Mixing console table de mixage mischpulte consola de mezcla operation manual manuel d’instructions bedienungsanleitung manual de operación b a 20db peak –16 –60 gain 80 –15 +15 high –15 +15 mid –15 +15 low 0 10 aux 1 0 10 aux 2 0 10 aux 3 0 10 aux 4 l r pan pfl p o s t p r e 10 5 0 5 10 15 20 30 40 ...
Introduction thank you for purchasing a yamaha mx200 mixing console. The mx200 series provides an excellent balance of operability, functionality and ease of use. In order to take full advantage of the mx200’s capabilities and enjoy years of trouble-free use, please read this manual carefully. Featu...
1 precautions 1. Avoid excessive heat, humidity, dust and vibration keep the unit away from locations where it is likely to be exposed to high temperatures or humidity — such as near radiators, stoves, etc. Also avoid locations which are subject to excessive dust accumulation or vibration which coul...
2 control panel ■ channel control section 1 input selector this button selects the input connector for the channel. When a ( ) is selected, the input signal will be taken from the rear panel input a connector (balanced xlr type). When b ( ) is selected, the input signal will be taken from the rear p...
3 7 aux1–4 controls these knobs control the level of the signals sent to the aux buses. • the aux1 and aux2 controls are pre-fader, and the signal levels sent to the aux 1 and 2 buses will be un- affected by the channel fader setting. • the aux3 and aux 4 controls are post-fader, and the signal leve...
4 ■ master control section 1 stereo on switch this switch turns the st out output on/off. When this switch is off, levels will not be displayed in the st meters. The mono out signal will be sent regardless of this switch. 2 stereo l, r master faders these faders adjust the final level of the combine...
5 this knob is a high frequency equalizer that provides 12khz shelving equalization of the signal input at aux return. 1 +4db aux return aux 1 level inv eq 2band eq 2band high low r l inv sum 9 rec out control this knob adjusts the output level of the rec out jacks (connector 5) connected to a tape ...
6 ■ connectors input a input b out in input ch insert i/o 0db out in 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 –10db r r l l 1r 1l/mono 2r 2l/mono 3 1 4 2 l r +4db –10db tape in rec out stereo out +4db aux return +4db aux send +4db mono out 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 microphone cables and microphones c...
7 8 aux send (1, 2, 3, 4) these are unbalanced jacks with a nominal output and im- pedance of +4db/600 Ω . (aux 1 and 2 are pre-fader, and aux 3 and 4 are post-fader.) 9 aux return (1l/mono, 1r, 2l/mono, 2r) these are unbalanced jacks with a nominal input level and impedance of +4db/10 k Ω . These j...
8 mixing console stereo out aux send1 88 mic and line input 88 aux rtn2 aux rtn1 aux send4 aux send3 aux send2 cassette deck or dat tape in rec out stage monitors front of house main speakers power amp power amp graphic eq headphone effects processor application example.
9 specifications ■ general specifications maximum output level +24db (stereo l/r) @600 Ω , 0.5% thd at 1khz +24db (mono out) @600 Ω , 0.5% thd at 1khz +20db (aux send) @600 Ω , 0.5% thd at 1khz total harmonic distortion (st l/r, mono, aux send @600 Ω ) frequency response 20hz–20khz +1db, –2db (st l/...
10 dimensions (w × h × d) 449 × 124.6 × 461.7 mm mx200-8 569 × 124.6 × 461.7 mm mx200-12 689 × 124.6 × 461.7 mm mx200-16 929 × 124.6 × 461.7 mm mx200-24 weight 9.5kg mx200-8 11kg mx200-12 13.5kg mx200-16 17kg mx200-24 0db=0.775 vrms ■ input specifications input connectors input impedance nominal imp...
11 ■ block and level diagrams pad off pad on (db) (db) -70 -60 -50 -40 -30 -20 -10 aux send st mono 0 +10 aux stereo tape in aux return gain min gain min pad on gain max pad off gain max -70 -60 -50 -40 -30 -20 -10 0 +10 on meter meter meter meter meter select (aux send 4) (phones) (aux send 3) (mon...
12 w 897 657 537 417 929 689 569 449 wi mx200-12 mx200-24 mx200-16 mx200-8 model d: 461.7 w wi (54.5) (54.5) h: 124.6 57.3 295 54.5 8 101.2 80.6 ■ dimensions units: mm.
Français table de mixage manuel d’instructions.
Introduction nous vous remercions d’avoir fait l’acquisition d’une console de mixage mx200 yamaha. La série mx200 apporte un excellent équilibre entre fonctionnalité et facilité d’emploi. Afin de tirer pleine- ment partie des possibilités du mx200 et de garantir des années d’utilisation sans problèm...
