Power amplifier owner’s manual mode d’emploi bedienungsanleitung manual de instrucciónes temp protection power on off a b clip signal –db ∞ 0 ∞ 0 40 30 20 15 10 3 6 25 40 30 20 15 10 3 6 25 eeengine m.
Introduction english thank you for purchasing a yamaha p4500/3200/1600 series power amplifier. This series of audio amps was developed from yamaha's wealth of experience in building pa equipment and its tradition of careful attention to every detail of circuit design. These amps feature high power a...
Precautions 1. Avoid excessive heat, humidity, dust and vibration. Keep the unit away from locations where it is likely to be exposed to high temperatures or humidity — such as near radiators, stoves, etc. Also avoid locations which are subject to excessive dust accumulation or vibration which could...
2 controls and functions ■ front panel temp protection power on off a b clip signal 6 1 2 3 4 5 –db ∞ 0 ∞ 0 40 30 20 15 10 3 6 25 40 30 20 15 10 3 6 25 eeengine 1 power switch and indicator this is the main power switch. Press to power on the amplifier. Press again to power off. The power indicator ...
3 ■ rear panel input speakers channel b channel a channel b channel a g g (bridge) (parallel) bridge stereo parallel stereo bridge max. Output 450w/4 Ω (stereo) max. Output 900w/8 Ω (bridge) (stereo) 4-8 Ω /sp (bridge) 8-16 Ω /sp 3 2 1 4 3 speakers terminals for polarity in each mode, refer to the f...
4 ■ modes: stereo/parallel/bridge bridge mode in this mode, the channel a input signal will be output from the bridge output jacks. In this case, use the front panel (channel) a volume control to adjust the volume. ■ speaker impedance in stereo and parallel modes, the minimum load (=speaker) impedan...
5 caution for speaker connection 1. Turn off the power switch. 2. Remove the cover attachment screw(s) and remove the protective cover from the speaker terminals. Screw 3. After removing approx. 10 mm of insulation from the ends of the speaker cables, pass the bare ends of the speaker wires through ...
6 rack mounting ■ mounting in an eia standard rack if multiple high-power amp units are mounted in a rack with poor ventilation, the heat from the amps will cause the interior of the amp to become very hot, causing the performance of the amps to be impaired. When mounting amps in a rack, you must ma...
7 ■ portable rack mounting the amplifier intakes cool air through the front panel and exhausts warm air out the rear panel. When mounting amplifiers in a portable rack, make sure the rear panel is completely open for ventilation. Front air intake air exhaust completely open (rear view) (side view) i...
8 specifications ■ general specifications p4500 p3200 p1600 power output level (rated power) 8 Ω /stereo 460 w + 460 w 340 w + 340 w 160 w + 160 w 20 hz~20 khz 4 Ω /stereo 620 w + 620 w 440 w + 440 w 200 w + 200 w 0.05% 8 Ω /bridge 1240 w 880 w 400 w 1 khz 8 Ω /stereo 520 w + 520 w 370 w + 370 w 175...
9 ■ block diagram temperature channel b channel a clip clip signal bch power amp pc limiter ach power amp pc limiter speakers (bridge) (parallel) channel a channel b b a input protection temp (heat sink) sensor circuit protection stereo parallel bridge g g signal ■ dimensions 15.5 61.2 292 55.2 308 ...
10 ■ performance graphs mode:stereo both ch driven rl=4 Ω , f=1khz mode:stereo both ch driven rl=4 Ω , f=1khz mode:stereo both ch driven rl=4 Ω , f=1khz p1600 p3200 p4500 output power [w] power consumption [w] power consumption [w] output power [w] output power [w] power consumption [w] 1k 100 10 1 ...
