1. DL manuals
  2. Yamaha
  3. Boat
  4. VX110 Deluxe WaveRunner 2006
  5. Owner's/operator's Manual

Yamaha VX110 Deluxe WaveRunner 2006 Owner's/operator's Manual

Summary of VX110 Deluxe WaveRunner 2006

  • Page 1

    2006 waverunner vx110 sport vx110 deluxe owner’s/operator’s manual lit-18626-06-52 u.S.A. Edition read this manual carefully before operation!.

  • Page 3: To The Owner/operator

    E eju09890 to the owner/operator thank you for choosing a yamaha water- craft. This owner’s/operator’s manual contains information you will need for proper opera- tion, maintenance, and care. A thorough understanding of these simple instructions will help you to obtain maximum enjoyment from your ne...

  • Page 4: Contents

    E eju09920 contents read this owner’s/operator’s manual carefully before operating your watercraft. General and safety information 1 features and functions 2 operation 3 maintenance and care 4 troubleshooting and emergency procedures 5 appendix 6 uf1k11.Book page 3 thursday, june 2, 2005 8:45 am.

  • Page 5: General and

    E 1 eju09930 general and safety information identification numbers ............................1-1 primary identification (pri-id) number ...................................................1-1 hull identification number (hin) ............1-2 engine serial number .............................1-2 emis...

  • Page 6: Identification Numbers

    1-1 e eju18300 identification numbers record the primary identification (pri-id) number, hull identification number (hin) and engine serial number in the spaces pro- vided for assistance when ordering spare parts from a yamaha dealer. Also record and keep these id numbers in a separate place in case...

  • Page 7: Hull Identification Number

    1-2 e eju12051 hull identification number (hin) the hin is stamped on a plate 1 attached to the aft deck. Eju09971 engine serial number the engine serial number is stamped on a label 1 attached to the engine unit. Uf1k11.Book page 2 thursday, june 2, 2005 8:45 am.

  • Page 8: Emission Control

    1-3 e eju13881 emission control information this engine conforms to 2006 u.S. Envi- ronmental protection agency (epa) and/or california air resouces board (carb) reg- ulations for marine si engines. This engine is certified to operate on reg- ular unleaded gasoline. Eju21140 approval label of emissi...

  • Page 9: Star Labels

    1-4 e eju18761 star labels this watercraft is labeled with a california air resources board (carb) star label 1 . See below for a description of your particu- lar label. One star - low emission the one-star label identifies engines that meet the air resources board’s personal watercraft and outboard...

  • Page 10

    1-5 e four stars - super ultra low emission the four-star label identifies engines that meet the air resources board’s sterndrive and inboard marine engine 2009 exhaust emission standards. Personal watercraft and outboard marine engines may also comply with these standards. Engines meet- ing these s...

  • Page 11: Important Labels

    1-6 e eju09980 important labels eju13510 label location uf1k11.Book page 6 thursday, june 2, 2005 8:45 am.

  • Page 12: Warning Labels

    1-7 e eju13521 warning labels 1 2 uf1k11.Book page 7 thursday, june 2, 2005 8:45 am.

  • Page 13: (For Vx110 Deluxe Only)

    1-8 e 5 6 7 4 3 (for vx110 deluxe only) uf1k11.Book page 8 thursday, june 2, 2005 8:45 am.

  • Page 14: Other Labels

    1-9 e eju13540 other labels 9 0 8 a b c uf1k11.Book page 9 thursday, june 2, 2005 8:45 am.

  • Page 15: Safety Information

    1-10 e eju11770 safety information the safe use and operation of this watercraft is dependent upon the use of proper riding techniques, as well as upon the common sense, good judgment, and expertise of the operator. Every operator should know the following requirements before riding the watercraft. ...

  • Page 16: Cruising Limitations

    1-11 e eju10011 cruising limitations ● scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others. ● operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft. ● do not...

  • Page 17: Operation Requirements

    1-12 e ● this watercraft is not equipped with light- ing required for night operation. Do not operate the watercraft after sunset or before dawn, otherwise you increase the risk of colliding with another boat, which could result in severe injury or death. ● follow navigation rules, and state/provin-...

  • Page 18

    1-13 e ● helmets meeting snell or dot standards are required for ijsba-sanctioned races. You must decide whether to wear a hel- met while you ride for recreation. You should know that a helmet could help pro- tect you in certain kinds of accidents and that it could injure you in others. A helmet is ...

  • Page 19: Recommended Equipment

    1-14 e ● do not attempt to modify this watercraft! Modifications to your watercraft may reduce safety and reliability, and render the watercraft unsafe or illegal for use. ● attach the engine shut-off cord (lanyard) to your wrist and keep it free from the handlebars so that the engine stops if the o...

  • Page 20: Hazard Information

    1-15 e eju17810 hazard information ● never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monoxide, a colorless, odorless gas that may cause loss of consciousness and death within a short time. Always operate the watercraft in an open area. ● ...

