove the key from the main switch if the scooter will be left un- attended. Tip make sure that the rider seat is properly secured before riding. ...

  • Page 32

    Instrument and control functions 4-14 1 2 3 4 5 6 7 8 9 3. Slide the rider seat forward or backward to the desired position. 4. Install bolts and securely tighten them. 5. Close the rider seat. Eau14493 storage compartments front storage compartment a to open the storage compartment when it is locke...

  • Page 33

    Instrument and control functions 4-15 2 3 4 5 6 7 8 9 to close the storage compartment, push the lid into the original position. Warning! Do not store heavy items in this compartment. [ewa11161] rear storage compartment two helmets can be stored in the stor- age compartment under the seats. (see pag...

  • Page 34

    Instrument and control functions 4-16 1 2 3 4 5 6 7 8 9 eau14891 adjusting the shock absorber assemblies each shock absorber assembly is equipped with a spring preload adjust- ing ring. Notice eca10101 to avoid damaging the mechanism, do not attempt to turn beyond the maximum or minimum settings. Wa...

  • Page 35

    Instrument and control functions 4-17 2 3 4 5 6 7 8 9 pair it if it does not function proper- ly. Eau15373 ignition circuit cut-off system the ignition circuit cut-off system (com- prising the sidestand switch and brake light switches) has the following func- tions. ● it prevents starting when the s...

  • Page 36

    Instrument and control functions 4-18 1 2 3 4 5 6 7 8 9 with the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is turned on. 3. Turn the key on. 4. Keep the front or rear brake applied. 5. Push the start switch. Does the engine start? With the engine still o...

  • Page 37

    5-1 2 3 4 5 6 7 8 9 for your safety – pre-operation checks eau15595 inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the owner’s manual. Warning ewa11151 failure to in...

  • Page 38

    For your safety – pre-operation checks 5-2 1 2 3 4 5 6 7 8 9 eau15605 pre-operation check list item checks page fuel ● check fuel level in fuel tank. ● refuel if necessary. ● check fuel line for leakage. 4-10 engine oil ● check oil level in engine. ● if necessary, add recommended oil to specified le...

  • Page 39

    For your safety – pre-operation checks 5-3 2 3 4 5 6 7 8 9 wheels and tires ● check for damage. ● check tire condition and tread depth. ● check air pressure. ● correct if necessary. 7-23, 7-25 brake levers ● make sure that operation is smooth. ● lubricate lever pivoting points if necessary. 7-29 cen...

  • Page 40

    6-1 1 2 3 4 5 6 7 8 9 operation and important riding points eau15951 read the owner’s manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your yamaha dealer. Warning ewa10271 failure to familiarize yourself with the controls can lead to...

  • Page 41

    Operation and important riding points 6-2 2 3 4 5 6 7 8 9 eau16761 starting off tip before starting off, allow the engine to warm up. 1. While pulling the rear brake lever with your left hand and holding the grab bar with your right hand, push the scooter off the centerstand. 2. Sit astride the seat...

  • Page 42

    Operation and important riding points 6-3 1 2 3 4 5 6 7 8 9 front rear eau16841 engine break-in there is never a more important period in the life of your engine than the period between 0 and 1600 km (1000 mi). For this reason, you should read the follow- ing material carefully. Since the engine is ...

  • Page 43

    Operation and important riding points 6-4 2 3 4 5 6 7 8 9 eau17213 parking when parking, stop the engine, and then remove the key from the main switch. Warning ewa10311 ● since the engine and exhaust system can become very hot, park in a place where pedestri- ans or children are not likely to touch ...

  • Page 44

    7-1 1 2 3 4 5 6 7 8 9 periodic maintenance and adjustment eau17272 periodic inspection, adjustment, and lu- brication will keep your vehicle in the safest and most efficient condition pos- sible. Safety is an obligation of the vehi- cle owner/operator. The most important points of vehicle inspection...

  • Page 45

    Periodic maintenance and adjustment 7-2 2 3 4 5 6 7 8 9 eau17502 owner’s tool kit the owner’s tool kit is located inside the rear storage compartment. (see page 4-14.) pull up the storage compartment mat, and then remove the owner’s tool kit. The service information included in this manual and the t...

