Yamaha S08 Voice Editor Data List - page 21
21
1.7
Polyphonic aftertouch (Receive only)
This message conveys the pressure that is applied to the keyboard after playing a note (for
individual note numbers).
The pressure can be controlled independently for each note. This message will affect
currently-sounding notes.
The effect of this message is determined by the following Multi Part parameters.
1. PAT PITCH CONTROL
2. PAT FILTER CONTROL
3. PAT AMPLITUDE CONTROL
4. PAT LFO PMOD DEPTH
5. PAT LFO FMOD DEPTH
6. PAT LFO AMOD DEPTH
By default, there will be no effect.
The effect will apply to note numbers 36...97.
In the case of either of the following Multi Part parameter settings, that part will not receive
Polyphonic Aftertouch.
• RECEIVE CHANNEL AFTER TOUCH = OFF
• PART MODE = DRUM, DRUMS1, 2
2.
System exclusive messages
2.1
Parameter changes
This devices uses the following parameter changes.
[UNIVERSAL REALTIME MESSAGE]
1) Master Volume
2) Master Fine Tuning
3) Master Coarse Tuning
4) Global Parameter Control
1) Reverb Parameter
2) Chorus Parameter
5) Controller Destination Setting
1) Channel Pressure (After Touch)
2) Control Change
6) Key-Based Instrument Controllers
[UNIVERSAL NON REALTIME MESSAGE]
1) General MIDI System On
2) General MIDI 2 System On
3) General MIDI Off
4) Scale/Octave Tuning
5) Identity Request (INQUIRY MESSAGE)
6) Identity Reply (INQUIRY MESSAGE)
[XG PARAMETER CHANGE]
1) XG System on
2) XG System parameter change
3) Multi Effect1 parameter change
4) Multi Part parameter change
5) Drums Setup parameter change
[NATIVE PARAMETER CHANGE]
1) Native System parameter change
2) Remote Switch parameter change
3) Normal Voice parameter change
4) Drum Voice parameter change
[Others]
1) Master tuning
2.1.1 Universal realtime messages
2.1.1.1 Master Volume
11110000
F0H
= Exclusive status
01111111
7FH
= Universal Real Time
01111111
7FH
= ID of target device
00000100
04H
= Sub-ID #1=Device Control Message
00000001
01H
= Sub-ID #2=Master Volume
* 0sssssss
SSH
= Volume LSB
0ttttttt
TTH
= Volume MSB
11110111
F7H
= End of Exclusive
or,
11110000
F0H
= Exclusive status
01111111
7FH
= Universal Real Time
0xxxnnnn
XNH
= n:Device Number, x=ignored
00000100
04H
= Sub-ID #1=Device Control Message
00000001
01H
= Sub-ID #2=Master Volume
0sssssss
SSH
= Volume LSB
0ttttttt
TTH
= Volume MSB
11110111
F7H
= End of Exclusive
When this is received, the Volume MSB will be reflected by the System parameter
MASTER VOLUME.
*
The binary expression 0sssssss is expressed in hexadecimal as SSH. The same applies
elsewhere.
2.1.1.2 Master Fine Tuning (Global tuning)
11110000
F0H
= Exclusive status
01111111
7FH
= Universal Real Time
0xxxnnnn
XNH
= ID of target device
00000100
04H
= Sub-ID #1=Device Control Message
00000011
03H
= Sub-ID #2=Master Fine Tuning
0sssssss
SSH
= Fine Tuning LSB
0ttttttt
TTH
= Fine Tuning MSB
11110111
F7H
= End of Exclusive
The value set here is relative to 440Hz and will be added to or subtracted from RPN Fine
Tuning.
When the Multi number or the tone generetor mode is changed , Fine Tuning set here will
be restored to the default value.
Fine Tuning value
LSB(SS)
MSB(TT)
00H
00H
100 ÷ 8192 x (-8192) cents
00H
40H
100 ÷ 8192 x 0 cents
7FH
7FH
100 ÷ 8192 x (+8191) cents
2.1.1.3 Master Coarse Tuning (Global tuining in semitone steps)
11110000
F0H
= Exclusive status
01111111
7FH
= Universal Real Time
0xxxnnnn
XNH
= ID of target device
00000100
04H
= Sub-ID #1=Device Control Message
00000100
04H
= Sub-ID #2=Master Coarse Tuning
00000000
00H
= Coarse Tuning LSB
0ttttttt
TTH
= Coarse Tuning MSB
11110111
F7H
= End of Exclusive
The value set here is relative to 440Hz and will be added to or subtracted from RPN
Coarse Tuning.
When the Multi nunber or the tone generetor mode is changed, Fine Tuning set here will
be restored to the default value.
Coarse Tuning Value
LSB
MSB(TT)
00H
00H
100 x (-64) cents
00H
40H
100 x 0 cents
00H
7FH
100 x (+63) cents
2.1.1.4 Global Parameter Control
2.1.1.4.1 Reverb Parameter
11110000
F0H
= Exclusive status
01111111
7FH
= Universal Real Time
0xxxnnnn
XNH
= ID of target device
00000100
04H
= Sub-ID #1=Device Control Message
00000101
05H
= Sub-ID #2=Global Parameter Control
00000001
01H
= Slot path length = 1
00000001
01H
= Parameter ID width = 1
00000001
01H
= Value width = 1
00000001
01H
= Slot path LSB = 1 (Effect 0101: Reverb)
00000001
01H
= Slot path MSB = 1
0ppppppp
PPH
= Parameter to be controlled.
0vvvvvvv
VVH
= Value for the Parameter.
11110111
F7H
= End of Exclusive
Parameter(pp) Value(vv)
Display
-------------------------------------------------------------------
pp=0 Reverb Type
0...8
0:Room S
1:Room M
2:Room L
3:Hall M
4:Hall L (default)
8:GM Plate
pp=1 Reverb Time
0...127
0.6...11.0s Refer to Table#9
2.1.1.4.2 Chorus Parameter
11110000
F0H
= Exclusive status
01111111
7FH
= Universal Real Time
0xxxnnnn
XNH
= ID of target device
00000100
04H
= Sub-ID #1=Device Control Message
00000101
05H
= Sub-ID #2=Global Parameter Control
00000001
01H
= Slot path length = 1
00000001
01H
= Parameter ID width = 1
00000001
01H
= Value width = 1
00000001
01H
= Slot path LSB = 1 (Effect 0102: Chorus)
00000010
02H
= Slot path MSB = 2
0ppppppp
PPH
= Parameter to be controlled.
0vvvvvvv
VVH
= Value for the Parameter.
11110111
F7H
= End of Exclusive
Parameter(pp)
Value(vv)Display
-------------------------------------------------------------------
pp=0 Chorus Type
0...5
0:GM Chorus1
1:GM Chorus2
2:GM Chorus3 (default)
3:GM Chorus4
4:FB Chorus
5:GM Flanger
pp=1 Mod Rate (Modulation Rate)
0...127
0...15.5 Hz Refer to Table#10
pp=2 Mod Depth (Modulation Depth) 0...127
2...127
pp=3 Feedback (Feedback Level)
0...127
0...63
pp=4 Send to Reverb
(Send Level from Chorus to Reverb)0...127
0...127