  • Page 21

    1-16 e ● for vx110 deluxe: do not use the reverse function to slow down or stop the watercraft as it could cause you to lose control, be ejected, or impact the handlebars. You could also damage the shift mechanism. This could increase the risk of back/spinal injury (paralysis), facial injuries, and ...

  • Page 22: Water-Skiing

    1-17 e eju17820 water-skiing you can use the watercraft for water-ski- ing if it has the seating capacity to carry the operator, a rearward-facing spotter, and the water-skier when he or she is not skiing. The watercraft must also have a cleat 1 designed to pull a ski towrope; do not attach the towr...

  • Page 23

    1-18 e ● your control while pulling a skier is affected by the skier’s ability, as well as water and weather conditions. ● when preparing to pull a skier, operate the watercraft at the slowest possible speed until the watercraft is well away from the skier and slack in the towrope is taken up. Make ...

  • Page 24: Rules of The Road

    1-19 e eju11800 rules of the road yamaha watercraft is legally consid- ered a powerboat. Operation of the watercraft must be in accordance with the rules and regulations governing the waterway on which it is used. Just as there are rules that apply when you are driving on streets and highways, there...

  • Page 25: Rules When Encountering

    1-20 e rules when encountering vessels there are three main situations that you may encounter with other vessels which could lead to a collision unless the steering rules are followed: meeting: you are approaching another vessel head-on crossing: you are traveling across another vessel’s path overta...

  • Page 26: Other Special Situations

    1-21 e overtaking if you are passing another vessel, you are the give-way vessel. This means that the other vessel is expected to maintain its course and speed. You must stay out of its way until you are clear of it. Likewise, if another vessel is passing you, you should maintain your speed and dire...

  • Page 27

    1-22 e this system uses buoys and signs with distinctive shapes and colors to show regu- latory or advisory information. These mark- ers are white with black letters and orange borders. They signify speed zones, restricted areas, danger areas, and general information. Remember, markings may vary by ...

  • Page 28: To Get More Boating

    1-23 e eju11810 to get more boating safety information be informed about boating safety. Addi- tional publications and information can be obtained from many organizations, including the following. United states coast guard consumer affairs staff (g-bc) office of boating, public, and consumer affairs...

  • Page 29: Enjoy Your Watercraft

    1-24 e eju10061 enjoy your watercraft responsibly you share the areas you enjoy when riding your watercraft with others and with nature. So your enjoyment includes a responsibility to treat these other people, and the lands, waters, and wildlife with respect and courtesy. Whenever and wherever you r...

  • Page 30: Features and

    E 2 eju10070 features and functions location of main components ..............2-1 operation of controls and other functions ...................................................2-5 seat ........................................................2-5 hood ......................................................

  • Page 31: Location of Main Components

    2-1 e eju10080 location of main components 1 handlebars use to control direction. 2 seat 3 footwell use to place feet for balance. To keep proper balance while facing to the rear to watch the skier. 4 sponsons 5 gunwale 6 fuel tank filler cap 7 bow eye use to attach rope for transporting, mooring or...

  • Page 32

    2-2 e 1 stern eye use to attach rope for transporting or mooring. 2 intake grate prevents debris from getting into the jet pump. 3 reverse gate (vx110 deluxe) controls direction of jet thrust when in reverse. 4 ride plate 5 jet thrust nozzle changes the direction of jet thrust according to handlebar...

  • Page 33

    2-3 e 1 start switch push to start the engine. 2 engine shut-off switch remove the clip to stop the engine and dis- able it from starting. 3 clip insert into the engine shut-off switch to enable starting of the engine. Remove to stop the engine or prevent acci- dental starting of the engine or unaut...

  • Page 34

    2-4 e 1 air filter case 2 water separator 3 fuel tank 4 battery 5 flush hose connector use to flush the engine cooling water pas- sages. 6 electrical box protects electrical components from water. 7 oil tank 8 muffler 9 spark plugs/spark plug caps/ignition coils uf1k11.Book page 4 thursday, june 2, ...

  • Page 35: Operation of Controls and

    2-5 e eju10090 operation of controls and other functions eju10100 seat there is a seat latch 1 at the rear of the seat to remove the seat. To remove the seat: pull the seat latch up, and then pull the seat off. To install the seat: insert the projection on the front of the seat into the stay on the ...

  • Page 36: Hood

    2-6 e eju12130 hood to open the hood, pull the latch 1 up, and then lift the hood up. To close the hood, push the hood down to lock it in place. Note: @ make sure that the hood is properly secured before operating the watercraft. @ eju10120 fuel tank filler cap to remove the fuel tank filler cap 1 ,...

  • Page 37: Vx110 Deluxe)

    2-7 e eju20702 remote control transmitter (for vx110 deluxe) the yamaha security system and low- rpm mode settings are selected using the remote control transmitter. (see “yamaha security system/low-rpm mode” on page 2-14 for information on using the remote control transmitter.) caution: @ the yamah...