  • Page 46

    Periodic maintenance and adjustment 7-3 1 2 3 4 5 6 7 8 9 eau17600 periodic maintenance chart for the emission control system * since these items require special tools, data and technical skills, have a yamaha dealer perform the service. No. Item routine initial odometer readings 600 mi (1000 km) or...

  • Page 47

    Periodic maintenance and adjustment 7-4 2 3 4 5 6 7 8 9 eau32185 general maintenance and lubrication chart no. Item routine initial odometer readings 600 mi (1000 km) or 1 month 4000 mi (7000 km) or 6 months 8000 mi (13000 km) or 12 months 12000 mi (19000 km) or 18 months 16000 mi (25000 km) or 24 m...

  • Page 48

    Periodic maintenance and adjustment 7-5 1 2 3 4 5 6 7 8 9 10 * steering bearings ● check bearing assemblies for looseness. √ √ √ √ √ √ ● moderately repack with lith- ium-soap-based grease. Every 12000 mi (19000 km) 11 * chassis fasteners ● check all chassis fitting and fas- teners. ● correct if nece...

  • Page 49

    Periodic maintenance and adjustment 7-6 2 3 4 5 6 7 8 9 * since these items require special tools, data and technical skills, have a yamaha dealer perform the service. Tip from 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months. 19 engine...

  • Page 50

    Periodic maintenance and adjustment 7-7 1 2 3 4 5 6 7 8 9 eau36370 tip ● the air filters and v-belt filter need more frequent service if you are riding in unusually wet or dusty areas. ● hydraulic brake service ● after disassembling the brake master cylinders and calipers, always change the fluid. R...

  • Page 51

    Periodic maintenance and adjustment 7-8 2 3 4 5 6 7 8 9 eau18712 removing and installing cowlings and panels the cowlings and panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a cowling or panel needs to be re- moved an...

  • Page 52

    Periodic maintenance and adjustment 7-9 1 2 3 4 5 6 7 8 9 cowling b to remove the cowling 1. Remove the screws. 2. Remove the cowling as shown. To install the cowling place the cowling in the original posi- tion, and then install the screws. Cowlings c and d to remove one of the cowlings 1. Remove c...

  • Page 53

    Periodic maintenance and adjustment 7-10 2 3 4 5 6 7 8 9 2. Install the screw access cover by placing it in its original position. 3. Install the grab bar by installing the collars and grab bar bolts. 4. Install the passenger seat. 5. Install cowlings a and b. Cowling e to remove the cowling 1. Pull...

  • Page 54

    Periodic maintenance and adjustment 7-11 1 2 3 4 5 6 7 8 9 eau34290 panel a to remove the panel 1. Remove the bolts. 2. Pull the panel out as shown. To install the panel place the panel in the original position, and then install the bolts. Panel b to remove the panel remove the screws, and then pull...

  • Page 55

    Periodic maintenance and adjustment 7-12 2 3 4 5 6 7 8 9 eau34172 checking the spark plug the spark plug is an important engine component, which is easy to check. Since heat and deposits will cause any spark plug to slowly erode, the spark plug should be removed and checked in accordance with the pe...

  • Page 56

    Periodic maintenance and adjustment 7-13 1 2 3 4 5 6 7 8 9 necessary. To install the spark plug 1. Measure the spark plug gap with a wire thickness gauge and, if nec- essary, adjust the gap to specifica- tion. 2. Clean the surface of the spark plug gasket and its mating surface, and then wipe off an...

  • Page 57

    Periodic maintenance and adjustment 7-14 2 3 4 5 6 7 8 9 eau36110 canister this model is equipped with a canister to prevent the discharging of fuel vapor into the atmosphere. Before operating this vehicle, make sure to check the fol- lowing: ● check each hose connection. ● check each hose and canis...

  • Page 58

    Periodic maintenance and adjustment 7-15 1 2 3 4 5 6 7 8 9 to collect the used oil. 3. Remove the engine oil filler cap and the engine oil drain bolt to drain the oil from the crankcase. 4. Check the washer for damage and replace it if necessary. Tip skip steps 5–7 if the oil filter element is not b...

  • Page 59

    Periodic maintenance and adjustment 7-16 2 3 4 5 6 7 8 9 7. Install the compression spring and oil filter element cover by installing the bolts, then tightening them to the specified torque. Tip make sure that the o-rings are properly seated. 8. Install the washer and the engine oil drain bolt, and ...

