Yamaha P50-m Owner's Manual - page 40
31
SOUND LISTS & MIDI DATA
E ff e c t L i s t s
Effect Type List
REVERB
Exclusive
Effect Type
Description
MSB
LSB
0
0
NO EFFECT
Effect turned off.
1
0
HALL1
Reverb simulating the resonance of a hall.
1
1
HALL2
Reverb simulating the resonance of a hall.
2
0
ROOM1
Reverb simulating the resonance of a room.
2
1
ROOM2
Reverb simulating the resonance of a room.
2
2
ROOM3
Reverb simulating the resonance of a room.
3
0
STAGE1
Reverb appropriate for a solo instrument.
3
1
STAGE2
Reverb appropriate for a solo instrument.
4
0
PLATE
Reverb simulating a metal plate reverb unit.
10
0
WHITE ROOM
A unique short reverb with a bit of initial delay.
11
0
TUNNEL
Simulation of a tunnel space expanding to left and right.
13
0
BASEMENT
A bit of initial delay followed by reverb with a unique resonance.
CHORUS
Exclusive
Effect Type
Description
MSB
LSB
0
0
NO EFFECT
Effect turned off.
41
0
CHORUS1
Conventional chorus program that adds natural spaciousness.
41
1
CHORUS2
Conventional chorus program that adds natural spaciousness.
41
2
CHORUS3
Conventional chorus program that adds natural spaciousness.
41
8
CHORUS4
Chorus with stereo input. The pan setting specified for the Part will also apply to the effect sound.
42
0
CELESTE1
A 3-phase LFO adds modulation and spaciousness to the sound.
42
1
CELESTE2
A 4-phase LFO adds modulation and spaciousness to the sound.
42
2
CELESTE3
A 5-phase LFO adds modulation and spaciousness to the sound.
42
8
CELESTE4
CELESTE with stereo input. The pan setting specified for the Part will also apply to the effect sound.
43
0
FLANGER1
Adds a jet-airplane effect to the sound.
43
1
FLANGER2
Adds a jet-airplane effect to the sound.
43
8
FLANGER3
Adds a jet-airplane effect to the sound.
MSB and LSB values are in hexadecimal. *LSB=0 selects the basic type.
WHITE ROOM, TUNNEL, BASEMENT
N o .
Parameter
Range
Value
→
P 3 2 * * Control
1
Reverb Time
0.3~30.0s
0-69
table#4
2
Diffusion
0~10
0-10
3
Initial Delay
0~63
0-63
table#5
4
HPF Cutoff
Thru~8.0kHz
0-52
table#3
5
LPF Cutoff
1.0k~Thru
34-60
table#3
6
Width
0.5~10.2m
0-37
table#11
7
Heigt
0.5~20.2m
0-73
table#11
8
Depth
0.5~30.2m
0-104
table#11
9
Wall Vary
0~30
0-30
10
Dry/Wet
D63>W~D=W~D 1-127 ● 11 Rev Delay 0~63 0-63 table#5 12 Density 0~3 0-3 13 Er/Rev Balance E63>R~E=R~E 1-127 14 15 Feedback Level –63~+63 1-127 16 CHORUS1,2,3,4, CELESTE1,2,3,4 N o . Parameter Range Value → P 3 2 * * Control 1 LFO Frequency 0.00~39.7Hz 0-127 table#1 2 LFO PM Depth 0~127 0-63 3 Feedback Level –63~+63 1-127 4 Delay Offset 0~12a7 0-127 table#2 5 6 EQ Low Frequency 50Hz~2.0kHz 8-40 table#3 7 EQ Low Gain –12~+12dB 52-76 8 EQ High Frequency 500Hz~16.0kHz 28-58 table#3 9 EQ High Gain –12~+12dB 52-76 10 Dry/Wet D63>W~D=W~D 1-127 ● 11 12 13 14 15 Input Mode mono/stereo 0-1 16 Effect Parameter List FLANGER1,2,3 N o . Parameter Range Value → P 3 2 * * Control 1 LFO Frequency 0.00~39.7Hz 0-127 table#1 2 LFO Depth 0~127 0-127 3 Feedback Level –63~+63 1-127 4 Delay Offset 0~63 0-63 table#2 5 6 EQ Low Frequency 50Hz~2.0kHz 8-40 table#3 7 EQ Low Gain –12~+12dB 52-76 8 EQ High Frequency 500Hz~16.0kHz 28-58 table#3 9 EQ High Gain –12~+12dB 52-76 10 Dry/Wet D63>W~D=W~D 1-127 ● 11 12 13 14 LFO Phase Difference –180~+180deg 4-124 resolution = 15 30deg. 16 HALL1,HALL2, ROOM1,ROOM2,ROOM3, STAGE1,STAGE2, PLATE N o . Parameter Range Value → P 3 2 * * Control 1 Reverb Time 0.3~30.0s 0-69 table#4 2 Diffusion 0~10 0-10 3 Initial Delay 0~63 0-63 table#5 4 HPF Cutoff Thru~8.0kHz 0-52 table#3 5 LPF Cutoff 1.0k~Thru 34-60 table#3 6 7 8 9 10 Dry/Wet D63>W~D=W~D 1-127 ● 11 Rev Delay 0~63 0-63 table#5 12 Density 0~3 0-3 13 Er/Rev Balance E63>R~E=R~E 1-127 14 High Damp 0.1~1.0 1-10 15 Feedback Level –63~+63 1-127 16 ● : Indicates that AC1 (Assignable Controller 1) can be used to control the parameter value. No.*: Corresponds to parameter number given in Appended Table 1-3 on page 38. → P32**: Refer to the Effect-Data Assignment Table.