1 précautions 1. Evitez tout emplacement excessivement chaud, hu- mide, poussiéreux ou soumis à des vibrations ne placez pas l’appareil dans un endroit où il risque d’être exposé à des températures élevées ou une forte humidité (évitez la proximité de radiateurs, poêles, etc). Evitez éga- lement les...
2 panneau de commande ■ section de contrôle de canal 1 sélecteur d’entrée cette touche sélectionne le connecteur d’entrée du canal. Lorsque a ( ) est sélectionné, le signal d’entrée est pris à partir du connecteur d’entrée a (input a) (type xlr symétrique) du panneau arrière. Lorsque b ( ) est sélec...
3 7 commandes auxiliaires (aux1–4) ces commandes contrôlent le niveau des signaux envoyés aux bus aux. • les commandes aux1 et aux2 sont pour les pré- faders, et les niveaux de signaux envoyés aux bus aux 1 et aux 2 bus ne sont pas affectés par le réglage de fader du canal. • les commandes aux3 et a...
4 ■ section de contrôle principale 0 10 phones –15 +15 high –15 +15 low 0 10 aux 1 0 10 level 0 10 rec out 0 10 tape in aux return 1 aux return 2 l st r phones mono on afl afl afl afl afl aux send 4 aux send 3 aux send 2 aux send 1 meter select l st r 1 aux 2 mono pfl/afl 3 aux 4 +6 +4 +2 0 –2 –4 –7...
5 9 commande de sortie d’enregistrement (rec out) cette commande ajuste le niveau de sortie des prises de sortie d’enregistrement (rec out) (connecteur 5 con- necté à une platine cassette, etc. 0 commande d’entrée cassette (tape in) cette commande ajuste le volume de contrôle d’une pla- tine cassett...
6 ■ connecteurs input a input b out in input ch insert i/o 0db out in 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 –10db r r l l 1r 1l/mono 2r 2l/mono 3 1 4 2 l r +4db –10db tape in rec out stereo out +4db aux return +4db aux send +4db mono out 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 connexions des microphones et de l...
7 les fils cavaliers internes peuvent être changés pour dépla- cer le signal de sortie mono (mono out) de façon à ce qu’il soit pris après le fader stéréo (st). Si on veut effec- tuer cette modification, consulter votre revendeur. On on r l stereo out mono out inv inv sum sum sum inv inv on on r l s...
8 mixing console retours de scène haut-parleurs de salle amplificateur amplificateur casque stereo out 88 88 aux rtn2 aux rtn1 aux send4 aux send3 platine à bobines, dat tape in rec out equaliseur graphique entrées ligne et micro processeur d’effets aux send1 aux send2 exemple d’application.
9 caractéristiques ■ caractéristiques générales niveau de sortie maximum +24db (stereo l/r) @ 600 Ω , dht 0,5 % à 1khz +24db (mono out) @ 600 Ω , dht 0,5 % à 1khz +20db (aux send) @ 600 Ω , dht 0,5 % à 1khz distorsion harmonique totale (st l/r, mono, aux send @ 600 Ω ) réponse en fréquence 20hz–20kh...
10 modèle général mx200-8 230v ca 50hz 45w, mx200-12 230v ca 50hz 55w mx200-16 230v ca 50hz 65w, mx200-24 230v ca 50hz 80w modèle britannique mx200-8 240v ca 50hz 45w, mx200-12 240v ca 50hz 55w mx200-16 240v ca 50hz 65w, mx200-24 240v ca 50hz 80w dimensions (w × h × d) 449 × 124.6 × 461.7 mm mx200-8...
11 ■ schémas de connexions et de niveaux pad off pad on (db) (db) -70 -60 -50 -40 -30 -20 -10 aux send st mono 0 +10 aux stereo tape in aux return gain min gain min pad on gain max pad off gain max -70 -60 -50 -40 -30 -20 -10 0 +10 on meter meter meter meter meter select (aux send 4) (phones) (aux s...
12 w 897 657 537 417 929 689 569 449 wi mx200-12 mx200-24 mx200-16 mx200-8 model d: 461.7 w wi (54.5) (54.5) h: 124.6 57.3 295 54.5 8 101.2 80.6 ■ dimensions unité: mm.
Deutsch mischpulte bedienungsanleitung bescheinigung des importeurs hiermit wird bescheinigt, daß der / die / das mixing console, typ: mx200-8 mx200-12 mx200-16 mx200-24 (gerät, typ, bezeichnung) in Übereinstimmung mit den bestimmungen der 82/499/ewg (eg-richtlinie) funkentstört ist. Der deutschen b...