  • Page 38: Caution:

    2-8 e note: @ while the engine is running, input from the remote control transmitter is not received. @ this device complies with part 15 of the fcc rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any ...

  • Page 39: Engine Shut-Off Switch

    2-9 e eju10160 engine shut-off switch insert the clip 1 , on the end of the engine shut-off cord 2 , under the engine shut-off switch 3 (black button). The engine will stop automatically when the clip is removed from the switch, such as if the operator falls off the watercraft. Warning @ ● always at...

  • Page 40: Throttle Lever

    2-10 e eju10180 throttle lever squeeze the throttle lever 1 to increase engine speed. Release the throttle lever to decrease engine speed or to return it to the idle posi- tion. Eju11301 cooling water pilot outlet this watercraft is equipped with a cooling water pilot outlet. When the engine is runn...

  • Page 41: Steering System

    2-11 e eju19950 steering system your watercraft can be steered by turning the handlebars 1 in the direction you wish to travel. When the handlebars are turned, the angle of the jet thrust nozzle 2 is changed and the direction of the watercraft is changed accordingly. Since the strength of the jet th...

  • Page 42: Warning

    2-12 e eju18771 shift lever (for vx110 deluxe) the shift lever is located on the starboard (right) side of the watercraft and is used to control the reverse gate, which allows the watercraft to move in reverse or forward. When the shift lever is in the reverse posi- tion, the watercraft can be launc...

  • Page 43: Handgrip

    2-13 e eju19670 handgrip the handgrip 1 provides a handhold for boarding the watercraft and for a spotter when facing rearward. Warning @ do not use the handgrip to lift the water- craft. The watercraft could fall, which could result in severe injury. @ uf1k11.Book page 13 thursday, june 2, 2005 8:4...

  • Page 44: Yamaha Engine Management

    2-14 e eju19940 yamaha engine management system (yems) this model is equipped with an inte- grated, computerized management system that controls and adjusts ignition timing, fuel injection, engine diagnostics, and the off- throttle steering (ots) system. Eju20723 yamaha security system/ low-rpm mode...

  • Page 45

    2-15 e eju21572 yamaha security system lock and unlock modes (for vx110 deluxe) the lock and unlock modes of this system can only be selected while the engine is stopped. When the lock button 1 is pressed, the beeper sounds once. This indicates the lock mode is selected and the engine cannot be star...

  • Page 46: Caution:

    2-16 e eju21582 selecting the normal mode/ low-rpm mode (for vx110 deluxe) the normal mode and low-rpm mode can only be selected when the engine is stopped in the unlock mode. Press the unlock button for more than 4 seconds to select the normal mode or low-rpm mode. Normal mode if the beeper sounds ...

  • Page 47: Multifunction Meter

    2-17 e eju20731 multifunction meter this meter contains the following func- tions for help and convenience in operating the watercraft. 1 tachometer 2 speedometer 3 hour meter/voltmeter 4 fuel meter 5 “l-mode” indicator light (for vx110 deluxe) 6 warning light 7 fuel warning indicator 8 engine overh...

  • Page 48

    2-18 e eju17870 tachometer the engine speed (r/min) is displayed by segments. Each segment indicates a 250 r/min increment. Eju20740 speedometer the meter shows the watercraft speed against water. Note: @ to switch the speedometer display between kilometers and miles, push the select button 1 for at...

  • Page 49

    2-19 e eju21172 hour meter/voltmeter note: @ to switch the display between the hour meter and voltmeter, push the select button 1 for at least 1 second after the meter is displayed for more than 10 sec- onds. @ hour meter the hour meter is provided to make it easy to follow the maintenance schedule....

  • Page 50

    2-20 e eju20770 fuel warning indicator if the fuel remaining in the tank drops to about 13 l (3.4 us gal, 2.9 imp gal), the lowest two fuel level segments, the fuel warning indicator, and the warning light all begin to blink. The buzzer also starts sound- ing intermittently. The warning signals will...

  • Page 51: Warning

    2-21 e eju21183 engine overheat warning indicator this model is equipped with an engine overheat warning system. If the engine starts to overheat, the warn- ing light and the overheat warning indicator blink, and then come on. The buzzer also begins to sound intermittently, and then it sounds contin...

  • Page 52

    2-22 e eju20801 “security” indicator light (for vx110 deluxe) the “security” indicator light 1 comes on when the unlock mode of the yamaha security system is selected. The watercraft can be ridden normally when this light is on. (see page 2-16 for more information.) eju20811 “l-mode” indicator light...

  • Page 53: Storage Compartments

    2-23 e eju10350 storage compartments a front storage compartment and a glove compartment are provided. Note: @ ● make sure that the storage compartments are properly secured before operating the watercraft. ● the storage compartments are not designed to be waterproof. If you carry objects that must ...