  • Page 60

    Periodic maintenance and adjustment 7-17 1 2 3 4 5 6 7 8 9 3. Release the “oil change” but- ton, and the oil change indicator will go off. Tip if the engine oil is changed before the oil change indicator comes on (i.E. Be- fore the periodic oil change interval has been reached), the indicator must b...

  • Page 61

    Periodic maintenance and adjustment 7-18 2 3 4 5 6 7 8 9 5. Install the final transmission oil drain bolt, and then tighten it to the specified torque. 6. Refill with the specified amount of the recommended final transmis- sion oil, and then install and tighten the oil filler cap. Warning! Make sure...

  • Page 62

    Periodic maintenance and adjustment 7-19 1 2 3 4 5 6 7 8 9 3. Remove the coolant reservoir cov- er by removing the screw. 4. Check the coolant level in the cool- ant reservoir. Tip the coolant should be between the minimum and maximum level marks. 5. If the coolant is at or below the minimum level m...

  • Page 63

    Periodic maintenance and adjustment 7-20 2 3 4 5 6 7 8 9 eau34205 air filter elements and check hoses and v-belt case air filter element the air filter elements and the v-belt case air filter element should be ser- viced at the intervals specified in the periodic maintenance and lubrication chart. S...

  • Page 64

    Periodic maintenance and adjustment 7-21 1 2 3 4 5 6 7 8 9 notice: make sure that each filter element is properly seated in its case. Always re- place both air filter elements at the same time, otherwise poor engine performance or damage to the engine may re- sult. The engine should never be operate...

  • Page 65

    Periodic maintenance and adjustment 7-22 2 3 4 5 6 7 8 9 6. Lightly tap the v-belt case air filter element to remove most of the dust and dirt, and then blow out the dirt with compressed air as shown. 7. Check the v-belt case air filter ele- ment for damage and replace it if necessary. 8. Install th...

  • Page 66

    Periodic maintenance and adjustment 7-23 1 2 3 4 5 6 7 8 9 eau21401 valve clearance the valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise. To prevent this from occurring, the valve clearance must be adjusted by a yamaha dealer at the intervals specified in ...

  • Page 67

    Periodic maintenance and adjustment 7-24 2 3 4 5 6 7 8 9 tire inspection the tires must be checked before each ride. If a tire tread shows crosswise lines (minimum tread depth), if the tire has a nail or glass fragments in it, or if the sidewall is cracked, have a yamaha dealer replace the tire imme...

  • Page 68

    Periodic maintenance and adjustment 7-25 1 2 3 4 5 6 7 8 9 eau21992 cast wheels to maximize the performance, durabil- ity, and safe operation of your vehicle, note the following points regarding the specified wheels. ● the wheel rims should be checked for cracks, bends, warpage or damage before each...

  • Page 69

    Periodic maintenance and adjustment 7-26 2 3 4 5 6 7 8 9 there should be no free play at the brake lever ends. If there is free play, have a yamaha dealer inspect the brake system. Warning ewa14211 a soft or spongy feeling in the brake lever can indicate the presence of air in the hydraulic system. ...

  • Page 70

    Periodic maintenance and adjustment 7-27 1 2 3 4 5 6 7 8 9 eau22390 checking the front and rear brake pads the front and rear brake pads must be checked for wear at the intervals spec- ified in the periodic maintenance and lubrication chart. Eau22420 front brake pads each front brake pad is provided...

  • Page 71

    Periodic maintenance and adjustment 7-28 2 3 4 5 6 7 8 9 enter the brake system, possibly caus- ing it to become ineffective. Before riding, check that the brake fluid is above the minimum level mark and replenish if necessary. A low brake fluid level may indicate worn brake pads and/or brake system...

  • Page 72

    Periodic maintenance and adjustment 7-29 1 2 3 4 5 6 7 8 9 eau23093 checking and lubricating the cables the operation of all control cables and the condition of the cables should be checked before each ride, and the ca- bles and cable ends should be lubricat- ed if necessary. If a cable is damaged o...

  • Page 73

    Periodic maintenance and adjustment 7-30 2 3 4 5 6 7 8 9 eau23213 checking and lubricating the centerstand and sidestand the operation of the centerstand and sidestand should be checked before each ride, and the pivots and met- al-to-metal contact surfaces should be lubricated if necessary. Warning ...

