Yamaha RS-75 Assembling Instructions

RS75

ASSEMBLY INSTRUCTIONS

◆ Cable Band

 (x10)

◆ Assembly Instructions 

(this sheet)

◆ Overall Assembly RS75

(When the box is opened)

◆ Small Screws M5 X 8

(Module Holder Fixing Screws X4)

■ Handling Precautions

• Do not alter the product. Doing so may result in damage or deterioration to the product.

• Do not step on or place heavy objects on the product. It may result in damage.

• Do not use or keep the product in places with extremely high temperature (places in direct sun-

light, close to a heater, in a closed car, etc.) or damp (bathroom, outside on a rainy day, etc.). It

may result in deformation, discoloration, stickiness, damage or deterioration.

• To clean the product, please wipe with a soft cloth or a damp cloth that has been wrung out

thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a

damp cloth that has been wrung out thoroughly to remove any remaining detergent. Do not use

benzine, thinner or alcohol as it may result in discoloration or deformation. Also pay close atten-

tion so as not to let the water and detergent come into contact with the cushions used in the

product, it may result in deterioration.

Before using, please read this “Assembly In-

struction” sheet, and use this product in a safe

and proper manner.

Especially for children, parents or an instructor

should teach the children the proper manner in

which to use the device.

PRECAUTIONS

Always set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the

instrument being unstable and overturning.

Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury.

When adjusting the height or angle, do not suddenly loosen the bolt. The pad may drop, the rack or pipes may slip, pinching or

causing injury to hands or fingers.

Do not sit or step on the rack. The rack may overturn or be damaged resulting in injury.

Please be careful when children are close to or touching the product. The product has many pipes and arms so careless

movement around the product may result in injury.

When setting the pads and modules, please pay close attention in regards to the handling and setting of cables. Feet may

become entangled in the cables resulting in falls.

Do not put your hands or feet under the foot pedal or foot switch. They may be pinched resulting in injury.

Watch your fingers when adjusting clamps. They may become pinched resulting in injury.

Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers.

Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury.

Caution (including danger, or warning). This

mark indicates cautions in which you should

pay close attention to.

Acts indicated with this icon are prohibited and

should not be attempted.

To prevent against accidents and injury

Please follow the cautions listed below

* Specifications are subject to change without notice.

If this symbol is ignored and the equipment is used improperly, fatal injury to per-

sons or serious damage could occur.

WARNING

CAUTION

If this symbol is ignored and the equipment is used improperly, there is a danger

of injury to persons handling the equipment, and material damage could occur.

■ RS75 Assembly

* Parts for the RS75's main structure have already been assembled before packing. After removing the unit from the box, follow the instructions described below to complete the assembly.

A Phillips (+) screwdriver is required when attaching the Drum Trigger Module. Please prepare one before starting assembly.

After removing the unit from the box, remove all cushion material.

1

2

Setting up the parts

• Loosen the wing bolts, slide the pipes out a little, and attach the rubber feet.

• Loosen the bolts on the movable arms and legs, as shown in the diagrams

below, then secure the bolts firmly once setting is complete.

Follow the setup order (q~i) in the diagrams shown below.

q

w

e

←Caution

Left Leg Assembly

Right Leg Assembly

Module Holder Assembly

←Caution

y

r

t

u

Cymbal Holder

Side Arm (L) Assembly

Side Arm (R) Assembly

Attaching the Drum Trigger Module

3

3-1

Remove the module holder from the holder clamp,

and use the supplied screws to attach the Drum

Trigger Module.

Make sure only the supplied screws are

used. Using any other screws may result

in the unit falling off the holder or damage.

3-2

Reattach the module holder to the holder clamp.

Caution

: Make sure the bolts marked with a "         " are loosened before setting up.

INTRODUCTION

Thank you for purchasing the Yamaha Electronic Drum Rack System RS75.

Before using, thoroughly read these assembly instructions, and use this product

safely and correctly.

i

Cymbal Holder

■ Inside This Package

Before setup, please make sure that all of the items listed below are present and ac-

counted for. If anything is missing, please contact the dealer from whom you purchased

the unit.

◆ Rubber Foot

(x2)

Rubber Foot

Rubber Foot

Loosen

Loosen

Loosen

Loosen

Be careful around the pipe edges.

The cut pipe ends are sharp and can

injure your fingers.