1. DL manuals
  2. Yamaha
  3. Home Cinema speakers
  4. NS-P300
  5. Owner's Manual

Yamaha NS-P300 Owner's Manual

Manual is about: Home Cinema Speaker Package

Summary of NS-P300

  • Page 1

    Home cinema speaker package systeme d ’enceintes home cinema ns-p300 active servo technology u c a contents safety instructions ...............................2 profile of this system .........................3 caution ........................................................4 supplied accessories .....

  • Page 2: Safety Instructions

    2 1 read instructions – all the safety and operating instructions should be read before the unit is operated. 2 retain instructions – the safety and operating instructions should be retained for future reference. 3 heed warnings – all warnings on the unit and in the operating instructions should be ...

  • Page 3: Profile of This System

    3 english 1. Important notice : do not modify this unit! This product, when installed as indicated in the instructions contained in this manual, meets fcc requirements. Modifications not expressly approved by yamaha may void your authority, granted by the fcc, to use the product. 2. Important : when...

  • Page 4: Supplied Accessories

    4 ● to assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. ● install the speakers in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers...

  • Page 5: Speaker Configuration

    5 english before you make connections, place all speakers in their proper positions respectively. The positioning of speakers is important, because it controls the whole sound quality of this system. Position the speakers based on your listening position by following instructions in this section. Sp...

  • Page 6

    6 ■ mounting the center speaker place the center speaker on the tv, on the floor under the tv or in the tv rack so that it is stabilized. When placing the speaker on top of the tv, to prevent the speaker from falling down, put the provided velcro strips at two points on both bottom of the speaker an...

  • Page 7

    7 english ■ mounting the effect speakers mount the effect speakers on a shelf, rack or floor, or hang them on the wall. To mount the effect speakers on a wall mount the speakers in either of the two configurations shown in the following figures by using the holes provided on the speakers’ rear panel...

  • Page 8: Connections

    8 • connect the speakers to the speaker output terminals of your amplifier with the provided speaker cords. • connect the speakers making sure not to reverse the polarity (+, –). Connect the (+) terminals on both the amplifier and the speakers using one side of the cord. Connect the (–) terminals on...

  • Page 9: Good

    9 english for connections, keep the speaker cords as short as possible. Do not bundle or roll up an excess of the cords. If the connections are faulty, no sound will be heard from the speakers. How to connect: ➀ press and hold the terminal’s tab, as shown in the figure. ➁ insert the bare wire end pr...

  • Page 10

    10 if your amplifier has only one set of main speaker output terminals output to speakers input1 from amplifier output to speakers input1 from amplifier input2 high cut auto standby standby-red on-green off low high off power on low high volume 0 10 amplifier to ac outlet connect the speaker output ...

  • Page 11

    11 english • to connect with a yamaha dsp amplifier (or av receiver), connect the low pass (or subwoofer etc.) terminal on the rear of the dsp amplifier (or av receiver) to either the left (l) or right (r) input2 terminal of the subwoofer. • to connect the subwoofer to the split subwoofer terminals ...

  • Page 12: Controls and Their Functions

    12 1 output (to speakers) terminals can be used for connections with the main speakers. These terminals output signals sent from the amplifier to the main speakers directly. 2 input1 (from amplifier) terminals used to connect this unit with the speaker terminals of the amplifier. 3 input2 terminals ...

  • Page 13: 1, 4

    13 english 1 set the volume control to minimum. 2 turn on the power supply to all the components. 3 play any source and adjust the amplifier’s volume control to the desired listening level. 4 increase the volume gradually to adjust the volume balance between this unit and the main speakers. 5 if nec...

  • Page 14

    14 the theory of active servo technology is based upon two major factors, the helmholtz resonator and negative- impedance drive. Active servo processing speakers reproduce the bass frequencies through an “air woofer”, which is a port or opening in the speaker’s cabinet. This opening is used instead ...

  • Page 15: Troubleshooting (For Sw-P30)

    15 english symptom power is not supplied even though the power switch is set to the on position. No sound. Sound level is too low. This unit will not turn on automatically. This unit turns into the standby mode unexpectedly. This unit turns on unexpectedly. Cause the power plug is not securely conne...

  • Page 16: Specifications

    16 ns-m103, ns-c103, ns-e103 > type ns-m103 > ........2-way acoustic-suspension speaker system magnetic shielding type ns-c103 > ......2-way 3-speaker bass-reflex speaker system magnetic shielding type ns-e103 > .................Full-range bass-reflex speaker system magnetic shielding type speaker u...

  • Page 17

    Yamaha electronics corporation, usa 6660 orangethorpe ave., buena park, calif. 90620, u.S.A. Yamaha canada music ltd. 135 milner ave., scarborough, ontario m1s 3r1, canada yamaha electronik europa g.M.B.H. Siemensstr. 22-34, 25462 rellingen bei hamburg, f.R. Of germany yamaha electronique france s.A...