  • Page 54

    2-24 e eju20821 glove compartment a glove compartment 2 is located in front of the seat. To open the glove compartment, slide the latch 1 toward you, and then lift up the lid. To close the glove compartment, push the lid down until it locks securely. For vx110 deluxe note: @ ● a removable beverage h...

  • Page 55: Operation

    E 3 eju10400 operation fuel and oil ...............................................3-1 gasoline .................................................3-1 engine oil ................................................3-3 filling the fuel tank .................................3-3 pre-operation checks ...........

  • Page 56: Fuel and Oil

    3-1 e eju17980 fuel and oil this watercraft is equipped with a 4-stroke engine. Conventional 2-stroke engine oil cannot be used. The engine utilizes an electronic fuel injection system to deliver the optimal air- fuel mixture ratio required by the engine. With optimal combustion conditions, this sys...

  • Page 57: Caution:

    3-2 e ● tighten the filler cap securely after refueling. ● if you should swallow some gasoline, inhale a lot of gasoline vapor, or get gasoline in your eyes, get immediate medical attention. ● if any gasoline spills onto your skin, immediately wash with soap and water. Change clothing if gasoline sp...

  • Page 58: Engine Oil

    3-3 e eju17990 engine oil use a combination of the recommended sae and api oil classifications shown in the chart below. Caution: @ use only 4-stroke engine oil. @ eju21200 filling the fuel tank caution: @ be careful when refueling. Avoid getting water or other contaminants in the fuel tank. Contami...

  • Page 59: Pre-Operation Checks

    3-4 e eju13460 pre-operation checks eju13470 pre-operation check list before operating this watercraft, perform the checks in the following check list. See the accompanying text in this chapter for details on how to perform the checks. Warning @ if any item in the pre-operation check list is not wor...

  • Page 60: Pre-Operation Check Points

    3-5 e eju10480 pre-operation check points eju21210 engine compartment ventilate the engine compartment before each use. To ventilate the engine compartment, remove the seat. (see page 2-5 for seat removal and installation procedures.) leave the engine compartment open for a few min- utes to allow an...

  • Page 61

    3-6 e eju21220 fuel level check the fuel system for leakage, cracks, or malfunctions before each use. (see page 4-11 for check points and correct procedures.) 1. Remove the fuel tank filler cap to release any pressure that might have built up in the fuel tank. 2. Remove the seat. (see page 2-5 for s...

  • Page 62: Caution:

    3-7 e eju21230 engine oil level check the engine oil level before each use. Caution: @ ● when checking the engine oil level on water, be careful of other watercraft, boats, swimmers, and obstacles. The water current and wind can cause the watercraft to move and lead to a colli- sion. ● when checking...

  • Page 63

    3-8 e 4. Remove the oil tank filler cap 1 , wipe the dipstick clean, and then screw the filler cap into the filler hole completely. Remove the filler cap again and check that the oil level is between the minimum level mark 3 and maximum level mark 2 on the dipstick. 5. If the oil level is below the ...

  • Page 64

    3-9 e eju19610 water separator check the water separator 1 for water. Normally the water separator is empty. The water separator retains any water entering through the fuel tank breather hose if the watercraft is capsized. If water remains in the water separator, drain it by removing the drain screw...

  • Page 65: Caution:

    3-10 e eju20581 stern drain plug check the stern drain plugs for proper installation. Caution: @ ● make sure that the stern drain plugs are tightened securely before launch- ing the watercraft. Otherwise, water may flood the engine compartment and cause the watercraft to submerge. ● clean any foreig...

  • Page 66

    3-11 e eju21610 fire extinguisher check that there is a full fire extinguisher on board. The fire extinguisher holder and cover 1 are located in the front storage compartment. To store the fire extinguisher, unhook the band 2 and remove the cover. Place the fire extinguisher in the holder, and then ...

  • Page 67: Warning

    3-12 e eju18340 throttle squeeze and release the throttle lever several times to make sure that there is no hesitation in its travel. It should be smooth over the complete range, and spring back to the idle position when released. Warning @ before starting the engine, always check the operation of t...

  • Page 68: Warning

    3-13 e eju12451 shift lever and reverse gate (for vx110 deluxe) check for proper operation of the shift lever and reverse gate. Make sure that the reverse gate goes down completely when the shift lever is pulled up. Also, make sure that the reverse gate goes up completely when the shift lever is pus...

  • Page 69: Warning

    3-14 e eju10580 jet unit carefully check the jet intake for weeds, debris, or anything else that might restrict the intake of water. If the intake is clogged, cavitation could occur, reducing jet thrust, and possibly damaging the jet pump. In some cases, the engine may overheat because of lack of co...

  • Page 70: Caution:

    3-15 e eju18352 switches caution: @ do not run the engine of the watercraft for more than 15 seconds on land with- out supplying water, otherwise the engine may overheat. @ check the start switch, the engine stop switch, and the engine shut-off switch for proper operation. Push the start switch 1 to...

