I rev: aug2014 owner’s manual this manual contains important safety instructions for the gasoline engine powered lawnmower models: 54zb, 62zb read safety warnings and operating instructions carefully. Save this manual. When you call the help-line you will need to have the following information: date...
Ii 54zb, 62zb z- beast finish mower rev: aug2014 z- beast this manual contains important safety instructions for finish mowers read safety warnings and operating instructions carefully save these instructions. This owner’s manual is considered a permanent part of the finish mower and should remain wi...
Iii rev: aug2014 check out our other great products at www.Homedepot.Com or visit our website at www.Beastpowerequipment.Com turf beast 36-inch & 54-inch walk behind mower beast series brush master chipper/shredder with 2-way feed 100-inch tow behind mower the beast 36-inch brush mower brush beast 3...
Iv 54zb, 62zb z- beast finish mower rev: aug2014 z- beast about the beast mower manual congratulations on the purchase of your new beast commercial mower. We at gxi outdoor power are confident that this mower will provide excellent performance, outstanding quality, and great durability when operated ...
1 54zb, 62zb z- beast finish mower rev: aug2014 z- beast safety information beast lawn mowers are designed to provide safe and dependable service if operated according to instructions. Read and understand this owner’s manual before operating your lawn mower. Emission control system information the u...
2 54zb, 62zb z- beast finish mower rev: aug2014 z- beast inspection and serial number locations mower inspection for your safety, inspect the lawn mower before each use. Before you begin your inspection, be sure the following conditions are met: the lawn mower should be on a level surface, with the ...
3 54zb, 62zb z- beast finish mower rev: aug2014 z- beast preparation safety precautions preparation—safety precautions 1. Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job. Only use accessories and attachments approved by beast. 2. I...
4 54zb, 62zb z- beast finish mower rev: aug2014 z- beast operation safety precautions equipment operation—safety precautions 1. Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect. Carbon monoxide is odorless, tasteless, and can be fatal. 2. Mow only in day...
5 54zb, 62zb z- beast finish mower rev: aug2014 z- beast before attempting to use your mower, make sure you are familiar with all of the components and have read the manual. Need help? Parts, service and technical assistance call: 1-919-550-3221 www.Gxioutdoorpower.Com danger: do not bypass, modify,...
6 54zb, 62zb z- beast finish mower rev: aug2014 z- beast roll over protective structure (rops) roll over protective structure (rops) this mower is equipped with a roll over protective structure (rops) and a seat belt. Do not remove the rops or seat belt. Rops reduces the chance of injury in the even...
7 54zb, 62zb z- beast finish mower rev: aug2014 z- beast the maximum slope angle you can safely operate your mower on is 15 degrees. Do not exceed 15 degrees with your mower. 1. Line up the side of this page with a vertical object to gauge the angle of the slope. 2. Fold this sheet along the dotted ...
8 54zb, 62zb z- beast finish mower rev: aug2014 z- beast safety decals safety decal identification the labels shown below are located on your mower to warn you of potential hazards and provide you with important safety information. If these decals become difficult to read or are missing from the mower...
9 54zb, 62zb z- beast finish mower rev: aug2014 z- beast product specifications models feature 54zb 62zb product type commercial, 0-turn commercial, 0-turn cutting width 54-inch 62-inch engine see engine manufacturer’s manual see engine manufacturer’s manual engine start electric electric transmissio...
10 54zb, 62zb z- beast finish mower rev: aug2014 z- beast control panel and lawn mower components throughout this manual, instructions are given on the operation of your beast mower. We recommend that while going through this manual, you have your mower available for quick and easy access in order t...
11 54zb, 62zb z- beast finish mower rev: aug2014 z- beast missing parts request form name phone email address important! Please include your receipt. Without a receipt, your order will be delayed. You may also email us at: customerservice@gxioutdoorpower.Com fax: 1-919-550-3277 if emailing, please s...
12 54zb, 62zb z- beast finish mower rev: aug2014 z- beast operating instructions starting the engine danger: exhaust contains poisonous carbon monoxide, a colorless and odorless gas. Breathing exhaust can cause loss of consciousness and may lead to death. Do not operate the engine in a confined space...
13 54zb, 62zb z- beast finish mower rev: aug2014 z- beast operating instructions operating the mower 1. Make sure the brake has been moved to the off position. 2. Pull both control handles to the center. 3. To drive the mower forward, push both handle bars forward away from the chest. The forward sp...
14 54zb, 62zb z- beast finish mower rev: aug2014 z- beast operating instructions changing cut height your mower is equipped with an easily adjustable floating deck, which can be adjusted for cut heights of 1½ inches to 5 inches in ½-inch increments. The deck height adjuster is located on the right si...