Einleitung vielen dank für den kauf des yamaha mischpults mx200. Die mischpulte der mx200 serie zeich- nen sich durch eine praktische anordnung, vielseitige funktionen sowie eine einfache bedienung aus und erlauben zahlreiche anwendungsmöglichkeiten. Um das große leistungspotential des mx200 voll au...
1 vorsichtsmaßnahmen 1. Meiden sie extreme temperaturen, starke feuchtig- keit, staub und vibrationen stellen sie das pult niemals an einen extrem warme oder feuchten ort – also niemals in die nähe eines heizkörpers, ofens usw. Meiden sie außerdem staubige orte sowie orte, an denen das pult starken ...
2 bedienkonsole ■ eingangskanal-bedienfeld 1 eingangsbuchsen-wahlschalter (a/b) dieser schalter dient zur wahl der eingangsbuchse für den betreffenden kanal. Bei ausgerastetem schalter ( a) wird das eingangssignal über die symmetrische xlr-eingangsbuchse (input a) auf der geräterückseite empfangen. ...
3 7 aux-senderegler (aux 1–4) mit diesen reglern können sie das eingangssignal den vier aux-sammelschienen zuweisen und gleichzeitig den sendepegel bestimmen. • die senderegler aux1 und aux2 nehmen das signal vor dem kanalfader auf, weshalb sich die stellung des kanalfaders nicht auf den sendepegel ...
4 ■ mischkonsole 0 10 phones –15 +15 high –15 +15 low 0 10 aux 1 0 10 level 0 10 rec out 0 10 tape in aux return 1 aux return 2 l st r phones mono on afl afl afl afl afl aux send 4 aux send 3 aux send 2 aux send 1 meter select l st r 1 aux 2 mono pfl/afl 3 aux 4 +6 +4 +2 0 –2 –4 –7 –10 –15 –20 –00 +...
5 9 aufnahmepegelregler (rec out) dieser regler bestimmt den ausgangspegel an den rec out-buchsen (anschluß 5), die für den anschluß von bandgeräten usw. Vorgesehen sind. 0 bandwiedergabe-pegelregler (tape in) der tape in-regler stellt den eingangspegel für die si- gnale eines bandgeräts usw. Ein, d...
6 ■ anschlüsse input a input b out in input ch insert i/o 0db out in 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 –10db r r l l 1r 1l/mono 2r 2l/mono 3 1 4 2 l r +4db –10db tape in rec out stereo out +4db aux return +4db aux send +4db mono out 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 1 eingangsbuchsen input a hierbei h...
7 durch umsetzen von internen Überbrückungen kann der signalabgriff für das mono out-signal hinter die ste- reo-fader versetzt werden. Falls sie dies wünschen, wen- den sie sich bitte an ihren händler. On on r l stereo out mono out inv inv sum sum sum inv inv on on r l stereo out mono out inv inv su...
8 anwendungsbeispiel mikrofon- und line-eingänge mixing console stereo out 88 88 aux rtn2 aux rtn1 aux send4 aux send3 tonbandgerät, dat tape in rec out bühnenmonitore saalbeschallung endstufe endstufe graphischer equalizer kopfhörer außenbordeffektgerät aux send1 aux send2.
9 spezifikationen ■ allgemeine spezifikationen max. Ausgangspegel +24db (stereo l/r) bei 600 Ω , 0,5% klirrfaktor bei 1khz +24db (mono out) bei 600 Ω , 0,5% klirrfaktor bei 1khz +20db (aux send) bei 600 Ω , 0,5% klirrfaktor bei 1khz klirrfaktor (st l/r, mono, aux send bei 600 Ω ) frequenzgang 20hz –...
10 abmessungen (w × h × d) 449 × 124.6 × 461.7 mm mx200-8 569 × 124.6 × 461.7 mm mx200-12 689 × 124.6 × 461.7 mm mx200-16 929 × 124.6 × 461.7 mm mx200-24 gewicht 9.5kg mx200-8 11kg mx200-12 13.5kg mx200-16 17kg mx200-24 0db=0.775 vrms ■ eingangsdaten eingangsbuchsen eingang nennim- eingangspegel ans...
11 ■ blockschaltbild und pegeldiagramm pad off pad on (db) (db) -70 -60 -50 -40 -30 -20 -10 aux send st mono 0 +10 aux stereo tape in aux return gain min gain min pad on gain max pad off gain max -70 -60 -50 -40 -30 -20 -10 0 +10 on meter meter meter meter meter select (aux send 4) (phones) (aux sen...
12 w 897 657 537 417 929 689 569 449 wi mx200-12 mx200-24 mx200-16 mx200-8 model d: 461.7 w wi (54.5) (54.5) h: 124.6 57.3 295 54.5 8 101.2 80.6 ■ abmessungen einheit: mm.