  • Page 71: Operation

    3-16 e eju18360 operation warning @ before operating your watercraft, become familiar with all controls. Con- sult your yamaha dealer about any con- trol or function you do not fully understand. Failure to understand how controls work could cause an accident or prevent you from avoiding an accident....

  • Page 72: Caution:

    3-17 e 2. For the first 5 minutes, run the engine at trolling speed only. For the 30 minutes of operation after that, keep the engine speed below 5,000 r/min. For the 1 hour of operation after that, keep the engine speed below 6,500 r/min. 3. Proceed with normal operation. Caution: @ failure to foll...

  • Page 73: Starting The Engine

    3-18 e eju20841 starting the engine warning @ never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monox- ide, a colorless, odorless gas that may cause loss of consciousness and death within a short time. Always operate the watercraft in an op...

  • Page 74: Warning

    3-19 e 3. Attach the clip 1 to the engine shut-off switch 2 and attach the engine shut-off cord 3 to your left wrist. Warning @ check that the engine shut-off cord is not frayed or broken, and keep it free from the handlebars so the engine stops if the operator falls off. The engine shut-off cord ma...

  • Page 75: Stopping The Engine

    3-20 e eju10660 stopping the engine to stop the engine, release the throttle lever, and then push the engine stop switch (red button). Warning @ you need throttle to steer. Shutting off the engine can cause you to hit an obsta- cle you are attempting to avoid. A colli- sion could result in severe in...

  • Page 76: Operating Your Watercraft

    3-21 e eju10680 operating your watercraft eju11650 getting to know your watercraft operating your watercraft requires skills acquired through practice over a period of time. Take the time to learn the basic tech- niques well before attempting more difficult maneuvers. Operating your new watercraft c...

  • Page 77: Riding Watercraft With

    3-22 e wear protective clothing. Severe internal injuries can occur if water is forced into body cavities as result of falling into the water or being near the jet thrust nozzle. Normal swimwear does not adequately protect against forceful water entry into rectum and vagina. All riders must wear a w...

  • Page 78: Starting The Watercraft

    3-23 e eju18370 starting the watercraft warning @ ● scan constantly for people, objects, and other watercraft. Be alert for con- ditions that limit your visibility or block your vision of others. ● operate defensively at safe speeds and keep a safe distance away from people, objects, and other water...

  • Page 79

    3-24 e eju10730 starting and boarding in shallow water 1. Do not start the engine in less than 60 cm (2 ft) of water. Put the watercraft in water that is deep enough, and then board the watercraft from the side or the rear. 2. Attach the engine shut-off cord to your left wrist, and then install the ...

  • Page 80: Water

    3-25 e eju10750 boarding and starting in deep water warning @ ● operator and passenger should prac- tice getting on board in shallow water before riding in deep water. Boarding in deep water requires more skill. ● the fatigue and exposure that could result after unsuccessful attempts to get back on ...

  • Page 81: Warning

    3-26 e eju21132 boarding with passengers warning @ severe internal injuries can occur if water is forced into body cavities as a result of being near the jet thrust nozzle. Do not apply throttle until the passen- gers are seated with their feet on the floor of the footwell and are securely holding o...

  • Page 82

    3-27 e note: @ the heavier the total weight of the operator and passengers, the more difficult it will be to balance the watercraft. Do not operate the watercraft when the total weight exceeds 240 kg (530 lb) including any cargo. If it is difficult to balance the watercraft at a stand- still, procee...

  • Page 83: Capsized Watercraft

    3-28 e eju18102 capsized watercraft if the watercraft capsizes, turn it over immediately. Be sure to carefully follow the procedures below to prevent injury or damage to the watercraft. Warning @ improper uprighting can cause injury: ● make sure that the engine shut-off cord is removed from the engi...

  • Page 84: Caution:

    3-29 e 3. Start the engine and operate the water- craft to discharge any water remaining in the engine compartment. (if the engine does not start, see page 5-7, “towing the watercraft” or page 5-8, “submerged watercraft.”) caution: @ do not operate the engine at full throttle for at least one minute...

  • Page 85: Turning The Watercraft

    3-30 e eju19960 turning the watercraft steering control depends on the combi- nation of handlebar position and the amount of throttle. Water sucked in through the intake grate is pressurized by the impeller in the jet pump. As the pressurized water is expelled from the pump through the jet thrust no...

  • Page 86: Warning

    3-31 e warning @ ● do not release the throttle lever when trying to steer away from objects—you need throttle to steer. A collision could result in severe injury or death. ● when operating at higher speeds, make gradual turns or slow down before turning. Sharp high-speed turns may cause the watercra...

  • Page 87: Stopping The Watercraft

    3-32 e eju18501 stopping the watercraft the watercraft is not equipped with a sep- arate braking system. It is stopped by water resistance when the throttle lever is released. From full speed, the watercraft comes to a complete stop in approximately 100 m (330 ft) after the throttle is released or t...