  • Page 74

    Periodic maintenance and adjustment 7-31 1 2 3 4 5 6 7 8 9 notice eca10590 if any damage is found or the front fork does not operate smoothly, have a yamaha dealer check or re- pair it. Eau45511 checking the steering worn or loose steering bearings may cause danger. Therefore, the operation of the s...

  • Page 75

    Periodic maintenance and adjustment 7-32 2 3 4 5 6 7 8 9 eau34223 battery the battery is located behind cowling a. (see page 7-8.) this model is equipped with a vrla (valve regulated lead acid) battery. There is no need to check the electro- lyte or to add distilled water. However, the battery lead ...

  • Page 76

    Periodic maintenance and adjustment 7-33 1 2 3 4 5 6 7 8 9 battery damage. ● to charge a vrla (valve regu- lated lead acid) battery, a spe- cial (constant-voltage) battery charger is required. Using a conventional battery charger will damage the battery. If you do not have access to a con- stant-vol...

  • Page 77

    Periodic maintenance and adjustment 7-34 2 3 4 5 6 7 8 9 3. Turn the key to “on” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a yamaha dealer check the electrical system. Eau34240 replacing a headlight bulb this model is...

  • Page 78

    Periodic maintenance and adjustment 7-35 1 2 3 4 5 6 7 8 9 eau24181 tail/brake light this model is equipped with an led-type tail/brake light. If the tail/brake light does not come on, have a yamaha dealer check it. Eau36124 replacing a front turn signal light bulb 1. Place the scooter on the center...

  • Page 79

    Periodic maintenance and adjustment 7-36 2 3 4 5 6 7 8 9 clockwise. 7. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 8. Install the socket (together with the bulb) by turning it clockwise. 9. Place the turn signal light unit in the original position, and...

  • Page 80

    Periodic maintenance and adjustment 7-37 1 2 3 4 5 6 7 8 9 eau34273 replacing the license plate light bulb 1. Place the scooter on the center- stand. 2. Remove cowling b. (see page 7-8.) 3. Remove the license plate light cov- er and license plate light lens by removing the screws. 4. Remove the burn...

  • Page 81

    Periodic maintenance and adjustment 7-38 2 3 4 5 6 7 8 9 heaters or furnaces. Gasoline or gasoline vapors can ignite or ex- plode, causing severe injury or property damage..

  • Page 82

    Periodic maintenance and adjustment 7-39 1 2 3 4 5 6 7 8 9 eau42701 troubleshooting charts starting problems or poor engine performance check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There is no fuel. Check the compression. Supply fuel. The engine does not start. Check the comp...

  • Page 83

    Periodic maintenance and adjustment 7-40 2 3 4 5 6 7 8 9 engine overheating warning ewat1040 ● do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has coo...

  • Page 84

    8-1 1 2 3 4 5 6 7 8 9 scooter care and storage eau37833 matte color caution notice eca15192 some models are equipped with matte colored finished parts. Be sure to consult a yamaha dealer for advice on what products to use be- fore cleaning the vehicle. Using a brush, harsh chemical products or clean...

  • Page 85

    Scooter care and storage 8-2 2 3 4 5 6 7 8 9 cleaning products, solvent or thinner, fuel (gasoline), rust re- movers or inhibitors, brake flu- id, antifreeze or electrolyte. ● do not use high-pressure wash- ers or steam-jet cleaners since they cause water seepage and deterioration in the following a...

  • Page 86

    Scooter care and storage 8-3 1 2 3 4 5 6 7 8 9 can cause loss of control. ● make sure that there is no oil or wax on the brakes or tires. If necessary, clean the brake discs and brake linings with a regular brake disc cleaner or ac- etone, and wash the tires with warm water and a mild deter- gent. ●...

  • Page 87

    Scooter care and storage 8-4 2 3 4 5 6 7 8 9 pedals as well as of the sidestand/ centerstand. 5. Check and, if necessary, correct the tire air pressure, and then lift the scooter so that both of its wheels are off the ground. Alterna- tively, turn the wheels a little every month in order to prevent ...

