1. DL manuals
  2. Z Microsystems
  3. Server
  4. ZX3
  5. User Manual

Z Microsystems ZX3 User Manual

Manual is about: ZX Series

Summary of ZX3

  • Page 1

    Z microsystems, inc. · 9820 summers ridge road, san diego, ca 92121 · t: 858.831.7000 · f: 858.831.7001 · www.Zmicro.Com zx3 : zx series server rugged rack mounted workstations & servers for deployed applications user manual.

  • Page 2: Warning

    2 regulatory information regulatory warning doc# 27-0044um rev b issued 7/13/2012 1. Use the power and video cables supplied with the product to help prevent interference with radio and television reception. The use of cables and adapters may cause interference with electronic equipment in the vicin...

  • Page 3

    3 table of contents doc# 27-0044um rev b issued 7/13/2012 table of contents section page 1.0 product overview ...........................................................................................................................................................4 1.1 about this manual ..............

  • Page 4

    4 doc# 27-0044um rev b issued 7/13/2012 1.1 about this manual this product manual will help you through the installation, setup, and operation of your zx3 server. We recommend you read this manual carefully and follow the instructions in the installation chapter for verification of system functions ...

  • Page 5

    5 doc# 27-0044um rev b issued 7/13/2012 product overview 1.2 product description highlights • supports latest intel quad core xeon & amd quad core opteron processors • 650w dual redundant ac power supply, 750w fixed dc options • 19” rack mountable • only 20 inches deep • slim 3u (5.20”) height • 12 ...

  • Page 6

    6 doc# 27-0044um rev b issued 7/13/2012 setup 2.0 setup note: for the fastest and easiest installation of the zx3 server, follow the installation guide provided with your server station. 2.2 installing the zx3 station in a rack 2.1 shipment contents ensure all of the following parts are included in ...

  • Page 7: Z Microsystems, Inc.

    7 setup doc# 27-0044um rev b issued 7/13/2012 2.3 zx3 connections guide required cables/connectors • power supply cable (ac or dc option) • video signal cable (dvi, bnc) • serial i/o connector (usb type b-a) preparations in preparation to setting up and connecting the zx3, turn off the electrical po...

  • Page 8

    8 configurations required tools • philips screwdriver doc# 27-0044um rev b issued 7/13/2012 3.0 configuring your zx3 station this section will provide information and assistance with the following topics: • updating zx3 modules and configurations • removing/re-installing lockable face plate cover • ...

  • Page 9

    9 configurations doc# 27-0044um rev b issued 7/13/2012 3.4 changing or re-installing a pci card 4. Install the new memory dimm by carefully aligning the memory dimm parallel to the slot and then gently but firmly inserting. 5. Carefully push the memory dimm in using your thumbs. 6. Secure the memory...

  • Page 10

    10 configurations doc# 27-0044um rev b issued 7/13/2012 3.6 re-installing top cover of zx3 station 1. Place cover loosely onto zx3 station. When placed on the station, make sure your side flanges properly align with the corresponding slots. 3. Use both hands to push the top cover from the rear or th...

  • Page 11

    11 configurations doc# 27-0044um rev b issued 7/13/2012 3.7 removing a power supply module note: if one of the power supply modules is removed, then the system will still operation with only one remaining power supply. Warning: a failed power supply will be identified by an audible alarm. This alarm...

  • Page 12

    12 configurations doc# 27-0044um rev b issued 7/13/2012 3.9 removing the lockable face plate cover note: the lockable face plate cover is an option available only to certain models. 3.10 installing the lockable face plate cover 1. Using the provided key, turn to the right to unlock the face plate co...

  • Page 13

    13 doc# 27-0044um rev b issued 7/13/2012 operations this section will provide information and assistance with the following topics : • powering up the zx3 station • zx3 status information & indicators • inserting & removing tranzpak2 storage modules 4.0 operations 4.1 powering on the zx3 station the...

  • Page 14

    14 doc# 27-0044um rev b issued 7/13/2012 operations 4.4 inserting the tranzpak2 storage module 4.3 removing the tranzpak2 storage module 1. Slide the locking catch towards the right to allow the locking handle to spring open. 3. Push the locking handle to the left. This will disconnect the tranzpak2...

  • Page 15

    15 warning warning be sure to turn off the power before you perform any maintenance on the server. It is recommended that users do not service the server. User maintenance is restricted to removal and installation of modules and cots parts, and to cleaning as explained below. Caution: do not use ben...

  • Page 16

    16 troubleshooting doc# 27-0044um rev b issued 7/13/2012 6.0 troubleshooting the zx3 station troubleshooting topics this section will provide information and assistance with the following topics: • troubleshooting topics for the zx3 station • frequently asked questions about the zx3n station in the ...

  • Page 17

    17 customer support note: more help, late-breaking news, and details of the latest accesories for z micro products can be found on our website at : www.Zmicro.Com note: if possible, stay by the computer. The z microsystems technical support representative may wish to go through the problem over the ...

  • Page 18

    18 customer support doc# 27-0044um rev b issued 7/13/2012 7.1 replacing parts for the zx3 station if the z microsystems technical support engineer determines that the product needs to be replaced, a customer service representative will issue a return material authorization (rma) number. An rma numbe...

  • Page 19

    19 appendix doc# 27-0044um rev b issued 7/13/2012 8.1 technical specifications for the zx3 station the zx series servers are meticulously engineered to be adaptable and suited for an array of field operations and applications. These are standard zx series specifications. Other configurations may cau...

  • Page 20: Z Microsystems, Inc.

    20 doc# 27-0044um rev b issued 7/13/2012 8.2 mechanical outlines for the zx3 station appendix 8.2.1 zx3 station front iso view rear view 17.15 20.64 2.84 20.00 0 .75 8.75 17.00 19.00 5.20 mounting holes (slide rails not installed) scale: none unit wt. Sheet of 1 size b fscm 0xwt1 dwg no. Rev title a...

  • Page 21: Z Microsystems, Inc.

    21 doc# 27-0044um rev b issued 7/13/2012 8.2.2 zx3 station - rear view (ac/dc power supply) dual redundant ac power front iso view rear view 17.15 20.64 2.84 20.00 0 .75 8.75 17.00 19.00 5.20 mounting holes (slide rails not installed) scale: none unit wt. Sheet of 1 size b fscm 0xwt1 dwg no. Rev tit...

  • Page 22

    Z microsystems, inc. · 9820 summers ridge road, san diego, ca 92121 · t: 858.831.7000 · f: 858.831.7001 · www.Zmicro.Com z microsystems, inc. 9820 summers ridge road san diego, ca 92121 phone: (858) 831-7000 fax: (858) 831-7001 website: www.Zmicro.Com copyright 2012 z microsystems, inc. All rights r...