  • Page 88: Beaching The Watercraft

    3-33 e eju10810 beaching the watercraft 1. Make sure no obstructions, boats or swimmers are near the beach. Release the throttle lever about 100 m (330 ft) before you reach the intended beaching area. 2. Approach the beach slowly and stop the engine before reaching land. Remember: you need throttle ...

  • Page 89: Reverse On Waterways (For

    3-34 e eju12541 reverse on waterways (for vx110 deluxe) reverse can be used for slow-speed maneuvering when it is necessary to back up out of tight spots where you cannot turn around. Reverse can only be used to slow down or stop during slow-speed maneuver- ing, such as when docking. Once the engine...

  • Page 90: Post-Operation Checks

    3-35 e eju13841 post-operation checks always perform the following post-opera- tion checks after operating the watercraft. 1. Remove the watercraft from the water. 2. Wash down the hull, handlebars, and jet unit with fresh water. 3. Remove the seat and check the engine compartment for water. To drai...

  • Page 91: Caution:

    3-36 e 7. If the watercraft will be stored for a week or more, lubricate internal engine com- ponents to help prevent corrosion. (see page 4-3 for lubrication procedures.) 8. Rinse the engine and engine compart- ment with a small amount of water. Caution: @ do not use high pressure when rinsing the ...

  • Page 92: Transporting

    3-37 e eju18111 transporting when transporting the watercraft on a trailer, secure the tie downs to the trailer through the bow eye and stern eye. Caution: @ ● do not route ropes or tie downs over the seat, as they may leave permanent marks on the seat’s surface. Also, wrap the ropes or tie downs wi...

  • Page 93: Maintenance and

    E 4 eju10860 maintenance and care storage ......................................................4-1 flushing the cooling system ..................4-1 lubrication ..............................................4-3 fuel system ............................................4-4 battery .......................

  • Page 94: Storage

    4-1 e eju18121 storage warning @ always place the watercraft upright in a horizontal position when storing it, oth- erwise fuel could leak out into the engine or engine compartment, which could result in a fire hazard. @ storage for prolonged periods of time, such as winter storage, requires prevent...

  • Page 95

    4-2 e 1. Put the watercraft on land in a horizontal position. 2. Remove the seat. (see page 2-5 for seat removal and installation procedures.) 3. Remove the flushing hose connector cap 1 , and then insert the garden hose adapter 2 into the flushing hose con- nector 3 and turn it until it is securely...

  • Page 96: Lubrication

    4-3 e eju21620 lubrication warning @ do not spray flammable rust inhibitor products on engine surfaces while the engine is hot. The sprayed substance or propellants could catch fire. @ 1. Remove the seat. (see page 2-5 for seat removal and installation procedures.) 2. Loosen the clamp screw 1 and di...

  • Page 97: Fuel System

    4-4 e eju19622 fuel system warning @ gasoline and its vapors are highly flammable and explosive! ● do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition. ● stop engine before refueling. ● refuel in a well-ventilated area with the watercraft in a horizontal posi...

  • Page 98: Battery

    4-5 e eju19700 battery if the watercraft will not be used for more than a month, disconnect the negative (–) lead first, then the positive (+) lead and breather hose, and then remove the battery from the watercraft. Clean the battery casing using fresh water. If the battery terminals are dirty or co...

  • Page 99: Cleaning The Watercraft

    4-6 e note: @ the condition of the battery can be known by checking the specific gravity of the elec- trolyte. However, you can also know the con- dition of the battery by measuring the voltage at both battery terminals. Charge the battery if the voltage is less than 12 volts. It is recommended to h...

  • Page 100: Maintenance and

    4-7 e eju11971 maintenance and adjustments periodic inspection, adjustment and lubri- cation will keep your watercraft in the safest and most efficient condition possible. Safety is an obligation of the watercraft owner. Proper maintenance must be carried out to keep the exhaust emission and sound l...

  • Page 101

    4-8 e ● modifications to this watercraft not approved by yamaha may cause loss of performance or excessive noise, or render it unsafe for use. Consult a yamaha dealer before attempting any changes. @ note: @ a service manual is available for purchase through a yamaha dealer for owners who have the m...

  • Page 102: And Tool Kit

    4-9 e eju18741 owner’s/operator’s manual and tool kit it is advisable always to carry the owner’s/operator’s manual and tool kit with you whenever you use the watercraft. For your convenience, a storage compart- ment 1 is provided on the watercraft for the manual and tool kit. Note: @ to protect the...

  • Page 103: Periodic Maintenance Chart

    4-10 e eju13550 periodic maintenance chart the following chart gives general guidelines for periodic maintenance. However, depend- ing on your operating conditions maintenance may need to be performed more frequently. Pmc-f1b1 ( ● ) this mark indicates maintenance that you may do yourself. ( ❍ ) thi...