  • Page 88

    9-1 1 2 3 4 5 6 7 8 9 specifications eau2633p dimensions: overall length: 2230 mm (87.8 in) overall width: 780 mm (30.7 in) overall height: 1380 mm (54.3 in) seat height: 760 mm (29.9 in) wheelbase: 1565 mm (61.6 in) ground clearance: 120 mm (4.72 in) minimum turning radius: 2600 mm (102.4 in) weigh...

  • Page 89

    Specifications 9-2 2 3 4 5 6 7 8 9 operation: centrifugal automatic type chassis: frame type: aluminum die-cast and steel tube back- bone caster angle: 27.00 ° trail: 100.0 mm (3.94 in) front tire: type: tubeless size: 120/80-14m/c 58s manufacturer/model: irc/mb67 manufacturer/model: dunlop/d305fl r...

  • Page 90

    Specifications 9-3 1 2 3 4 5 6 7 8 9 headlight: bulb type: halogen bulb bulb voltage, wattage × quantity: headlight: 12 v, 60 w/55.0 w × 2 tail/brake light: led front turn signal/position light: 12 v, 21 w/5.0 w × 2 rear turn signal light: 12 v, 21.0 w × 2 license plate light: 12 v, 5.0 w × 1 meter ...

  • Page 91

    10-1 2 3 4 5 6 7 8 9 10 consumer information eau26351 identification numbers record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the veh...

  • Page 92

    Consumer information 10-2 1 2 3 4 5 6 7 8 9 10 eau26500 model label the model label is affixed to the inside of the rear storage compartment. (see page 4-14.) record the information on this label in the space provided. This in- formation will be needed when ordering spare parts from a yamaha dealer....

  • Page 93

    Consumer information 10-3 2 3 4 5 6 7 8 9 10 eau26551 reporting safety defects if you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the national highway traffic safety administration (nhtsa) in addition to notifying yam...

  • Page 94

    Consumer information 10-4 1 2 3 4 5 6 7 8 9 10 eau26580 scooter noise regulation tampering with noise control system prohibited: federal law prohibits the following acts or the causing thereof: (1) the removal or rendering inoperative by any person other than for purposes of maintenance, repair, or ...

  • Page 95

    Consumer information 10-5 2 3 4 5 6 7 8 9 10 eau26632 maintenance record copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only...

  • Page 96

    Consumer information 10-6 1 2 3 4 5 6 7 8 9 10 32000 mi (49000 km) or 48 months 36000 mi (55000 km) or 54 months 40000 mi (61000 km) or 60 months maintenance interval date of service mileage servicing dealer name and address remarks.

  • Page 97

    Consumer information 10-7 2 3 4 5 6 7 8 9 10 eau26663 yamaha motor corporation, u.S.A. Street and enduro motorcycle limited warranty a) b) c) d) e) f) 1. 2. Yamaha motor corporation, u.S.A. Hereby warrants that new yamaha motorcycles will be free from defects in material and workmanship for the peri...

  • Page 98

    Consumer information 10-8 1 2 3 4 5 6 7 8 9 10 warranty questions and answers what costs are my responsibility during the warranty period? The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision damages, and oil, oil filters, air ...

  • Page 99

    Consumer information 10-9 2 3 4 5 6 7 8 9 10 eau26750 yamaha extended service (y.E.S.) keep your yamaha protected even after your warranty expires with genuine yamaha extended service (y.E.S.). Y.E.S. Is designed and administered by yamaha motor corporation to provide maximum owner satisfaction. You...

  • Page 100

    Consumer information 10-10 1 2 3 4 5 6 7 8 9 10 we urge you to act now. You’ll get the excellent benefits of trip coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your yamaha limited warranty expires. A special note: if visiting your dealer is...

  • Page 101

    Index a acceleration and deceleration ...................6-2 air filter elements and check hoses and v-belt case air filter element..................7-20 b battery .....................................................7-32 brake fluid, changing ...............................7-28 brake fluid level, c...

  • Page 102

    Index vehicle identification number .................. 10-1 w warranty, extended................................. 10-9 warranty, limited ..................................... 10-7 wheel bearings, checking....................... 7-31 wheels .................................................... 7-25.

  • Page 104

    Printed on recycled paper yamaha motor co., ltd. Printed in japan 2008.5–0.6 × 1 ! (e).