15 54zb, 62zb z- beast finish mower rev: aug2014 z- beast disengaging hydraulic drive units before physically moving the mower when the engine is not running, the hydraulic drive units need to be disengaged into free-wheel mode. To disengage the hydraulic drive units: 1. Stand at the rear of the mow...
16 54zb, 62zb z- beast finish mower rev: aug2014 z- beast the importance of maintenance regular maintenance is essential to ensure your mower continues to deliver safe and high-quality performance. To help you properly care for your mower, the following pages include a recommended maintenance schedu...
17 54zb, 62zb z- beast finish mower rev: aug2014 z- beast item procedure time interval break-in (first 5 hrs.) every 8 hrs. (daily) every 40 hrs. (weekly) every 100 hrs. (bi-weekly) every 200 hrs. (monthly) belts inspect (adjust if needed) x x blades inspect and/or sharpen x engine air filter inspect...
18 54zb, 62zb z- beast finish mower rev: aug2014 z- beast service adjustments return to neutral danger! Make certain the engine comes to a complete stop before putting your hands in the access panel. If the mower creeps or will not stop as desired when the handles are in neutral position, adjustment...
19 54zb, 62zb z- beast finish mower rev: aug2014 z- beast 1 2 3 5 4 7 deck belt tension it is recommended to check and adjust the deck belt tension after the initial 5 hours of use on the hour meter. The new belt will seat into pulley grooves and may need adjusting. After the initial break in period...
20 54zb, 62zb z- beast finish mower rev: aug2014 z- beast 7 9 8 stop bolt figure 2 move the blade engagement handle to the “on” position. Using your hand, press the clutch pulley (7) in the direction indicated with about 20-25lbs of pressure. Ensure that the swing arm(8) stops within 1 inch to 1.5 i...
21 54zb, 62zb z- beast finish mower rev: aug2014 z- beast deck belt retainers there are 8 main deck retainers. 6 “j” shaped retainers (1, 2, 3, 4, 5, 6) 2 idle pulley retainers (7) to adjust the retainers, loosen the top nut slightly and rotate the retainer into place. After adjusting hold the retai...
22 54zb, 62zb z- beast finish mower rev: aug2014 z- beast stop bolt deck belt follow all safety precautions mentioned in this manual when doing any maintenance on your mower. The clearances for the retainers are listed below, and measured with the blades engaged and engine off. Figure 1 verifying de...
23 54zb, 62zb z- beast finish mower rev: aug2014 z- beast spindle brake inspection and replacement blade and pulley brake inspections should be performed every 100 blade on and off cycles. Before beginning service, park the mower on a level surface, turn the blades off, turn the engine off, set the ...
24 54zb, 62zb z- beast finish mower rev: aug2014 z- beast service adjustments engine-to-hydraulic drives belt adjustment (hydraulic drive input belt) the hydraulic drive input belt is located underneath the chassis at the rear of the mower. The belt should move approximately 1/8 to 3/16-inch with th...
25 54zb, 62zb z- beast finish mower rev: aug2014 z- beast hydraulic drive system adjustment the hydraulic drives are coupled to the final drives with a multi-v belt. Occasional re-tensioning of the belt may be necessary. If performance decreases or hydraulic drive control handles are activated and th...
26 54zb, 62zb z- beast finish mower rev: aug2014 z- beast service adjustments safety system adjustments warning: do not bypass, modify, alter, or disconnect the safety system. Make sure that the safety interlock system is fully operational each time before mowing. Failure to do so could present dang...
27 54zb, 62zb z- beast finish mower rev: aug2014 z- beast lubrication to ensure proper lubrication of moving parts, gxi recommends that you lubricate the following components with a high-quality, ep2 high-temperature-based grease or equivalent. Should the conditions of operation be more severe than ...
28 54zb, 62zb z- beast finish mower rev: aug2014 z- beast storage instructions short term storage let engine cool before storing and do not store near flame, high heat, and possible ignitions from sparks. Always clean off all flammable material as well as grime and dirt before storage. Never use a pre...
29 54zb, 62zb z- beast finish mower rev: aug2014 z- beast troubleshooting problem possible causes solution engine will not start 1. Key in the off position 2. Insufficient fuel in the tank 3. Air bubble in the fuel line 4. Fuel valve in off position 5. Choke not on 6. Choke linkage out of adjustment ...
30 54zb, 62zb z- beast finish mower rev: aug2014 z- beast troubleshooting problem possible causes solution mower will not move forward or reverse 1. Brake on 2. Bypass levers pulled out 3. Hydraulic drive oil has not reached optimal temperature. 1. Release brake on control panel 2. Ensure bypass pin...
31 54zb, 62zb z- beast finish mower rev: aug2014 z- beast limited warranty & service length of warranty: *(from the date of original retail purchase) residential commercial rental engine manufacturer’s warranty manufacturer’s warranty manufacturer’s warranty transmission manufacturer’s warranty manu...