  • Page 104: Inspecting The Fuel System

    4-11 e eju18160 inspecting the fuel system warning @ gasoline is highly flammable and explo- sive. Failure to check for and repair any fuel leakage could result in fire or explo- sion. A fire or explosion can cause severe injury or death. Shut off the engine. Do not smoke. Avoid spilling gasoline. F...

  • Page 105: Changing The Engine Oil

    4-12 e eju21630 changing the engine oil warning @ engine oil is extremely hot immediately after the engine is turned off. Coming into contact with or getting any engine oil on your clothes could result in burns. @ caution: @ ● do not run the engine with too much or not enough oil in the oil tank. Oi...

  • Page 106: Caution:

    4-13 e caution: @ if oil is leaking or the oil pressure warn- ing indicator comes on when the engine is running, immediately turn the engine off and have a yamaha dealer check the watercraft. Continuing to operate the engine under such conditions could cause severe engine damage. @ uf1k11.Book page ...

  • Page 107: Angle

    4-14 e eju21280 checking the air filter element have a yamaha dealer check and clean or replace the air filter element every 12 months or every 100 hours of operation. Eju18891 inspecting the jet thrust nozzle angle check for smooth operation of the handle- bars and jet thrust nozzle. Turn the handl...

  • Page 108: Vx110 Deluxe)

    4-15 e eju21290 inspecting the shift cable (for vx110 deluxe) place the shift lever in the reverse posi- tion. Make sure that the reverse gate makes contact with the stopper 1 . If the reverse gate does not make contact with the stopper, have a yamaha dealer ser- vice it. Eju11040 inspecting and adj...

  • Page 109: Cleaning and Adjusting The

    4-16 e eju21300 cleaning and adjusting the spark plugs the spark plug is an important engine component and is easy to inspect. The con- dition of the spark plug can indicate some- thing about the condition of the engine. For example, if one spark plug shows a distinctly different color, the engine c...

  • Page 110: Warning

    4-17 e measure the spark plug gap a with a wire thickness gauge. Replace the spark plug or adjust the gap to specification if nec- essary. To install a spark plug: 1. Clean the gasket surface. 2. Wipe any dirt from the threads of the spark plug. 3. Install the spark plug, and then tighten it to spec...

  • Page 111: Lubrication Points

    4-18 e eju21310 lubrication points to keep moving parts sliding or rotating smoothly, coat them with water-resistant grease. Recommended water-resistant grease: yamaha marine grease/ yamaha grease a ● throttle cable (handlebar end) pull the throttle lever and remove the seal 1 . Spray a rust inhibit...

  • Page 112

    4-19 e for vx110 deluxe: ● shift cable (reverse gate end) uf1k11.Book page 19 thursday, june 2, 2005 8:45 am.

  • Page 113: Inspecting The Battery

    4-20 e eju19710 inspecting the battery check the level of the battery electrolyte and make sure that the negative and posi- tive leads are securely tightened. Warning @ ● battery electrolyte is poisonous and dangerous, causing severe burns, etc. Electrolyte contains sulfuric acid. Avoid contact with...

  • Page 114: Caution:

    4-21 e to replenish the battery: 1. Make sure that the electrolyte level is between the upper 1 and lower 2 level marks. 2. Refill the battery with distilled water if necessary. Caution: @ normal tap water contains minerals that are harmful to a battery. Use only dis- tilled water for replenishing t...

  • Page 115: Adjusting The Fuel Injection

    4-22 e eju18231 adjusting the fuel injection system the fuel injection system was set at the yamaha factory. Have a yamaha dealer ser- vice the watercraft if necessary. Caution: @ do not attempt to adjust the fuel injection system. If the settings are changed poor engine performance and damage may r...

  • Page 116: Replacing The Fuses

    4-23 e eju21321 replacing the fuses the fuses are in the electrical box 1 . To replace a fuse: 1. Remove the cap 2 . 2. Replace the fuse 4 with the spare fuse 5 of the correct amperage by using the special tool 3 on the reverse side of the cap. Warning @ do not use fuses of higher amperage than thos...

  • Page 117: Specifications

    4-24 e eju13590 specifications model item unit vx110 sport/vx110 deluxe watercraft capacity maximum people on board number of people 3 maximum load capacity kg (lb) 240 (530) dimensions length mm (in) 3,220 (126.8) width mm (in) 1,170 (46.1) height mm (in) 1,150 (45.3) dry weight kg (lb) 325 (716) p...

  • Page 118

    4-25 e drive unit propulsion system jet pump jet pump type axial flow, single stage impeller rotation counterclockwise (viewed from rear) jet thrust nozzle horizontal angle degree 24 + 24 fuel and oil recommended fuel regular unleaded gasoline minimum octane rating pon ron 86 90 recommended engine o...

  • Page 119: Troubleshooting

    E 5 eju11150 troubleshooting and emergency procedures troubleshooting ......................................5-1 troubleshooting chart ............................5-1 emergency procedures ..........................5-3 cleaning the jet intake and impeller ......5-3 jumping the battery ...................