Español consola de mezcla manual de operación.
Introducción gracias por su compra de la consola de mezclas yamaha mx200. La serie mx200 proporciona un equilibrio excelente entre operabilidad, funcionalidad y facilidad de uso. Si desea obtener las máximas ventajas de las prestaciones de su mx200 y disfrutar durante años de un funcionamiento sin p...
1 precauciones 1. Evite un exceso de calor, humedad, polvo o vibraciones. Mantenga el aparato alejado de lugares donde pueda quedar expuesto a elevadas temperaturas o grados de humedad, como por ejemplo cerca de radiadores, estufas, etc. Evite también los lugares que estén sometidos a una excesiva a...
2 panel de control ■ sección de control de canales 1 selector de entrada este botón selecciona el conector de entrada para el canal. Cuando se selecciona a ( ), se tomará la señal de entrada del conector de entrada a (input a) del panel trasero (tipo xlr simétrico). Cuando se selecciona b ( ), se to...
3 7 controles auxiliares 1–4 (aux 1–4) estos mandos controlan el nivel de las señales enviadas hacia los buses auxiliares (aux). • los controles auxiliares 1 y 2 (aux 1, aux 2) son controles pre-atenuador, y los niveles de las señales enviados hacia los buses auxiliares 1 y 2 no se verán afectados p...
4 ■ sección de control principal 1 interruptor de encendido del estéreo (stereo on) este interruptor enciende y apaga la salida estereofónica (st out). Cuando este interruptor está apagado, no se visualizarán los niveles en los medidores estereofónicos (st). La señal de la salida monoaural se enviar...
5 este mando es un equalizador de alta frecuencia que facilita una equalización de declive de 12khz de la entrada de señal hacia los retornos auxiliares (aux return). 1 +4db aux return aux 1 level inv eq 2band eq 2band high low r l inv sum 9 control salida de grabación (rec out) este mando ajusta el...
6 ■ conectores input a input b out in input ch insert i/o 0db out in 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 –10db r r l l 1r 1l/mono 2r 2l/mono 3 1 4 2 l r +4db –10db tape in rec out stereo out +4db aux return +4db aux send +4db mono out 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 1 entrada a (input a) son conectore...
7 8 envíos auxiliares (1, 2, 3, 4) (aux send, 1, 2, 3, 4) se trata de tomas no simétricas que tienen una salida nominal e impedancia nominal de +4db/600 Ω . (los envíos auxiliares 1 y 2 son pre-atenuador y los 3 y 4 son post-atenuador). 9 retornos auxiliares (aux return) (1l/mono, 1r, 2l/mono, 2r) s...
8 micrófonos, línea entradas mixing console stereo out 88 88 aux rtn2 aux rtn1 aux send4 aux send3 platina de cinta o dat tape in rec out monitores de escenario altavoces principales frente al edificio amplificador de potencia amplificador de potencia ecualizador gráfico auriculares procesador de ef...
9 especificaciones ■ especificaciones generales nivel máximo de salida +24db (stereo l/r) @600 w, 0,5% dat a 1khz +24db (mono out) @600 w, 0,5% dat a 1khz +20db (aux send) @600 w, 0,5% dat a 1khz distorsión armónica total (st l/r, mono, aux send @600 Ω ) respuesta en frecuencia 20hz-20khz +1db, –2db...
10 general mx200-8 230v ca 50hz 45w, mx200-12 230v ca 50hz 55w mx200-16 230v ca 50hz 65w, mx200-24 230v ca 50hz 80w gran bretaña mx200-8 240v ca 50hz 45w, mx200-12 240v ca 50hz 55w mx200-16 240v ca 50hz 65w, mx200-24 240v ca 50hz 80w dimensiones (w × h × d) 449 × 124.6 × 461.7 mm mx200-8 569 × 124.6...
11 ■ diagramas de bloque y de nivel pad off pad on (db) (db) -70 -60 -50 -40 -30 -20 -10 aux send st mono 0 +10 aux stereo tape in aux return gain min gain min pad on gain max pad off gain max -70 -60 -50 -40 -30 -20 -10 0 +10 on meter meter meter meter meter select (aux send 4) (phones) (aux send 3...
12 w 897 657 537 417 929 689 569 449 wi mx200-12 mx200-24 mx200-16 mx200-8 model d: 461.7 w wi (54.5) (54.5) h: 124.6 57.3 295 54.5 8 101.2 80.6 ■ dimensions unidades: mm.
Yamaha corporation r0 1 ip printed in korea p.O.Box 1, hamamatsu, japan.