  • Page 120: Troubleshooting

    5-1 e eju11160 troubleshooting if you have any trouble with your watercraft, use this section to check for the possible cause. If you cannot find the cause, or if the procedure for replacement or repair is not described in this owner’s/operator’s manual, have a yamaha dealer perform the necessary se...

  • Page 121

    5-2 e engine runs irregu- larly or stalls fuel empty refill as soon as possi- ble 3-3 stale or contaminated have serviced by yamaha dealer 4-11 fuel tank water or dirt present have serviced by yamaha dealer 4-11 spark plug fouled or defective replace 4-16 incorrect heat range replace 4-16 gap incorr...

  • Page 122: Emergency Procedures

    5-3 e eju11180 emergency procedures eju21602 cleaning the jet intake and impeller if weeds or debris get caught in the intake or impeller, cavitation can occur, causing jet thrust to decrease even though engine speed rises. If this condition is allowed to continue, the engine will overheat and may s...

  • Page 123: Caution:

    5-4 e 2. Remove any weeds or debris from around the drive shaft, impeller, pump housing, and jet thrust nozzle. If debris is difficult to remove, consult your yamaha dealer. Caution: @ always avoid operating your watercraft in areas where weed growth is thick. If trav- eling in weeded areas is unavo...

  • Page 124: Jumping The Battery

    5-5 e eju18440 jumping the battery if the watercraft battery has run down, the engine can be started using a 12-volt bat- tery and jumper cables. Warning @ battery electrolyte is poisonous and dan- gerous, causing severe burns, etc. Elec- trolyte contains sulfuric acid. Avoid contact with skin, eyes...

  • Page 125: Caution:

    5-6 e eju18450 connecting the jumper cables 1. Connect the positive (+) jumper cable 1 to the positive (+) terminals of both bat- teries. 2. Connect one end of the negative (–) jumper cable 2 to the negative (–) termi- nal of the booster battery 3 . 3. Connect the other end of the negative (–) cable...

  • Page 126: Towing The Watercraft

    5-7 e eju19130 towing the watercraft if the watercraft becomes inoperative in the water, it can be towed to shore. If the watercraft must be towed in an emergency using a towline, the operator should ride the watercraft, holding onto the handlebars. Caution: @ ● tow the watercraft at 5 mph (8 km/h) ...

  • Page 127: Submerged Watercraft

    5-8 e eju19020k submerged watercraft if the watercraft is submerged or flooded with water, follow the procedure below and consult a yamaha dealer as soon as possi- ble. Failure to do so may result in serious engine damage! In an emergency: 1. Beach the watercraft and remove the stern drain plugs to ...

  • Page 128: Caution:

    5-9 e caution: @ do not start the engine even after com- pleting the previous steps. Any water remaining in the engine could cause seri- ous engine damage. @ 8. Install the spark plugs, and then connect the spark plug caps and fuel injector couplers. 9. Have the watercraft inspected by a yamaha deal...

  • Page 129: Appendix

    E 6 eju11240 appendix limited warranty ................................... 6-1 yamaha extended service (y.E.S.) .................................................. 6-3 index ..................................................... 6-4 uf1k11.Book page 1 thursday, june 2, 2005 8:45 am.

  • Page 130: Limited Warranty

    6-1 e eju11720 limited warranty lwt-nonce yamaha motor corporation, u.S.A. Watercraft limited warranty yamaha motor corporation is proud of its heritage and reputation for producing products with high standards of quality and workman- ship. Product excellence provides the cornerstone for our commitm...

  • Page 131

    6-2 e this warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Yamaha motor corporation, u.S.A. Post office box 6555 cypress, california 90630 warranty questions and answers q. What costs are my responsibility during the warranty period? A. Th...

  • Page 132

    6-3 e eju19862 yamaha extended service (y.E.S.) keep your yamaha protected even after your warranty expires with genuine yamaha extended service (y.E.S.). ● ● ● ● y.E.S. Is designed and administered by yamaha motor corporation to provide maximum owner satisfaction. You get uninterrupted factory-back...

  • Page 133: Index

    6-4 e eju11250 index a adjusting the fuel injection system ........ 4-22 approval label of emission control certificate................................................. 1-3 b battery............................................3-10, 4-5 beaching the watercraft ........................ 3-33 bilge .......

  • Page 134

    6-5 e learning to operate your watercraft ...... 3-21 leaving the watercraft........................... 3-20 limitations on who may operate the watercraft ........................................ 1-10 limited warranty...................................... 6-1 “l-mode” indicator light (for vx110 delu...

  • Page 135

    6-6 e transporting .......................................... 3-37 troubleshooting ...................................... 5-1 troubleshooting chart ............................. 5-1 turning the watercraft ........................... 3-30 u united states coast guard ................... 1-23 w warning...

  • Page 136

    Printed in usa jun. 2005—1.5 × 1 cr f1k-f8199-11 (e) printed on recycled paper yamaha motor corporation, usa.